93 lines
2.5 KiB
Plaintext
93 lines
2.5 KiB
Plaintext
* NI XGE Ethernet controller
|
|
|
|
Required properties:
|
|
- compatible: Should be "ni,xge-enet-3.00", but can be "ni,xge-enet-2.00" for
|
|
older device trees with DMA engines co-located in the address map,
|
|
with the one reg entry to describe the whole device.
|
|
- reg: Address and length of the register set for the device. It contains the
|
|
information of registers in the same order as described by reg-names.
|
|
- reg-names: Should contain the reg names
|
|
"dma": DMA engine control and status region
|
|
"ctrl": MDIO and PHY control and status region
|
|
- interrupts: Should contain tx and rx interrupt
|
|
- interrupt-names: Should be "rx" and "tx"
|
|
- phy-mode: See ethernet.txt file in the same directory.
|
|
- nvmem-cells: Phandle of nvmem cell containing the MAC address
|
|
- nvmem-cell-names: Should be "address"
|
|
|
|
Optional properties:
|
|
- mdio subnode to indicate presence of MDIO controller
|
|
- fixed-link : Assume a fixed link. See fixed-link.txt in the same directory.
|
|
Use instead of phy-handle.
|
|
- phy-handle: See ethernet.txt file in the same directory.
|
|
|
|
Examples (10G generic PHY):
|
|
nixge0: ethernet@40000000 {
|
|
compatible = "ni,xge-enet-3.00";
|
|
reg = <0x40000000 0x4000
|
|
0x41002000 0x2000>;
|
|
reg-names = "dma", "ctrl";
|
|
|
|
nvmem-cells = <ð1_addr>;
|
|
nvmem-cell-names = "address";
|
|
|
|
interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>, <0 30 IRQ_TYPE_LEVEL_HIGH>;
|
|
interrupt-names = "rx", "tx";
|
|
interrupt-parent = <&intc>;
|
|
|
|
phy-mode = "xgmii";
|
|
phy-handle = <ðernet_phy1>;
|
|
|
|
mdio {
|
|
ethernet_phy1: ethernet-phy@4 {
|
|
compatible = "ethernet-phy-ieee802.3-c45";
|
|
reg = <4>;
|
|
};
|
|
};
|
|
};
|
|
|
|
Examples (10G generic PHY, no MDIO):
|
|
nixge0: ethernet@40000000 {
|
|
compatible = "ni,xge-enet-2.00";
|
|
reg = <0x40000000 0x6000>;
|
|
|
|
nvmem-cells = <ð1_addr>;
|
|
nvmem-cell-names = "address";
|
|
|
|
interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>, <0 30 IRQ_TYPE_LEVEL_HIGH>;
|
|
interrupt-names = "rx", "tx";
|
|
interrupt-parent = <&intc>;
|
|
|
|
phy-mode = "xgmii";
|
|
phy-handle = <ðernet_phy1>;
|
|
};
|
|
|
|
Examples (1G generic fixed-link + MDIO):
|
|
nixge0: ethernet@40000000 {
|
|
compatible = "ni,xge-enet-2.00";
|
|
reg = <0x40000000 0x6000>;
|
|
|
|
nvmem-cells = <ð1_addr>;
|
|
nvmem-cell-names = "address";
|
|
|
|
interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>, <0 30 IRQ_TYPE_LEVEL_HIGH>;
|
|
interrupt-names = "rx", "tx";
|
|
interrupt-parent = <&intc>;
|
|
|
|
phy-mode = "xgmii";
|
|
|
|
fixed-link {
|
|
speed = <1000>;
|
|
pause;
|
|
link-gpios = <&gpio0 63 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
mdio {
|
|
ethernet_phy1: ethernet-phy@4 {
|
|
compatible = "ethernet-phy-ieee802.3-c22";
|
|
reg = <4>;
|
|
};
|
|
};
|
|
|
|
};
|