forked from lijiext/lammps
101 lines
4.4 KiB
HTML
101 lines
4.4 KiB
HTML
<HTML>
|
|
<CENTER><A HREF = "http://lammps.sandia.gov">LAMMPS WWW Site</A> - <A HREF = "Manual.html">LAMMPS Documentation</A> - <A HREF = "Section_commands.html#comm">LAMMPS Commands</A>
|
|
</CENTER>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
<HR>
|
|
|
|
<H3>replicate command
|
|
</H3>
|
|
<P><B>Syntax:</B>
|
|
</P>
|
|
<PRE>replicate nx ny nz
|
|
</PRE>
|
|
<UL><LI>nx,ny,nz = replication factors in each dimension
|
|
</UL>
|
|
<P><B>Examples:</B>
|
|
</P>
|
|
<PRE>replicate 2 3 2
|
|
</PRE>
|
|
<P><B>Description:</B>
|
|
</P>
|
|
<P>Replicate the current simulation one or more times in each dimension.
|
|
For example, replication factors of 2,2,2 will create a simulation
|
|
with 8x as many atoms by doubling the simulation domain in each
|
|
dimension. A replication factor of 1 in a dimension leaves the
|
|
simulation domain unchanged. When the new simulation box is created
|
|
it is also partitioned into a regular 3d grid of rectangular bricks,
|
|
one per processor, based on the number of processors being used and
|
|
the settings of the <A HREF = "processors.html">processors</A> command. The
|
|
partitioning can later be changed by the <A HREF = "balance.html">balance</A> or
|
|
<A HREF = "fix_balance.html">fix balance</A> commands.
|
|
</P>
|
|
<P>All properties of the atoms are replicated, including their
|
|
velocities, which may or may not be desirable. New atom IDs are
|
|
assigned to new atoms, as are molecule IDs. Bonds and other topology
|
|
interactions are created between pairs of new atoms as well as between
|
|
old and new atoms. This is done by using the image flag for each atom
|
|
to "unwrap" it out of the periodic box before replicating it.
|
|
</P>
|
|
<P>This means that any molecular bond you specify in the original data
|
|
file that crosses a periodic boundary should be between two atoms with
|
|
image flags that differ by 1. This will allow the bond to be
|
|
unwrapped appropriately.
|
|
</P>
|
|
<P><B>Restrictions:</B>
|
|
</P>
|
|
<P>A 2d simulation cannot be replicated in the z dimension.
|
|
</P>
|
|
<P>If a simulation is non-periodic in a dimension, care should be used
|
|
when replicating it in that dimension, as it may put atoms nearly on
|
|
top of each other.
|
|
</P>
|
|
<P>IMPORTANT NOTE: You cannot use the replicate command on a system which
|
|
has a molecule that spans the box and is bonded to itself across a
|
|
periodic boundary, so that the molecule is efffectively a loop. A
|
|
simple example would be a linear polymer chain that spans the
|
|
simulation box and bonds back to itself across the periodic boundary.
|
|
More realistic examples would be a CNT (meant to be an infinitely long
|
|
CNT) or a graphene sheet or a bulk periodic crystal where there are
|
|
explicit bonds specified between near neighbors. (Note that this only
|
|
applies to systems that have permanent bonds as specified in the data
|
|
file. A CNT that is just atoms modeled with the <A HREF = "pair_airebo.html">AIREBO
|
|
potential</A> has no such permanent bonds, so it can be
|
|
replicated.) The reason replication does not work with those systems
|
|
is that the image flag settings described above cannot be made
|
|
consistent. I.e. it is not possible to define images flags so that
|
|
when every pair of bonded atoms is unwrapped (using the image flags),
|
|
they will be close to each other. The only way the replicate command
|
|
could work in this scenario is for it to break a bond, insert more
|
|
atoms, and re-connect the loop for the larger simulation box. But it
|
|
is not clever enough to do this. So you will have to construct a
|
|
larger version of your molecule as a pre-processing step and input a
|
|
new data file to LAMMPS.
|
|
</P>
|
|
<P>If the current simulation was read in from a restart file (before a
|
|
run is performed), there can have been no fix information stored in
|
|
the file for individual atoms. Similarly, no fixes can be defined at
|
|
the time the replicate command is used that require vectors of atom
|
|
information to be stored. This is because the replicate command does
|
|
not know how to replicate that information for new atoms it creates.
|
|
</P>
|
|
<P>Replicating a system that has rigid bodies (defined via the <A HREF = "fix_rigid.html">fix
|
|
rigid</A> command), either currently defined or that
|
|
created the restart file which was read in before replicating, can
|
|
cause problems if there is a bond between a pair of rigid bodies that
|
|
straddle a periodic boundary. This is because the periodic image
|
|
information for particles in the rigid bodies are set differently than
|
|
for a non-rigid system and can result in a new bond being created that
|
|
spans the periodic box. Thus you cannot use the replicate command in
|
|
this scenario.
|
|
</P>
|
|
<P><B>Related commands:</B> none
|
|
</P>
|
|
<P><B>Default:</B> none
|
|
</P>
|
|
</HTML>
|