cdcdbbf350
* Silk board with R-Car E2 (r8a7794) SoC
- Add r1ex24002 EEPROM to DT
Magnus Damm says "Extend the Silk board support to include U14 which is
an I2C based EEPROM hooked up to the I2C1 bus."
- Add GPIO keys to DT
Magnus Damm says "Extend the Silk board support to include SW3, SW4,
SW6 and SW12. They are all connected via GPIO lines and handled by the
gpio-keys driver"
* Marzen board with R-Car H1 (r7a7779) SoC
- Add SDHI0 VCCQ Regulator
Magnus Damm says "Add support for the on-board voltage regulator hooked
up to GPIO3_20 on r8a7779 Marzen. The board schematics describes the
regulator as U4 TPS2110A. Input wise, U4 has D0 fixed to ground, D1
tied to GPIO3_20 while IN1 is fixed to 3.3V and IN2 is fixed to 1.8V.
OUT goes to the pull-ups for the data pins of SDHI0."
* Porter board with R-Car M3W (r8a7791) SoC
- Fix HDMI output routing
Laurent Pinchart says "The HDMI encoder is connected to the RGB output
of the DU, which is port@0, not port@1."
* iWave Systems RZ/G1E SODIMM System On Module (iW-RainboW-G22M-SM) and
iWave Systems RZ/G1M Qseven System On Module (iW-RainboW-G20M-Qseven)
- Enable cmt0
* Stout board with R-Car H2 (r8a7790) SoC
- Initial support
* Lager board with R-Car H2 (r8a7790) SoC
- Add CEC clock for HDMI transmitter
Niklas Söderlund says "The adv7511 on the Lager board has a 12 MHz
fixed clock for the CEC block. Specify this in the dts to enable CEC
support."
- Move cec_clock to root node
By definition nodes without a bus address do not belong on the bus
* kzm9d board with EMMA Mobile EV2 (EMEV2) SoC
- Fix "debounce-interval" property misspelling
* RZ/G1M (r8a7743) and RZ/G1H (r8a7745) SoCs
- Add IPMMU DT nodes
- Add VSP support
* R-Car Gen2 boards
- Use I2C demuxer for
This allows run-time switching between alternate I2C IP blocks
* R-Car Gen2 and RZ/G1 SoCs
- Clean up DT files to ease future maintenance
+ add soc node for IP attached to the bus
+ sort subnodes of soc and root node
+ consistently use single space after =
* R-Car H2 (r8a7790), M3-W (r8a7791) and M3-N (r7a7793) SoCs
- Reduce size of thermal registers
According to the "User's Manual: Hardware" v2.00 the registers at base
0xe61f0000 extend to an offset of 0x10, rather than 0x14 which is the
case on the r8a73a4 (R-Mobile APE6).
This should not have any runtime affect as mapping granularity is
PAGE_SIZE.
-----BEGIN PGP SIGNATURE-----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=dZnw
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Renesas ARM Based SoC DT Updates for v4.17" from Simon Horman:
* Silk board with R-Car E2 (r8a7794) SoC
- Add r1ex24002 EEPROM to DT
Magnus Damm says "Extend the Silk board support to include U14 which is
an I2C based EEPROM hooked up to the I2C1 bus."
- Add GPIO keys to DT
Magnus Damm says "Extend the Silk board support to include SW3, SW4,
SW6 and SW12. They are all connected via GPIO lines and handled by the
gpio-keys driver"
* Marzen board with R-Car H1 (r7a7779) SoC
- Add SDHI0 VCCQ Regulator
Magnus Damm says "Add support for the on-board voltage regulator hooked
up to GPIO3_20 on r8a7779 Marzen. The board schematics describes the
regulator as U4 TPS2110A. Input wise, U4 has D0 fixed to ground, D1
tied to GPIO3_20 while IN1 is fixed to 3.3V and IN2 is fixed to 1.8V.
OUT goes to the pull-ups for the data pins of SDHI0."
* Porter board with R-Car M3W (r8a7791) SoC
- Fix HDMI output routing
Laurent Pinchart says "The HDMI encoder is connected to the RGB output
of the DU, which is port@0, not port@1."
* iWave Systems RZ/G1E SODIMM System On Module (iW-RainboW-G22M-SM) and
iWave Systems RZ/G1M Qseven System On Module (iW-RainboW-G20M-Qseven)
- Enable cmt0
* Stout board with R-Car H2 (r8a7790) SoC
- Initial support
* Lager board with R-Car H2 (r8a7790) SoC
- Add CEC clock for HDMI transmitter
Niklas Söderlund says "The adv7511 on the Lager board has a 12 MHz
fixed clock for the CEC block. Specify this in the dts to enable CEC
support."
- Move cec_clock to root node
By definition nodes without a bus address do not belong on the bus
* kzm9d board with EMMA Mobile EV2 (EMEV2) SoC
- Fix "debounce-interval" property misspelling
* RZ/G1M (r8a7743) and RZ/G1H (r8a7745) SoCs
- Add IPMMU DT nodes
- Add VSP support
* R-Car Gen2 boards
- Use I2C demuxer for
This allows run-time switching between alternate I2C IP blocks
* R-Car Gen2 and RZ/G1 SoCs
- Clean up DT files to ease future maintenance
+ add soc node for IP attached to the bus
+ sort subnodes of soc and root node
+ consistently use single space after =
* R-Car H2 (r8a7790), M3-W (r8a7791) and M3-N (r7a7793) SoCs
- Reduce size of thermal registers
According to the "User's Manual: Hardware" v2.00 the registers at base
0xe61f0000 extend to an offset of 0x10, rather than 0x14 which is the
case on the r8a73a4 (R-Mobile APE6).
This should not have any runtime affect as mapping granularity is
PAGE_SIZE.
* tag 'renesas-dt-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (47 commits)
ARM: dts: silk: Add GPIO keys to DT
ARM: dts: silk: Add r1ex24002 EEPROM to DT
ARM: dts: marzen: Add SDHI0 VCCQ Regulator
ARM: dts: stout: Initial r8a7790 Stout board support
ARM: dts: lager: Move cec_clock to root node
ARM: dts: kzm9d: Fix "debounce-interval" property misspelling
ARM: dts: gose: use demuxer for I2C4
ARM: dts: gose: use demuxer for I2C2
ARM: dts: silk: use demuxer for I2C1
ARM: dts: alt: use demuxer for I2C1
ARM: dts: porter: use demuxer for I2C2
ARM: dts: koelsch: use demuxer for I2C4
ARM: dts: koelsch: use demuxer for I2C2
ARM: dts: lager: use demuxer for IIC3/I2C3
ARM: dts: lager: use demuxer for IIC2/I2C2
ARM: dts: r8a7745: Add VSP support
ARM: dts: r8a7743: Add VSP support
ARM: dts: r8a7745: Add IPMMU DT nodes
ARM: dts: r8a7743: Add IPMMU DT nodes
ARM: dts: r8a7745: sort subnodes of soc node
...
|
||
|---|---|---|
| Documentation | ||
| LICENSES | ||
| arch | ||
| block | ||
| certs | ||
| crypto | ||
| drivers | ||
| firmware | ||
| fs | ||
| include | ||
| init | ||
| ipc | ||
| kernel | ||
| lib | ||
| mm | ||
| net | ||
| samples | ||
| scripts | ||
| security | ||
| sound | ||
| tools | ||
| usr | ||
| virt | ||
| .cocciconfig | ||
| .get_maintainer.ignore | ||
| .gitattributes | ||
| .gitignore | ||
| .mailmap | ||
| COPYING | ||
| CREDITS | ||
| Kbuild | ||
| Kconfig | ||
| MAINTAINERS | ||
| Makefile | ||
| README | ||
README
Linux kernel ============ This file was moved to Documentation/admin-guide/README.rst Please notice that there are several guides for kernel developers and users. These guides can be rendered in a number of formats, like HTML and PDF. In order to build the documentation, use ``make htmldocs`` or ``make pdfdocs``. There are various text files in the Documentation/ subdirectory, several of them using the Restructured Text markup notation. See Documentation/00-INDEX for a list of what is contained in each file. Please read the Documentation/process/changes.rst file, as it contains the requirements for building and running the kernel, and information about the problems which may result by upgrading your kernel.