linux-sg2042/arch/arm/mach-mx5/board-mx51_efikamx.c

120 lines
3.2 KiB
C

/*
* Copyright (C) 2010 Linaro Limited
*
* based on code from the following
* Copyright 2009-2010 Freescale Semiconductor, Inc. All Rights Reserved.
* Copyright 2009-2010 Pegatron Corporation. All Rights Reserved.
* Copyright 2009-2010 Genesi USA, Inc. All Rights Reserved.
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
* Version 2 or later at the following locations:
*
* http://www.opensource.org/licenses/gpl-license.html
* http://www.gnu.org/copyleft/gpl.html
*/
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/i2c.h>
#include <linux/gpio.h>
#include <linux/delay.h>
#include <linux/io.h>
#include <linux/fsl_devices.h>
#include <mach/common.h>
#include <mach/hardware.h>
#include <mach/iomux-mx51.h>
#include <mach/i2c.h>
#include <mach/mxc_ehci.h>
#include <asm/irq.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
#include "devices-imx51.h"
#include "devices.h"
#define MX51_USB_PLL_DIV_24_MHZ 0x01
static struct pad_desc mx51efikamx_pads[] = {
/* UART1 */
MX51_PAD_UART1_RXD__UART1_RXD,
MX51_PAD_UART1_TXD__UART1_TXD,
MX51_PAD_UART1_RTS__UART1_RTS,
MX51_PAD_UART1_CTS__UART1_CTS,
};
/* Serial ports */
#if defined(CONFIG_SERIAL_IMX) || defined(CONFIG_SERIAL_IMX_MODULE)
static const struct imxuart_platform_data uart_pdata = {
.flags = IMXUART_HAVE_RTSCTS,
};
static inline void mxc_init_imx_uart(void)
{
imx51_add_imx_uart(0, &uart_pdata);
imx51_add_imx_uart(1, &uart_pdata);
imx51_add_imx_uart(2, &uart_pdata);
}
#else /* !SERIAL_IMX */
static inline void mxc_init_imx_uart(void)
{
}
#endif /* SERIAL_IMX */
/* This function is board specific as the bit mask for the plldiv will also
* be different for other Freescale SoCs, thus a common bitmask is not
* possible and cannot get place in /plat-mxc/ehci.c.
*/
static int initialize_otg_port(struct platform_device *pdev)
{
u32 v;
void __iomem *usb_base;
void __iomem *usbother_base;
usb_base = ioremap(MX51_OTG_BASE_ADDR, SZ_4K);
usbother_base = (void __iomem *)(usb_base + MX5_USBOTHER_REGS_OFFSET);
/* Set the PHY clock to 19.2MHz */
v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
v &= ~MX5_USB_UTMI_PHYCTRL1_PLLDIV_MASK;
v |= MX51_USB_PLL_DIV_24_MHZ;
__raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
iounmap(usb_base);
return 0;
}
static struct mxc_usbh_platform_data dr_utmi_config = {
.init = initialize_otg_port,
.portsc = MXC_EHCI_UTMI_16BIT,
.flags = MXC_EHCI_INTERNAL_PHY,
};
static void __init mxc_board_init(void)
{
mxc_iomux_v3_setup_multiple_pads(mx51efikamx_pads,
ARRAY_SIZE(mx51efikamx_pads));
mxc_register_device(&mxc_usbdr_host_device, &dr_utmi_config);
mxc_init_imx_uart();
}
static void __init mx51_efikamx_timer_init(void)
{
mx51_clocks_init(32768, 24000000, 22579200, 24576000);
}
static struct sys_timer mxc_timer = {
.init = mx51_efikamx_timer_init,
};
MACHINE_START(MX51_EFIKAMX, "Genesi EfikaMX nettop")
/* Maintainer: Amit Kucheria <amit.kucheria@linaro.org> */
.boot_params = MX51_PHYS_OFFSET + 0x100,
.map_io = mx51_map_io,
.init_irq = mx51_init_irq,
.init_machine = mxc_board_init,
.timer = &mxc_timer,
MACHINE_END