Currently we have a number of tests that fail with -verify-machineinstrs.
To detect this cases earlier we add the option to the testcases with the
exception of tests that will currently fail with this option. PR 27456 keeps
track of this failures.
No code review, as discussed with Hal Finkel.
llvm-svn: 277624
Essentially the same as the GEP change in r230786.
A similar migration script can be used to update test cases, though a few more
test case improvements/changes were required this time around: (r229269-r229278)
import fileinput
import sys
import re
pat = re.compile(r"((?:=|:|^)\s*load (?:atomic )?(?:volatile )?(.*?))(| addrspace\(\d+\) *)\*($| *(?:%|@|null|undef|blockaddress|getelementptr|addrspacecast|bitcast|inttoptr|\[\[[a-zA-Z]|\{\{).*$)")
for line in sys.stdin:
sys.stdout.write(re.sub(pat, r"\1, \2\3*\4", line))
Reviewers: rafael, dexonsmith, grosser
Differential Revision: http://reviews.llvm.org/D7649
llvm-svn: 230794
This patch addresses the inherent big-endian bias in the lxvd2x,
lxvw4x, stxvd2x, and stxvw4x instructions. These instructions load
vector elements into registers left-to-right (with the first element
loaded into the high-order bits of the register), regardless of the
endian setting of the processor. However, these are the only
vector memory instructions that permit unaligned storage accesses, so
we want to use them for little-endian.
To make this work, a lxvd2x or lxvw4x is replaced with an lxvd2x
followed by an xxswapd, which swaps the doublewords. This works for
lxvw4x as well as lxvd2x, because for lxvw4x on an LE system the
vector elements are in LE order (right-to-left) within each
doubleword. (Thus after lxvw2x of a <4 x float> the elements will
appear as 1, 0, 3, 2. Following the swap, they will appear as 3, 2,
0, 1, as desired.) For stores, an stxvd2x or stxvw4x is replaced
with an stxvd2x preceded by an xxswapd.
Introduction of extra swap instructions provides correctness, but
obviously is not ideal from a performance perspective. Future patches
will address this with optimizations to remove most of the introduced
swaps, which have proven effective in other implementations.
The introduction of the swaps is performed during lowering of LOAD,
STORE, INTRINSIC_W_CHAIN, and INTRINSIC_VOID operations. The latter
are used to translate intrinsics that specify the VSX loads and stores
directly into equivalent sequences for little endian. Thus code that
uses vec_vsx_ld and vec_vsx_st does not have to be modified to be
ported from BE to LE.
We introduce new PPCISD opcodes for LXVD2X, STXVD2X, and XXSWAPD for
use during this lowering step. In PPCInstrVSX.td, we add new SDType
and SDNode definitions for these (PPClxvd2x, PPCstxvd2x, PPCxxswapd).
These are recognized during instruction selection and mapped to the
correct instructions.
Several tests that were written to use -mcpu=pwr7 or pwr8 are modified
to disable VSX on LE variants because code generation changes with
this and subsequent patches in this set. I chose to include all of
these in the first patch than try to rigorously sort out which tests
were broken by one or another of the patches. Sorry about that.
The new test vsx-ldst-builtin-le.ll, and the changes to vsx-ldst.ll,
are disabled until LE support is enabled because of breakages that
occur as noted in those tests. They are re-enabled in patch 4/4.
llvm-svn: 223783
The PowerPC 128-bit long double data type (ppcf128 in LLVM) is in fact a
pair of two doubles, where one is considered the "high" or
more-significant part, and the other is considered the "low" or
less-significant part. When a ppcf128 value is stored in memory or a
register pair, the high part always comes first, i.e. at the lower
memory address or in the lower-numbered register, and the low part
always comes second. This is true both on big-endian and little-endian
PowerPC systems. (Similar to how with a complex number, the real part
always comes first and the imaginary part second, no matter the byte
order of the system.)
This was implemented incorrectly for little-endian systems in LLVM.
This commit fixes three related issues:
- When printing an immediate ppcf128 constant to assembler output
in emitGlobalConstantFP, emit the high part first on both big-
and little-endian systems.
- When lowering a ppcf128 type to a pair of f64 types in SelectionDAG
(which is used e.g. when generating code to load an argument into a
register pair), use correct low/high part ordering on little-endian
systems.
- In a related issue, because lowering ppcf128 into a pair of f64 must
operate differently from lowering an int128 into a pair of i64,
bitcasts between ppcf128 and int128 must not be optimized away by the
DAG combiner on little-endian systems, but must effect a word-swap.
Reviewed by Hal Finkel.
llvm-svn: 212274