The benchmarking summarized in
http://lists.llvm.org/pipermail/llvm-dev/2017-May/113525.html showed
this is beneficial for a wide range of cores.
As is to be expected, quite a few small adaptations are needed to the
regressions tests, as the difference in scheduling results in:
- Quite a few small instruction schedule differences.
- A few changes in register allocation decisions caused by different
instruction schedules.
- A few changes in IfConversion decisions, due to a difference in
instruction schedule and/or the estimated cost of a branch mispredict.
llvm-svn: 306514
Essentially the same as the GEP change in r230786.
A similar migration script can be used to update test cases, though a few more
test case improvements/changes were required this time around: (r229269-r229278)
import fileinput
import sys
import re
pat = re.compile(r"((?:=|:|^)\s*load (?:atomic )?(?:volatile )?(.*?))(| addrspace\(\d+\) *)\*($| *(?:%|@|null|undef|blockaddress|getelementptr|addrspacecast|bitcast|inttoptr|\[\[[a-zA-Z]|\{\{).*$)")
for line in sys.stdin:
sys.stdout.write(re.sub(pat, r"\1, \2\3*\4", line))
Reviewers: rafael, dexonsmith, grosser
Differential Revision: http://reviews.llvm.org/D7649
llvm-svn: 230794
This changes the tests that were targeting ARM EABI to explicitly specify the
environment rather than relying on the default. This breaks with the new
Windows on ARM support when running the tests on Windows where the default
environment is no longer EABI.
Take the opportunity to avoid a pointless redirect (helps when trying to debug
with providing a command line invocation which can be copy and pasted) and
removing a few greps in favour of FileCheck.
llvm-svn: 205541
There was an extremely confusing proliferation of LLVM intrinsics to implement
the vacge & vacgt instructions. This combines them all into two polymorphic
intrinsics, shared across both backends.
llvm-svn: 200768
This update was done with the following bash script:
find test/CodeGen -name "*.ll" | \
while read NAME; do
echo "$NAME"
if ! grep -q "^; *RUN: *llc.*debug" $NAME; then
TEMP=`mktemp -t temp`
cp $NAME $TEMP
sed -n "s/^define [^@]*@\([A-Za-z0-9_]*\)(.*$/\1/p" < $NAME | \
while read FUNC; do
sed -i '' "s/;\(.*\)\([A-Za-z0-9_-]*\):\( *\)$FUNC: *\$/;\1\2-LABEL:\3$FUNC:/g" $TEMP
done
sed -i '' "s/;\(.*\)-LABEL-LABEL:/;\1-LABEL:/" $TEMP
sed -i '' "s/;\(.*\)-NEXT-LABEL:/;\1-NEXT:/" $TEMP
sed -i '' "s/;\(.*\)-NOT-LABEL:/;\1-NOT:/" $TEMP
sed -i '' "s/;\(.*\)-DAG-LABEL:/;\1-DAG:/" $TEMP
mv $TEMP $NAME
fi
done
llvm-svn: 186280
DAG. Disable using "-disable-sched-cycles".
For ARM, this enables a framework for modeling the cpu pipeline and
counting stalls. It also activates several heuristics to drive
scheduling based on the model. Scheduling is inherently imprecise at
this stage, and until spilling is improved it may defeat attempts to
schedule. However, this framework provides greater control over
tuning codegen.
Although the flag is not target-specific, it should have very little
affect on the default scheduler used by x86. The only two changes that
affect x86 are:
- scheduling a high-latency operation bumps the current cycle so independent
operations can have their latency covered. i.e. two independent 4
cycle operations can produce results in 4 cycles, not 8 cycles.
- Two operations with equal register pressure impact and no
latency-based stalls on their uses will be prioritized by depth before height
(height is irrelevant if no stalls occur in the schedule below this point).
llvm-svn: 123971
callee-saved registers at the end of the lists. Also prefer to avoid using
the low registers that are in register subclasses required by certain
instructions, so that those registers will more likely be available when needed.
This change makes a huge improvement in spilling in some cases. Thanks to
Jakob for helping me realize the problem.
Most of this patch is fixing the testsuite. There are quite a few places
where we're checking for specific registers. I changed those to wildcards
in places where that doesn't weaken the tests. The spill-q.ll and
thumb2-spill-q.ll tests stopped spilling with this change, so I added a bunch
of live values to force spills on those tests.
llvm-svn: 116055
The trouble arises when the result of a vector cmp + sext is then and'ed with all ones. Instcombine will turn it into a vector cmp + zext, dag combiner will miss turning it into a vsetcc and hell breaks loose after that.
Teach dag combine to turn a vector cpm + zest into a vsetcc + and 1. This fixes rdar://7923010.
llvm-svn: 104094
Kristof Beyls