lammps/doc/restart.txt

"LAMMPS WWW Site"_lws - "LAMMPS Documentation"_ld - "LAMMPS Commands"_lc :c

:link(lws,http://lammps.sandia.gov)
:link(ld,Manual.html)
:link(lc,Section_commands.html#comm)

:line

restart command :h3

[Syntax:]

restart 0
restart N root keyword value ...
restart N file1 file2 keyword value ... :pre

N = write a restart file every this many timesteps :ulb,l
N can be a variable (see below) :l
root = filename to which timestep # is appended :l
file1,file2 = two full filenames, toggle between them when writing file :l
zero or more keyword/value pairs may be appended :l
keyword = {fileper} or {nfile} :l
  {fileper} arg = Np
    Np = write one file for every this many processors
  {nfile} arg = Nf
    Nf = write this many files, one from each of Nf processors :pre
:ule

[Examples:]

restart 0
restart 1000 poly.restart
restart 1000 restart.*.equil
restart 10000 poly.%.1 poly.%.2
restart v_mystep poly.restart :pre

[Description:]

Write out a binary restart file every so many timesteps, in either or
both of two modes, as a run proceeds.  A value of 0 means do not write
out any restart files.  The two modes are as follows.  If one filename
is specified, a series of filenames will be created which include the
timestep in the filename.  If two filenames are specified, only 2
restart files will be created, with those names.  LAMMPS will toggle
between the 2 names as it writes successive restart files.

Note that you can specify the restart command twice, once with a
single filename and once with two filenames.  This would allow you,
for example, to write out archival restart files every 100000 steps
using a single filenname, and more frequent temporary restart files
every 1000 steps, using two filenames.  Using restart 0 will turn off
both modes of output.

Similar to "dump"_dump.html files, the restart filename(s) can contain
two wild-card characters.

If a "*" appears in the single filename, it is replaced with the
current timestep value.  This is only recognized when a single
filename is used (not when toggling back and forth).  Thus, the 3rd
example above creates restart files as follows: restart.1000.equil,
restart.2000.equil, etc.  If a single filename is used with no "*",
then the timestep value is appended.  E.g. the 2nd example above
creates restart files as follows: poly.restart.1000,
poly.restart.2000, etc.

If a "%" character appears in the restart filename(s), then one file
is written for each processor and the "%" character is replaced with
the processor ID from 0 to P-1.  An additional file with the "%"
replaced by "base" is also written, which contains global information.
For example, the files written on step 1000 for filename restart.%
would be restart.base.1000, restart.0.1000, restart.1.1000, ...,
restart.P-1.1000.  This creates smaller files and can be a fast mode
of output and subsequent input on parallel machines that support
parallel I/O.  The optional {fileper} and {nfile} keywords discussed
below can alter the number of files written.

Restart files are written on timesteps that are a multiple of N but
not on the first timestep of a run or minimization.  You can use the
"write_restart"_write_restart.html command to write a restart file
before a run begins.  A restart file is not written on the last
timestep of a run unless it is a multiple of N.  A restart file is
written on the last timestep of a minimization if N > 0 and the
minimization converges.

Instead of a numeric value, N can be specifed as an "equal-style
variable"_variable.html, which should be specified as v_name, where
name is the variable name.  In this case, the variable is evaluated at
the beginning of a run to determine the next timestep at which a
restart file will be written out.  On that timestep, the variable will
be evaluated again to determine the next timestep, etc.  Thus the
variable should return timestep values.  See the stagger() and
logfreq() and stride() math functions for "equal-style
variables"_variable.html, as examples of useful functions to use in
this context.  Other similar math functions could easily be added as
options for "equal-style variables"_variable.html.

For example, the following commands will write restart files 
every step from 1100 to 1200, and could be useful for debugging
a simulation where something goes wrong at step 1163:

variable	s equal stride(1100,1200,1)
restart		v_s tmp.restart :pre

:line

See the "read_restart"_read_restart.html command for information about
what is stored in a restart file.  

Restart files can be read by a "read_restart"_read_restart.html
command to restart a simulation from a particular state.  Because the
file is binary (to enable exact restarts), it may not be readable on
another machine.  In this case, you can use the "-r command-line
switch"_Section_start.html#start_7 to convert a restart file to a data
file.

:line

The optional {nfile} or {fileper} keywords can be used in conjunction
with the "%" wildcard character in the specified restart file name(s).
As explained above, the "%" character causes the restart file to be
written in pieces, one piece for each of P processors.  By default P =
the number of processors the simulation is running on.  The {nfile} or
{fileper} keyword can be used to set P to a smaller value, which can
be more efficient when running on a large number of processors.

The {nfile} keyword sets P to the specified Nf value.  For example, if
Nf = 4, and the simulation is running on 100 processors, 4 files will
be written, by processors 0,25,50,75.  Each will collect information
from itself and the next 24 processors and write it to a restart file.

For the {fileper} keyword, the specified value of Np means write one
file for every Np processors.  For example, if Np = 4, every 4th
processor (0,4,8,12,etc) will collect information from itself and the
next 3 processors and write it to a restart file.

:line

[Restrictions:] none

[Related commands:]

"write_restart"_write_restart.html, "read_restart"_read_restart.html

[Default:]

restart 0 :pre