linux-sg2042/drivers/bluetooth/btmrvl_sdio.h

109 lines
3.0 KiB
C

/**
* Marvell BT-over-SDIO driver: SDIO interface related definitions
*
* Copyright (C) 2009, Marvell International Ltd.
*
* This software file (the "File") is distributed by Marvell International
* Ltd. under the terms of the GNU General Public License Version 2, June 1991
* (the "License"). You may use, redistribute and/or modify this File in
* accordance with the terms and conditions of the License, a copy of which
* is available by writing to the Free Software Foundation, Inc.,
* 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA or on the
* worldwide web at http://www.gnu.org/licenses/old-licenses/gpl-2.0.txt.
*
*
* THE FILE IS DISTRIBUTED AS-IS, WITHOUT WARRANTY OF ANY KIND, AND THE
* IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
* ARE EXPRESSLY DISCLAIMED. The License provides additional details about
* this warranty disclaimer.
*
**/
#define SDIO_HEADER_LEN 4
/* SD block size can not bigger than 64 due to buf size limit in firmware */
/* define SD block size for data Tx/Rx */
#define SDIO_BLOCK_SIZE 64
/* Number of blocks for firmware transfer */
#define FIRMWARE_TRANSFER_NBLOCK 2
/* This is for firmware specific length */
#define FW_EXTRA_LEN 36
#define MRVDRV_SIZE_OF_CMD_BUFFER (2 * 1024)
#define MRVDRV_BT_RX_PACKET_BUFFER_SIZE \
(HCI_MAX_FRAME_SIZE + FW_EXTRA_LEN)
#define ALLOC_BUF_SIZE (((max_t (int, MRVDRV_BT_RX_PACKET_BUFFER_SIZE, \
MRVDRV_SIZE_OF_CMD_BUFFER) + SDIO_HEADER_LEN \
+ SDIO_BLOCK_SIZE - 1) / SDIO_BLOCK_SIZE) \
* SDIO_BLOCK_SIZE)
/* The number of times to try when polling for status */
#define MAX_POLL_TRIES 100
/* Max retry number of CMD53 write */
#define MAX_WRITE_IOMEM_RETRY 2
/* Host Control Registers */
#define IO_PORT_0_REG 0x00
#define IO_PORT_1_REG 0x01
#define IO_PORT_2_REG 0x02
#define CONFIG_REG 0x03
#define HOST_POWER_UP BIT(1)
#define HOST_CMD53_FIN BIT(2)
#define HOST_INT_MASK_REG 0x04
#define HIM_DISABLE 0xff
#define HIM_ENABLE (BIT(0) | BIT(1))
#define HOST_INTSTATUS_REG 0x05
#define UP_LD_HOST_INT_STATUS BIT(0)
#define DN_LD_HOST_INT_STATUS BIT(1)
/* Card Control Registers */
#define SQ_READ_BASE_ADDRESS_A0_REG 0x10
#define SQ_READ_BASE_ADDRESS_A1_REG 0x11
#define CARD_STATUS_REG 0x20
#define DN_LD_CARD_RDY BIT(0)
#define CARD_IO_READY BIT(3)
#define CARD_FW_STATUS0_REG 0x40
#define CARD_FW_STATUS1_REG 0x41
#define FIRMWARE_READY 0xfedc
#define CARD_RX_LEN_REG 0x42
#define CARD_RX_UNIT_REG 0x43
struct btmrvl_sdio_card {
struct sdio_func *func;
u32 ioport;
const char *helper;
const char *firmware;
u8 rx_unit;
struct btmrvl_private *priv;
};
struct btmrvl_sdio_device {
const char *helper;
const char *firmware;
};
/* Platform specific DMA alignment */
#define BTSDIO_DMA_ALIGN 8
/* Macros for Data Alignment : size */
#define ALIGN_SZ(p, a) \
(((p) + ((a) - 1)) & ~((a) - 1))
/* Macros for Data Alignment : address */
#define ALIGN_ADDR(p, a) \
((((unsigned long)(p)) + (((unsigned long)(a)) - 1)) & \
~(((unsigned long)(a)) - 1))