Current 64-bit SVR4 code seems to have some remnants of Darwin code
in AltiVec argument handing. This had the effect that AltiVec arguments
(or subsequent arguments) were not correctly placed in the parameter area
in some cases.
The correct behaviour with the 64-bit SVR4 ABI is:
- All AltiVec arguments take up space in the parameter area, just like
any other arguments, whether vararg or not.
- They are always 16-byte aligned, skipping a parameter area doubleword
(and the associated GPR, if any), if necessary.
This patch implements the correct behaviour and adds a test case.
(Verified against GCC behaviour via the ABI compat test suite.)
llvm-svn: 211492
When small arguments (structures < 8 bytes or "float") are passed in a
stack slot in the ppc64 SVR4 ABI, they must reside in the least
significant part of that slot. On BE, this means that an offset needs
to be added to the stack address of the parameter, but on LE, the least
significant part of the slot has the same address as the slot itself.
This changes the PowerPC back-end ABI code to only add the small
argument stack slot offset for BE. It also adds test cases to verify
the correct behavior on both BE and LE.
llvm-svn: 211368
During an indirect function call sequence on the 64-bit SVR4 ABI,
generate code must load and then restore the TOC register.
This does not use a regular LOAD instruction since the TOC
register r2 is marked as reserved. Instead, the are two
special instruction patterns:
let RST = 2, DS = 2 in
def LDinto_toc: DSForm_1a<58, 0, (outs), (ins g8rc:$reg),
"ld 2, 8($reg)", IIC_LdStLD,
[(PPCload_toc i64:$reg)]>, isPPC64;
let RST = 2, DS = 10, RA = 1 in
def LDtoc_restore : DSForm_1a<58, 0, (outs), (ins),
"ld 2, 40(1)", IIC_LdStLD,
[(PPCtoc_restore)]>, isPPC64;
Note that these not only restrict the destination of the
load to r2, but they also restrict the *source* of the
load to particular address combinations. The latter is
a problem when we want to support the ELFv2 ABI, since
there the TOC save slot is no longer at 40(1).
This patch replaces those two instructions with a single
instruction pattern that only hard-codes r2 as destination,
but supports generic addresses as source. This will allow
supporting the ELFv2 ABI, and also helps generate more
efficient code for calls to absolute addresses (allowing
simplification of the ppc64-calls.ll test case).
llvm-svn: 211193
As requested by Hal Finkel, this adds back a test for calls to
a known-constant function pointer value, and verifies that the
64-bit SVR4 indirect function call sequence is used.
llvm-svn: 211190
The PowerPC back-end uses BLA to implement calls to functions at
known-constant addresses, which is apparently used for certain
system routines on Darwin.
However, with the 64-bit SVR4 ABI, this is actually incorrect.
An immediate function pointer value on this platform is not
directly usable as a target address for BLA:
- in the ELFv1 ABI, the function pointer value refers to the
*function descriptor*, not the code address
- in the ELFv2 ABI, the function pointer value refers to the
global entry point, but BL(A) would only be correct when
calling the *local* entry point
This bug didn't show up since using immediate function pointer
values is not usually done in the 64-bit SVR4 ABI in the first
place. However, I ran into this issue with a certain use case
of LLVM as JIT, where immediate function pointer values were
uses to implement callbacks from JITted code to helpers in
statically compiled code.
Fixed by simply not using BLA with the 64-bit SVR4 ABI.
llvm-svn: 211174
Rafael opened http://llvm.org/bugs/show_bug.cgi?id=19893 to track non-optimal
code generation for forming a function address that is local to the compile
unit. The existing code was treating both local and non-local functions
identically.
This patch fixes the problem by properly identifying local functions and
generating the proper addis/addi code. I also noticed that Rafael's earlier
changes to correct the surrounding code in PPCISelLowering.cpp were also
needed for fast instruction selection in PPCFastISel.cpp, so this patch
fixes that code as well.
The existing test/CodeGen/PowerPC/func-addr.ll is modified to test the new
code generation. I've added a -O0 run line to test the fast-isel code as
well.
Tested on powerpc64[le]-unknown-linux-gnu with no regressions.
llvm-svn: 211056
This commit adds a weak variant of the cmpxchg operation, as described
in C++11. A cmpxchg instruction with this modifier is permitted to
fail to store, even if the comparison indicated it should.
As a result, cmpxchg instructions must return a flag indicating
success in addition to their original iN value loaded. Thus, for
uniformity *all* cmpxchg instructions now return "{ iN, i1 }". The
second flag is 1 when the store succeeded.
At the DAG level, a new ATOMIC_CMP_SWAP_WITH_SUCCESS node has been
added as the natural representation for the new cmpxchg instructions.
It is a strong cmpxchg.
By default this gets Expanded to the existing ATOMIC_CMP_SWAP during
Legalization, so existing backends should see no change in behaviour.
If they wish to deal with the enhanced node instead, they can call
setOperationAction on it. Beware: as a node with 2 results, it cannot
be selected from TableGen.
Currently, no use is made of the extra information provided in this
patch. Test updates are almost entirely adapting the input IR to the
new scheme.
Summary for out of tree users:
------------------------------
+ Legacy Bitcode files are upgraded during read.
+ Legacy assembly IR files will be invalid.
+ Front-ends must adapt to different type for "cmpxchg".
+ Backends should be unaffected by default.
llvm-svn: 210903
Various masks on shufflevector instructions are recognizable as
specific PowerPC instructions (vector pack, vector merge, etc.).
There is existing code in PPCISelLowering.cpp to recognize the correct
patterns for big endian code. The masks for these instructions are
different for little endian code due to the big-endian numbering
employed by these instructions. This patch adds the recognition code
for little endian.
I've added a new test case test/CodeGen/PowerPC/vec_shuffle_le.ll for
this. The existing recognizer test (vec_shuffle.ll) is unnecessarily
verbose and difficult to read, so I felt it was better to add a new
test rather than modify the old one.
llvm-svn: 210536
The code in PPCTargetLowering::PerformDAGCombine() that handles
unaligned Altivec vector loads generates a lvsl followed by a vperm.
As we've seen in numerous other places, the vperm instruction has a
big-endian bias, and this is fixed for little endian by complementing
the permute control vector and swapping the input operands. In this
case the lvsl is providing the permute control vector. Rather than
generating an lvsl and a complement operation, it is sufficient to
generate an lvsr instruction instead. Thus for LE code generation we
will generate an lvsr rather than an lvsl, and swap the other input
arguments on the vperm.
The existing test/CodeGen/PowerPC/vec_misalign.ll is updated to test
the code generation for PPC64 and PPC64LE, in addition to the existing
PPC32/G5 testing.
llvm-svn: 210493
The existing code in PPCTargetLowering::LowerMUL() for multiplying two
v16i8 values assumes that vector elements are numbered in big-endian
order. For little-endian targets, the vector element numbering is
reversed, but the vmuleub, vmuloub, and vperm instructions still
assume big-endian numbering. To account for this, we must adjust the
permute control vector and reverse the order of the input registers on
the vperm instruction.
The existing test/CodeGen/PowerPC/vec_mul.ll is updated to be executed
on powerpc64 and powerpc64le targets as well as the original powerpc
(32-bit) target.
llvm-svn: 210474
This patch fixes a couple of lowering issues for little endian
PowerPC. The code for lowering BUILD_VECTOR contains a number of
optimizations that are only valid for big endian. For now, we disable
those optimizations for correctness. In the future, we will add
analogous optimizations that are correct for little endian.
When lowering a SHUFFLE_VECTOR to a VPERM operation, we again need to
make the now-familiar transformation of swapping the input operands
and complementing the permute control vector. Correctness of this
transformation is tested by the accompanying test case.
llvm-svn: 210336
Chandler correctly pointed out that I need an LLVM IR test for
r210282, which modified the vperm -> shuffle transform for little
endian PowerPC. This patch provides that test.
llvm-svn: 210297
This seems to match what gcc does for ppc and what every other llvm
backend does.
This is a fixed version of r209638. The difference is to avoid any change
in behavior for functions. The logic for using constant pools for function
addresseses is spread over a few places and we have to keep them in sync.
llvm-svn: 209821
This reverts commit r209638 because it broke self-hosting on ppc64/Linux. (the
Clang-compiled TableGen would segfault because it jumped to an invalid address
from within _ZNK4llvm17ManagedStaticBase21RegisterManagedStaticEPFPvvEPFvS1_E
(which is within the command-line parameter registration process)).
llvm-svn: 209745
In PPCISelLowering.cpp: PPCTargetLowering::LowerBUILD_VECTOR(), there
is an optimization for certain patterns to generate one or two vector
splats followed by a vector add or subtract. This operation is
represented by a VADD_SPLAT in the selection DAG. Prior to this
patch, it was possible for the VADD_SPLAT to be assigned the wrong
data type, causing incorrect code generation. This patch corrects the
problem.
Specifically, the code previously assigned the value type of the
BUILD_VECTOR node to the newly generated VADD_SPLAT node. This is
correct much of the time, but not always. The problem is that the
call to isConstantSplat() may return a SplatBitSize that is not the
same as the number of bits in the original element vector type. The
correct type to assign is a vector type with the same element bit size
as SplatBitSize.
The included test case shows an example of this, where the
BUILD_VECTOR node has a type of v16i8. The vector to be built is {0,
16, 0, 16, 0, 16, 0, 16, 0, 16, 0, 16, 0, 16, 0, 16}. isConstantSplat
detects that we can generate a splat of 16 for type v8i16, which is
the type we must assign to the VADD_SPLAT node. If we do not, we
generate a vspltisb of 8 and a vaddubm, which generates the incorrect
result {16, 16, 16, 16, 16, 16, 16, 16, 16, 16, 16, 16, 16, 16, 16,
16}. The correct code generation is a vspltish of 8 and a vadduhm.
This patch also corrected code generation for
CodeGen/PowerPC/2008-07-10-SplatMiscompile.ll, which had been marked
as an XFAIL, so we can remove the XFAIL from the test case.
llvm-svn: 209662
The SplitIndexingFromLoad changes exposed a latent isel bug in the PowerPC64
backend. We matched an immediate offset with STWX8 even though it only
supports register offset.
The culprit is the complex-pattern predicate, SelectAddrIdx, which decides
that if the offset is not ISD::Constant it must be a register.
Many thanks to Bill Schmidt for testing this.
llvm-svn: 209219
Many old tests using prior schemas still had some brokenness here (both
indirect arrays and arrays with single bogus elements). Fixed those up
so they don't hit the new assertions.
Also reduced nesting in some places, etc.
llvm-svn: 208817
Support for the intrinsics that read from and write to global named registers
is added for r1, r2 and r13 (depending on the subtarget).
llvm-svn: 208509
The counter-loops formation pass needs to know what operations might be
function calls (because they can't appear in counter-based loops). On PPC32,
128-bit shifts might be runtime calls (even though you can't use __int128 on
PPC32, it seems that SROA might form them).
Fixes PR19709.
llvm-svn: 208501
We had been using the known-zero values of the operand of the or to construct
the mask for an rlwimi; this is not quite correct, but fine when the mask is
constant. When the mask is constant, then the known zeros of the operand must
be a superset of the zeros in the mask. However, when the mask is not a
constant, then there might be bits in the operand that are not known to be zero
that, at runtime, might be zero in the mask. Therefore, we check that any bits
not known to be zero *are* known to be one in the mask. Otherwise, we can't
fold the mask with the or and shift.
This was revealed as a miscompile of
MultiSource/Benchmarks/BitBench/drop3/drop3 when I started experimenting with
constant hoisting.
llvm-svn: 206136
We had disabled use of TBAA during CodeGen (even when otherwise using AA)
because the ptrtoint/inttoptr used by CGP for address sinking caused BasicAA to
miss basic type punning that it should catch (and, thus, we'd fail to override
TBAA when we should).
However, when AA is in use during CodeGen, CGP now uses normal GEPs and
bitcasts, instead of ptrtoint/inttoptr, when doing address sinking. As a
result, BasicAA should be able to make us do the right thing in the face of
type-punning, and it seems safe to enable use of TBAA again. self-hosting seems
fine on PPC64/Linux on the P7, with TBAA enabled and -misched=shuffle.
Note: We still don't update TBAA when merging stack slots, although because
BasicAA should now catch all such cases, this is no longer a blocking issue.
Nevertheless, I plan to commit code to deal with this properly in the near
future.
llvm-svn: 206093
The current memory-instruction optimization logic in CGP, which sinks parts of
the address computation that can be adsorbed by the addressing mode, does this
by explicitly converting the relevant part of the address computation into
IR-level integer operations (making use of ptrtoint and inttoptr). For most
targets this is currently not a problem, but for targets wishing to make use of
IR-level aliasing analysis during CodeGen, the use of ptrtoint/inttoptr is a
problem for two reasons:
1. BasicAA becomes less powerful in the face of the ptrtoint/inttoptr
2. In cases where type-punning was used, and BasicAA was used
to override TBAA, BasicAA may no longer do so. (this had forced us to disable
all use of TBAA in CodeGen; something which we can now enable again)
This (use of GEPs instead of ptrtoint/inttoptr) is not currently enabled by
default (except for those targets that use AA during CodeGen), and so aside
from some PowerPC subtargets and SystemZ, there should be no change in
behavior. We may be able to switch completely away from the ptrtoint/inttoptr
sinking on all targets, but further testing is required.
I've doubled-up on a number of existing tests that are sensitive to the
address sinking behavior (including some store-merging tests that are
sensitive to the order of the resulting ADD operations at the SDAG level).
llvm-svn: 206092
gcc inline asm supports specifying "cc" as a clobber of all condition
registers. Add just enough modeling of the full register to make this work.
Fixed PR19326.
llvm-svn: 205630
If we have two unique values for a v2i64 build vector, this will always result
in two vector loads if we expand using shuffles. Only one is necessary.
llvm-svn: 205231
When the loop vectorizer vectorizes code that uses the loop induction variable,
we often end up with IR like this:
%b1 = insertelement <2 x i32> undef, i32 %v, i32 0
%b2 = shufflevector <2 x i32> %b1, <2 x i32> undef, <2 x i32> zeroinitializer
%i = add <2 x i32> %b2, <i32 2, i32 3>
If the add in this example is not legal (as is the case on PPC with VSX), it
will be scalarized, and we'll end up with a number of extract_vector_elt nodes
with the vector shuffle as the input operand, and that vector shuffle is fed by
one or more build_vector nodes. By the time that vector operations are
expanded, visitEXTRACT_VECTOR_ELT will not create new extract_vector_elt by
looking through the vector shuffle (to make sure that no illegal operations are
created), and so the extract_vector_elt -> vector shuffle -> build_vector is
never simplified to an operand of the build vector.
By looking at build_vectors through a shuffle we fix this particular situation,
preventing a vector from being built, only to be deconstructed again (for the
scalarized add) -- an expensive proposition when this all needs to be done via
the stack. We probably want a more comprehensive fix here where we look back
recursively through any shuffles to any build_vectors or scalar_to_vectors,
etc. but that can come later.
llvm-svn: 205179
When expanding EXTRACT_VECTOR_ELT and EXTRACT_SUBVECTOR using
SelectionDAGLegalize::ExpandExtractFromVectorThroughStack, we store the entire
vector and then load the piece we want. This is fine in isolation, but
generating a new store (and corresponding stack slot) for each extraction ends
up producing code of poor quality. When we scalarize a vector operation (using
SelectionDAG::UnrollVectorOp for example) we generate one EXTRACT_VECTOR_ELT
for each element in the vector. This used to generate one stored copy of the
vector for each element in the vector. Now we search the uses of the vector for
a suitable store before generating a new one, which results in much more
efficient scalarization code.
llvm-svn: 205153
sitofp from v2i32 to v2f64 ends up generating a SIGN_EXTEND_INREG v2i64 node
(and similarly for v2i16 and v2i8). Even though there are no sign-extension (or
algebraic shifts) for v2i64 types, we can handle v2i32 sign extensions by
converting two and from v2i64. The small trick necessary here is to shift the
i32 elements into the right lanes before the i32 -> f64 step. This is because
of the big Endian nature of the system, we need the i32 portion in the high
word of the i64 elements.
For v2i16 and v2i8 we can do the same, but we first use the default Altivec
shift-based expansion from v2i16 or v2i8 to v2i32 (by casting to v4i32) and
then apply the above procedure.
llvm-svn: 205146
v2i64 is a legal type under VSX, however we don't have native vector
comparisons. We can handle eq/ne by casting it to an Altivec type, but
everything else must be expanded.
llvm-svn: 205106
We had stored both f64 values and v2f64, etc. values in the VSX registers. This
worked, but was suboptimal because we would always spill 16-byte values even
through we almost always had scalar 8-byte values. This resulted in an
increase in stack-size use, extra memory bandwidth, etc. To fix this, I've
added 64-bit subregisters of the Altivec registers, and combined those with the
existing scalar floating-point registers to form a class of VSX scalar
floating-point registers. The ABI code has also been enhanced to use this
register class and some other necessary improvements have been made.
llvm-svn: 205075
v2[fi]64 values need to be explicitly passed in VSX registers. This is because
the code in TRI that finds the minimal register class given a register and a
value type will assert if given an Altivec register and a non-Altivec type.
llvm-svn: 205041
As explained in r204976, because of how the allocation of VSX registers
interacts with the call-lowering code, we sometimes end up generating self VSX
copies. Specifically, things like this:
%VSL2<def> = COPY %F2, %VSL2<imp-use,kill>
(where %F2 is really a sub-register of %VSL2, and so this copy is a nop)
This adds a small cleanup pass to remove these prior to post-RA scheduling.
llvm-svn: 204980
First, v2f64 vector extract had not been declared legal (and so the existing
patterns were not being used). Second, the patterns for that, and for
scalar_to_vector, should really be a regclass copy, not a subregister
operation, because the VSX registers directly hold both the vector and scalar data.
llvm-svn: 204971
These operations need to be expanded during legalization so that isel does not
crash. In theory, we might be able to custom lower some of these. That,
however, would need to be follow-up work.
llvm-svn: 204963
These instructions have access to the complete VSX register file. In addition,
they "swap" the order of the elements so that element 0 (the scalar part) comes
first in memory and element 1 follows at a higher address.
llvm-svn: 204838
v2i64 needs to be a legal VSX type because it is the SetCC result type from
v2f64 comparisons. We need to expand all non-arithmetic v2i64 operations.
This fixes the lowering for v2f64 VSELECT.
llvm-svn: 204828
With VSX there is a real vector select instruction, and so we should use it.
Note that VSELECT will still scalarize for v2f64 because the corresponding
SetCC result type (v2i64) is not currently a legal type.
llvm-svn: 204801
The VSX instruction set has two types of FMA instructions: A-type (where the
addend is taken from the output register) and M-type (where one of the product
operands is taken from the output register). This adds a small pass that runs
just after MI scheduling (and, thus, just before register allocation) that
mutates A-type instructions (that are created during isel) into M-type
instructions when:
1. This will eliminate an otherwise-necessary copy of the addend
2. One of the product operands is killed by the instruction
The "right" moment to make this decision is in between scheduling and register
allocation, because only there do we know whether or not one of the product
operands is killed by any particular instruction. Unfortunately, this also
makes the implementation somewhat complicated, because the MIs are not in SSA
form and we need to preserve the LiveIntervals analysis.
As a simple example, if we have:
%vreg5<def> = COPY %vreg9; VSLRC:%vreg5,%vreg9
%vreg5<def,tied1> = XSMADDADP %vreg5<tied0>, %vreg17, %vreg16,
%RM<imp-use>; VSLRC:%vreg5,%vreg17,%vreg16
...
%vreg9<def,tied1> = XSMADDADP %vreg9<tied0>, %vreg17, %vreg19,
%RM<imp-use>; VSLRC:%vreg9,%vreg17,%vreg19
...
We can eliminate the copy by changing from the A-type to the
M-type instruction. This means:
%vreg5<def,tied1> = XSMADDADP %vreg5<tied0>, %vreg17, %vreg16,
%RM<imp-use>; VSLRC:%vreg5,%vreg17,%vreg16
is replaced by:
%vreg16<def,tied1> = XSMADDMDP %vreg16<tied0>, %vreg18, %vreg9,
%RM<imp-use>; VSLRC:%vreg16,%vreg18,%vreg9
and we remove: %vreg5<def> = COPY %vreg9; VSLRC:%vreg5,%vreg9
llvm-svn: 204768
When VSX is available, these instructions should be used in preference to the
older variants that only have access to the scalar floating-point registers.
llvm-svn: 204559
When converting a signed 32-bit integer to double-precision floating point on
hardware without a lfiwax instruction, we have to instead use a lfd followed
by fcfid. We were erroneously offsetting the address by 4 bytes in
preparation for either a lfiwax or lfiwzx when generating the lfd. This fixes
that silly error.
This was not caught in the test suite since the conversion tests were run with
-mcpu=pwr7, which implies availability of lfiwax. I've added another test
case for older hardware that checks the code we expect in the absence of
lfiwax and other flavors of fcfid. There are fewer tests in this test case
because we punt to DAG selection in more cases on older hardware. (We must
generate complex fiddly sequences in those cases, and there is marginal
benefit in duplicating that logic in fast-isel.)
llvm-svn: 204155
Commit r181723 introduced code to avoid placing initialized variables
needing relocations into the .rodata section, which avoid copy relocs
that do not work as expected on ppc64 function references.
The same treatment is also needed for *named* .rodata.XXX sections.
This patch changes PPC64LinuxTargetObjectFile::SelectSectionForGlobal
to modify "Kind" *before* calling the default SelectSectionForGlobal
routine, instead of first calling the default routine and then just
checking for the (main) .rodata section afterwards.
llvm-svn: 203921
These linkages were introduced some time ago, but it was never very
clear what exactly their semantics were or what they should be used
for. Some investigation found these uses:
* utf-16 strings in clang.
* non-unnamed_addr strings produced by the sanitizers.
It turns out they were just working around a more fundamental problem.
For some sections a MachO linker needs a symbol in order to split the
section into atoms, and llvm had no idea that was the case. I fixed
that in r201700 and it is now safe to use the private linkage. When
the object ends up in a section that requires symbols, llvm will use a
'l' prefix instead of a 'L' prefix and things just work.
With that, these linkages were already dead, but there was a potential
future user in the objc metadata information. I am still looking at
CGObjcMac.cpp, but at this point I am convinced that linker_private
and linker_private_weak are not what they need.
The objc uses are currently split in
* Regular symbols (no '\01' prefix). LLVM already directly provides
whatever semantics they need.
* Uses of a private name (start with "\01L" or "\01l") and private
linkage. We can drop the "\01L" and "\01l" prefixes as soon as llvm
agrees with clang on L being ok or not for a given section. I have two
patches in code review for this.
* Uses of private name and weak linkage.
The last case is the one that one could think would fit one of these
linkages. That is not the case. The semantics are
* the linker will merge these symbol by *name*.
* the linker will hide them in the final DSO.
Given that the merging is done by name, any of the private (or
internal) linkages would be a bad match. They allow llvm to rename the
symbols, and that is really not what we want. From the llvm point of
view, these objects should really be (linkonce|weak)(_odr)?.
For now, just keeping the "\01l" prefix is probably the best for these
symbols. If we one day want to have a more direct support in llvm,
IMHO what we should add is not a linkage, it is just a hidden_symbol
attribute. It would be applicable to multiple linkages. For example,
on weak it would produce the current behavior we have for objc
metadata. On internal, it would be equivalent to private (and we
should then remove private).
llvm-svn: 203866
VSX is an ISA extension supported on the POWER7 and later cores that enhances
floating-point vector and scalar capabilities. Among other things, this adds
<2 x double> support and generally helps to reduce register pressure.
The interesting part of this ISA feature is the register configuration: there
are 64 new 128-bit vector registers, the 32 of which are super-registers of the
existing 32 scalar floating-point registers, and the second 32 of which overlap
with the 32 Altivec vector registers. This makes things like vector insertion
and extraction tricky: this can be free but only if we force a restriction to
the right register subclass when needed. A new "minipass" PPCVSXCopy takes care
of this (although it could do a more-optimal job of it; see the comment about
unnecessary copies below).
Please note that, currently, VSX is not enabled by default when targeting
anything because it is not yet ready for that. The assembler and disassembler
are fully implemented and tested. However:
- CodeGen support causes miscompiles; test-suite runtime failures:
MultiSource/Benchmarks/FreeBench/distray/distray
MultiSource/Benchmarks/McCat/08-main/main
MultiSource/Benchmarks/Olden/voronoi/voronoi
MultiSource/Benchmarks/mafft/pairlocalalign
MultiSource/Benchmarks/tramp3d-v4/tramp3d-v4
SingleSource/Benchmarks/CoyoteBench/almabench
SingleSource/Benchmarks/Misc/matmul_f64_4x4
- The lowering currently falls back to using Altivec instructions far more
than it should. Worse, there are some things that are scalarized through the
stack that shouldn't be.
- A lot of unnecessary copies make it past the optimizers, and this needs to
be fixed.
- Many more regression tests are needed.
Normally, I'd fix these things prior to committing, but there are some
students and other contributors who would like to work this, and so it makes
sense to move this development process upstream where it can be subject to the
regular code-review procedures.
llvm-svn: 203768
The syntax for "cmpxchg" should now look something like:
cmpxchg i32* %addr, i32 42, i32 3 acquire monotonic
where the second ordering argument gives the required semantics in the case
that no exchange takes place. It should be no stronger than the first ordering
constraint and cannot be either "release" or "acq_rel" (since no store will
have taken place).
rdar://problem/15996804
llvm-svn: 203559
When copying an i1 value into a GPR for a vaarg call, we need to explicitly
zero-extend the i1 value (otherwise an invalid CRBIT -> GPR copy will be
generated).
llvm-svn: 203041
On cores without fpcvt support, we cannot promote int_to_fp i1 operations,
because there is nothing to promote them to. The most straightforward
implementation of this uses a select to choose between the two possible
resulting floating-point values (and that's what is done here).
llvm-svn: 203015
Now that the PowerPC backend can track individual CR bits as first-class
registers, we should also have a way of allocating them for inline asm
statements. Because these registers are only one bit, if an output variable is
implicitly cast to a larger integer size, we'll get an any_extend to that
larger type (this is part of the existing target-independent logic). As a
result, regardless of the size of the output type, only the first bit is
meaningful.
The constraint identifier "wc" has been chosen for this purpose. Although gcc
does not currently support allocating individual CR bits, this identifier
choice has been coordinated with the gcc PowerPC team, and will be marked as
reserved for this purpose in the gcc constraints.md file.
llvm-svn: 202657
This generalizes the code to eliminate extra truncs/exts around i1 bit
operations to also do the same on PPC64 for i32 bit operations. This eliminates
a fairly prevalent code wart:
int foo(int a) {
return a == 5 ? 7 : 8;
}
On PPC64, because of the extension implied by the ABI, this would generate:
cmplwi 0, 3, 5
li 12, 8
li 4, 7
isel 3, 4, 12, 2
rldicl 3, 3, 0, 32
blr
where the 'rldicl 3, 3, 0, 32', the extension, is completely unnecessary. At
least for the single-BB case (which is all that the DAG combine mechanism can
handle), this unnecessary extension is no longer generated.
llvm-svn: 202600
The PPC isel instruction can fold 0 into the first operand (thus eliminating
the need to materialize a zero-containing register when the 'true' result of
the isel is 0). When the isel is fed by a bit register operation that we can
invert, do so as part of the bit-register-operation peephole routine.
llvm-svn: 202469
This change enables tracking i1 values in the PowerPC backend using the
condition register bits. These bits can be treated on PowerPC as separate
registers; individual bit operations (and, or, xor, etc.) are supported.
Tracking booleans in CR bits has several advantages:
- Reduction in register pressure (because we no longer need GPRs to store
boolean values).
- Logical operations on booleans can be handled more efficiently; we used to
have to move all results from comparisons into GPRs, perform promoted
logical operations in GPRs, and then move the result back into condition
register bits to be used by conditional branches. This can be very
inefficient, because the throughput of these CR <-> GPR moves have high
latency and low throughput (especially when other associated instructions
are accounted for).
- On the POWER7 and similar cores, we can increase total throughput by using
the CR bits. CR bit operations have a dedicated functional unit.
Most of this is more-or-less mechanical: Adjustments were needed in the
calling-convention code, support was added for spilling/restoring individual
condition-register bits, and conditional branch instruction definitions taking
specific CR bits were added (plus patterns and code for generating bit-level
operations).
This is enabled by default when running at -O2 and higher. For -O0 and -O1,
where the ability to debug is more important, this feature is disabled by
default. Individual CR bits do not have assigned DWARF register numbers,
and storing values in CR bits makes them invisible to the debugger.
It is critical, however, that we don't move i1 values that have been promoted
to larger values (such as those passed as function arguments) into bit
registers only to quickly turn around and move the values back into GPRs (such
as happens when values are returned by functions). A pair of target-specific
DAG combines are added to remove the trunc/extends in:
trunc(binary-ops(binary-ops(zext(x), zext(y)), ...)
and:
zext(binary-ops(binary-ops(trunc(x), trunc(y)), ...)
In short, we only want to use CR bits where some of the i1 values come from
comparisons or are used by conditional branches or selects. To put it another
way, if we can do the entire i1 computation in GPRs, then we probably should
(on the POWER7, the GPR-operation throughput is higher, and for all cores, the
CR <-> GPR moves are expensive).
POWER7 test-suite performance results (from 10 runs in each configuration):
SingleSource/Benchmarks/Misc/mandel-2: 35% speedup
MultiSource/Benchmarks/Prolangs-C++/city/city: 21% speedup
MultiSource/Benchmarks/MiBench/automotive-susan: 23% speedup
SingleSource/Benchmarks/CoyoteBench/huffbench: 13% speedup
SingleSource/Benchmarks/Misc-C++/Large/sphereflake: 13% speedup
SingleSource/Benchmarks/Misc-C++/mandel-text: 10% speedup
SingleSource/Benchmarks/Misc-C++-EH/spirit: 10% slowdown
MultiSource/Applications/lemon/lemon: 8% slowdown
llvm-svn: 202451
We need to abort the formation of counter-register-based loops where there are
128-bit integer operations that might become function calls.
llvm-svn: 202192
r201608 made llvm corretly handle private globals with MachO. r201622 fixed
a bug in it and r201624 and r201625 were changes for using private linkage,
assuming that llvm would do the right thing.
They all got reverted because r201608 introduced a crash in LTO. This patch
includes a fix for that. The issue was that TargetLoweringObjectFile now has
to be initialized before we can mangle names of private globals. This is
trivially true during the normal codegen pipeline (the asm printer does it),
but LTO has to do it manually.
llvm-svn: 201700
The IR
@foo = private constant i32 42
is valid, but before this patch we would produce an invalid MachO from it. It
was invalid because it would use an L label in a section where the liker needs
the labels in order to atomize it.
One way of fixing it would be to just reject this IR in the backend, but that
would not be very front end friendly.
What this patch does is use an 'l' prefix in sections that we know the linker
requires symbols for atomizing them. This allows frontends to just use
private and not worry about which sections they go to or how the linker handles
them.
One small issue with this strategy is that now a symbol name depends on the
section, which is not available before codegen. This is not a problem in
practice. The reason is that it only happens with private linkage, which will
be ignored by the non codegen users (llvm-nm and llvm-ar).
llvm-svn: 201608
Summary:
AsmPrinter::EmitInlineAsm() will no longer use the EmitRawText() call for
targets with mature MC support. Such targets will always parse the inline
assembly (even when emitting assembly). Targets without mature MC support
continue to use EmitRawText() for assembly output.
The hasRawTextSupport() check in AsmPrinter::EmitInlineAsm() has been replaced
with MCAsmInfo::UseIntegratedAs which when true, causes the integrated assembler
to parse inline assembly (even when emitting assembly output). UseIntegratedAs
is set to true for targets that consider any failure to parse valid assembly
to be a bug. Target specific subclasses generally enable the integrated
assembler in their constructor. The default value can be overridden with
-no-integrated-as.
All tests that rely on inline assembly supporting invalid assembly (for example,
those that use mnemonics such as 'foo' or 'hello world') have been updated to
disable the integrated assembler.
Changes since review (and last commit attempt):
- Fixed test failures that were missed due to configuration of local build.
(fixes crash.ll and a couple others).
- Fixed tests that happened to pass because the local build was on X86
(should fix 2007-12-17-InvokeAsm.ll)
- mature-mc-support.ll's should no longer require all targets to be compiled.
(should fix ARM and PPC buildbots)
- Object output (-filetype=obj and similar) now forces the integrated assembler
to be enabled regardless of default setting or -no-integrated-as.
(should fix SystemZ buildbots)
Reviewers: rafael
Reviewed By: rafael
CC: llvm-commits
Differential Revision: http://llvm-reviews.chandlerc.com/D2686
llvm-svn: 201333
Summary:
AsmPrinter::EmitInlineAsm() will no longer use the EmitRawText() call for targets with mature MC support. Such targets will always parse the inline assembly (even when emitting assembly). Targets without mature MC support continue to use EmitRawText() for assembly output.
The hasRawTextSupport() check in AsmPrinter::EmitInlineAsm() has been replaced with MCAsmInfo::UseIntegratedAs which when true, causes the integrated assembler to parse inline assembly (even when emitting assembly output). UseIntegratedAs is set to true for targets that consider any failure to parse valid assembly to be a bug. Target specific subclasses generally enable the integrated assembler in their constructor. The default value can be overridden with -no-integrated-as.
All tests that rely on inline assembly supporting invalid assembly (for example, those that use mnemonics such as 'foo' or 'hello world') have been updated to disable the integrated assembler.
Reviewers: rafael
Reviewed By: rafael
CC: llvm-commits
Differential Revision: http://llvm-reviews.chandlerc.com/D2686
llvm-svn: 201237
A bunch of test cases needed to be cleaned up for this, many my fault -
when implementid imported modules I updated test cases by simply
duplicating the prior metadata field - which wasn't always the empty
metadata entry.
llvm-svn: 200731
GPRC_NOR0 is not a subclass of GPRC (because it also contains the ZERO pseudo
register). As a result, we also need to check for it in the spilling code.
llvm-svn: 200288
I disabled the use of TBAA in CodeGen in r200093. This adds a test case that
demonstrates the problems with inttoptr and TBAA in CodeGen (and, specifically,
the problem that causes LLVM to miscompile itself in Release mode). This test
will currently fail if -use-tbaa-in-sched-mi is enabled.
llvm-svn: 200097
For PPC64 SVR (and Darwin), the stores that take byval aggregate parameters
from registers into the stack frame had MachinePointerInfo objects with
incorrect offsets. These offsets are relative to the object itself, not to the
stack frame base.
This fixes self hosting on PPC64 when compiling with -enable-aa-sched-mi.
llvm-svn: 199763
This is a base implementation of the powerpc-apple-darwin asm parser dialect.
* Enables infrastructure (essentially isDarwin()) and fixes up the parsing of asm directives to separate out ELF and MachO/Darwin additions.
* Enables parsing of {r,f,v}XX as register identifiers.
* Enables parsing of lo16() hi16() and ha16() as modifiers.
The changes to the test case are from David Fang (fangism).
llvm-svn: 197324
Aside from a few minor latency corrections, the major change here is a new
hazard recognizer which focuses on better dispatch-group formation on the
POWER7. As with the PPC970's hazard recognizer, the most important thing it
does is avoid load-after-store hazards within the same dispatch group. It uses
the POWER7's special dispatch-group-terminating nop instruction (instead of
inserting multiple regular nop instructions). This new hazard recognizer makes
use of the scheduling dependency graph itself, built using AA information, to
robustly detect the possibility of load-after-store hazards.
significant test-suite performance changes (the error bars are 99.5% confidence
intervals based on 5 test-suite runs both with and without the change --
speedups are negative):
speedups:
MultiSource/Benchmarks/FreeBench/pcompress2/pcompress2
-0.55171% +/- 0.333168%
MultiSource/Benchmarks/TSVC/CrossingThresholds-dbl/CrossingThresholds-dbl
-17.5576% +/- 14.598%
MultiSource/Benchmarks/TSVC/Reductions-dbl/Reductions-dbl
-29.5708% +/- 7.09058%
MultiSource/Benchmarks/TSVC/Reductions-flt/Reductions-flt
-34.9471% +/- 11.4391%
SingleSource/Benchmarks/BenchmarkGame/puzzle
-25.1347% +/- 11.0104%
SingleSource/Benchmarks/Misc/flops-8
-17.7297% +/- 9.79061%
SingleSource/Benchmarks/Shootout-C++/ary3
-35.5018% +/- 23.9458%
SingleSource/Regression/C/uint64_to_float
-56.3165% +/- 25.4234%
SingleSource/UnitTests/Vectorizer/gcc-loops
-18.5309% +/- 6.8496%
regressions:
MultiSource/Benchmarks/ASCI_Purple/SMG2000/smg2000
18.351% +/- 12.156%
SingleSource/Benchmarks/Shootout-C++/methcall
27.3086% +/- 14.4733%
llvm-svn: 197099
For one predicate to subsume another, they must both check the same condition
register. Failure to check this prerequisite was causing miscompiles.
Fixes PR18003.
llvm-svn: 197089
Convert this test to FileCheck, and improve it to check for the instructions it
is trying to exclude instead of checking for register use (especially because
grepping for r1 can be thrown off, for example, by a use of r12).
llvm-svn: 195979
Some of these tests did not specify a cpu but were also sensitive to
instruction scheduling and/or register assignment choices. A few others
similarly-sensitive tests specified a cpu (often the POWER7), and while the P7
currently uses the default model for PPC64, this will soon change. For those
tests which should not really be cpu-dependent anyway, the cpu is set to the
generic 'ppc64'.
llvm-svn: 195977
We are going to drop debug info without a version number or with a different
version number, to make sure we don't crash when we see bitcode files with
different debug info metadata format.
llvm-svn: 195504
The instruction definitions incorrectly specified that popcntd and popcntw have
record forms; they do not. This mistake was causing invalid code generation.
llvm-svn: 195272
Masking operations (where only some number of the low bits are being kept) are
selected to rldicl(x, 0, mb). If x is a logical right shift (which would become
rldicl(y, 64-n, n)), we might be able to fold the two instructions together:
rldicl(rldicl(x, 64-n, n), 0, mb) -> rldicl(x, 64-n, mb) for n <= mb
The right shift is really a left rotate followed by a mask, and if the explicit
mask is a more-restrictive sub-mask of the mask implied by the shift, only one
rldicl is needed.
llvm-svn: 195185
Stop folding constant adds into GEP when the type size doesn't match.
Otherwise, the adds' operands are effectively being promoted, changing the
conditions of an overflow. Results are different when:
sext(a) + sext(b) != sext(a + b)
Problem originally found on x86-64, but also fixed issues with ARM and PPC,
which used similar code.
<rdar://problem/15292280>
Patch by Duncan Exon Smith!
llvm-svn: 194840
In ELF and COFF an alias is just another offset in a section. There is no way
to represent an alias to something in another file.
In MachO, the spec has the N_INDR type which should allow for exactly that, but
is not currently implemented. Given that it is specified but not implemented,
we error in codegen to avoid miscompiling but don't reject aliases to
declarations in the verifier to leave the option open of implementing it.
In the past we have used alias to declarations as a way of implementing
weakref, which is why it exists in some old tests which this patch updates.
llvm-svn: 194705
On non-Darwin PPC systems, we currently strip off the register name prefix
prior to instruction printing. So instead of something like this:
mr r3, r4
we print this:
mr 3, 4
The first form is the default on Darwin, and is understood by binutils, but not
yet understood by our integrated assembler. Once our integrated-as understands
full register names as well, this temporary option will be replaced by tying
this functionality to the verbose-asm option. The numeric-only form is
compatible with legacy assemblers and tools, and is also gcc's default on most
PPC systems. On the other hand, it is harder to read, and there are some
analysis tools that expect full register names.
llvm-svn: 194384
Ulrich Weigand