Presently, CodeGenPrepare deletes all nearly empty (only phi and branch)
basic blocks. This pass can delete loop preheaders which frequently creates
critical edges. A preheader can be a convenient place to spill registers to
the stack. If the entrance to a loop body is a critical edge, then spills
may occur in the loop body rather than immediately before it. This patch
protects loop preheaders from deletion in CodeGenPrepare even if they are
nearly empty.
Since the patch alters the CFG, it affects a large number of test cases.
In most cases, the changes are merely cosmetic (basic blocks have different
names or instruction orders change slightly). I am somewhat concerned about
the test/CodeGen/Mips/brdelayslot.ll test case. If the loop preheader is not
deleted, then the MIPS backend does not take advantage of a branch delay
slot. Consequently, I would like some close review by a MIPS expert.
The patch also partially subsumes D16893 from George Burgess IV. George
correctly notes that CodeGenPrepare does not actually preserve the dominator
tree. I think the dominator tree was usually not valid when CodeGenPrepare
ran, but I am using LoopInfo to mark preheaders, so the dominator tree is
now always valid before CodeGenPrepare.
Author: Tom Jablin (tjablin)
Reviewers: hfinkel george.burgess.iv vkalintiris dsanders kbarton cycheng
http://reviews.llvm.org/D16984
llvm-svn: 265397
Now that `Metadata` is typeless, reflect that in the assembly. These
are the matching assembly changes for the metadata/value split in
r223802.
- Only use the `metadata` type when referencing metadata from a call
intrinsic -- i.e., only when it's used as a `Value`.
- Stop pretending that `ValueAsMetadata` is wrapped in an `MDNode`
when referencing it from call intrinsics.
So, assembly like this:
define @foo(i32 %v) {
call void @llvm.foo(metadata !{i32 %v}, metadata !0)
call void @llvm.foo(metadata !{i32 7}, metadata !0)
call void @llvm.foo(metadata !1, metadata !0)
call void @llvm.foo(metadata !3, metadata !0)
call void @llvm.foo(metadata !{metadata !3}, metadata !0)
ret void, !bar !2
}
!0 = metadata !{metadata !2}
!1 = metadata !{i32* @global}
!2 = metadata !{metadata !3}
!3 = metadata !{}
turns into this:
define @foo(i32 %v) {
call void @llvm.foo(metadata i32 %v, metadata !0)
call void @llvm.foo(metadata i32 7, metadata !0)
call void @llvm.foo(metadata i32* @global, metadata !0)
call void @llvm.foo(metadata !3, metadata !0)
call void @llvm.foo(metadata !{!3}, metadata !0)
ret void, !bar !2
}
!0 = !{!2}
!1 = !{i32* @global}
!2 = !{!3}
!3 = !{}
I wrote an upgrade script that handled almost all of the tests in llvm
and many of the tests in cfe (even handling many `CHECK` lines). I've
attached it (or will attach it in a moment if you're speedy) to PR21532
to help everyone update their out-of-tree testcases.
This is part of PR21532.
llvm-svn: 224257
Machine Sink uses loop depth information to select between successors BBs to
sink machine instructions into, where BBs within smaller loop depths are
preferable. This patch adds support for choosing between successors by using
profile information from BlockFrequencyInfo instead, whenever the information
is available.
Tested it under SPEC2006 train (average of 30 runs for each program); ~1.5%
execution speedup in average on x86-64 darwin.
<rdar://problem/18021659>
llvm-svn: 218472
Chuang-Yu Cheng