We currently default to using either generic shuffles or MASK+PACKUS/PACKSS to truncate all integer vectors. For vector comparisons, we know that the result will be either all or zero bits in every element, which can be efficiently truncated by directly using PACKSS to repeatedly halve the size of each element.
Due to the limited input values (-1 or 0) we don't need to account for vector element size, so for simplicity we just use the PACKSS(vXi16,vXi16) implementation in all cases. Additionally for AVX2 PACKSS of 256bit data we must perform a PERMQ shuffle to reorder the data into the correct order. I did investigate performing a single shuffle after all the PACKSS calls but the need to cross 128bit lanes makes this difficult to achieve efficiently.
We avoid performing this on AVX512 as it should have better alternative truncation instructions.
Differential Revision: https://reviews.llvm.org/D22814
llvm-svn: 277132
Presently, CodeGenPrepare deletes all nearly empty (only phi and branch)
basic blocks. This pass can delete loop preheaders which frequently creates
critical edges. A preheader can be a convenient place to spill registers to
the stack. If the entrance to a loop body is a critical edge, then spills
may occur in the loop body rather than immediately before it. This patch
protects loop preheaders from deletion in CodeGenPrepare even if they are
nearly empty.
Since the patch alters the CFG, it affects a large number of test cases.
In most cases, the changes are merely cosmetic (basic blocks have different
names or instruction orders change slightly). I am somewhat concerned about
the test/CodeGen/Mips/brdelayslot.ll test case. If the loop preheader is not
deleted, then the MIPS backend does not take advantage of a branch delay
slot. Consequently, I would like some close review by a MIPS expert.
The patch also partially subsumes D16893 from George Burgess IV. George
correctly notes that CodeGenPrepare does not actually preserve the dominator
tree. I think the dominator tree was usually not valid when CodeGenPrepare
ran, but I am using LoopInfo to mark preheaders, so the dominator tree is
now always valid before CodeGenPrepare.
Author: Tom Jablin (tjablin)
Reviewers: hfinkel george.burgess.iv vkalintiris dsanders kbarton cycheng
http://reviews.llvm.org/D16984
llvm-svn: 265397
autogenerated.
Also update existing test cases which appear to be generated by it and
weren't modified (other than addition of the header) by rerunning it.
llvm-svn: 253917
Function LowerVSETCC (in X86ISelLowering.cpp) worked under the wrong
assumption that for non-AVX512 targets, the source type and destination type
of a type-legalized setcc node were always the same type.
This assumption was unfortunately incorrect; the type legalizer is not always
able to promote the return type of a setcc to the same type as the first
operand of a setcc.
In the case of a vsetcc node, the legalizer firstly checks if the first input
operand has a legal type. If so, then it promotes the return type of the vsetcc
to that same type. Otherwise, the return type is promoted to the 'next legal
type', which, for vectors of MVT::i1 is always a 128-bit integer vector type.
Example (-mattr=+avx):
%0 = trunc <8 x i32> %a to <8 x i23>
%1 = icmp eq <8 x i23> %0, zeroinitializer
The initial selection dag for the code above is:
v8i1 = setcc t5, t7, seteq:ch
t5: v8i23 = truncate t2
t2: v8i32,ch = CopyFromReg t0, Register:v8i32 %vreg1
t7: v8i32 = build_vector of all zeroes.
The type legalizer would firstly check if 't5' has a legal type. If so, then it
would reuse that same type to promote the return type of the setcc node.
Unfortunately 't5' is of illegal type v8i23, and therefore it cannot be used to
promote the return type of the setcc node. Consequently, the setcc return type
is promoted to v8i16. Later on, 't5' is promoted to v8i32 thus leading to the
following dag node:
v8i16 = setcc t32, t25, seteq:ch
where t32 and t25 are now values of type v8i32.
Before this patch, function LowerVSETCC would have wrongly expanded the setcc
to a single X86ISD::PCMPEQ. Surprisingly, ISel was still able to match an
instruction. In our case, ISel would have matched a VPCMPEQWrr:
t37: v8i16 = X86ISD::VPCMPEQWrr t36, t25
However, t36 and t25 are both VR256, while the result type is instead of class
VR128. This inconsistency ended up causing the insertion of COPY instructions
like this:
%vreg7<def> = COPY %vreg3; VR128:%vreg7 VR256:%vreg3
Which is an invalid full copy (not a sub register copy).
Eventually, the backend would have hit an UNREACHABLE "Cannot emit physreg copy
instruction" in the attempt to expand the malformed pseudo COPY instructions.
This patch fixes the problem adding the missing logic in LowerVSETCC to handle
the corner case of a setcc with 128-bit return type and 256-bit operand type.
This problem was originally reported by Dimitry as PR25080. It has been latent
for a very long time. I have added the minimal reproducible from that bugzilla
as test setcc-lowering.ll.
Differential Revision: http://reviews.llvm.org/D13660
llvm-svn: 250085
Simon Pilgrim