After much back and forth, I decided to deviate from ARM design and split LDR into 4 instructions (r + imm12, r + imm8, r + r << imm12, constantpool). The advantage of this is 1) it follows the latest ARM technical manual, and 2) makes it easier to reduce the width of the instruction later. The down side is this creates more inconsistency between the two sub-targets. We should split ARM LDR instruction in a similar fashion later. I've added a README entry for this.
llvm-svn: 74420
predicate does not check if Thumb mode is enabled, and when in ARM mode
there are still some checks for constant-pool use that need to run.
llvm-svn: 73887
When compiling in Thumb mode, only the low (R0-R7) registers are available
for most instructions. Breaking the low registers into a new register class
handles this. Uses of R12, SP, etc, are handled explicitly where needed
with copies inserted to move results into low registers where the rest of
the code generator can deal with them.
llvm-svn: 68545
and into the ScheduleDAGInstrs class, so that they don't get
destructed and re-constructed for each block. This fixes a
compile-time hot spot in the post-pass scheduler.
To help facilitate this, tidy and do some minor reorganization
in the scheduler constructor functions.
llvm-svn: 62275
priority function. Instead, just iterate over the AllNodes list, which is
already in topological order. This eliminates a fair amount of bookkeeping,
and speeds up the isel phase by about 15% on many testcases.
The impact on most targets is that AddToISelQueue calls can be simply removed.
In the x86 target, there are two additional notable changes.
The rule-bending AND+SHIFT optimization in MatchAddress that creates new
pre-isel nodes during isel is now a little more verbose, but more robust.
Instead of either creating an invalid DAG or creating an invalid topological
sort, as it has historically done, it can now just insert the new nodes into
the node list at a position where they will be consistent with the topological
ordering.
Also, the address-matching code has logic that checked to see if a node was
"already selected". However, when a node is selected, it has all its uses
taken away via ReplaceAllUsesWith or equivalent, so it won't recieve any
further visits from MatchAddress. This code is now removed.
llvm-svn: 58748
flag. Then in a debugger developers can set breakpoints at these calls
to see waht is about to be selected and what the resulting subgraph
looks like. This really helps when debugging instruction selection.
llvm-svn: 58278
Instead, just create one, and make sure everything that needs
it can access it. Previously most of the SelectionDAGISel
subclasses all had their own TargetLowering object, which was
redundant with the TargetLowering object in the TargetMachine
subclasses, except on Sparc, where SparcTargetMachine
didn't have a TargetLowering object. Change Sparc to work
more like the other targets here.
llvm-svn: 57016
process up to a higher level. This allows FastISel to leverage
more of SelectionDAGISel's infastructure, such as updating Machine
PHI nodes.
Also, implement transitioning from SDISel back to FastISel in
the middle of a block, so it's now possible to go back and
forth. This allows FastISel to hand individual CallInsts and other
complicated things off to SDISel to handle, while handling the rest
of the block itself.
To help support this, reorganize the SelectionDAG class so that it
is allocated once and reused throughout a function, instead of
being completely reallocated for each block.
llvm-svn: 55219
replacement of multiple values. This is slightly more efficient
than doing multiple ReplaceAllUsesOfValueWith calls, and theoretically
could be optimized even further. However, an important property of this
new function is that it handles the case where the source value set and
destination value set overlap. This makes it feasible for isel to use
SelectNodeTo in many very common cases, which is advantageous because
SelectNodeTo avoids a temporary node and it doesn't require CSEMap
updates for users of values that don't change position.
Revamp MorphNodeTo, which is what does all the work of SelectNodeTo, to
handle operand lists more efficiently, and to correctly handle a number
of corner cases to which its new wider use exposes it.
This commit also includes a change to the encoding of post-isel opcodes
in SDNodes; now instead of being sandwiched between the target-independent
pre-isel opcodes and the target-dependent pre-isel opcodes, post-isel
opcodes are now represented as negative values. This makes it possible
to test if an opcode is pre-isel or post-isel without having to know
the size of the current target's post-isel instruction set.
These changes speed up llc overall by 3% and reduce memory usage by 10%
on the InstructionCombining.cpp testcase with -fast and -regalloc=local.
llvm-svn: 53728
and better control the abstraction. Rename the type
to MVT. To update out-of-tree patches, the main
thing to do is to rename MVT::ValueType to MVT, and
rewrite expressions like MVT::getSizeInBits(VT) in
the form VT.getSizeInBits(). Use VT.getSimpleVT()
to extract a MVT::SimpleValueType for use in switch
statements (you will get an assert failure if VT is
an extended value type - these shouldn't exist after
type legalization).
This results in a small speedup of codegen and no
new testsuite failures (x86-64 linux).
llvm-svn: 52044
Evan Cheng