forked from lijiext/lammps
158 lines
6.6 KiB
Plaintext
158 lines
6.6 KiB
Plaintext
"LAMMPS WWW Site"_lws - "LAMMPS Documentation"_ld - "LAMMPS Commands"_lc :c
|
|
|
|
:link(lws,http://lammps.sandia.gov)
|
|
:link(ld,Manual.html)
|
|
:link(lc,Section_commands.html#comm)
|
|
|
|
:line
|
|
|
|
fix thermal/conductivity command :h3
|
|
|
|
[Syntax:]
|
|
|
|
fix ID group-ID thermal/conductivity N edim Nbin keyword value ... :pre
|
|
|
|
ID, group-ID are documented in "fix"_fix.html command :ulb,l
|
|
thermal/conductivity = style name of this fix command :l
|
|
N = perform kinetic energy exchange every N steps :l
|
|
edim = {x} or {y} or {z} = direction of kinetic energy transfer :l
|
|
Nbin = # of layers in edim direction (must be even number) :l
|
|
|
|
zero or more keyword/value pairs may be appended :l
|
|
keyword = {swap} :l
|
|
{swap} value = Nswap = number of swaps to perform every N steps :pre
|
|
:ule
|
|
|
|
[Examples:]
|
|
|
|
fix 1 all thermal/conductivity 100 z 20
|
|
fix 1 all thermal/conductivity 50 z 20 swap 2 :pre
|
|
|
|
[Description:]
|
|
|
|
Use the Muller-Plathe algorithm described in "this
|
|
paper"_#Muller-Plathe to exchange kinetic energy between two particles
|
|
in different regions of the simulation box every N steps. This
|
|
induces a temperature gradient in the system. As described below this
|
|
enables a thermal conductivity of the fluid to be calculated. This
|
|
algorithm is sometimes called a reverse non-equilibrium MD (reverse
|
|
NEMD) approach to computing thermal conductivity. This is because the
|
|
usual NEMD approach is to impose a temperature gradient on the system
|
|
and measure the response as the resulting heat flux. In the
|
|
Muller-Plathe method, the heat flux is imposed, and the temperature
|
|
gradient is the system's response.
|
|
|
|
See the "compute heat/flux"_compute_heat_flux.html command for details
|
|
on how to compute thermal conductivity in an alternate way, via the
|
|
Green-Kubo formalism.
|
|
|
|
The simulation box is divided into {Nbin} layers in the {edim}
|
|
direction, where the layer 1 is at the low end of that dimension and
|
|
the layer {Nbin} is at the high end. Every N steps, Nswap pairs of
|
|
atoms are chosen in the following manner. Only atoms in the fix group
|
|
are considered. The hottest Nswap atoms in layer 1 are selected.
|
|
Similarly, the coldest Nswap atoms in the "middle" layer (see below)
|
|
are selected. The two sets of Nswap atoms are paired up and their
|
|
velocities are exchanged. This effectively swaps their kinetic
|
|
energies, assuming their masses are the same. Over time, this induces
|
|
a temperature gradient in the system which can be measured using
|
|
commands such as the following, which writes the temperature profile
|
|
(assuming z = edim) to the file tmp.profile:
|
|
|
|
compute ke all ke/atom
|
|
variable temp atom c_ke/1.5
|
|
fix 3 all ave/spatial 10 100 1000 z lower 0.05 v_temp &
|
|
file tmp.profile units reduced :pre
|
|
|
|
Note that by default, Nswap = 1, though this can be changed by the
|
|
optional {swap} keyword. Setting this parameter appropriately, in
|
|
conjunction with the swap rate N, allows the heat flux to be adjusted
|
|
across a wide range of values, and the kinetic energy to be exchanged
|
|
in large chunks or more smoothly.
|
|
|
|
The "middle" layer for velocity swapping is defined as the {Nbin}/2 +
|
|
1 layer. Thus if {Nbin} = 20, the two swapping layers are 1 and 11.
|
|
This should lead to a symmetric temperature profile since the two
|
|
layers are separated by the same distance in both directions in a
|
|
periodic sense. This is why {Nbin} is restricted to being an even
|
|
number.
|
|
|
|
As described below, the total kinetic energy transferred by these
|
|
swaps is computed by the fix and can be output. Dividing this
|
|
quantity by time and the cross-sectional area of the simulation box
|
|
yields a heat flux. The ratio of heat flux to the slope of the
|
|
temperature profile is proportional to the thermal conductivity of the
|
|
fluid, in appropriate units. See the "Muller-Plathe
|
|
paper"_#Muller-Plathe for details.
|
|
|
|
IMPORTANT NOTE: If your system is periodic in the direction of the
|
|
heat flux, then the flux is going in 2 directions. This means the
|
|
effective heat flux in one direction is reduced by a factor of 2. You
|
|
will see this in the equations for thermal conductivity (kappa) in the
|
|
Muller-Plathe paper. LAMMPS is simply tallying kinetic energy which
|
|
does not account for whether or not your system is periodic; you must
|
|
use the value appropriately to yield a kappa for your system.
|
|
|
|
IMPORTANT NOTE: After equilibration, if the temperature gradient you
|
|
observe is not linear, then you are likely swapping energy too
|
|
frequently and are not in a regime of linear response. In this case
|
|
you cannot accurately infer a thermal conductivity and should try
|
|
increasing the Nevery parameter.
|
|
|
|
[Restart, fix_modify, output, run start/stop, minimize info:]
|
|
|
|
No information about this fix is written to "binary restart
|
|
files"_restart.html. None of the "fix_modify"_fix_modify.html options
|
|
are relevant to this fix.
|
|
|
|
This fix computes a global scalar which can be accessed by various
|
|
"output commands"_Section_howto.html#howto_15. The scalar is the
|
|
cummulative kinetic energy transferred between the bottom and middle
|
|
of the simulation box (in the {edim} direction) is stored as a scalar
|
|
quantity by this fix. This quantity is zeroed when the fix is defined
|
|
and accumlates thereafter, once every N steps. The units of the
|
|
quantity are energy; see the "units"_units.html command for details.
|
|
The scalar value calculated by this fix is "intensive".
|
|
|
|
No parameter of this fix can be used with the {start/stop} keywords of
|
|
the "run"_run.html command. This fix is not invoked during "energy
|
|
minimization"_minimize.html.
|
|
|
|
[Restrictions:]
|
|
|
|
Swaps conserve both momentum and kinetic energy, even if the masses of
|
|
the swapped atoms are not equal. Thus you should not need to
|
|
thermostat the system. If you do use a thermostat, you may want to
|
|
apply it only to the non-swapped dimensions (other than {vdim}).
|
|
|
|
LAMMPS does not check, but you should not use this fix to swap the
|
|
kinetic energy of atoms that are in constrained molecules, e.g. via
|
|
"fix shake"_fix_shake.html or "fix rigid"_fix_rigid.html. This is
|
|
because application of the constraints will alter the amount of
|
|
transferred momentum. You should, however, be able to use flexible
|
|
molecules. See the "Zhang paper"_#Zhang for a discussion and results
|
|
of this idea.
|
|
|
|
When running a simulation with large, massive particles or molecules
|
|
in a background solvent, you may want to only exchange kinetic energy
|
|
bewteen solvent particles.
|
|
|
|
[Related commands:]
|
|
|
|
"fix ave/spatial"_fix_ave_spatial.html, "fix
|
|
viscosity"_fix_viscosity.html, "compute
|
|
heat/flux"_compute_heat_flux.html
|
|
|
|
[Default:]
|
|
|
|
The option defaults are swap = 1.
|
|
|
|
:line
|
|
|
|
:link(Muller-Plathe)
|
|
[(Muller-Plathe)] Muller-Plathe, J Chem Phys, 106, 6082 (1997).
|
|
|
|
:link(Zhang)
|
|
[(Zhang)] Zhang, Lussetti, de Souza, Muller-Plathe, J Phys Chem B,
|
|
109, 15060-15067 (2005).
|