2007-09-06 00:05:47 +08:00
|
|
|
<HTML>
|
|
|
|
|
<CENTER><A HREF = "http://lammps.sandia.gov">LAMMPS WWW Site</A> - <A HREF = "Manual.html">LAMMPS Documentation</A> - <A HREF = "Section_commands.html#comm">LAMMPS Commands</A>
|
|
|
|
|
</CENTER>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
<HR>
|
|
|
|
|
|
|
|
|
|
<H3>fix nve/limit command
|
|
|
|
|
</H3>
|
|
|
|
|
<P><B>Syntax:</B>
|
|
|
|
|
</P>
|
|
|
|
|
<PRE>fix ID group-ID nve/limit xmax
|
|
|
|
|
</PRE>
|
|
|
|
|
<UL><LI>ID, group-ID are documented in <A HREF = "fix.html">fix</A> command
|
|
|
|
|
<LI>nve = style name of this fix command
|
|
|
|
|
<LI>xmax = maximum distance an atom can move in one timestep (distance units)
|
|
|
|
|
</UL>
|
|
|
|
|
<P><B>Examples:</B>
|
|
|
|
|
</P>
|
|
|
|
|
<PRE>fix 1 all nve/limit 0.1
|
|
|
|
|
</PRE>
|
|
|
|
|
<P><B>Description:</B>
|
|
|
|
|
</P>
|
|
|
|
|
<P>Perform constant NVE updates of position and velocity for atoms in the
|
|
|
|
|
group each timestep. A limit is imposed on the maximum distance an
|
|
|
|
|
atom can move in one timestep. This is useful when starting a
|
|
|
|
|
simulation with a configuration containing highly overlapped atoms.
|
|
|
|
|
Normally this would generate huge forces which would blow atoms out of
|
|
|
|
|
the simulation box, causing LAMMPS to stop with an error.
|
|
|
|
|
</P>
|
|
|
|
|
<P>Using this fix can overcome that problem. Forces on atoms must still
|
|
|
|
|
be computable (which typically means 2 atoms must have a separation
|
|
|
|
|
distance > 0.0). But large velocities generated by large forces are
|
|
|
|
|
reset to a value that corresponds to a displacement of length <I>xmax</I>
|
|
|
|
|
in a single timestep. <I>Xmax</I> is specified in distance units; see the
|
|
|
|
|
<A HREF = "units.html">units</A> command for details. The value of <I>xmax</I> should be
|
|
|
|
|
consistent with the neighbor skin distance and the frequency of
|
|
|
|
|
neighbor list re-building, so that pairwise interactions are not
|
|
|
|
|
missed on successive timesteps as atoms move. See the
|
|
|
|
|
<A HREF = "neighbor.html">neighbor</A> and <A HREF = "neigh_modify.html">neigh_modify</A> commands
|
|
|
|
|
for details.
|
|
|
|
|
</P>
|
|
|
|
|
<P>Note that if a velocity reset occurs the integrator will not conserve
|
|
|
|
|
energy. On steps where no velocity resets occur, this integrator is
|
|
|
|
|
exactly like the <A HREF = "fix_nve.html">fix nve</A> command. Since forces are
|
|
|
|
|
unaltered, pressures computed by thermodynamic output will still be
|
|
|
|
|
very large for overlapped configurations.
|
|
|
|
|
</P>
|
2007-10-11 06:28:11 +08:00
|
|
|
<P><B>Restart, fix_modify, output, run start/stop, minimize info:</B>
|
2007-09-06 00:05:47 +08:00
|
|
|
</P>
|
|
|
|
|
<P>No information about this fix is written to <A HREF = "restart.html">binary restart
|
|
|
|
|
files</A>. None of the <A HREF = "fix_modify.html">fix_modify</A> options
|
2008-01-03 08:29:17 +08:00
|
|
|
are relevant to this fix.
|
|
|
|
|
</P>
|
2010-04-03 00:51:06 +08:00
|
|
|
<P>This fix computes a global scalar which can be accessed by various
|
2011-08-26 01:01:01 +08:00
|
|
|
<A HREF = "Section_howto.html#howto_15">output commands</A>. The scalar is the
|
|
|
|
|
count of how many updates of atom's velocity/position were limited by
|
|
|
|
|
the maximum distance criterion. This should be roughly the number of
|
2010-04-03 00:51:06 +08:00
|
|
|
atoms so affected, except that updates occur at both the beginning and
|
|
|
|
|
end of a timestep in a velocity Verlet timestepping algorithm. This
|
|
|
|
|
is a cumulative quantity for the current run, but is re-initialized to
|
|
|
|
|
zero each time a run is performed. The scalar value calculated by
|
|
|
|
|
this fix is "extensive".
|
2008-01-03 08:29:17 +08:00
|
|
|
</P>
|
|
|
|
|
<P>No parameter of this fix can be used with the <I>start/stop</I> keywords of
|
|
|
|
|
the <A HREF = "run.html">run</A> command. This fix is not invoked during <A HREF = "minimize.html">energy
|
|
|
|
|
minimization</A>.
|
2007-09-06 00:05:47 +08:00
|
|
|
</P>
|
|
|
|
|
<P><B>Restrictions:</B> none
|
|
|
|
|
</P>
|
|
|
|
|
<P><B>Related commands:</B>
|
|
|
|
|
</P>
|
|
|
|
|
<P><A HREF = "fix_nve.html">fix nve</A>, <A HREF = "fix_nve_noforce.html">fix nve/noforce</A>,
|
|
|
|
|
<A HREF = "pair_soft.html">pair_style soft</A>
|
|
|
|
|
</P>
|
|
|
|
|
<P><B>Default:</B> none
|
|
|
|
|
</P>
|
|
|
|
|
</HTML>
|
