The old mask in f24 wasn't well chosen because the lshr would always be zero.
CodeGen didn't detect this but InstCombine would. The new mask ensures
that both shifts are needed.
f26 is specifically testing for a wrap-around mask. The AND can be applied
to just the shift left, either before or after the shift. Again, CodeGen
kept it in the original form but InstCombine would mask after the shift
instead. The exact choice of NILF isn't important for the test so I just
dropped it and kept the rotate.
llvm-svn: 199115
The handling of ANY_EXTEND and ZERO_EXTEND was too strict. In this context
we can treat ZERO_EXTEND in much the same way as an AND and then also handle
outermost ZERO_EXTENDs.
I couldn't find a test that benefited from the ANY_EXTEND change, but it's
more obvious to write it this way once SIGN_EXTEND and ZERO_EXTEND are
handled differently.
llvm-svn: 197802
We would wrongly transform the testcase into the equivalent of an AND with 1.
The problem was that, when testing whether the shifted-in bits of the right
shift were significant, we used the width of the final zero-extended result
rather than the width of the shifted value.
llvm-svn: 195731
As on other hosts, the CPU identification instruction is priveleged,
so we need to look through /proc/cpuinfo. I copied the PowerPC way of
handling "generic".
Several tests were implicitly assuming z10 and so failed on z196.
llvm-svn: 193742
r186399 aggressively used the RISBG instruction for immediate ANDs,
both because it can handle some values that AND IMMEDIATE can't,
and because it allows the destination register to be different from
the source. I realized later while implementing the distinct-ops
support that it would be better to leave the choice up to
convertToThreeAddress() instead. The AND IMMEDIATE form is shorter
and is less likely to be cracked.
This is a problem for 32-bit ANDs because we assume that all 32-bit
operations will leave the high word untouched, whereas RISBG used in
this way will either clear the high word or copy it from the source
register. The patch uses the z196 instruction RISBLG for this instead.
This means that z10 will be restricted to NILL, NILH and NILF for
32-bit ANDs, but I think that should be OK for now. Although we're
using z10 as the base architecture, the optimization work is going
to be focused more on z196 and zEC12.
llvm-svn: 187492
The original code only folded SRA into ROTATE ... SELECTED BITS
if there was no outer shift. This patch splits out that check
and generalises it slightly. The extra cases aren't really that
interesting, but this is paving the way for RNSBG support.
llvm-svn: 186571
Another patch in the series to make more use of R.SBG. This one extends
r186072 and r186073 to handle cases where the AND is inside the shift.
llvm-svn: 186399
This update was done with the following bash script:
find test/CodeGen -name "*.ll" | \
while read NAME; do
echo "$NAME"
if ! grep -q "^; *RUN: *llc.*debug" $NAME; then
TEMP=`mktemp -t temp`
cp $NAME $TEMP
sed -n "s/^define [^@]*@\([A-Za-z0-9_]*\)(.*$/\1/p" < $NAME | \
while read FUNC; do
sed -i '' "s/;\(.*\)\([A-Za-z0-9_-]*\):\( *\)$FUNC: *\$/;\1\2-LABEL:\3$FUNC:/g" $TEMP
done
sed -i '' "s/;\(.*\)-LABEL-LABEL:/;\1-LABEL:/" $TEMP
sed -i '' "s/;\(.*\)-NEXT-LABEL:/;\1-NEXT:/" $TEMP
sed -i '' "s/;\(.*\)-NOT-LABEL:/;\1-NOT:/" $TEMP
sed -i '' "s/;\(.*\)-DAG-LABEL:/;\1-DAG:/" $TEMP
mv $TEMP $NAME
fi
done
llvm-svn: 186280
Richard Sandiford