forked from lijiext/lammps
132 lines
4.2 KiB
Plaintext
132 lines
4.2 KiB
Plaintext
"Higher level section"_Python_head.html - "LAMMPS WWW Site"_lws -
|
|
"LAMMPS Documentation"_ld - "LAMMPS Commands"_lc :c
|
|
|
|
:link(lws,http://lammps.sandia.gov)
|
|
:link(ld,Manual.html)
|
|
:link(lc,Commands_all.html)
|
|
|
|
:line
|
|
|
|
Test the Python/LAMMPS interface :h3
|
|
|
|
To test if LAMMPS is callable from Python, launch Python interactively
|
|
and type:
|
|
|
|
>>> from lammps import lammps
|
|
>>> lmp = lammps() :pre
|
|
|
|
If you get no errors, you're ready to use LAMMPS from Python. If the
|
|
2nd command fails, the most common error to see is
|
|
|
|
OSError: Could not load LAMMPS dynamic library :pre
|
|
|
|
which means Python was unable to load the LAMMPS shared library. This
|
|
typically occurs if the system can't find the LAMMPS shared library or
|
|
one of the auxiliary shared libraries it depends on, or if something
|
|
about the library is incompatible with your Python. The error message
|
|
should give you an indication of what went wrong.
|
|
|
|
You can also test the load directly in Python as follows, without
|
|
first importing from the lammps.py file:
|
|
|
|
>>> from ctypes import CDLL
|
|
>>> CDLL("liblammps.so") :pre
|
|
|
|
If an error occurs, carefully go through the steps on the
|
|
"Build_basics"_Build_basics.html doc page about building a shared
|
|
library and the "Python_install"_Python_install.html doc page about
|
|
insuring Python can find the necessary two files it needs.
|
|
|
|
[Test LAMMPS and Python in serial:] :h4
|
|
|
|
To run a LAMMPS test in serial, type these lines into Python
|
|
interactively from the bench directory:
|
|
|
|
>>> from lammps import lammps
|
|
>>> lmp = lammps()
|
|
>>> lmp.file("in.lj") :pre
|
|
|
|
Or put the same lines in the file test.py and run it as
|
|
|
|
% python test.py :pre
|
|
|
|
Either way, you should see the results of running the in.lj benchmark
|
|
on a single processor appear on the screen, the same as if you had
|
|
typed something like:
|
|
|
|
lmp_g++ -in in.lj :pre
|
|
|
|
[Test LAMMPS and Python in parallel:] :h4
|
|
|
|
To run LAMMPS in parallel, assuming you have installed the
|
|
"PyPar"_https://github.com/daleroberts/pypar package as discussed
|
|
above, create a test.py file containing these lines:
|
|
|
|
import pypar
|
|
from lammps import lammps
|
|
lmp = lammps()
|
|
lmp.file("in.lj")
|
|
print "Proc %d out of %d procs has" % (pypar.rank(),pypar.size()),lmp
|
|
pypar.finalize() :pre
|
|
|
|
To run LAMMPS in parallel, assuming you have installed the
|
|
"mpi4py"_https://bitbucket.org/mpi4py/mpi4py package as discussed
|
|
above, create a test.py file containing these lines:
|
|
|
|
from mpi4py import MPI
|
|
from lammps import lammps
|
|
lmp = lammps()
|
|
lmp.file("in.lj")
|
|
me = MPI.COMM_WORLD.Get_rank()
|
|
nprocs = MPI.COMM_WORLD.Get_size()
|
|
print "Proc %d out of %d procs has" % (me,nprocs),lmp
|
|
MPI.Finalize() :pre
|
|
|
|
You can either script in parallel as:
|
|
|
|
% mpirun -np 4 python test.py :pre
|
|
|
|
and you should see the same output as if you had typed
|
|
|
|
% mpirun -np 4 lmp_g++ -in in.lj :pre
|
|
|
|
Note that if you leave out the 3 lines from test.py that specify PyPar
|
|
commands you will instantiate and run LAMMPS independently on each of
|
|
the P processors specified in the mpirun command. In this case you
|
|
should get 4 sets of output, each showing that a LAMMPS run was made
|
|
on a single processor, instead of one set of output showing that
|
|
LAMMPS ran on 4 processors. If the 1-processor outputs occur, it
|
|
means that PyPar is not working correctly.
|
|
|
|
Also note that once you import the PyPar module, PyPar initializes MPI
|
|
for you, and you can use MPI calls directly in your Python script, as
|
|
described in the PyPar documentation. The last line of your Python
|
|
script should be pypar.finalize(), to insure MPI is shut down
|
|
correctly.
|
|
|
|
[Running Python scripts:] :h4
|
|
|
|
Note that any Python script (not just for LAMMPS) can be invoked in
|
|
one of several ways:
|
|
|
|
% python foo.script
|
|
% python -i foo.script
|
|
% foo.script :pre
|
|
|
|
The last command requires that the first line of the script be
|
|
something like this:
|
|
|
|
#!/usr/local/bin/python
|
|
#!/usr/local/bin/python -i :pre
|
|
|
|
where the path points to where you have Python installed, and that you
|
|
have made the script file executable:
|
|
|
|
% chmod +x foo.script :pre
|
|
|
|
Without the "-i" flag, Python will exit when the script finishes.
|
|
With the "-i" flag, you will be left in the Python interpreter when
|
|
the script finishes, so you can type subsequent commands. As
|
|
mentioned above, you can only run Python interactively when running
|
|
Python on a single processor, not in parallel.
|