forked from lijiext/lammps
91 lines
3.7 KiB
HTML
91 lines
3.7 KiB
HTML
<HTML>
|
|
<CENTER><A HREF = "http://lammps.sandia.gov">LAMMPS WWW Site</A> - <A HREF = "Manual.html">LAMMPS Documentation</A> - <A HREF = "Section_commands.html#comm">LAMMPS Commands</A>
|
|
</CENTER>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
<HR>
|
|
|
|
<H3>fix heat command
|
|
</H3>
|
|
<P><B>Syntax:</B>
|
|
</P>
|
|
<PRE>fix ID group-ID heat N eflux
|
|
</PRE>
|
|
<UL><LI>ID, group-ID are documented in <A HREF = "fix.html">fix</A> command
|
|
<LI>heat = style name of this fix command
|
|
<LI>N = add/subtract heat every this many timesteps
|
|
<LI>eflux = rate of heat addition or subtraction (energy/time units)
|
|
</UL>
|
|
<P><B>Examples:</B>
|
|
</P>
|
|
<PRE>fix 3 qin heat 1 1.0
|
|
fix 4 qout heat 1 -1.0
|
|
</PRE>
|
|
<P><B>Description:</B>
|
|
</P>
|
|
<P>Add non-translational kinetic energy (heat) to a group of atoms such
|
|
that their aggregate momentum is conserved. Two of these fixes can be
|
|
used to establish a temperature gradient across a simulation domain by
|
|
adding heat to one group of atoms (hot reservoir) and subtracting heat
|
|
from another (cold reservoir). E.g. a simulation sampling from the
|
|
McDLT ensemble. Note that the fix is applied to a group of atoms, not
|
|
a geometric region, so that the same set of atoms is affected wherever
|
|
they may move to.
|
|
</P>
|
|
<P>Heat addition/subtraction is performed every N timesteps. The <I>eflux</I>
|
|
parameter determines the change in aggregate energy of the entire
|
|
group of atoms per unit time, e.g. in eV/psec for <A HREF = "units.html">metal
|
|
units</A>. Thus it is an "extensive" quantity, meaning its
|
|
magnitude should be scaled with the number of atoms in the group.
|
|
Since <I>eflux</I> is independent of N or the <A HREF = "timestep.html">timestep</A>, a
|
|
larger value of N will add/subtract a larger amount of energy each
|
|
time the fix is invoked. If heat is subtracted from the system too
|
|
aggressively so that the group's kinetic energy would go to zero,
|
|
LAMMPS halts with an error message.
|
|
</P>
|
|
<P>Fix heat is different from a thermostat such as <A HREF = "fix_nvt.html">fix nvt</A>
|
|
or <A HREF = "fix_temp_rescale.html">fix temp/rescale</A> in that energy is
|
|
added/subtracted continually. Thus if there isn't another mechanism
|
|
in place to counterbalance this effect, the entire system will heat or
|
|
cool continuously. You can use multiple heat fixes so that the net
|
|
energy change is 0.0 or use <A HREF = "fix_viscous">fix viscous</A> to drain energy
|
|
from the system.
|
|
</P>
|
|
<P>This fix does not change the coordinates of its atoms; it only scales
|
|
their velocities. Thus you must still use an integration fix
|
|
(e.g. <A HREF = "fix_nve.html">fix nve</A>) on the affected atoms. This fix should
|
|
not normally be used on atoms that have their temperature controlled
|
|
by another fix - e.g. <A HREF = "fix_nvt.html">fix nvt</A> or <A HREF = "fix_langevin.html">fix
|
|
langevin</A> fix.
|
|
</P>
|
|
<P><B>Restart, fix_modify, output, run start/stop, minimize info:</B>
|
|
</P>
|
|
<P>No information about this fix is written to <A HREF = "restart.html">binary restart
|
|
files</A>. None of the <A HREF = "fix_modify.html">fix_modify</A> options
|
|
are relevant to this fix.
|
|
</P>
|
|
<P>This fix computes a scalar which can be accessed by various <A HREF = "Section_howto.html#4_15">output
|
|
commands</A>. This scalar is the most recent
|
|
value by which velocites were scaled. The scalar value calculated by
|
|
this fix is "intensive", meaning it is independent of the number of
|
|
atoms in the simulation.
|
|
</P>
|
|
<P>No parameter of this fix can be used with the <I>start/stop</I> keywords of
|
|
the <A HREF = "run.html">run</A> command. This fix is not invoked during <A HREF = "minimize.html">energy
|
|
minimization</A>.
|
|
</P>
|
|
<P><B>Restrictions:</B> none
|
|
</P>
|
|
<P><B>Related commands:</B>
|
|
</P>
|
|
<P><A HREF = "compute_temp.html">compute temp</A>, <A HREF = "compute_temp_region.html">compute
|
|
temp/region</A>
|
|
</P>
|
|
<P><B>Default:</B> none
|
|
</P>
|
|
</HTML>
|