The changes in r223113 (ARM modified-immediate syntax) have broken
instructions like:
mov r0, #~0xffffff00
The problem is that I've added a spurious range check on the immediate
operand to ensure that it lies between INT32_MIN and UINT32_MAX. While
this range check is correct in theory, it causes problems because the
operand is stored in an int64_t (by MC). So valid 32-bit constants like
\#~0xffffff00 become out of range. The solution is to simply remove this
range check. It is not possible to validate the range of the immediate
operand with the current setup because: 1) The operand is stored in an
int64_t by MC, 2) The immediate can be of the forms #imm, #-imm, #~imm
or even #((~imm)) etc. So we just chop the value to 32 bits and use it.
Also noted that the original range check was note tested by any of the
unit tests. I've added a new test to cover #~imm kind of operands.
Change-Id: I411e90d84312a2eff01b732bb238af536c4a7599
llvm-svn: 228920
Instructions of the form [ADD Rd, pc, #imm] are manually aliased
in processInstruction() to use ADR. To accomodate this, mod_imm handling
had to be tweaked a bit. Turns out it was the manual aliasing that must
be tweaked to accommodate mod_imms instead. More information about the
parsed instruction is available at the point where processInstruction()
is invoked, which makes it easier to detect a mod_imm at that point rather
than trying to detect a potential alias when a mod_imm is being prepped.
Added a test case and fixed some white spaces as well.
llvm-svn: 223772
No functional changes. Got myself bitten in r223113 when adding support for
modified immediate syntax (regressions reported by joerg@britannica.bec.de,
fixes in r223366 and r223381). Our assembler tests did not cover serveral
different syntax variants. This patch expands the test coverage to check for
the following cases:
1. Modified immediate operands may be expressed with expressions, as in #(4 * 2)
instead of #8.
2. Modified immediate operands may be _optionally_ prefixed by a '#' symbol or a
'$' symbol.
3. Certain instructions (e.g. ADD) support single input register variants;
[ADD r0, #mod_imm] is same as [ADD r0, r0, #mod_imm].
4. Certain instructions have aliases which convert plain immediates to modified
immediates. For an example, [ADD r0, -10] is not valid because -10 (in two's
complement) cannot be encoded as a modified immediate, but ARMInstrInfo.td
defines an alias which can transform this into a [SUB r0, 10].
llvm-svn: 223475
r223113 added support for ARM modified immediate assembly syntax. Which
assumes all immediate operands are prefixed with a '#'. This assumption
is wrong as per the ARMARM - which recommends that all '#' characters be
treated optional. The current patch fixes this regression and adds a test
case. A follow-up patch will expand the test coverage to other instructions.
llvm-svn: 223381
r223113 added support for ARM modified immediate assembly syntax. That patch
has broken support for immediate expressions, as in:
add r0, #(4 * 4)
It wasn't caught because we don't have any tests for this feature. This patch
fixes this regression and adds test cases.
llvm-svn: 223366
Certain ARM instructions accept 32-bit immediate operands encoded as a 8-bit
integer value (0-255) and a 4-bit rotation (0-30, even). Current ARM assembly
syntax support in LLVM allows the decoded (32-bit) immediate to be specified
as a single immediate operand for such instructions:
mov r0, #4278190080
The ARMARM defines an extended assembly syntax allowing the encoding to be made
more explicit, as in:
mov r0, #255, #8 ; (same 32-bit value as above)
The behaviour of the two instructions can be different w.r.t flags, which is
documented under "Modified immediate constants" in ARMARM. This patch enables
support for this extended syntax at the MC layer.
llvm-svn: 223113
The mapping between SRS pseudo-instructions and SRS native instructions was incorrect, the correct mapping is:
srsfa -> srsib
srsea -> srsia
srsfd -> srsdb
srsed -> srsda
This fixes <rdar://problem/14214734>.
llvm-svn: 185155
algorithm when assigning EnumValues to the synthesized registers.
The current algorithm, LessRecord, uses the StringRef compare_numeric
function. This function compares strings, while handling embedded numbers.
For example, the R600 backend registers are sorted as follows:
T1
T1_W
T1_X
T1_XYZW
T1_Y
T1_Z
T2
T2_W
T2_X
T2_XYZW
T2_Y
T2_Z
In this example, the 'scaling factor' is dEnum/dN = 6 because T0, T1, T2
have an EnumValue offset of 6 from one another. However, in other parts
of the register bank, the scaling factors are different:
dEnum/dN = 5:
KC0_128_W
KC0_128_X
KC0_128_XYZW
KC0_128_Y
KC0_128_Z
KC0_129_W
KC0_129_X
KC0_129_XYZW
KC0_129_Y
KC0_129_Z
The diff lists do not work correctly because different kinds of registers have
different 'scaling factors'. This new algorithm, LessRecordRegister, tries to
enforce a scaling factor of 1. For example, the registers are now sorted as
follows:
T1
T2
T3
...
T0_W
T1_W
T2_W
...
T0_X
T1_X
T2_X
...
KC0_128_W
KC0_129_W
KC0_130_W
...
For the Mips and R600 I see a 19% and 6% reduction in size, respectively. I
did see a few small regressions, but the differences were on the order of a
few bytes (e.g., AArch64 was 16 bytes). I suspect there will be even
greater wins for targets with larger register files.
Patch reviewed by Jakob.
rdar://14006013
llvm-svn: 185094
Unfortunately this addresses two issues (by the time I'd disentangled the logic
it wasn't worth putting it back to half-broken):
+ Coprocessor instructions should all be predicable in Thumb mode.
+ BKPT should never be predicable.
llvm-svn: 184965
The cdp2 instruction should have the same restrictions as cdp on the
co-processor registers.
VFP instructions on v8/AArch32 share the same encoding space as cdp2.
llvm-svn: 184445
"When assembling to the ARM instruction set, the .N qualifier produces
an assembler error and the .W qualifier has no effect."
In the pre-matcher handler in the asm parser the ".w" (wide) qualifier
when in ARM mode is now discarded. And an error message is now
produced when the ".n" (narrow) qualifier is used in ARM mode.
Test cases for these were added.
rdar://14064574
llvm-svn: 184224
"hint" space for Thumb actually overlaps the encoding space of the CPS
instruction. In actuality, hints can be defined as CPS instructions where imod
and M bits are all nil.
Handle decoding of permitted nop-compatible hints (i.e. nop, yield, wfi, wfe,
sev) in DecodeT2CPSInstruction.
This commit adds a proper diagnostic message for Imm0_4 and updates all tests.
Patch by Mihail Popa <Mihail.Popa@arm.com>.
llvm-svn: 180617
The reference manual defines only 5 permitted values for the immediate field of the "hint" instruction:
1. nop (imm == 0)
2. yield (imm == 1)
3. wfe (imm == 2)
4. wfi (imm == 3)
5. sev (imm == 4)
Therefore, restrict the permitted values for the "hint" instruction to 0 through 4.
Patch by Mihail Popa <Mihail.Popa@arm.com>
llvm-svn: 179707
According to the ARM reference manual, constant offsets are mandatory for pre-indexed addressing modes.
The MC disassembler was not obeying this when the offset is 0.
It was producing instructions like: str r0, [r1]!.
Correct syntax is: str r0, [r1, #0]!.
This change modifies the dumping of operands so that the offset is always printed, regardless of its value, when pre-indexed addressing mode is used.
Patch by Mihail Popa <Mihail.Popa@arm.com>
llvm-svn: 179398
These instructions aren't universally available, but depend on a specific
extension to the normal ARM architecture (rather than, say, v6/v7/...) so a new
feature is appropriate.
This also enables the feature by default on A-class cores which usually have
these extensions, to avoid breaking existing code and act as a sensible
default.
llvm-svn: 179171
This fixes an issue where trying to assemlbe valid ADR instructions would cause
LLVM to hit a failed assertion.
Patch by Keith Walker.
llvm-svn: 176189
The NOP, WFE, WFI, SEV and YIELD instructions are all hints w/
a different immediate value in bits [7,0]. Define a generic HINT
instruction and refactor NOP, WFI, WFI, SEV and YIELD to be
assembly aliases of that.
rdar://11600518
llvm-svn: 158674
We on the linker to resolve calls to the appropriate BL/BLX instruction
to make interworking function correctly. It uses the symbol in the
relocation to do that, so we need to be careful about being too clever.
To enable this for ARM mode, split the BL/BLX fixup kind off from the
unconditional-branch fixups.
rdar://10927209
llvm-svn: 151571
"mov r1, r2, lsl #0" should assemble as "mov r1, r2" even though it's
not strictly legal UAL syntax. It's a common extension and the friendly
thing to do.
rdar://10604663
llvm-svn: 146937
When 'cmp rn #imm' doesn't match due to the immediate not being representable,
but 'cmn rn, #-imm' does match, use the latter in place of the former, as
it's equivalent.
rdar://10552389
llvm-svn: 146567
When the immediate operand of an AND or BIC instruction isn't representable
in the immediate field of the instruction, but the bitwise negation of the
immediate is, assemble the instruction as the inverse operation instead
with the inverted immediate as the operand.
rdar://10550057
llvm-svn: 146283
We don't (yet) have the granularity in the fixups to be specific about which
bitranges are affected. That's a future cleanup, but we're not there yet.
llvm-svn: 144852
Asiri Rathnayake