forked from lijiext/lammps
70 lines
2.5 KiB
HTML
70 lines
2.5 KiB
HTML
<HTML>
|
|
<CENTER><A HREF = "http://lammps.sandia.gov">LAMMPS WWW Site</A> - <A HREF = "Manual.html">LAMMPS Documentation</A> - <A HREF = "Section_commands.html#comm">LAMMPS Commands</A>
|
|
</CENTER>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
<HR>
|
|
|
|
<H3>write_restart command
|
|
</H3>
|
|
<P><B>Syntax:</B>
|
|
</P>
|
|
<PRE>write_restart file
|
|
</PRE>
|
|
<UL><LI>file = name of file to write restart information to
|
|
</UL>
|
|
<P><B>Examples:</B>
|
|
</P>
|
|
<PRE>write_restart restart.equil
|
|
write_restart poly.%.*
|
|
</PRE>
|
|
<P><B>Description:</B>
|
|
</P>
|
|
<P>Write a binary restart file of the current state of the simulation.
|
|
See the <A HREF = "read_restart.html">read_restart</A> command for information about
|
|
what is stored in a restart file.
|
|
</P>
|
|
<P>During a long simulation, the <A HREF = "restart.html">restart</A> command is
|
|
typically used to dump restart files periodically. The write_restart
|
|
command is useful after a minimization or whenever you wish to write
|
|
out a single current restart file.
|
|
</P>
|
|
<P>Similar to <A HREF = "dump.html">dump</A> files, the restart filename can contain
|
|
two wild-card characters. If a "*" appears in the filename, it is
|
|
replaced with the current timestep value. If a "%" character appears
|
|
in the filename, then one file is written by each processor and the
|
|
"%" character is replaced with the processor ID from 0 to P-1. An
|
|
additional file with the "%" replaced by "base" is also written, which
|
|
contains global information. For example, the files written for
|
|
filename restart.% would be restart.base, restart.0, restart.1, ...
|
|
restart.P-1. This creates smaller files and can be a fast mode of
|
|
output on parallel machines that support parallel I/O for output.
|
|
</P>
|
|
<P>Restart files can be read by a <A HREF = "read_restart.html">read_restart</A>
|
|
command to restart a simulation from a particular state. Because the
|
|
file is binary (to enable exact restarts), it may not be readable on
|
|
another machine. In this case, the restart2data program in the tools
|
|
directory can be used to convert a restart file to an ASCII data file.
|
|
Both the read_restart commmand and restart2data tool can read in a
|
|
restart file that was written with the "%" character so that multiple
|
|
files were created.
|
|
</P>
|
|
<P><B>Restrictions:</B>
|
|
</P>
|
|
<P>This command requires inter-processor communication to migrate atoms
|
|
before the restart file is written. This means that your system must
|
|
be ready to perform a simulation before using this command (force
|
|
fields setup, atom masses set, etc).
|
|
</P>
|
|
<P><B>Related commands:</B>
|
|
</P>
|
|
<P><A HREF = "restart.html">restart</A>, <A HREF = "read_restart.html">read_restart</A>
|
|
</P>
|
|
<P><B>Default:</B> none
|
|
</P>
|
|
</HTML>
|