expanding pseudo LOAD_STATCK_GUARD using instructions that are normally used
in pic mode. This patch fixes the bug.
<rdar://problem/17886592>
llvm-svn: 214614
We were assuming all SBFX-like operations would have the shl/asr form, but
often when the field being extracted is an i8 or i16, we end up with a
SIGN_EXTEND_INREG acting on a shift instead. Simple enough to check for though.
llvm-svn: 213754
Although the final shifter operand is a rotate, this actually only matters for
the half-word extends when the amount == 24. Otherwise folding a shift in is
just as good.
llvm-svn: 213753
insertions.
The old behavior could cause arbitrarily bad memory usage in the DAG
combiner if there was heavy traffic of adding nodes already on the
worklist to it. This commit switches the DAG combine worklist to work
the same way as the instcombine worklist where we null-out removed
entries and only add new entries to the worklist. My measurements of
codegen time shows slight improvement. The memory utilization is
unsurprisingly dominated by other factors (the IR and DAG itself
I suspect).
This change results in subtle, frustrating churn in the particular order
in which DAG combines are applied which causes a number of minor
regressions where we fail to match a pattern previously matched by
accident. AFAICT, all of these should be using AddToWorklist to directly
or should be written in a less brittle way. None of the changes seem
drastically bad, and a few of the changes seem distinctly better.
A major change required to make this work is to significantly harden the
way in which the DAG combiner handle nodes which become dead
(zero-uses). Previously, we relied on the ability to "priority-bump"
them on the combine worklist to achieve recursive deletion of these
nodes and ensure that the frontier of remaining live nodes all were
added to the worklist. Instead, I've introduced a routine to just
implement that precise logic with no indirection. It is a significantly
simpler operation than that of the combiner worklist proper. I suspect
this will also fix some other problems with the combiner.
I think the x86 changes are really minor and uninteresting, but the
avx512 change at least is hiding a "regression" (despite the test case
being just noise, not testing some performance invariant) that might be
looked into. Not sure if any of the others impact specific "important"
code paths, but they didn't look terribly interesting to me, or the
changes were really minor. The consensus in review is to fix any
regressions that show up after the fact here.
Thanks to the other reviewers for checking the output on other
architectures. There is a specific regression on ARM that Tim already
has a fix prepped to commit.
Differential Revision: http://reviews.llvm.org/D4616
llvm-svn: 213727
The C and C++ semantics for compare_exchange require it to return a bool
indicating success. This gets mapped to LLVM IR which follows each cmpxchg with
an icmp of the value loaded against the desired value.
When lowered to ldxr/stxr loops, this extra comparison is redundant: its
results are implicit in the control-flow of the function.
This commit makes two changes: it replaces that icmp with appropriate PHI
nodes, and then makes sure earlyCSE is called after expansion to actually make
use of the opportunities revealed.
I've also added -{arm,aarch64}-enable-atomic-tidy options, so that
existing fragile tests aren't perturbed too much by the change. Many
of them either rely on undef/unreachable too pervasively to be
restored to something well-defined (particularly while making sure
they test the same obscure assert from many years ago), or depend on a
particular CFG shape, which is disrupted by SimplifyCFG.
rdar://problem/16227836
llvm-svn: 209883
This removes the -segmented-stacks command line flag in favor of a
per-function "split-stack" attribute.
Patch by Luqman Aden and Alex Crichton!
llvm-svn: 205997
More updating of tests to be explicit about the target triple rather than
relying on the default target triple supporting ARM mode.
Indicate to lit that object emission is not yet available for Windows on ARM.
llvm-svn: 205545
This commit only handles IfConvertTriangle. To update edge weights
of a successor, one interface is added to MachineBasicBlock:
/// Set successor weight of a given iterator.
setSuccWeight(succ_iterator I, uint32_t weight)
An existing testing case test/CodeGen/Thumb2/v8_IT_5.ll is updated,
since we now correctly update the edge weights, the cold block
is placed at the end of the function and we jump to the cold block.
llvm-svn: 200428
After all hard work to implement the EHABI and with the test-suite
passing, it's time to turn it on by default and allow users to
disable it as a work-around while we fix the eventual bugs that show
up.
This commit also remove the -arm-enable-ehabi-descriptors, since we
want the tables to be printed every time the EHABI is turned on
for non-Darwin ARM targets.
Although MCJIT EHABI is not working yet (needs linking with the right
libraries), this commit also fixes some relocations on MCJIT regarding
the EH tables/lib calls, and update some tests to avoid using EH tables
when none are needed.
The EH tests in the test-suite that were previously disabled on ARM
now pass with these changes, so a follow-up commit on the test-suite
will re-enable them.
llvm-svn: 200388
Originally, BLX was passed as operand #0 in MachineInstr and as operand
#2 in MCInst. But now, it's operand #2 in both cases.
This patch also removes unnecessary FileCheck in the test case added by r199127.
llvm-svn: 199928
The issue is caused when Post-RA scheduler reorders a bundle instruction
(IT block). However, it only flips the CPSR liveness of the bundle instruction,
leaves the instructions inside the bundle unchanged, which causes inconstancy and crashes
Thumb2SizeReduction.cpp::ReduceMBB().
llvm-svn: 199127
ARM symbol variants are written with parens instead of @ like this:
.word __GLOBAL_I_a(target1)
This commit adds support for parsing these symbol variants in
expressions. We introduce a new flag to MCAsmInfo that indicates the
parser should use parens to parse the symbol variant. The expression
parser is modified to look for symbol variants using parens instead
of @ when the corresponding MCAsmInfo flag is true.
The MCAsmInfo parens flag is enabled only for ARM on ELF.
By adding this flag to MCAsmInfo, we are able to get rid of
redundant ARM-specific symbol variants and use the generic variants
instead (e.g. VK_GOT instead of VK_ARM_GOT). We use the new
UseParensForSymbolVariant attribute in MCAsmInfo to correctly print
the symbol variants for arm.
To achive this we need to keep a handle to the MCAsmInfo in the
MCSymbolRefExpr class that we can check when printing the symbol
variant.
Updated Tests:
Changed case of symbol variant to match the generic kind.
test/CodeGen/ARM/tls-models.ll
test/CodeGen/ARM/tls1.ll
test/CodeGen/ARM/tls2.ll
test/CodeGen/Thumb2/tls1.ll
test/CodeGen/Thumb2/tls2.ll
PR18080
llvm-svn: 196424
By default, the behavior of IT block generation will be determinated
dynamically base on the arch (armv8 vs armv7). This patch adds backend
options: -arm-restrict-it and -arm-no-restrict-it. The former one
restricts the generation of IT blocks (the same behavior as thumbv8) for
both arches. The later one allows the generation of legacy IT block (the
same behavior as ARMv7 Thumb2) for both arches.
Clang will support -mrestrict-it and -mno-restrict-it, which is
compatible with GCC.
llvm-svn: 194592
Per original comment, the intention of this loop
is to go ahead and break the critical edge
(in order to sink this instruction) if there's
reason to believe doing so might "unblock" the
sinking of additional instructions that define
registers used by this one. The idea is that if
we have a few instructions to sink "together"
breaking the edge might be worthwhile.
This commit makes a few small changes
to help better realize this goal:
First, modify the loop to ignore registers
defined by this instruction. We don't
sink definitions of physical registers,
and sinking an SSA definition isn't
going to unblock an upstream instruction.
Second, ignore uses of physical registers.
Instructions that define physical registers are
rejected for sinking, and so moving this one
won't enable moving any defining instructions.
As an added bonus, while virtual register
use-def chains are generally small due
to SSA goodness, iteration over the uses
and definitions (used by hasOneNonDBGUse)
for physical registers like EFLAGS
can be rather expensive in practice.
(This is the original reason for looking at this)
Finally, to keep things simple continue
to only consider this trick for registers that
have a single use (via hasOneNonDBGUse),
but to avoid spuriously breaking critical edges
only do so if the definition resides
in the same MBB and therefore this one directly
blocks it from being sunk as well.
If sinking them together is meant to be,
let the iterative nature of this pass
sink the definition into this block first.
Update tests to accomodate this change,
add new testcase where sinking avoids pipeline stalls.
llvm-svn: 192608
I'd forgotten that "Requires" blocks override rather than add to the
constraints, so my pseudo-instruction was being selected in Thumb mode leading
to nonsense instructions.
rdar://problem/14817358
llvm-svn: 189096
Back in the mists of time (2008), it seems TableGen couldn't handle the
patterns necessary to match ARM's CMOV node that we convert select operations
to, so we wrote a lot of fairly hairy C++ to do it for us.
TableGen can deal with it now: there were a few minor differences to CodeGen
(see tests), but nothing obviously worse that I could see, so we should
probably address anything that *does* come up in a localised manner.
llvm-svn: 188995
- Instead of setting the suffixes in a bunch of places, just set one master
list in the top-level config. We now only modify the suffix list in a few
suites that have one particular unique suffix (.ml, .mc, .yaml, .td, .py).
- Aside from removing the need for a bunch of lit.local.cfg files, this enables
4 tests that were inadvertently being skipped (one in
Transforms/BranchFolding, a .s file each in DebugInfo/AArch64 and
CodeGen/PowerPC, and one in CodeGen/SI which is now failing and has been
XFAILED).
- This commit also fixes a bunch of config files to use config.root instead of
older copy-pasted code.
llvm-svn: 188513
indirect branches correctly. Under some circumstances, this led to the deletion
of basic blocks that were the destination of indirect branches. In that case it
left indirect branches to nowhere in the code.
This patch replaces, and is more general than either of the previous fixes for
indirect-branch-analysis issues, r181161 and r186461.
For other branches (not indirect) this refactor should have *almost* identical
behavior to the previous version. There are some corner cases where this
refactor is able to analyze blocks that the previous version could not (e.g.
this necessitated the update to thumb2-ifcvt2.ll).
<rdar://problem/14464830>
llvm-svn: 186735
All changes were made by the following bash script:
find test/CodeGen -name "*.ll" | \
while read NAME; do
echo "$NAME"
grep -q "^; *RUN: *llc.*debug" $NAME && continue
grep -q "^; *RUN:.*llvm-objdump" $NAME && continue
grep -q "^; *RUN: *opt.*" $NAME && continue
TEMP=`mktemp -t temp`
cp $NAME $TEMP
sed -n "s/^define [^@]*@\([A-Za-z0-9_]*\)(.*$/\1/p" < $NAME | \
while read FUNC; do
sed -i '' "s/;\([A-Za-z0-9_-]*\)\([A-Za-z0-9_-]*\):\( *\)$FUNC[:]* *\$/;\1\2-LABEL:\3$FUNC:/g" $TEMP
done
sed -i '' "s/;\(.*\)-LABEL-LABEL:/;\1-LABEL:/" $TEMP
sed -i '' "s/;\(.*\)-NEXT-LABEL:/;\1-NEXT:/" $TEMP
sed -i '' "s/;\(.*\)-NOT-LABEL:/;\1-NOT:/" $TEMP
sed -i '' "s/;\(.*\)-DAG-LABEL:/;\1-DAG:/" $TEMP
mv $TEMP $NAME
done
This script catches a superset of the cases caught by the script associated with commit r186280. It initially found some false positives due to unusual constructs in a minority of tests; all such cases were disambiguated first in commit r186621.
llvm-svn: 186624
This update was done with the following bash script:
find test/CodeGen -name "*.ll" | \
while read NAME; do
echo "$NAME"
if ! grep -q "^; *RUN: *llc.*debug" $NAME; then
TEMP=`mktemp -t temp`
cp $NAME $TEMP
sed -n "s/^define [^@]*@\([A-Za-z0-9_]*\)(.*$/\1/p" < $NAME | \
while read FUNC; do
sed -i '' "s/;\(.*\)\([A-Za-z0-9_-]*\):\( *\)$FUNC: *\$/;\1\2-LABEL:\3$FUNC:/g" $TEMP
done
sed -i '' "s/;\(.*\)-LABEL-LABEL:/;\1-LABEL:/" $TEMP
sed -i '' "s/;\(.*\)-NEXT-LABEL:/;\1-NEXT:/" $TEMP
sed -i '' "s/;\(.*\)-NOT-LABEL:/;\1-NOT:/" $TEMP
sed -i '' "s/;\(.*\)-DAG-LABEL:/;\1-DAG:/" $TEMP
mv $TEMP $NAME
fi
done
llvm-svn: 186280
This was done with the following sed invocation to catch label lines demarking function boundaries:
sed -i '' "s/^;\( *\)\([A-Z0-9_]*\):\( *\)test\([A-Za-z0-9_-]*\):\( *\)$/;\1\2-LABEL:\3test\4:\5/g" test/CodeGen/*/*.ll
which was written conservatively to avoid false positives rather than false negatives. I scanned through all the changes and everything looks correct.
llvm-svn: 186258
Propagate the fix from r185712 to Thumb2 codegen as well. Original
commit message applies here as well:
A "pkhtb x, x, y asr #num" uses the lower 16 bits of "y asr #num" and
packs them in the bottom half of "x". An arithmetic and logic shift are
only equivalent in this context if the shift amount is 16. We would be
shifting in ones into the bottom 16bits instead of zeros if "y" is
negative.
rdar://14338767
llvm-svn: 185982
ARM FastISel is currently only enabled for iOS non-Thumb1, and I'm working on
enabling it for other targets. As a first step I've fixed some of the tests.
Changes to ARM FastISel tests:
- Different triples don't generate the same relocations (especially
movw/movt versus constant pool loads). Use a regex to allow either.
- Mangling is different. Use a regex to allow either.
- The reserved registers are sometimes different, so registers get
allocated in a different order. Capture the names only where this
occurs.
- Add -verify-machineinstrs to some tests where it works. It doesn't
work everywhere it should yet.
- Add -fast-isel-abort to many tests that didn't have it before.
- Split out the VarArg test from fast-isel-call.ll into its own
test. This simplifies test setup because of --check-prefix.
Patch by JF Bastien
llvm-svn: 181801
The VDUP instruction source register doesn't allow a non-constant lane
index, so make sure we don't construct a ARM::VDUPLANE node asking it to
do so.
rdar://13328063
http://llvm.org/bugs/show_bug.cgi?id=13963
llvm-svn: 176413
This fixes some problems with too conservative checking where we were
marking all aliases of a register as used, and then also checking all
aliases when allocating a register.
<rdar://problem/13249625>
llvm-svn: 175782
When creating an allocation hint for a register pair, make sure the hint
for the physical register reference is still in the allocation order.
rdar://13240556
llvm-svn: 175541
These tests in particular try to use escaped square brackets as an
argument to grep, which is failing for me with native win32 python. It
appears the backslash is being lost near the CreateProcess*() call.
llvm-svn: 173506
are more expensive than the non-flag setting variant. Teach thumb2 size
reduction pass to avoid generating them unless we are optimizing for size.
rdar://12892707
llvm-svn: 170728
into a sbc with a positive number, the immediate should be complemented, not
negated. Also added a missing pattern for ARM codegen.
rdar://12559385
llvm-svn: 166613
aligned address. Based on patch by David Peixotto.
Also use vld1.64 / vst1.64 with 128-bit alignment to take advantage of alignment
hints. rdar://12090772, rdar://12238782
llvm-svn: 164089
Now that it is possible to dynamically tie MachineInstr operands,
predicated instructions are possible in SSA form:
%vreg3<def> = SUBri %vreg1, -2147483647, pred:14, pred:%noreg, %opt:%noreg
%vreg4<def,tied1> = MOVCCr %vreg3<tied0>, %vreg1, %pred:12, pred:%CPSR
Becomes a predicated SUBri with a tied imp-use:
SUBri %vreg1, -2147483647, pred:13, pred:%CPSR, opt:%noreg, %vreg1<imp-use,tied0>
This means that any instruction that is safe to move can be folded into
a MOVCC, and the *CC pseudo-instructions are no longer needed.
The test case changes reflect that Thumb2SizeReduce recognizes the
predicated instructions. It didn't understand the pseudos.
llvm-svn: 163274
This patch corrects the definition of umlal/smlal instructions and adds support
for matching them to the ARM dag combiner.
Bug 12213
Patch by Yin Ma!
llvm-svn: 163136
It is not my plan to duplicate the entire ARM instruction set with
predicated versions. We need a way of representing predicated
instructions in SSA form without requiring a separate opcode.
Then the pseudo-instructions can go away.
llvm-svn: 162061
The ARM select instructions are just predicated moves. If the select is
the only use of an operand, the instruction defining the operand can be
predicated instead, saving one instruction and decreasing register
pressure.
This implementation can turn AND/ORR/EOR instructions into their
corresponding ANDCC/ORRCC/EORCC variants. Ideally, we should be able to
predicate any instruction, but we don't yet support predicated
instructions in SSA form.
llvm-svn: 161994
another mechanical change accomplished though the power of terrible Perl
scripts.
I have manually switched some "s to 's to make escaping simpler.
While I started this to fix tests that aren't run in all configurations,
the massive number of tests is due to a really frustrating fragility of
our testing infrastructure: things like 'grep -v', 'not grep', and
'expected failures' can mask broken tests all too easily.
Essentially, I'm deeply disturbed that I can change the testsuite so
radically without causing any change in results for most platforms. =/
llvm-svn: 159547
through my perl nets.
With this, the test suite passes even if I force it to run with the
built-in shell test logic, except for a test which REQUIREs shell.
llvm-svn: 159529
This was done through the aid of a terrible Perl creation. I will not
paste any of the horrors here. Suffice to say, it require multiple
staged rounds of replacements, state carried between, and a few
nested-construct-parsing hacks that I'm not proud of. It happens, by
luck, to be able to deal with all the TCL-quoting patterns in evidence
in the LLVM test suite.
If anyone is maintaining large out-of-tree test trees, feel free to poke
me and I'll send you the steps I used to convert things, as well as
answer any painful questions etc. IRC works best for this type of thing
I find.
Once converted, switch the LLVM lit config to use ShTests the same as
Clang. In addition to being able to delete large amounts of Python code
from 'lit', this will also simplify the entire test suite and some of
lit's architecture.
Finally, the test suite runs 33% faster on Linux now. ;]
For my 16-hardware-thread (2x 4-core xeon e5520): 36s -> 24s
llvm-svn: 159525
Live ranges with a constrained register class may benefit from splitting
around individual uses. It allows the remaining live range to use a
larger register class where it may allocate. This is like spilling to a
different register class.
This is only attempted on constrained register classes.
<rdar://problem/11438902>
llvm-svn: 157354
Use a dedicated MachO load command to annotate data-in-code regions.
This is the same format the linker produces for final executable images,
allowing consistency of representation and use of introspection tools
for both object and executable files.
Data-in-code regions are annotated via ".data_region"/".end_data_region"
directive pairs, with an optional region type.
data_region_directive := ".data_region" { region_type }
region_type := "jt8" | "jt16" | "jt32" | "jta32"
end_data_region_directive := ".end_data_region"
The previous handling of ARM-style "$d.*" labels was broken and has
been removed. Specifically, it didn't handle ARM vs. Thumb mode when
marking the end of the section.
rdar://11459456
llvm-svn: 157062
This option has been disabled for a while, and it is going away so I can
clean up the coalescer code.
The tests that required physreg joining to be enabled were almost all of
the form "tiny function with interference between arguments and return
value". Such functions are usually inlined in the real world.
The problem exposed by phys_subreg_coalesce-3.ll is real, but fairly
rare.
llvm-svn: 157027
the feature set of v7a. This comes about if the user specifies something like
-arch armv7 -mcpu=cortex-m3. We shouldn't be generating instructions such as
uxtab in this case.
rdar://11318438
llvm-svn: 155601
both fallthrough and a conditional branch target the same successor.
Gracefully delete the conditional branch and introduce any unconditional
branch needed to reach the actual successor. This fixes memory
corruption in 2009-06-15-RegScavengerAssert.ll and possibly other tests.
Also, while I'm here fix a latent bug I spotted by inspection. I never
applied the same fundamental fix to this fallthrough successor finding
logic that I did to the logic used when there are no conditional
branches. As a consequence it would have selected landing pads had they
be aligned in just the right way here. I don't have a test case as
I spotted this by inspection, and the previous time I found this
required have of TableGen's source code to produce it. =/ I hate backend
bugs. ;]
Thanks to Jim Grosbach for helping me reason through this and reviewing
the fix.
llvm-svn: 154867
This is mostly to test the waters. I'd like to get results from FNT
build bots and other bots running on non-x86 platforms.
This feature has been pretty heavily tested over the last few months by
me, and it fixes several of the execution time regressions caused by the
inlining work by preventing inlining decisions from radically impacting
block layout.
I've seen very large improvements in yacr2 and ackermann benchmarks,
along with the expected noise across all of the benchmark suite whenever
code layout changes. I've analyzed all of the regressions and fixed
them, or found them to be impossible to fix. See my email to llvmdev for
more details.
I'd like for this to be in 3.1 as it complements the inliner changes,
but if any failures are showing up or anyone has concerns, it is just
a flag flip and so can be easily turned off.
I'm switching it on tonight to try and get at least one run through
various folks' performance suites in case SPEC or something else has
serious issues with it. I'll watch bots and revert if anything shows up.
llvm-svn: 154816
LSR always tries to make the ICmp in the loop latch use the incremented
induction variable. This allows the induction variable to be kept in a
single register.
When the induction variable limit is equal to the stride,
SimplifySetCC() would break LSR's hard work by transforming:
(icmp (add iv, stride), stride) --> (cmp iv, 0)
This forced us to use lea for the IC update, preventing the simpler
incl+cmp.
<rdar://problem/7643606>
<rdar://problem/11184260>
llvm-svn: 154119
When an strd instruction doesn't get the registers it wants, it can be
expanded into two str instructions. Make sure the first str doesn't kill
the base register in the case where the base and data registers are
identical:
t2STRi12 %R0<kill>, %R0, 4, pred:14, pred:%noreg
t2STRi12 %R2<kill>, %R0, 8, pred:14, pred:%noreg
<rdar://problem/11101911>
llvm-svn: 153611
The arm_neon intrinsics can create virtual registers from the DPair
register class which allows both even-odd and odd-even D-register pairs.
This fixes PR12389.
llvm-svn: 153603
* Removed test/lib/llvm.exp - it is no longer needed
* Deleted the dg.exp reading code from test/lit.cfg. There are no dg.exp files
left in the test suite so this code is no longer required. test/lit.cfg is
now much shorter and clearer
* Removed a lot of duplicate code in lit.local.cfg files that need access to
the root configuration, by adding a "root" attribute to the TestingConfig
object. This attribute is dynamically computed to provide the same
information as was previously provided by the custom getRoot functions.
* Documented the config.root attribute in docs/CommandGuide/lit.pod
llvm-svn: 153408
When an outgoing call takes more than 2k of arguments on the stack, we
don't allocate that call frame in the prolog, but adjust the stack
pointer immediately before the call instead.
This causes problems with the emergency spill slot because PEI can't
track stack pointer adjustments on the second pass, and if the outgoing
arguments are too big, SP can't be used to reach the emergency spill
slot at all.
Work around these problems by ensuring there is a base or frame pointer
that can be used to access the emergency spill slot.
<rdar://problem/10917166>
llvm-svn: 151604
The tied source operand of tMUL is the second source operand, not the
first like every other two-address thumb instruction. Special case it
in the size reduction pass to make sure we create the tMUL instruction
properly.
llvm-svn: 151315
live across BBs before register allocation. This miscompiled 197.parser
when a cmp + b are optimized to a cbnz instruction even though the CPSR def
is live-in a successor.
cbnz r6, LBB89_12
...
LBB89_12:
ble LBB89_1
The fix consists of two parts. 1) Teach LiveVariables that some unallocatable
registers might be liveouts so don't mark their last use as kill if they are.
2) ARM constantpool island pass shouldn't form cbz / cbnz if the conditional
branch does not kill CPSR.
rdar://10676853
llvm-svn: 148168
This function runs after all constant islands have been placed, and may
shrink some instructions to their 2-byte forms. This can actually cause
some constant pool entries to move out of range because of growing
alignment padding.
Treat instructions that may be shrunk the same as inline asm - they
erode the known alignment bits.
Also reinstate an old assertion in verify(). It is correct now that
basic block offsets include alignments.
Add a single large test case that will hopefully exercise many parts of
the constant island pass.
<rdar://problem/10670199>
llvm-svn: 147885
define physical registers. It's currently very restrictive, only catching
cases where the CE is in an immediate (and only) predecessor. But it catches
a surprising large number of cases.
rdar://10660865
llvm-svn: 147827
Now that canRealignStack() understands frozen reserved registers, it is
safe to use it for aligned spill instructions.
It will only return true if the registers reserved at the beginning of
register allocation allow for dynamic stack realignment.
<rdar://problem/10625436>
llvm-svn: 147579
This patch caused a miscompilation of oggenc because a frame pointer was
suddenly needed halfway through register allocation.
<rdar://problem/10625436>
llvm-svn: 147487
ARM targets with NEON units have access to aligned vector loads and
stores that are potentially faster than unaligned operations.
Add support for spilling the callee-saved NEON registers to an aligned
stack area using 16-byte aligned NEON loads and store.
This feature is off by default, controlled by an -align-neon-spills
command line option.
llvm-svn: 147211
Use the spill slot alignment as well as the local variable alignment to
determine when the stack needs to be realigned. This works now that the
ARM target can always realign the stack by using a base pointer.
Still respect the ARMBaseRegisterInfo::canRealignStack() function
vetoing a realigned stack. Don't use aligned spill code in that case.
llvm-svn: 146997
to finalize MI bundles (i.e. add BUNDLE instruction and computing register def
and use lists of the BUNDLE instruction) and a pass to unpack bundles.
- Teach more of MachineBasic and MachineInstr methods to be bundle aware.
- Switch Thumb2 IT block to MI bundles and delete the hazard recognizer hack to
prevent IT blocks from being broken apart.
llvm-svn: 146542
I followed three heuristics for deciding whether to set 'true' or
'false':
- Everything target independent got 'true' as that is the expected
common output of the GCC builtins.
- If the target arch only has one way of implementing this operation,
set the flag in the way that exercises the most of codegen. For most
architectures this is also the likely path from a GCC builtin, with
'true' being set. It will (eventually) require lowering away that
difference, and then lowering to the architecture's operation.
- Otherwise, set the flag differently dependending on which target
operation should be tested.
Let me know if anyone has any issue with this pattern or would like
specific tests of another form. This should allow the x86 codegen to
just iteratively improve as I teach the backend how to differentiate
between the two forms, and everything else should remain exactly the
same.
llvm-svn: 146370
register dependency (rather than glue them together). This is general
goodness as it gives scheduler more freedom. However it is motivated by
a nasty bug in isel.
When a i64 sub is expanded to subc + sube.
libcall #1
\
\ subc
\ / \
\ / \
\ / libcall #2
sube
If the libcalls are not serialized (i.e. both have chains which are dag
entry), legalizer can serialize them in arbitrary orders. If it's
unlucky, it can force libcall #2 before libcall #1 in the above case.
subc
|
libcall #2
|
libcall #1
|
sube
However since subc and sube are "glued" together, this ends up being a
cycle when the scheduler combine subc and sube as a single scheduling
unit.
The right solution is to fix LegalizeType too chains the libcalls together.
However, LegalizeType is not processing nodes in order so that's harder than
it should be. For now, the move to physical register dependency will do.
rdar://10019576
llvm-svn: 138791
Fix base register type and canonicallize to the "ldm" spelling rather than
"ldmia." Add diagnostics for incorrect writeback token and out-of-range
registers.
llvm-svn: 137986
(including compilation, assembly). Move relocation model Reloc::Model from
TargetMachine to MCCodeGenInfo so it's accessible even without TargetMachine.
llvm-svn: 135468
if (x != 0) x = 1
if (x == 1) x = 1
Previous codegen looks like this:
mov r1, r0
cmp r1, #1
mov r0, #0
moveq r0, #1
The naive lowering select between two different values. It should recognize the
test is equality test so it's more a conditional move rather than a select:
cmp r0, #1
movne r0, #0
rdar://9758317
llvm-svn: 135017
The normal tBX instruction is predicable, so there's no reason the
pseudos for using it as a return shouldn't be. Gives us some nice code-gen
improvements as can be seen by the test changes. In particular, several
tests now have to disable if-conversion because it works too well and defeats
the test.
llvm-svn: 134746
The DSP instructions in the Thumb2 instruction set are an optional extension
in the Cortex-M* archtitecture. When present, the implementation is considered
an "ARMv7E-M implementation," and when not, an "ARMv7-M implementation."
Add a subtarget feature hook for the v7e-m instructions and hook it up. The
cortex-m3 cpu is an example of a v7m implementation, while the cortex-m4 is
a v7e-m implementation.
rdar://9572992
llvm-svn: 134261
Fix a FIXME and allow predication (in Thumb2) for the T1 register to
register MOV instructions. This allows some better codegen with
if-conversion (as seen in the test updates), plus it lays the groundwork
for pseudo-izing the tMOVCC instructions.
llvm-svn: 134197
It's just a t2LDMIA_UPD instruction with extra codegen properties, so it
doesn't need the encoding information. As a side-benefit, we now correctly
recognize for instruction printing as a 'pop' instruction.
llvm-svn: 134173
for pre-2.9 bitcode files. We keep x86 unaligned loads, movnt, crc32, and the
target indep prefetch change.
As usual, updating the testsuite is a PITA.
llvm-svn: 133337
we try to branch to them.
Before we were creating successor lists with duplicated entries. Fixing that
found a bug in isBlockOnlyReachableByFallthrough that would causes it to
return the wrong answer for
-----------
...
jne foo
jmp bar
foo:
----------
llvm-svn: 132882
of reserved registers.
Use RegisterClassInfo in RABasic as well. This slightly changes som
allocation orders because RegisterClassInfo puts CSR aliases last.
llvm-svn: 132581
by non-CMP expressions. The executable test case (129821) would test
this as well, if we had an "-O0 -disable-arm-fast-isel" LLVM-GCC
tester. Alas, the ARM assembly would be very difficult to check with
FileCheck.
The thumb2-cbnz.ll test is affected; it generates larger code (tst.w
vs. cmp #0), but I believe the new version is correct.
rdar://problem/9298790
llvm-svn: 131261
Original message:
Teach MachineCSE how to do simple cross-block CSE involving physregs. This allows, for example, eliminating duplicate cmpl's on x86. Part of rdar://problem/8259436 .
llvm-svn: 130877
These tests all follow the same pattern:
mov r2, r0
movs r0, #0
$CMP r2, r1
it eq
moveq r0, #1
bx lr
The first 'mov' can be eliminated by rematerializing 'movs r0, #0' below the
test instruction:
$CMP r0, r1
mov.w r0, #0
it eq
moveq r0, #1
bx lr
So far, only physreg coalescing can do that. The register allocators won't yet
split live ranges just to eliminate copies. They can learn, but this particular
problem is not likely to show up in real code. It only appears because r0 is
used for both the function argument and return value.
llvm-svn: 130858
more callee-saved registers and introduce copies. Only allows it if scheduling
a node above calls would end up lessen register pressure.
Call operands also has added ABI restrictions for register allocation, so be
extra careful with hoisting them above calls.
rdar://9329627
llvm-svn: 130245
Fixes Thumb2 ADCS and SBCS lowering: <rdar://problem/9275821>.
t2ADCS/t2SBCS are now pseudo instructions, consistent with ARM, so the
assembly printer correctly prints the 's' suffix.
Fixes Thumb2 adde -> SBC matching to check for live/dead carry flags.
Fixes the internal ARM machine opcode mnemonic for ADCS/SBCS.
Fixes ARM SBC lowering to check for live carry (potential bug).
llvm-svn: 130048
add <rd>, sp, #<imm8>
ldr <rd>, [sp, #<imm8>]
When the offset from sp is multiple of 4 and in range of 0-1020.
This saves code size by utilizing 16-bit instructions.
rdar://9321541
llvm-svn: 129971
Additional fixes:
Do something reasonable for subtargets with generic
itineraries by handle node latency the same as for an empty
itinerary. Now nodes default to unit latency unless an itinerary
explicitly specifies a zero cycle stage or it is a TokenFactor chain.
Original fixes:
UnitsSharePred was a source of randomness in the scheduler: node
priority depended on the queue data structure. I rewrote the recent
VRegCycle heuristics to completely replace the old heuristic without
any randomness. To make the ndoe latency adjustments work, I also
needed to do something a little more reasonable with TokenFactor. I
gave it zero latency to its consumers and always schedule it as low as
possible.
llvm-svn: 129421
Akira Hatanaka