51 lines
2.1 KiB
Plaintext
51 lines
2.1 KiB
Plaintext
* AT91 SAMA5D2 Analog to Digital Converter (ADC)
|
|
|
|
Required properties:
|
|
- compatible: Should be "atmel,sama5d2-adc" or "microchip,sam9x60-adc".
|
|
- reg: Should contain ADC registers location and length.
|
|
- interrupts: Should contain the IRQ line for the ADC.
|
|
- clocks: phandle to device clock.
|
|
- clock-names: Must be "adc_clk".
|
|
- vref-supply: Supply used as reference for conversions.
|
|
- vddana-supply: Supply for the adc device.
|
|
- atmel,min-sample-rate-hz: Minimum sampling rate, it depends on SoC.
|
|
- atmel,max-sample-rate-hz: Maximum sampling rate, it depends on SoC.
|
|
- atmel,startup-time-ms: Startup time expressed in ms, it depends on SoC.
|
|
- atmel,trigger-edge-type: One of possible edge types for the ADTRG hardware
|
|
trigger pin. When the specific edge type is detected, the conversion will
|
|
start. Possible values are rising, falling, or both.
|
|
This property uses the IRQ edge types values: IRQ_TYPE_EDGE_RISING ,
|
|
IRQ_TYPE_EDGE_FALLING or IRQ_TYPE_EDGE_BOTH
|
|
|
|
Optional properties:
|
|
- dmas: Phandle to dma channel for the ADC.
|
|
- dma-names: Must be "rx" when dmas property is being used.
|
|
See ../../dma/dma.txt for details.
|
|
- #io-channel-cells: in case consumer drivers are attached, this must be 1.
|
|
See <Documentation/devicetree/bindings/iio/iio-bindings.txt> for details.
|
|
|
|
Properties for consumer drivers:
|
|
- Consumer drivers can be connected to this producer device, as specified
|
|
in <Documentation/devicetree/bindings/iio/iio-bindings.txt>
|
|
- Channels exposed are specified in:
|
|
<dt-bindings/iio/adc/at91-sama5d2_adc.txt>
|
|
|
|
Example:
|
|
|
|
adc: adc@fc030000 {
|
|
compatible = "atmel,sama5d2-adc";
|
|
reg = <0xfc030000 0x100>;
|
|
interrupts = <40 IRQ_TYPE_LEVEL_HIGH 7>;
|
|
clocks = <&adc_clk>;
|
|
clock-names = "adc_clk";
|
|
atmel,min-sample-rate-hz = <200000>;
|
|
atmel,max-sample-rate-hz = <20000000>;
|
|
atmel,startup-time-ms = <4>;
|
|
vddana-supply = <&vdd_3v3_lp_reg>;
|
|
vref-supply = <&vdd_3v3_lp_reg>;
|
|
atmel,trigger-edge-type = <IRQ_TYPE_EDGE_BOTH>;
|
|
dmas = <&dma0 (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(25))>;
|
|
dma-names = "rx";
|
|
#io-channel-cells = <1>;
|
|
}
|