435 lines
11 KiB
C
435 lines
11 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
|
/* Driver for the Texas Instruments DP83869 PHY
|
|
* Copyright (C) 2019 Texas Instruments Inc.
|
|
*/
|
|
|
|
#include <linux/ethtool.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/mii.h>
|
|
#include <linux/module.h>
|
|
#include <linux/of.h>
|
|
#include <linux/phy.h>
|
|
#include <linux/delay.h>
|
|
|
|
#include <dt-bindings/net/ti-dp83869.h>
|
|
|
|
#define DP83869_PHY_ID 0x2000a0f1
|
|
#define DP83869_DEVADDR 0x1f
|
|
|
|
#define MII_DP83869_PHYCTRL 0x10
|
|
#define MII_DP83869_MICR 0x12
|
|
#define MII_DP83869_ISR 0x13
|
|
#define DP83869_CTRL 0x1f
|
|
#define DP83869_CFG4 0x1e
|
|
|
|
/* Extended Registers */
|
|
#define DP83869_GEN_CFG3 0x0031
|
|
#define DP83869_RGMIICTL 0x0032
|
|
#define DP83869_STRAP_STS1 0x006e
|
|
#define DP83869_RGMIIDCTL 0x0086
|
|
#define DP83869_IO_MUX_CFG 0x0170
|
|
#define DP83869_OP_MODE 0x01df
|
|
#define DP83869_FX_CTRL 0x0c00
|
|
|
|
#define DP83869_SW_RESET BIT(15)
|
|
#define DP83869_SW_RESTART BIT(14)
|
|
|
|
/* MICR Interrupt bits */
|
|
#define MII_DP83869_MICR_AN_ERR_INT_EN BIT(15)
|
|
#define MII_DP83869_MICR_SPEED_CHNG_INT_EN BIT(14)
|
|
#define MII_DP83869_MICR_DUP_MODE_CHNG_INT_EN BIT(13)
|
|
#define MII_DP83869_MICR_PAGE_RXD_INT_EN BIT(12)
|
|
#define MII_DP83869_MICR_AUTONEG_COMP_INT_EN BIT(11)
|
|
#define MII_DP83869_MICR_LINK_STS_CHNG_INT_EN BIT(10)
|
|
#define MII_DP83869_MICR_FALSE_CARRIER_INT_EN BIT(8)
|
|
#define MII_DP83869_MICR_SLEEP_MODE_CHNG_INT_EN BIT(4)
|
|
#define MII_DP83869_MICR_WOL_INT_EN BIT(3)
|
|
#define MII_DP83869_MICR_XGMII_ERR_INT_EN BIT(2)
|
|
#define MII_DP83869_MICR_POL_CHNG_INT_EN BIT(1)
|
|
#define MII_DP83869_MICR_JABBER_INT_EN BIT(0)
|
|
|
|
#define MII_DP83869_BMCR_DEFAULT (BMCR_ANENABLE | \
|
|
BMCR_FULLDPLX | \
|
|
BMCR_SPEED1000)
|
|
|
|
/* This is the same bit mask as the BMCR so re-use the BMCR default */
|
|
#define DP83869_FX_CTRL_DEFAULT MII_DP83869_BMCR_DEFAULT
|
|
|
|
/* CFG1 bits */
|
|
#define DP83869_CFG1_DEFAULT (ADVERTISE_1000HALF | \
|
|
ADVERTISE_1000FULL | \
|
|
CTL1000_AS_MASTER)
|
|
|
|
/* RGMIICTL bits */
|
|
#define DP83869_RGMII_TX_CLK_DELAY_EN BIT(1)
|
|
#define DP83869_RGMII_RX_CLK_DELAY_EN BIT(0)
|
|
|
|
/* STRAP_STS1 bits */
|
|
#define DP83869_STRAP_STS1_RESERVED BIT(11)
|
|
|
|
/* PHYCTRL bits */
|
|
#define DP83869_RX_FIFO_SHIFT 12
|
|
#define DP83869_TX_FIFO_SHIFT 14
|
|
|
|
/* PHY_CTRL lower bytes 0x48 are declared as reserved */
|
|
#define DP83869_PHY_CTRL_DEFAULT 0x48
|
|
#define DP83869_PHYCR_FIFO_DEPTH_MASK GENMASK(15, 12)
|
|
#define DP83869_PHYCR_RESERVED_MASK BIT(11)
|
|
|
|
/* RGMIIDCTL bits */
|
|
#define DP83869_RGMII_TX_CLK_DELAY_SHIFT 4
|
|
|
|
/* IO_MUX_CFG bits */
|
|
#define DP83869_IO_MUX_CFG_IO_IMPEDANCE_CTRL 0x1f
|
|
|
|
#define DP83869_IO_MUX_CFG_IO_IMPEDANCE_MAX 0x0
|
|
#define DP83869_IO_MUX_CFG_IO_IMPEDANCE_MIN 0x1f
|
|
#define DP83869_IO_MUX_CFG_CLK_O_SEL_MASK (0x1f << 8)
|
|
#define DP83869_IO_MUX_CFG_CLK_O_SEL_SHIFT 8
|
|
|
|
/* CFG3 bits */
|
|
#define DP83869_CFG3_PORT_MIRROR_EN BIT(0)
|
|
|
|
/* CFG4 bits */
|
|
#define DP83869_INT_OE BIT(7)
|
|
|
|
/* OP MODE */
|
|
#define DP83869_OP_MODE_MII BIT(5)
|
|
#define DP83869_SGMII_RGMII_BRIDGE BIT(6)
|
|
|
|
enum {
|
|
DP83869_PORT_MIRRORING_KEEP,
|
|
DP83869_PORT_MIRRORING_EN,
|
|
DP83869_PORT_MIRRORING_DIS,
|
|
};
|
|
|
|
struct dp83869_private {
|
|
int tx_fifo_depth;
|
|
int rx_fifo_depth;
|
|
int io_impedance;
|
|
int port_mirroring;
|
|
bool rxctrl_strap_quirk;
|
|
int clk_output_sel;
|
|
int mode;
|
|
};
|
|
|
|
static int dp83869_ack_interrupt(struct phy_device *phydev)
|
|
{
|
|
int err = phy_read(phydev, MII_DP83869_ISR);
|
|
|
|
if (err < 0)
|
|
return err;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int dp83869_config_intr(struct phy_device *phydev)
|
|
{
|
|
int micr_status = 0;
|
|
|
|
if (phydev->interrupts == PHY_INTERRUPT_ENABLED) {
|
|
micr_status = phy_read(phydev, MII_DP83869_MICR);
|
|
if (micr_status < 0)
|
|
return micr_status;
|
|
|
|
micr_status |=
|
|
(MII_DP83869_MICR_AN_ERR_INT_EN |
|
|
MII_DP83869_MICR_SPEED_CHNG_INT_EN |
|
|
MII_DP83869_MICR_AUTONEG_COMP_INT_EN |
|
|
MII_DP83869_MICR_LINK_STS_CHNG_INT_EN |
|
|
MII_DP83869_MICR_DUP_MODE_CHNG_INT_EN |
|
|
MII_DP83869_MICR_SLEEP_MODE_CHNG_INT_EN);
|
|
|
|
return phy_write(phydev, MII_DP83869_MICR, micr_status);
|
|
}
|
|
|
|
return phy_write(phydev, MII_DP83869_MICR, micr_status);
|
|
}
|
|
|
|
static int dp83869_config_port_mirroring(struct phy_device *phydev)
|
|
{
|
|
struct dp83869_private *dp83869 = phydev->priv;
|
|
|
|
if (dp83869->port_mirroring == DP83869_PORT_MIRRORING_EN)
|
|
return phy_set_bits_mmd(phydev, DP83869_DEVADDR,
|
|
DP83869_GEN_CFG3,
|
|
DP83869_CFG3_PORT_MIRROR_EN);
|
|
else
|
|
return phy_clear_bits_mmd(phydev, DP83869_DEVADDR,
|
|
DP83869_GEN_CFG3,
|
|
DP83869_CFG3_PORT_MIRROR_EN);
|
|
}
|
|
|
|
#ifdef CONFIG_OF_MDIO
|
|
static int dp83869_of_init(struct phy_device *phydev)
|
|
{
|
|
struct dp83869_private *dp83869 = phydev->priv;
|
|
struct device *dev = &phydev->mdio.dev;
|
|
struct device_node *of_node = dev->of_node;
|
|
int ret;
|
|
|
|
if (!of_node)
|
|
return -ENODEV;
|
|
|
|
dp83869->io_impedance = -EINVAL;
|
|
|
|
/* Optional configuration */
|
|
ret = of_property_read_u32(of_node, "ti,clk-output-sel",
|
|
&dp83869->clk_output_sel);
|
|
if (ret || dp83869->clk_output_sel > DP83869_CLK_O_SEL_REF_CLK)
|
|
dp83869->clk_output_sel = DP83869_CLK_O_SEL_REF_CLK;
|
|
|
|
ret = of_property_read_u32(of_node, "ti,op-mode", &dp83869->mode);
|
|
if (ret == 0) {
|
|
if (dp83869->mode < DP83869_RGMII_COPPER_ETHERNET ||
|
|
dp83869->mode > DP83869_SGMII_COPPER_ETHERNET)
|
|
return -EINVAL;
|
|
}
|
|
|
|
if (of_property_read_bool(of_node, "ti,max-output-impedance"))
|
|
dp83869->io_impedance = DP83869_IO_MUX_CFG_IO_IMPEDANCE_MAX;
|
|
else if (of_property_read_bool(of_node, "ti,min-output-impedance"))
|
|
dp83869->io_impedance = DP83869_IO_MUX_CFG_IO_IMPEDANCE_MIN;
|
|
|
|
if (of_property_read_bool(of_node, "enet-phy-lane-swap"))
|
|
dp83869->port_mirroring = DP83869_PORT_MIRRORING_EN;
|
|
else
|
|
dp83869->port_mirroring = DP83869_PORT_MIRRORING_DIS;
|
|
|
|
if (of_property_read_u32(of_node, "rx-fifo-depth",
|
|
&dp83869->rx_fifo_depth))
|
|
dp83869->rx_fifo_depth = DP83869_PHYCR_FIFO_DEPTH_4_B_NIB;
|
|
|
|
if (of_property_read_u32(of_node, "tx-fifo-depth",
|
|
&dp83869->tx_fifo_depth))
|
|
dp83869->tx_fifo_depth = DP83869_PHYCR_FIFO_DEPTH_4_B_NIB;
|
|
|
|
return ret;
|
|
}
|
|
#else
|
|
static int dp83869_of_init(struct phy_device *phydev)
|
|
{
|
|
return 0;
|
|
}
|
|
#endif /* CONFIG_OF_MDIO */
|
|
|
|
static int dp83869_configure_rgmii(struct phy_device *phydev,
|
|
struct dp83869_private *dp83869)
|
|
{
|
|
int ret = 0, val;
|
|
|
|
if (phy_interface_is_rgmii(phydev)) {
|
|
val = phy_read(phydev, MII_DP83869_PHYCTRL);
|
|
if (val < 0)
|
|
return val;
|
|
|
|
val &= ~DP83869_PHYCR_FIFO_DEPTH_MASK;
|
|
val |= (dp83869->tx_fifo_depth << DP83869_TX_FIFO_SHIFT);
|
|
val |= (dp83869->rx_fifo_depth << DP83869_RX_FIFO_SHIFT);
|
|
|
|
ret = phy_write(phydev, MII_DP83869_PHYCTRL, val);
|
|
if (ret)
|
|
return ret;
|
|
}
|
|
|
|
if (dp83869->io_impedance >= 0)
|
|
ret = phy_modify_mmd(phydev, DP83869_DEVADDR,
|
|
DP83869_IO_MUX_CFG,
|
|
DP83869_IO_MUX_CFG_IO_IMPEDANCE_CTRL,
|
|
dp83869->io_impedance &
|
|
DP83869_IO_MUX_CFG_IO_IMPEDANCE_CTRL);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int dp83869_configure_mode(struct phy_device *phydev,
|
|
struct dp83869_private *dp83869)
|
|
{
|
|
int phy_ctrl_val;
|
|
int ret;
|
|
|
|
if (dp83869->mode < DP83869_RGMII_COPPER_ETHERNET ||
|
|
dp83869->mode > DP83869_SGMII_COPPER_ETHERNET)
|
|
return -EINVAL;
|
|
|
|
/* Below init sequence for each operational mode is defined in
|
|
* section 9.4.8 of the datasheet.
|
|
*/
|
|
ret = phy_write_mmd(phydev, DP83869_DEVADDR, DP83869_OP_MODE,
|
|
dp83869->mode);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = phy_write(phydev, MII_BMCR, MII_DP83869_BMCR_DEFAULT);
|
|
if (ret)
|
|
return ret;
|
|
|
|
phy_ctrl_val = (dp83869->rx_fifo_depth << DP83869_RX_FIFO_SHIFT |
|
|
dp83869->tx_fifo_depth << DP83869_TX_FIFO_SHIFT |
|
|
DP83869_PHY_CTRL_DEFAULT);
|
|
|
|
switch (dp83869->mode) {
|
|
case DP83869_RGMII_COPPER_ETHERNET:
|
|
ret = phy_write(phydev, MII_DP83869_PHYCTRL,
|
|
phy_ctrl_val);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = phy_write(phydev, MII_CTRL1000, DP83869_CFG1_DEFAULT);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = dp83869_configure_rgmii(phydev, dp83869);
|
|
if (ret)
|
|
return ret;
|
|
break;
|
|
case DP83869_RGMII_SGMII_BRIDGE:
|
|
ret = phy_modify_mmd(phydev, DP83869_DEVADDR, DP83869_OP_MODE,
|
|
DP83869_SGMII_RGMII_BRIDGE,
|
|
DP83869_SGMII_RGMII_BRIDGE);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = phy_write_mmd(phydev, DP83869_DEVADDR,
|
|
DP83869_FX_CTRL, DP83869_FX_CTRL_DEFAULT);
|
|
if (ret)
|
|
return ret;
|
|
|
|
break;
|
|
case DP83869_1000M_MEDIA_CONVERT:
|
|
ret = phy_write(phydev, MII_DP83869_PHYCTRL,
|
|
phy_ctrl_val);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = phy_write_mmd(phydev, DP83869_DEVADDR,
|
|
DP83869_FX_CTRL, DP83869_FX_CTRL_DEFAULT);
|
|
if (ret)
|
|
return ret;
|
|
break;
|
|
case DP83869_100M_MEDIA_CONVERT:
|
|
ret = phy_write(phydev, MII_DP83869_PHYCTRL,
|
|
phy_ctrl_val);
|
|
if (ret)
|
|
return ret;
|
|
break;
|
|
case DP83869_SGMII_COPPER_ETHERNET:
|
|
ret = phy_write(phydev, MII_DP83869_PHYCTRL,
|
|
phy_ctrl_val);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = phy_write(phydev, MII_CTRL1000, DP83869_CFG1_DEFAULT);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = phy_write_mmd(phydev, DP83869_DEVADDR,
|
|
DP83869_FX_CTRL, DP83869_FX_CTRL_DEFAULT);
|
|
if (ret)
|
|
return ret;
|
|
|
|
break;
|
|
case DP83869_RGMII_1000_BASE:
|
|
case DP83869_RGMII_100_BASE:
|
|
break;
|
|
default:
|
|
return -EINVAL;
|
|
};
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int dp83869_config_init(struct phy_device *phydev)
|
|
{
|
|
struct dp83869_private *dp83869 = phydev->priv;
|
|
int ret, val;
|
|
|
|
ret = dp83869_configure_mode(phydev, dp83869);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* Enable Interrupt output INT_OE in CFG4 register */
|
|
if (phy_interrupt_is_valid(phydev)) {
|
|
val = phy_read(phydev, DP83869_CFG4);
|
|
val |= DP83869_INT_OE;
|
|
phy_write(phydev, DP83869_CFG4, val);
|
|
}
|
|
|
|
if (dp83869->port_mirroring != DP83869_PORT_MIRRORING_KEEP)
|
|
dp83869_config_port_mirroring(phydev);
|
|
|
|
/* Clock output selection if muxing property is set */
|
|
if (dp83869->clk_output_sel != DP83869_CLK_O_SEL_REF_CLK)
|
|
ret = phy_modify_mmd(phydev,
|
|
DP83869_DEVADDR, DP83869_IO_MUX_CFG,
|
|
DP83869_IO_MUX_CFG_CLK_O_SEL_MASK,
|
|
dp83869->clk_output_sel <<
|
|
DP83869_IO_MUX_CFG_CLK_O_SEL_SHIFT);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int dp83869_probe(struct phy_device *phydev)
|
|
{
|
|
struct dp83869_private *dp83869;
|
|
int ret;
|
|
|
|
dp83869 = devm_kzalloc(&phydev->mdio.dev, sizeof(*dp83869),
|
|
GFP_KERNEL);
|
|
if (!dp83869)
|
|
return -ENOMEM;
|
|
|
|
phydev->priv = dp83869;
|
|
|
|
ret = dp83869_of_init(phydev);
|
|
if (ret)
|
|
return ret;
|
|
|
|
return dp83869_config_init(phydev);
|
|
}
|
|
|
|
static int dp83869_phy_reset(struct phy_device *phydev)
|
|
{
|
|
int ret;
|
|
|
|
ret = phy_write(phydev, DP83869_CTRL, DP83869_SW_RESET);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
usleep_range(10, 20);
|
|
|
|
/* Global sw reset sets all registers to default.
|
|
* Need to set the registers in the PHY to the right config.
|
|
*/
|
|
return dp83869_config_init(phydev);
|
|
}
|
|
|
|
static struct phy_driver dp83869_driver[] = {
|
|
{
|
|
PHY_ID_MATCH_MODEL(DP83869_PHY_ID),
|
|
.name = "TI DP83869",
|
|
|
|
.probe = dp83869_probe,
|
|
.config_init = dp83869_config_init,
|
|
.soft_reset = dp83869_phy_reset,
|
|
|
|
/* IRQ related */
|
|
.ack_interrupt = dp83869_ack_interrupt,
|
|
.config_intr = dp83869_config_intr,
|
|
|
|
.suspend = genphy_suspend,
|
|
.resume = genphy_resume,
|
|
},
|
|
};
|
|
module_phy_driver(dp83869_driver);
|
|
|
|
static struct mdio_device_id __maybe_unused dp83869_tbl[] = {
|
|
{ PHY_ID_MATCH_MODEL(DP83869_PHY_ID) },
|
|
{ }
|
|
};
|
|
MODULE_DEVICE_TABLE(mdio, dp83869_tbl);
|
|
|
|
MODULE_DESCRIPTION("Texas Instruments DP83869 PHY driver");
|
|
MODULE_AUTHOR("Dan Murphy <dmurphy@ti.com");
|
|
MODULE_LICENSE("GPL v2");
|