This patch adds tablegen patterns to select F16C float-to-half-float
conversion instructions from 'f32_to_f16' and 'f16_to_f32' dag nodes.
If the target doesn't have F16C, then 'f32_to_f16' and 'f16_to_f32'
are expanded into library calls.
llvm-svn: 212293
This patch teaches method 'LowerVECTOR_SHUFFLE' to give higher precedence to
the check for 'isBlendMask'; the idea is that, when possible, we should firstly
check if a shuffle performs a blend, and in case, try to lower it into a BLENDI
instead of selecting a SHUFP or (worse) a VPERM2X128.
In general:
- AVX VBLENDPS/D always have better latency and throughput than VPERM2F128;
- BLENDPS/D instructions tend to always have better 'reciprocal throughput'
than the equivalent SHUFPS/D;
- Both BLENDPS/D and SHUFPS/D are often decoded into the same number of
m-ops; however, a m-op obtained from a BLENDPS/D can be scheduled to more
than one execution port.
This patch:
- Moves the check for 'isBlendMask' immediately before the check for
'isSHUFPMask' within method 'LowerVECTOR_SHUFFLE';
- Updates existing tests for sse/avx shuffle/blend instructions to verify
that we select (v)blendps/d when possible (instead of (v)shufps/d or
vperm2f128).
llvm-svn: 211720
This patch teaches the backend how to combine a build_vector that implements
an 'addsub' between packed float vectors into a sequence of vector add
and vector sub followed by a VSELECT.
The new VSELECT is expected to be lowered into a BLENDI.
At ISel stage, the sequence 'vector add + vector sub + BLENDI' is
pattern-matched against ISel patterns added at r211427 to select
'addsub' instructions.
Added three more ISel patterns for ADDSUB.
Added test sse3-avx-addsub-2.ll to verify that we correctly emit 'addsub'
instructions.
llvm-svn: 211679
This patch adds ISel patterns to select SSE3/AVX ADDSUB instructions
from a sequence of "vadd + vsub + blend".
Example:
///
typedef float float4 __attribute__((ext_vector_type(4)));
float4 foo(float4 A, float4 B) {
float4 X = A - B;
float4 Y = A + B;
return (float4){X[0], Y[1], X[2], Y[3]};
}
///
Before this patch, (with flag -mcpu=corei7) llc produced the following
assembly sequence:
movaps %xmm0, %xmm2
addps %xmm1, %xmm2
subps %xmm1, %xmm0
blendps $10, %xmm2, %xmm0
With this patch, we now get a single
addsubps %xmm1, %xmm0
llvm-svn: 211427
instructions available as synthetic SDNodes PACKSS and PACKUS that will
select to the correct instruction variants based on the return type.
This allows us to use these rather important instructions when lowering
vector shuffles.
Also moves the relevant instruction definitions to be split out from
the fully generic multiclasses to allow them to match these new SDNodes
in the same way that the UNPCK instructions do.
No functionality should actually be changed here.
llvm-svn: 211332
The corresponding CFE patch replaces these intrinsics with vector initializers
in avxintrin.h. This patch removes the LLVM intrinsics from the backend.
We now stop lowering at X86ISD::VBROADCAST custom node rather than lowering
that further to the intrinsics.
The patch only changes VBROADCASTS* and leaves VBROADCAST[FI]128 to continue
to use intrinsics. As explained in the CFE patch, the reason is that we
currently don't generate as good code for them without the intrinsics.
CodeGen/X86/avx-vbroadcast.ll already provides coverage for this change. It
checks that for a series of insertelements we generate the appropriate
vbroadcast instruction.
Also verified that there was no assembly change in the test-suite before and
after this patch.
llvm-svn: 209864
Summary:
When inserting an element that's coming from a vector load or a broadcast
of a vector (or scalar) load, combine the load into the insertps
instruction.
Added PerformINSERTPSCombine for the case where we need to fix the load
(load of a vector + insertps with a non-zero CountS).
Added patterns for the broadcasts.
Also added tests for SSE4.1, AVX, and AVX2.
Reviewers: delena, nadav, craig.topper
Subscribers: llvm-commits
Differential Revision: http://reviews.llvm.org/D3581
llvm-svn: 209156
Previously, TableGen assumed that every aliased operand consumed precisely 1
MachineInstr slot (this was reasonable because until a couple of days ago,
nothing more complicated was eligible for printing).
This allows a couple more ARM64 aliases to print so we can remove the special
code.
On the X86 side, I've gone for explicit AT&T size specifiers as the default, so
turned off a few of the aliases that would have just started printing.
llvm-svn: 208880
Summary:
The INSERTPS pattern fragment was called insrtps (mising 'e'), which
would make it harder to grep for the patterns related to this instruction.
Renaming it to use the proper instruction name.
Reviewers: nadav
CC: llvm-commits
Differential Revision: http://reviews.llvm.org/D3443
llvm-svn: 206779
AVX supports logical operations using an operand from memory. Unfortunately
because integer operations were not added until AVX2 the AVX1 logical
operation's types were preventing the isel from folding the loads. In a limited
number of cases the peephole optimizer would fold the loads, but most were
missed. This patch adds explicit patterns with appropriate casts in order for
these loads to be folded.
The included test cases run on reduced examples and disable the peephole
optimizer to ensure the folds are being pattern matched.
Patch by Louis Gerbarg <lgg@apple.com>
rdar://16355124
llvm-svn: 205938
Those patterns are used when the load cannot be folded into the related broadcast
during the select phase.
This happens when the load gets additional uses that were not anticipated during
the previous lowering phases (constant vector to constant load, then constant
load reused) or when selection DAG is not able to prove that folding the load
will not create a cycle in the DAG.
<rdar://problem/16074331>
llvm-svn: 204631
The patch defines new or refines existing generic scheduling classes to match
the behavior of the SSE instructions.
It also maps those scheduling classes on the related SSE instructions.
<rdar://problem/15607571>
llvm-svn: 202065
Original commits messages:
Add MRMXr/MRMXm form to X86 for use by instructions which treat the 'reg' field of modrm byte as a don't care value. Will allow for simplification of disassembler code.
Simplify a bunch of code by removing the need for the x86 disassembler table builder to know about extended opcodes. The modrm forms are sufficient to convey the information.
llvm-svn: 201065
r201059 appears to cause a crash in a bootstrapped build of clang. Craig
isn't available to look at it right now, so I'm reverting it while he
investigates.
llvm-svn: 201064
Generalize the AArch64 .td nodes for AssertZext and AssertSext. Use
them to match the relevant pextr store instructions.
The test widen_load-2.ll requires a slight change because with the
stores gone, the remaining instructions are scheduled in a different
order.
Add test cases for SSE4 and AVX variants.
Resolves rdar://13414672.
Patch by Adam Nemet <anemet@apple.com>.
llvm-svn: 200957
I believe VZEXT_MOVL means "zero all vector elements except the first" (and
should have identical input & output types) whereas VZEXT means "zero extend
each element of a vector (discarding higher elements if necessary)".
For example:
(v4i32 (vzext (v16i8 ...)))
should zero extend the low 4 bytes of the incoming vector to 32-bits,
discarding higher bytes.
However, somewhere in the past, these two concepts had become confused, even
leading to a nonsensical VSEXT_MOVL.
This re-merges the nodes where appropriate (all VSEXT_MOVL -> VSEXT, VZEXT_MOVL
-> VZEXT when it's an actual extension).
rdar://problem/15981990
llvm-svn: 200918
That's what it actually means, and with 16-bit support it's going to be
a little more relevant since in a few corner cases we may actually want
to distinguish between 16-bit and 32-bit mode (for example the bare 'push'
aliases to pushw/pushl etc.)
Patch by David Woodhouse
llvm-svn: 197768
Added scalar compare VCMPSS, VCMPSD.
Implemented LowerSELECT for scalar FP operations.
I replaced FSETCCss, FSETCCsd with one node type FSETCCs.
Node extract_vector_elt(v16i1/v8i1, idx) returns an element of type i1.
llvm-svn: 197384
a vector packed single/double fp operation followed by a vector insert.
The effect is that the backend coverts the packed fp instruction
followed by a vectro insert into a SSE or AVX scalar fp instruction.
For example, given the following code:
__m128 foo(__m128 A, __m128 B) {
__m128 C = A + B;
return (__m128) {c[0], a[1], a[2], a[3]};
}
previously we generated:
addps %xmm0, %xmm1
movss %xmm1, %xmm0
we now generate:
addss %xmm1, %xmm0
llvm-svn: 197145
immediately after SSE scalar fp instructions like addss or mulss.
Added patterns to select SSE scalar fp arithmetic instructions from a scalar
fp operation followed by a blend.
For example, given the following code:
__m128 foo(__m128 A, __m128 B) {
A[0] += B[0];
return A;
}
previously we generated:
addss %xmm0, %xmm1
movss %xmm1, %xmm0
now we generate:
addss %xmm1, %xmm0
llvm-svn: 196925
On sandy bridge (PR17654) we now get
vpxor %xmm1, %xmm1, %xmm1
vpunpckhbw %xmm1, %xmm0, %xmm2
vpunpcklbw %xmm1, %xmm0, %xmm0
vinsertf128 $1, %xmm2, %ymm0, %ymm0
On haswell it's a simple
vpmovzxbw %xmm0, %ymm0
There is a maze of duplicated and dead transforms and patterns in this
area. Remove the dead custom lowering of zext v8i16 to v8i32, that's
already handled by LowerAVXExtend.
llvm-svn: 193262
the instruction defenitions and ISEL reflect this.
Prior to this patch these instructions took an i32i8imm, and the high bits were
dropped during encoding. This led to incorrect behavior for shifts by
immediates higher than 255. This patch fixes that issue by detecting large
immediate shifts and returning constant zero (for logical shifts) or capping
the shift amount at an encodable value (for arithmetic shifts).
Fixes <rdar://problem/14968098>
llvm-svn: 193096
Andrea Di Biagio