Only record IVUsers that are dominated by simplified loop
headers. Otherwise SCEVExpander will crash while looking for a
preheader.
I previously tried to work around this in LSR itself, but that was
insufficient. This way, LSR can continue to run if some uses are not
in simple loops, as long as we don't attempt to analyze those users.
Fixes <rdar://problem/11049788> Segmentation fault: 11 in LoopStrengthReduce
llvm-svn: 152892
LSR has gradually been improved to more aggressively reuse existing code, particularly existing phi cycles. This exposed problems with the SCEVExpander's sloppy treatment of its insertion point. I applied some rigor to the insertion point problem that will hopefully avoid an endless bug cycle in this area. Changes:
- Always used properlyDominates to check safe code hoisting.
- The insertion point provided to SCEV is now considered a lower bound. This is usually a block terminator or the use itself. Under no cirumstance may SCEVExpander insert below this point.
- LSR is reponsible for finding a "canonical" insertion point across expansion of different expressions.
- Robust logic to determine whether IV increments are in "expanded" form and/or can be safely hoisted above some insertion point.
Fixes PR11783: SCEVExpander assert.
llvm-svn: 148535
It's becoming clear that LoopSimplify needs to unconditionally create loop preheaders. But that is a bigger fix. For now, continuing to hack LSR.
Fixes rdar://10701050 "Cannot split an edge from an IndirectBrInst" assert.
llvm-svn: 148288
These heuristics are sufficient for enabling IV chains by
default. Performance analysis has been done for i386, x86_64, and
thumbv7. The optimization is rarely important, but can significantly
speed up certain cases by eliminating spill code within the
loop. Unrolled loops are prime candidates for IV chains. In many
cases, the final code could still be improved with more target
specific optimization following LSR. The goal of this feature is for
LSR to make the best choice of induction variables.
Instruction selection may not completely take advantage of this
feature yet. As a result, there could be cases of slight code size
increase.
Code size can be worse on x86 because it doesn't support postincrement
addressing. In fact, when chains are formed, you may see redundant
address plus stride addition in the addressing mode. GenerateIVChains
tries to compensate for the common cases.
On ARM, code size increase can be mitigated by using postincrement
addressing, but downstream codegen currently misses some opportunities.
llvm-svn: 147826
After collecting chains, check if any should be materialized. If so,
hide the chained IV users from the LSR solver. LSR will only solve for
the head of the chain. GenerateIVChains will then materialize the
chained IV users by computing the IV relative to its previous value in
the chain.
In theory, chained IV users could be exposed to LSR's solver. This
would be considerably complicated to implement and I'm not aware of a
case where we need it. In practice it's more important to
intelligently prune the search space of nontrivial loops before
running the solver, otherwise the solver is often forced to prune the
most optimal solutions. Hiding the chained users does this well, so
that LSR is more likely to find the best IV for the chain as a whole.
llvm-svn: 147801
This collects a set of IV uses within the loop whose values can be
computed relative to each other in a sequence. Following checkins will
make use of this information.
llvm-svn: 147797
This will be more important as we extend the LSR pass in ways that don't rely on the formula solver. In particular, we need it for constructing IV chains.
llvm-svn: 147724
LoopSimplify may not run on some outer loops, e.g. because of indirect
branches. SCEVExpander simply cannot handle outer loops with no preheaders.
Fixes rdar://10655343 SCEVExpander segfault.
llvm-svn: 147718
Since we're not rewriting IVs in other loops, there's not much reason
to consider their stride when generating formulae.
This should reduce the number of useless formulas considered by LSR.
llvm-svn: 146302
It's always good to prune early, but formulae that are unsatisfactory
in their own right need to be removed before running any other pruning
heuristics. We easily avoid generating such formulae, but we need them
as an intermediate basis for forming other good formulae.
llvm-svn: 145906
Someone more familiar with LSR should double-check that the extra cast is actually doing the right thing in the overflow cases; I'm not completely confident that's that case.
llvm-svn: 141916
This handles the case in which LSR rewrites an IV user that is a phi and
splits critical edges originating from a switch.
Fixes <rdar://problem/6453893> LSR is not splitting edges "nicely"
llvm-svn: 141059
Rewriting the entire loop nest now requires -enable-lsr-nested.
See PR11035 for some performance data.
A few unit tests specifically test nested LSR, and are now under a flag.
llvm-svn: 140762
The minor bug heuristic was noticed by inspection. I added the
isLoser/isValid helpers because they will become more
important with subsequent checkins.
llvm-svn: 140580
No functionality enabled by default. Use -disable-iv-rewrite.
Extended IVUsers to keep track of the phi that represents the users' IV.
Added the WidenIV transform to replace a narrow IV with a wide IV
by doing a one-for-one replacement of IV users instead of expanding the
SCEV expressions. [sz]exts are removed and truncs are inserted.
llvm-svn: 131744
model constants which can be added to base registers via add-immediate
instructions which don't require an additional register to materialize
the immediate.
llvm-svn: 130743
Now that we have a first-class way to represent unaligned loads, the unaligned
load intrinsics are superfluous.
First part of <rdar://problem/8460511>.
llvm-svn: 129401
properties.
Added the self-wrap flag for SCEV::AddRecExpr.
A slew of temporary FIXMEs indicate the intention of the no-self-wrap flag
without changing behavior in this revision.
llvm-svn: 127590
Andrew Trick