linux-sg2042/arch/arm/mach-msm/proc_comm.h

259 lines
7.1 KiB
C

/* arch/arm/mach-msm/proc_comm.h
*
* Copyright (c) 2007 QUALCOMM Incorporated
*
* This software is licensed under the terms of the GNU General Public
* License version 2, as published by the Free Software Foundation, and
* may be copied, distributed, and modified under those terms.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
*/
#ifndef _ARCH_ARM_MACH_MSM_PROC_COMM_H_
#define _ARCH_ARM_MACH_MSM_PROC_COMM_H_
#include <linux/init.h>
enum {
PCOM_CMD_IDLE = 0x0,
PCOM_CMD_DONE,
PCOM_RESET_APPS,
PCOM_RESET_CHIP,
PCOM_CONFIG_NAND_MPU,
PCOM_CONFIG_USB_CLKS,
PCOM_GET_POWER_ON_STATUS,
PCOM_GET_WAKE_UP_STATUS,
PCOM_GET_BATT_LEVEL,
PCOM_CHG_IS_CHARGING,
PCOM_POWER_DOWN,
PCOM_USB_PIN_CONFIG,
PCOM_USB_PIN_SEL,
PCOM_SET_RTC_ALARM,
PCOM_NV_READ,
PCOM_NV_WRITE,
PCOM_GET_UUID_HIGH,
PCOM_GET_UUID_LOW,
PCOM_GET_HW_ENTROPY,
PCOM_RPC_GPIO_TLMM_CONFIG_REMOTE,
PCOM_CLKCTL_RPC_ENABLE,
PCOM_CLKCTL_RPC_DISABLE,
PCOM_CLKCTL_RPC_RESET,
PCOM_CLKCTL_RPC_SET_FLAGS,
PCOM_CLKCTL_RPC_SET_RATE,
PCOM_CLKCTL_RPC_MIN_RATE,
PCOM_CLKCTL_RPC_MAX_RATE,
PCOM_CLKCTL_RPC_RATE,
PCOM_CLKCTL_RPC_PLL_REQUEST,
PCOM_CLKCTL_RPC_ENABLED,
PCOM_VREG_SWITCH,
PCOM_VREG_SET_LEVEL,
PCOM_GPIO_TLMM_CONFIG_GROUP,
PCOM_GPIO_TLMM_UNCONFIG_GROUP,
PCOM_NV_WRITE_BYTES_4_7,
PCOM_CONFIG_DISP,
PCOM_GET_FTM_BOOT_COUNT,
PCOM_RPC_GPIO_TLMM_CONFIG_EX,
PCOM_PM_MPP_CONFIG,
PCOM_GPIO_IN,
PCOM_GPIO_OUT,
PCOM_RESET_MODEM,
PCOM_RESET_CHIP_IMM,
PCOM_PM_VID_EN,
PCOM_VREG_PULLDOWN,
PCOM_GET_MODEM_VERSION,
PCOM_CLK_REGIME_SEC_RESET,
PCOM_CLK_REGIME_SEC_RESET_ASSERT,
PCOM_CLK_REGIME_SEC_RESET_DEASSERT,
PCOM_CLK_REGIME_SEC_PLL_REQUEST_WRP,
PCOM_CLK_REGIME_SEC_ENABLE,
PCOM_CLK_REGIME_SEC_DISABLE,
PCOM_CLK_REGIME_SEC_IS_ON,
PCOM_CLK_REGIME_SEC_SEL_CLK_INV,
PCOM_CLK_REGIME_SEC_SEL_CLK_SRC,
PCOM_CLK_REGIME_SEC_SEL_CLK_DIV,
PCOM_CLK_REGIME_SEC_ICODEC_CLK_ENABLE,
PCOM_CLK_REGIME_SEC_ICODEC_CLK_DISABLE,
PCOM_CLK_REGIME_SEC_SEL_SPEED,
PCOM_CLK_REGIME_SEC_CONFIG_GP_CLK_WRP,
PCOM_CLK_REGIME_SEC_CONFIG_MDH_CLK_WRP,
PCOM_CLK_REGIME_SEC_USB_XTAL_ON,
PCOM_CLK_REGIME_SEC_USB_XTAL_OFF,
PCOM_CLK_REGIME_SEC_SET_QDSP_DME_MODE,
PCOM_CLK_REGIME_SEC_SWITCH_ADSP_CLK,
PCOM_CLK_REGIME_SEC_GET_MAX_ADSP_CLK_KHZ,
PCOM_CLK_REGIME_SEC_GET_I2C_CLK_KHZ,
PCOM_CLK_REGIME_SEC_MSM_GET_CLK_FREQ_KHZ,
PCOM_CLK_REGIME_SEC_SEL_VFE_SRC,
PCOM_CLK_REGIME_SEC_MSM_SEL_CAMCLK,
PCOM_CLK_REGIME_SEC_MSM_SEL_LCDCLK,
PCOM_CLK_REGIME_SEC_VFE_RAIL_OFF,
PCOM_CLK_REGIME_SEC_VFE_RAIL_ON,
PCOM_CLK_REGIME_SEC_GRP_RAIL_OFF,
PCOM_CLK_REGIME_SEC_GRP_RAIL_ON,
PCOM_CLK_REGIME_SEC_VDC_RAIL_OFF,
PCOM_CLK_REGIME_SEC_VDC_RAIL_ON,
PCOM_CLK_REGIME_SEC_LCD_CTRL,
PCOM_CLK_REGIME_SEC_REGISTER_FOR_CPU_RESOURCE,
PCOM_CLK_REGIME_SEC_DEREGISTER_FOR_CPU_RESOURCE,
PCOM_CLK_REGIME_SEC_RESOURCE_REQUEST_WRP,
PCOM_CLK_REGIME_MSM_SEC_SEL_CLK_OWNER,
PCOM_CLK_REGIME_SEC_DEVMAN_REQUEST_WRP,
PCOM_GPIO_CONFIG,
PCOM_GPIO_CONFIGURE_GROUP,
PCOM_GPIO_TLMM_SET_PORT,
PCOM_GPIO_TLMM_CONFIG_EX,
PCOM_SET_FTM_BOOT_COUNT,
PCOM_RESERVED0,
PCOM_RESERVED1,
PCOM_CUSTOMER_CMD1,
PCOM_CUSTOMER_CMD2,
PCOM_CUSTOMER_CMD3,
PCOM_CLK_REGIME_ENTER_APPSBL_CHG_MODE,
PCOM_CLK_REGIME_EXIT_APPSBL_CHG_MODE,
PCOM_CLK_REGIME_SEC_RAIL_DISABLE,
PCOM_CLK_REGIME_SEC_RAIL_ENABLE,
PCOM_CLK_REGIME_SEC_RAIL_CONTROL,
PCOM_SET_SW_WATCHDOG_STATE,
PCOM_PM_MPP_CONFIG_DIGITAL_INPUT,
PCOM_PM_MPP_CONFIG_I_SINK,
PCOM_RESERVED_101,
PCOM_MSM_HSUSB_PHY_RESET,
PCOM_GET_BATT_MV_LEVEL,
PCOM_CHG_USB_IS_PC_CONNECTED,
PCOM_CHG_USB_IS_CHARGER_CONNECTED,
PCOM_CHG_USB_IS_DISCONNECTED,
PCOM_CHG_USB_IS_AVAILABLE,
PCOM_CLK_REGIME_SEC_MSM_SEL_FREQ,
PCOM_CLK_REGIME_SEC_SET_PCLK_AXI_POLICY,
PCOM_CLKCTL_RPC_RESET_ASSERT,
PCOM_CLKCTL_RPC_RESET_DEASSERT,
PCOM_CLKCTL_RPC_RAIL_ON,
PCOM_CLKCTL_RPC_RAIL_OFF,
PCOM_CLKCTL_RPC_RAIL_ENABLE,
PCOM_CLKCTL_RPC_RAIL_DISABLE,
PCOM_CLKCTL_RPC_RAIL_CONTROL,
PCOM_CLKCTL_RPC_MIN_MSMC1,
PCOM_NUM_CMDS,
};
enum {
PCOM_INVALID_STATUS = 0x0,
PCOM_READY,
PCOM_CMD_RUNNING,
PCOM_CMD_SUCCESS,
PCOM_CMD_FAIL,
PCOM_CMD_FAIL_FALSE_RETURNED,
PCOM_CMD_FAIL_CMD_OUT_OF_BOUNDS_SERVER,
PCOM_CMD_FAIL_CMD_OUT_OF_BOUNDS_CLIENT,
PCOM_CMD_FAIL_CMD_UNREGISTERED,
PCOM_CMD_FAIL_CMD_LOCKED,
PCOM_CMD_FAIL_SERVER_NOT_YET_READY,
PCOM_CMD_FAIL_BAD_DESTINATION,
PCOM_CMD_FAIL_SERVER_RESET,
PCOM_CMD_FAIL_SMSM_NOT_INIT,
PCOM_CMD_FAIL_PROC_COMM_BUSY,
PCOM_CMD_FAIL_PROC_COMM_NOT_INIT,
};
/* List of VREGs that support the Pull Down Resistor setting. */
enum vreg_pdown_id {
PM_VREG_PDOWN_MSMA_ID,
PM_VREG_PDOWN_MSMP_ID,
PM_VREG_PDOWN_MSME1_ID, /* Not supported in Panoramix */
PM_VREG_PDOWN_MSMC1_ID, /* Not supported in PM6620 */
PM_VREG_PDOWN_MSMC2_ID, /* Supported in PM7500 only */
PM_VREG_PDOWN_GP3_ID, /* Supported in PM7500 only */
PM_VREG_PDOWN_MSME2_ID, /* Supported in PM7500 and Panoramix only */
PM_VREG_PDOWN_GP4_ID, /* Supported in PM7500 only */
PM_VREG_PDOWN_GP1_ID, /* Supported in PM7500 only */
PM_VREG_PDOWN_TCXO_ID,
PM_VREG_PDOWN_PA_ID,
PM_VREG_PDOWN_RFTX_ID,
PM_VREG_PDOWN_RFRX1_ID,
PM_VREG_PDOWN_RFRX2_ID,
PM_VREG_PDOWN_SYNT_ID,
PM_VREG_PDOWN_WLAN_ID,
PM_VREG_PDOWN_USB_ID,
PM_VREG_PDOWN_MMC_ID,
PM_VREG_PDOWN_RUIM_ID,
PM_VREG_PDOWN_MSMC0_ID, /* Supported in PM6610 only */
PM_VREG_PDOWN_GP2_ID, /* Supported in PM7500 only */
PM_VREG_PDOWN_GP5_ID, /* Supported in PM7500 only */
PM_VREG_PDOWN_GP6_ID, /* Supported in PM7500 only */
PM_VREG_PDOWN_RF_ID,
PM_VREG_PDOWN_RF_VCO_ID,
PM_VREG_PDOWN_MPLL_ID,
PM_VREG_PDOWN_S2_ID,
PM_VREG_PDOWN_S3_ID,
PM_VREG_PDOWN_RFUBM_ID,
/* new for HAN */
PM_VREG_PDOWN_RF1_ID,
PM_VREG_PDOWN_RF2_ID,
PM_VREG_PDOWN_RFA_ID,
PM_VREG_PDOWN_CDC2_ID,
PM_VREG_PDOWN_RFTX2_ID,
PM_VREG_PDOWN_USIM_ID,
PM_VREG_PDOWN_USB2P6_ID,
PM_VREG_PDOWN_USB3P3_ID,
PM_VREG_PDOWN_INVALID_ID,
/* backward compatible enums only */
PM_VREG_PDOWN_CAM_ID = PM_VREG_PDOWN_GP1_ID,
PM_VREG_PDOWN_MDDI_ID = PM_VREG_PDOWN_GP2_ID,
PM_VREG_PDOWN_RUIM2_ID = PM_VREG_PDOWN_GP3_ID,
PM_VREG_PDOWN_AUX_ID = PM_VREG_PDOWN_GP4_ID,
PM_VREG_PDOWN_AUX2_ID = PM_VREG_PDOWN_GP5_ID,
PM_VREG_PDOWN_BT_ID = PM_VREG_PDOWN_GP6_ID,
PM_VREG_PDOWN_MSME_ID = PM_VREG_PDOWN_MSME1_ID,
PM_VREG_PDOWN_MSMC_ID = PM_VREG_PDOWN_MSMC1_ID,
PM_VREG_PDOWN_RFA1_ID = PM_VREG_PDOWN_RFRX2_ID,
PM_VREG_PDOWN_RFA2_ID = PM_VREG_PDOWN_RFTX2_ID,
PM_VREG_PDOWN_XO_ID = PM_VREG_PDOWN_TCXO_ID
};
enum {
PCOM_CLKRGM_APPS_RESET_USB_PHY = 34,
PCOM_CLKRGM_APPS_RESET_USBH = 37,
};
/* gpio info for PCOM_RPC_GPIO_TLMM_CONFIG_EX */
#define GPIO_ENABLE 0
#define GPIO_DISABLE 1
#define GPIO_INPUT 0
#define GPIO_OUTPUT 1
#define GPIO_NO_PULL 0
#define GPIO_PULL_DOWN 1
#define GPIO_KEEPER 2
#define GPIO_PULL_UP 3
#define GPIO_2MA 0
#define GPIO_4MA 1
#define GPIO_6MA 2
#define GPIO_8MA 3
#define GPIO_10MA 4
#define GPIO_12MA 5
#define GPIO_14MA 6
#define GPIO_16MA 7
#define PCOM_GPIO_CFG(gpio, func, dir, pull, drvstr) \
((((gpio) & 0x3FF) << 4) | \
((func) & 0xf) | \
(((dir) & 0x1) << 14) | \
(((pull) & 0x3) << 15) | \
(((drvstr) & 0xF) << 17))
int msm_proc_comm(unsigned cmd, unsigned *data1, unsigned *data2);
void proc_comm_boot_wait(void);
#endif