forked from lijiext/lammps
155 lines
6.2 KiB
HTML
155 lines
6.2 KiB
HTML
<HTML>
|
|
<CENTER><A HREF = "http://lammps.sandia.gov">LAMMPS WWW Site</A> - <A HREF = "Manual.html">LAMMPS Documentation</A> - <A HREF = "Section_commands.html#comm">LAMMPS Commands</A>
|
|
</CENTER>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
<HR>
|
|
|
|
<H3>fix thermal/conductivity command
|
|
</H3>
|
|
<P><B>Syntax:</B>
|
|
</P>
|
|
<PRE>fix ID group-ID thermal/conductivity N edim Nbin keyword value ...
|
|
</PRE>
|
|
<UL><LI>ID, group-ID are documented in <A HREF = "fix.html">fix</A> command
|
|
|
|
<LI>thermal/conductivity = style name of this fix command
|
|
|
|
<LI>N = perform kinetic energy exchange every N steps
|
|
|
|
<LI>edim = <I>x</I> or <I>y</I> or <I>z</I> = direction of kinetic energy transfer
|
|
|
|
<LI>Nbin = # of layers in edim direction
|
|
|
|
<LI>zero or more keyword/value pairs may be appended
|
|
|
|
<LI>keyword = <I>swap</I>
|
|
|
|
<PRE> <I>swap</I> value = Nswap = number of swaps to perform every N steps
|
|
</PRE>
|
|
|
|
</UL>
|
|
<P><B>Examples:</B>
|
|
</P>
|
|
<PRE>fix 1 all thermal/conductivity 100 z 20
|
|
fix 1 all thermal/conductivity 50 z 20 swap 2
|
|
</PRE>
|
|
<P><B>Description:</B>
|
|
</P>
|
|
<P>Use the Muller-Plathe algorithm described in <A HREF = "#Muller-Plathe">this
|
|
paper</A> to exchange kinetic energy between two particles
|
|
in different regions of the simulation box every N steps. This
|
|
induces a temperature gradient in the system. As described below this
|
|
enables a thermal conductivity of the fluid to be calculated. This
|
|
algorithm is sometimes called a reverse non-equilibrium MD (reverse
|
|
NEMD) approach to computing thermal conductivity. This is because the
|
|
usual NEMD approach is to impose a temperature gradient on the system
|
|
and measure the response as the resulting heat flux. In the
|
|
Muller-Plathe method, the heat flux is imposed, and the temperature
|
|
gradient is the system's response.
|
|
</P>
|
|
<P>The simulation box is divided into <I>Nbin</I> layers in the <I>edim</I>
|
|
direction. Every N steps, Nswap pairs of atoms are chosen in the
|
|
following manner. Only atoms in the fix group are considered. The
|
|
hottest Nswap atoms in the bottom layer are selected. Similarly, the
|
|
coldest Nswap atoms in the middle later are selected. The two sets of
|
|
Nswap atoms are paired up and their velocities are exchanged. This
|
|
effectively swaps their kinetic energies, assuming their masses are
|
|
the same. Over time, this induces a temperature gradient in the
|
|
system which can be measured using commands such as the following,
|
|
which writes the temperature profile (assuming z = edim) to the file
|
|
tmp.profile:
|
|
</P>
|
|
<PRE>compute ke all ke/atom
|
|
variable temp atom c_ke<B></B>/1.5
|
|
fix 3 all ave/spatial 10 100 1000 z lower 0.05 v_temp &
|
|
file tmp.profile units reduced
|
|
</PRE>
|
|
<P>Note that by default, Nswap = 1, though this can be changed by the
|
|
optional <I>swap</I> keyword. Setting this parameter appropriately, in
|
|
conjunction with the swap rate N, allows the heat flux to be adjusted
|
|
across a wide range of values, and the kinetic energy to be exchanged
|
|
in large chunks or more smoothly.
|
|
</P>
|
|
<P>As described below, the total kinetic energy transferred by these
|
|
swaps is computed by the fix and can be output. Dividing this
|
|
quantity by time and the cross-sectional area of the simulation box
|
|
yields a heat flux. The ratio of heat flux to the slope of the
|
|
temperature profile is the thermal conductivity of the fluid,
|
|
in appopriate units. See the <A HREF = "#Muller-Plathe">Muller-Plathe paper</A> for
|
|
details.
|
|
</P>
|
|
<P>IMPORTANT NOTE: After equilibration, if the temperature gradient you
|
|
observe is not linear, then you are likely swapping energy too
|
|
frequently and are not in a regime of linear response. In this case
|
|
you cannot accurately infer a thermal conductivity and should try
|
|
increasing the Nevery parameter.
|
|
</P>
|
|
<P><B>Restart, fix_modify, output, run start/stop, minimize info:</B>
|
|
</P>
|
|
<P>No information about this fix is written to <A HREF = "restart.html">binary restart
|
|
files</A>. None of the <A HREF = "fix_modify.html">fix_modify</A> options
|
|
are relevant to this fix.
|
|
</P>
|
|
<P>The cummulative kinetic energy transferred between the bottom and
|
|
middle of the simulation box (in the <I>edim</I> direction) is stored as a
|
|
scalar quantity by this fix. This quantity is zeroed when the fix is
|
|
defined and accumlates thereafter, once every N steps. The units of
|
|
the quantity are energy; see the <A HREF = "units.html">units</A> command for
|
|
details. This quantity can be accessed by various <A HREF = "Section_howto.html#4_15">output
|
|
commands</A>, such as <A HREF = "thermo_style.html">thermo_style
|
|
custom</A>. The scalar value calculated by this fix is
|
|
"intensive", meaning it is independent of the number of atoms in the
|
|
simulation.
|
|
</P>
|
|
<P>No parameter of this fix can be used with the <I>start/stop</I> keywords of
|
|
the <A HREF = "run.html">run</A> command. This fix is not invoked during <A HREF = "minimize.html">energy
|
|
minimization</A>.
|
|
</P>
|
|
<P><B>Restrictions:</B>
|
|
</P>
|
|
<P>LAMMPS does not check, but the masses of all exchanged atom pairs
|
|
should be the same to use this fix in a way that conserves both
|
|
momentum and kinetic energy. Thus you should not need to thermostat
|
|
the system. If you do use a thermostat, you may want to apply it only
|
|
to the non-swapped dimensions (other than <I>vdim</I>).
|
|
</P>
|
|
<P>LAMMPS does not check, but you should not use this fix to swap the
|
|
kinetic energy of atoms that are in constrained molecules, e.g. via
|
|
<A HREF = "fix_shake.html">fix shake</A> or <A HREF = "fix_rigid.html">fix rigid</A>. This is
|
|
because application of the constraints will alter the amount of
|
|
transferred momentum. You should, however, be able to use flexible
|
|
molecules. See the <A HREF = "#Zhang">Zhang paper</A> for a discussion and results
|
|
of this idea.
|
|
</P>
|
|
<P>When running a simulation with large, massive particles or molecules
|
|
in a background solvent, you may want to only exchange kinetic energy
|
|
bewteen solvent particles.
|
|
</P>
|
|
<P><B>Related commands:</B>
|
|
</P>
|
|
<P><A HREF = "fix_ave_spatial.html">fix ave/spatial</A>, <A HREF = "fix_viscosity.html">fix
|
|
viscosity</A>
|
|
</P>
|
|
<P><B>Default:</B>
|
|
</P>
|
|
<P>The option defaults are swap = 1.
|
|
</P>
|
|
<HR>
|
|
|
|
<A NAME = "Muller-Plathe"></A>
|
|
|
|
<P><B>(Muller-Plathe)</B> Muller-Plathe and Reith, Computational and
|
|
Theoretical Polymer Science, 9, 203-209 (1999).
|
|
</P>
|
|
<A NAME = "Zhang"></A>
|
|
|
|
<P><B>(Zhang)</B> Zhang, Lussetti, de Souza, Muller-Plathe, J Phys Chem B,
|
|
109, 15060-15067 (2005).
|
|
</P>
|
|
</HTML>
|