Summary:
getShiftAmountTy for X86 returns MVT::i8. If a BSWAP or BITREVERSE is created that requires promotion and the difference between the original VT and the promoted VT is more than 255 then we won't able to create the constant.
This patch adds a check to replace the result from getShiftAmountTy to MVT::i32 if the difference won't fit. This should get legalized later when the shift is ultimately expanded since its clearly an illegal type that we're only promoting to make it a power of 2 bit width. Alternatively we could base the decision completely on the largest shift amount the promoted VT could use.
Vectors should be immune here because getShiftAmountTy always returns the incoming VT for vectors. Only the scalar shift amount can be changed by the targets.
Reviewers: eli.friedman, RKSimon, spatel
Reviewed By: RKSimon
Subscribers: llvm-commits
Differential Revision: https://reviews.llvm.org/D53232
llvm-svn: 344460
Enable enableMultipleCopyHints() on X86.
Original Patch by @jonpa:
While enabling the mischeduler for SystemZ, it was discovered that for some reason a test needed one extra seemingly needless COPY (test/CodeGen/SystemZ/call-03.ll). The handling for that is resulted in this patch, which improves the register coalescing by providing not just one copy hint, but a sorted list of copy hints. On SystemZ, this gives ~12500 less register moves on SPEC, as well as marginally less spilling.
Instead of improving just the SystemZ backend, the improvement has been implemented in common-code (calculateSpillWeightAndHint(). This gives a lot of test failures, but since this should be a general improvement I hope that the involved targets will help and review the test updates.
Differential Revision: https://reviews.llvm.org/D38128
llvm-svn: 342578
Discussed here:
http://lists.llvm.org/pipermail/llvm-dev/2018-January/120320.html
In preparation for adding support for named vregs we are changing the sigil for
physical registers in MIR to '$' from '%'. This will prevent name clashes of
named physical register with named vregs.
llvm-svn: 323922
As part of the unification of the debug format and the MIR format, print
MBB references as '%bb.5'.
The MIR printer prints the IR name of a MBB only for block definitions.
* find . \( -name "*.mir" -o -name "*.cpp" -o -name "*.h" -o -name "*.ll" \) -type f -print0 | xargs -0 sed -i '' -E 's/BB#" << ([a-zA-Z0-9_]+)->getNumber\(\)/" << printMBBReference(*\1)/g'
* find . \( -name "*.mir" -o -name "*.cpp" -o -name "*.h" -o -name "*.ll" \) -type f -print0 | xargs -0 sed -i '' -E 's/BB#" << ([a-zA-Z0-9_]+)\.getNumber\(\)/" << printMBBReference(\1)/g'
* find . \( -name "*.txt" -o -name "*.s" -o -name "*.mir" -o -name "*.cpp" -o -name "*.h" -o -name "*.ll" \) -type f -print0 | xargs -0 sed -i '' -E 's/BB#([0-9]+)/%bb.\1/g'
* grep -nr 'BB#' and fix
Differential Revision: https://reviews.llvm.org/D40422
llvm-svn: 319665
As part of the unification of the debug format and the MIR format,
always print registers as lowercase.
* Only debug printing is affected. It now follows MIR.
Differential Revision: https://reviews.llvm.org/D40417
llvm-svn: 319187
Summary:
Subregister liveness tracking is not implemented for X86 backend, so
sometimes the whole super register is said to be live, when only a
subregister is really live. That might happen if the def and the use
are located in different MBBs, see added fixup-bw-isnt.mir test.
However, using knowledge of the specific instructions handled by the
bw-fixup-pass we can get more precise liveness information which this
change does.
Reviewers: MatzeB, DavidKreitzer, ab, andrew.w.kaylor, craig.topper
Reviewed By: craig.topper
Subscribers: n.bozhenov, myatsina, llvm-commits, hiraditya
Patch by Andrei Elovikov <andrei.elovikov@intel.com>
Differential Revision: https://reviews.llvm.org/D37559
llvm-svn: 313524
An extension of D19978, this patch replaces the default BITREVERSE evaluation of individual bit masks+shifts with block mask+shifts when we have integer elements of power-of-2 bits in size.
After calling BSWAP to reverse the order of the constituent bytes (which typically follows a similar approach), every neighbouring 4-bits, 2-bits and finally 1-bit pairs are masked off and swapped over with shifts.
In doing so we can significantly reduce the number of operations required.
Differential Revision: https://reviews.llvm.org/D21578
llvm-svn: 276432
An identity COPY like this:
%AL = COPY %AL, %EAX<imp-def>
has no semantic effect, but encodes liveness information: Further users
of %EAX only depend on this instruction even though it does not define
the full register.
Replace the COPY with a KILL instruction in those cases to maintain this
liveness information. (This reverts a small part of r238588 but this
time adds a comment explaining why a KILL instruction is useful).
llvm-svn: 274952
It would be better to check the valid/expected size of the immediate operand, but this is
generally better than what we print right now.
Differential Revision: http://reviews.llvm.org/D20385
llvm-svn: 271114
Several backends have instructions to reverse the order of bits in an integer. Conceptually matching such patterns is similar to @llvm.bswap, and it was mentioned in http://reviews.llvm.org/D14234 that it would be best if these patterns were matched in InstCombine instead of reimplemented in every different target.
This patch introduces an intrinsic @llvm.bitreverse.i* that operates similarly to @llvm.bswap. For plumbing purposes there is also a new ISD node ISD::BITREVERSE, with simple expansion and promotion support.
The intention is that InstCombine's BSWAP detection logic will be extended to support BITREVERSE too, and @llvm.bitreverse intrinsics emitted (if the backend supports lowering it efficiently).
llvm-svn: 252878
Craig Topper