79 lines
3.1 KiB
Plaintext
79 lines
3.1 KiB
Plaintext
MediaTek DWMAC glue layer controller
|
|
|
|
This file documents platform glue layer for stmmac.
|
|
Please see stmmac.txt for the other unchanged properties.
|
|
|
|
The device node has following properties.
|
|
|
|
Required properties:
|
|
- compatible: Should be "mediatek,mt2712-gmac" for MT2712 SoC
|
|
- reg: Address and length of the register set for the device
|
|
- interrupts: Should contain the MAC interrupts
|
|
- interrupt-names: Should contain a list of interrupt names corresponding to
|
|
the interrupts in the interrupts property, if available.
|
|
Should be "macirq" for the main MAC IRQ
|
|
- clocks: Must contain a phandle for each entry in clock-names.
|
|
- clock-names: The name of the clock listed in the clocks property. These are
|
|
"axi", "apb", "mac_main", "ptp_ref" for MT2712 SoC
|
|
- mac-address: See ethernet.txt in the same directory
|
|
- phy-mode: See ethernet.txt in the same directory
|
|
- mediatek,pericfg: A phandle to the syscon node that control ethernet
|
|
interface and timing delay.
|
|
|
|
Optional properties:
|
|
- mediatek,tx-delay-ps: TX clock delay macro value. Default is 0.
|
|
It should be defined for RGMII/MII interface.
|
|
- mediatek,rx-delay-ps: RX clock delay macro value. Default is 0.
|
|
It should be defined for RGMII/MII/RMII interface.
|
|
Both delay properties need to be a multiple of 170 for RGMII interface,
|
|
or will round down. Range 0~31*170.
|
|
Both delay properties need to be a multiple of 550 for MII/RMII interface,
|
|
or will round down. Range 0~31*550.
|
|
|
|
- mediatek,rmii-rxc: boolean property, if present indicates that the RMII
|
|
reference clock, which is from external PHYs, is connected to RXC pin
|
|
on MT2712 SoC.
|
|
Otherwise, is connected to TXC pin.
|
|
- mediatek,txc-inverse: boolean property, if present indicates that
|
|
1. tx clock will be inversed in MII/RGMII case,
|
|
2. tx clock inside MAC will be inversed relative to reference clock
|
|
which is from external PHYs in RMII case, and it rarely happen.
|
|
- mediatek,rxc-inverse: boolean property, if present indicates that
|
|
1. rx clock will be inversed in MII/RGMII case.
|
|
2. reference clock will be inversed when arrived at MAC in RMII case.
|
|
- assigned-clocks: mac_main and ptp_ref clocks
|
|
- assigned-clock-parents: parent clocks of the assigned clocks
|
|
|
|
Example:
|
|
eth: ethernet@1101c000 {
|
|
compatible = "mediatek,mt2712-gmac";
|
|
reg = <0 0x1101c000 0 0x1300>;
|
|
interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_LOW>;
|
|
interrupt-names = "macirq";
|
|
phy-mode ="rgmii";
|
|
mac-address = [00 55 7b b5 7d f7];
|
|
clock-names = "axi",
|
|
"apb",
|
|
"mac_main",
|
|
"ptp_ref",
|
|
"ptp_top";
|
|
clocks = <&pericfg CLK_PERI_GMAC>,
|
|
<&pericfg CLK_PERI_GMAC_PCLK>,
|
|
<&topckgen CLK_TOP_ETHER_125M_SEL>,
|
|
<&topckgen CLK_TOP_ETHER_50M_SEL>;
|
|
assigned-clocks = <&topckgen CLK_TOP_ETHER_125M_SEL>,
|
|
<&topckgen CLK_TOP_ETHER_50M_SEL>;
|
|
assigned-clock-parents = <&topckgen CLK_TOP_ETHERPLL_125M>,
|
|
<&topckgen CLK_TOP_APLL1_D3>;
|
|
mediatek,pericfg = <&pericfg>;
|
|
mediatek,tx-delay-ps = <1530>;
|
|
mediatek,rx-delay-ps = <1530>;
|
|
mediatek,rmii-rxc;
|
|
mediatek,txc-inverse;
|
|
mediatek,rxc-inverse;
|
|
snps,txpbl = <32>;
|
|
snps,rxpbl = <32>;
|
|
snps,reset-gpio = <&pio 87 GPIO_ACTIVE_LOW>;
|
|
snps,reset-active-low;
|
|
};
|