load commands.
The existing test case in test/Object/macho-invalid.test for
macho-invalid-too-small-segment-load-command has a cmdsize of 55, while
being too small also it is not a multiple of 4. So when that check is added
this test case will produce a different error. So I constructed a new test case
that will trigger the intended error.
I also changed the error message to be consistent with the other malformed Mach-O
file error messages which prints the load command index. I also removed both
object_error::macho_load_segment_too_small and
object_error::macho_load_segment_too_many_sections from Object/Error.h
as they are not needed and can just use object_error::parse_failed and let the
error message string distinguish the specific error.
llvm-svn: 268652
Produce another specific error message for a malformed Mach-O file when a symbol’s
section index is more than the number of sections. The existing test case in test/Object/macho-invalid.test
for macho-invalid-section-index-getSectionRawName now reports the error with the message indicating
that a symbol at a specific index has a bad section index and that bad section index value.
Again converting interfaces to Expected<> from ErrorOr<> does involve
touching a number of places. Where the existing code reported the error with a
string message or an error code it was converted to do the same.
Also there some were bugs in the existing code that did not deal with the
old ErrorOr<> return values. So now with Expected<> since they must be
checked and the error handled, I added a TODO and a comment:
"// TODO: Actually report errors helpfully" and a call something like
consumeError(NameOrErr.takeError()) so the buggy code will not crash
since needed to deal with the Error.
llvm-svn: 268298
Two problems, 1) for the last 4 bytes it would print them as separate bytes not a word
and 2) it would print the same last byte for those bytes less than a word.
rdar://25938224
llvm-svn: 267819
Before we printed a warning to stderr and left the actual output stream in a
mess. This tries to print a .long or .short representation of what we saw (as
if there was a data-in-code directive).
This isn't guaranteed to restore synchronization in Thumb-mode (if the invalid
instruction was supposed to be 32-bits, we may be off-by-16 for the rest of the
function). But there's no certain way to deal with that, and it's invalid code
anyway (if the data really wasn't an instruction, the user can add proper
.data_in_code directives if they care)
llvm-svn: 267250
Only one consumer (llvm-objdump) actually cared about the fact that there were
two triples. Others were actively working around the fact that the Triple
returned by getArch might have been invalid. As for llvm-objdump, it needs to
be acutely aware of both Triples anyway, so being generic in the exposed API is
no benefit.
Also rename the version of getArch returning a Triple. Users were having to
pass an unwanted nullptr to disambiguate the two, which was nasty.
The only functional change here is that armv7m and armv7em object files no
longer crash llvm-objdump.
llvm-svn: 267249
I'm for some reason having a problem producing a test.
It should be the same as test/MC/X86/invalid_opcode.s,
but llvm-mc seems to ignore random bytes.
llvm-svn: 267225
Showed up in running on a large binary with the missing section. I could create a fake
test case if anyone really wants but the fix is pretty obvious.
rdar://25837034
llvm-svn: 267037
Produce another specific error message for a malformed Mach-O file when a symbol’s
string index is past the end of the string table. The existing test case in test/Object/macho-invalid.test
for macho-invalid-symbol-name-past-eof now reports the error with the message indicating
that a symbol at a specific index has a bad sting index and that bad string index value.
Again converting interfaces to Expected<> from ErrorOr<> does involve
touching a number of places. Where the existing code reported the error with a
string message or an error code it was converted to do the same. There is some
code for this that could be factored into a routine but I would like to leave that for
the code owners post-commit to do as they want for handling an llvm::Error. An
example of how this could be done is shown in the diff in
lib/ExecutionEngine/RuntimeDyld/RuntimeDyldImpl.h which had a Check() routine
already for std::error_code so I added one like it for llvm::Error .
Also there some were bugs in the existing code that did not deal with the
old ErrorOr<> return values. So now with Expected<> since they must be
checked and the error handled, I added a TODO and a comment:
“// TODO: Actually report errors helpfully” and a call something like
consumeError(NameOrErr.takeError()) so the buggy code will not crash
since needed to deal with the Error.
Note there fixes needed to lld that goes along with this that I will commit right after this.
So expect lld not to built after this commit and before the next one.
llvm-svn: 266919
Removed some unused headers, replaced some headers with forward class declarations.
Found using simple scripts like this one:
clear && ack --cpp -l '#include "llvm/ADT/IndexedMap.h"' | xargs grep -L 'IndexedMap[<]' | xargs grep -n --color=auto 'IndexedMap'
Patch by Eugene Kosov <claprix@yandex.ru>
Differential Revision: http://reviews.llvm.org/D19219
From: Mehdi Amini <mehdi.amini@apple.com>
llvm-svn: 266595
Reenable reverted r265550 with endianness issue fixed. Variables of
endian-aware types such as ulittle32_t should be explicitly casted
to their natural equivalent types before passing it as vararg to
printf like functions (format in my case). Added lit config file
depending on AMDGPU target as the testcase uses assembler.
Differential revision: http://reviews.llvm.org/D16998
llvm-svn: 265645
Produce the first specific error message for a malformed Mach-O file describing
the problem instead of the generic message for object_error::parse_failed of
"Invalid data was encountered while parsing the file”. Many more good error
messages will follow after this first one.
This is built on Lang Hames’ great work of adding the ’Error' class for
structured error handling and threading Error through MachOObjectFile
construction. And making createMachOObjectFile return Expected<...> .
So to to get the error to the llvm-obdump tool, I changed the stack of
these methods to also return Expected<...> :
object::ObjectFile::createObjectFile()
object::SymbolicFile::createSymbolicFile()
object::createBinary()
Then finally in ParseInputMachO() in MachODump.cpp the error can
be reported and the specific error message can be printed in llvm-objdump
and can be seen in the existing test case for the existing malformed binary
but with the updated error message.
Converting these interfaces to Expected<> from ErrorOr<> does involve
touching a number of places. To contain the changes for now use of
errorToErrorCode() and errorOrToExpected() are used where the callers
are yet to be converted.
Also there some were bugs in the existing code that did not deal with the
old ErrorOr<> return values. So now with Expected<> since they must be
checked and the error handled, I added a TODO and a comment:
“// TODO: Actually report errors helpfully” and a call something like
consumeError(ObjOrErr.takeError()) so the buggy code will not crash
since needed to deal with the Error.
Note there is one fix also needed to lld/COFF/InputFiles.cpp that goes along
with this that I will commit right after this. So expect lld not to built
after this commit and before the next one.
llvm-svn: 265606
This reverts commit r265550. There're problems with endianness on dumping instruction bytes. Need to find out how to use support::ulittle32_t type properly.
llvm-svn: 265554
in the test suite. While this is not really an interesting tool and option to run
on a Mach-O file to show the symbol table in a generic libObject format
it shouldn’t crash.
The reason for the crash was in MachOObjectFile::getSymbolType() when it was
calling MachOObjectFile::getSymbolSection() without checking its return value
for the error case.
What makes this fix require a fair bit of diffs is that the method getSymbolType() is
in the class ObjectFile defined without an ErrorOr<> so I needed to add that all
the sub classes. And all of the uses needed to be updated and the return value
needed to be checked for the error case.
The MachOObjectFile version of getSymbolType() “can” get an error in trying to
come up with the libObject’s internal SymbolRef::Type when the Mach-O symbol
symbol type is an N_SECT type because the code is trying to select from the
SymbolRef::ST_Data or SymbolRef::ST_Function values for the SymbolRef::Type.
And it needs the Mach-O section to use isData() and isBSS to determine if
it will return SymbolRef::ST_Data.
One other possible fix I considered is to simply return SymbolRef::ST_Other
when MachOObjectFile::getSymbolSection() returned an error. But since in
the past when I did such changes that “ate an error in the libObject code” I
was asked instead to push the error out of the libObject code I chose not
to implement the fix this way.
As currently written both the COFF and ELF versions of getSymbolType()
can’t get an error. But if isReservedSectionNumber() wanted to check for
the two known negative values rather than allowing all negative values or
the code wanted to add the same check as in getSymbolAddress() to use
getSection() and check for the error then these versions of getSymbolType()
could return errors.
At the end of the day the error printed now is the generic “Invalid data was
encountered while parsing the file” for object_error::parse_failed. In the
future when we thread Lang’s new TypedError for recoverable error handling
though libObject this will improve. And where the added // Diagnostic(…
comment is, it would be changed to produce and error message
like “bad section index (42) for symbol at index 8” for this case.
llvm-svn: 264187
In executable and shared object ELF files, relocations in the file contain the final virtual address rather than section offset so this is adjusted to display section offset.
Differential revision: http://reviews.llvm.org/D15965
llvm-svn: 263971
It might be hard to recognize a hexadecimal number without '0x' prefix.
Besides that '0x' prefix corresponds to GNU objdump behaviour.
Differential Revision: http://reviews.llvm.org/D18207
llvm-svn: 263705
The PE TLS directory contains information about where the TLS data
resides in the image, what functions should be executed when threads are
created, etc.
llvm-svn: 263537
Summary:
This patch is provided in preparation for removing autoconf on 1/26. The proposal to remove autoconf on 1/26 was discussed on the llvm-dev thread here: http://lists.llvm.org/pipermail/llvm-dev/2016-January/093875.html
"I felt a great disturbance in the [build system], as if millions of [makefiles] suddenly cried out in terror and were suddenly silenced. I fear something [amazing] has happened."
- Obi Wan Kenobi
Reviewers: chandlerc, grosbach, bob.wilson, tstellarAMD, echristo, whitequark
Subscribers: chfast, simoncook, emaste, jholewinski, tberghammer, jfb, danalbert, srhines, arsenm, dschuff, jyknight, dsanders, joker.eph, llvm-commits
Differential Revision: http://reviews.llvm.org/D16471
llvm-svn: 258861
llvm-objdump when printing the Mach Header to print the unknown
cputype and cpusubtype fields as decimal instead of not printing
them at all. And change the test to check for that.
llvm-svn: 258826
When we arrive at the end of the function, the validation of
the object has been done already. In theory, so, we should never
arrive here with something broken as the object isn't mutated.
Practice sometimes proves theory to be wrong, so leave an assertion
instead, as suggested by David Blaikie, to catch bugs.
llvm-svn: 257570
to only print the first private header.
Which for Mach-O files only prints the Mach header and not the subsequent load
commands. Which is used by scripts to match what the darwin otool(1) with the
-h flag does without the -l flag.
For non-Mach-O files it has the same functionality as -private-headers (with
the trailing ’s’).
rdar://24158331
llvm-svn: 257548
A request has been made to the official registry, but an official value is
not yet available. This patch uses a temporary value in order to support
development. When an official value is recieved, the value of EM_WEBASSEMBLY
will be updated.
llvm-svn: 257517
LLVM MC has single methods which can handle the output of EH frame and DWARF CIE's and FDE's.
This code improves DWARFDebugFrame::parse to do the same for parsing.
This also allows llvm-objdump to support the --dwarf=frames option which objdump supports. This
option dumps the .eh_frame section using the new code in DWARFDebugFrame::parse.
http://reviews.llvm.org/D15535
Reviewed by Rafael Espindola.
llvm-svn: 256008
This code adds some simple decoding of the FDE's in an eh_frame.
There's still more to be done in terms of error handling and verification.
Also, we need to be able to decode the CFI's.
llvm-svn: 255550
This is the start of work to dump the contents of the eh_frame section.
It currently emits CIE entries. FDE entries will come later.
It also needs improved error checking which will follow soon.
http://reviews.llvm.org/D15502
Reviewed by Kevin Enderby and Lang Hames.
llvm-svn: 255546
Kevin Enderby