linux-sg2042/include/asm-powerpc/hvcall.h

299 lines
9.5 KiB
C

#ifndef _ASM_POWERPC_HVCALL_H
#define _ASM_POWERPC_HVCALL_H
#ifdef __KERNEL__
#define HVSC .long 0x44000022
#define H_SUCCESS 0
#define H_BUSY 1 /* Hardware busy -- retry later */
#define H_CLOSED 2 /* Resource closed */
#define H_NOT_AVAILABLE 3
#define H_CONSTRAINED 4 /* Resource request constrained to max allowed */
#define H_PARTIAL 5
#define H_IN_PROGRESS 14 /* Kind of like busy */
#define H_PAGE_REGISTERED 15
#define H_PARTIAL_STORE 16
#define H_PENDING 17 /* returned from H_POLL_PENDING */
#define H_CONTINUE 18 /* Returned from H_Join on success */
#define H_LONG_BUSY_START_RANGE 9900 /* Start of long busy range */
#define H_LONG_BUSY_ORDER_1_MSEC 9900 /* Long busy, hint that 1msec \
is a good time to retry */
#define H_LONG_BUSY_ORDER_10_MSEC 9901 /* Long busy, hint that 10msec \
is a good time to retry */
#define H_LONG_BUSY_ORDER_100_MSEC 9902 /* Long busy, hint that 100msec \
is a good time to retry */
#define H_LONG_BUSY_ORDER_1_SEC 9903 /* Long busy, hint that 1sec \
is a good time to retry */
#define H_LONG_BUSY_ORDER_10_SEC 9904 /* Long busy, hint that 10sec \
is a good time to retry */
#define H_LONG_BUSY_ORDER_100_SEC 9905 /* Long busy, hint that 100sec \
is a good time to retry */
#define H_LONG_BUSY_END_RANGE 9905 /* End of long busy range */
#define H_HARDWARE -1 /* Hardware error */
#define H_FUNCTION -2 /* Function not supported */
#define H_PRIVILEGE -3 /* Caller not privileged */
#define H_PARAMETER -4 /* Parameter invalid, out-of-range or conflicting */
#define H_BAD_MODE -5 /* Illegal msr value */
#define H_PTEG_FULL -6 /* PTEG is full */
#define H_NOT_FOUND -7 /* PTE was not found" */
#define H_RESERVED_DABR -8 /* DABR address is reserved by the hypervisor on this processor" */
#define H_NO_MEM -9
#define H_AUTHORITY -10
#define H_PERMISSION -11
#define H_DROPPED -12
#define H_SOURCE_PARM -13
#define H_DEST_PARM -14
#define H_REMOTE_PARM -15
#define H_RESOURCE -16
#define H_ADAPTER_PARM -17
#define H_RH_PARM -18
#define H_RCQ_PARM -19
#define H_SCQ_PARM -20
#define H_EQ_PARM -21
#define H_RT_PARM -22
#define H_ST_PARM -23
#define H_SIGT_PARM -24
#define H_TOKEN_PARM -25
#define H_MLENGTH_PARM -27
#define H_MEM_PARM -28
#define H_MEM_ACCESS_PARM -29
#define H_ATTR_PARM -30
#define H_PORT_PARM -31
#define H_MCG_PARM -32
#define H_VL_PARM -33
#define H_TSIZE_PARM -34
#define H_TRACE_PARM -35
#define H_MASK_PARM -37
#define H_MCG_FULL -38
#define H_ALIAS_EXIST -39
#define H_P_COUNTER -40
#define H_TABLE_FULL -41
#define H_ALT_TABLE -42
#define H_MR_CONDITION -43
#define H_NOT_ENOUGH_RESOURCES -44
#define H_R_STATE -45
#define H_RESCINDEND -46
/* Long Busy is a condition that can be returned by the firmware
* when a call cannot be completed now, but the identical call
* should be retried later. This prevents calls blocking in the
* firmware for long periods of time. Annoyingly the firmware can return
* a range of return codes, hinting at how long we should wait before
* retrying. If you don't care for the hint, the macro below is a good
* way to check for the long_busy return codes
*/
#define H_IS_LONG_BUSY(x) ((x >= H_LONG_BUSY_START_RANGE) \
&& (x <= H_LONG_BUSY_END_RANGE))
/* Flags */
#define H_LARGE_PAGE (1UL<<(63-16))
#define H_EXACT (1UL<<(63-24)) /* Use exact PTE or return H_PTEG_FULL */
#define H_R_XLATE (1UL<<(63-25)) /* include a valid logical page num in the pte if the valid bit is set */
#define H_READ_4 (1UL<<(63-26)) /* Return 4 PTEs */
#define H_AVPN (1UL<<(63-32)) /* An avpn is provided as a sanity test */
#define H_ANDCOND (1UL<<(63-33))
#define H_ICACHE_INVALIDATE (1UL<<(63-40)) /* icbi, etc. (ignored for IO pages) */
#define H_ICACHE_SYNCHRONIZE (1UL<<(63-41)) /* dcbst, icbi, etc (ignored for IO pages */
#define H_ZERO_PAGE (1UL<<(63-48)) /* zero the page before mapping (ignored for IO pages) */
#define H_COPY_PAGE (1UL<<(63-49))
#define H_N (1UL<<(63-61))
#define H_PP1 (1UL<<(63-62))
#define H_PP2 (1UL<<(63-63))
/* VASI States */
#define H_VASI_INVALID 0
#define H_VASI_ENABLED 1
#define H_VASI_ABORTED 2
#define H_VASI_SUSPENDING 3
#define H_VASI_SUSPENDED 4
#define H_VASI_RESUMED 5
#define H_VASI_COMPLETED 6
/* DABRX flags */
#define H_DABRX_HYPERVISOR (1UL<<(63-61))
#define H_DABRX_KERNEL (1UL<<(63-62))
#define H_DABRX_USER (1UL<<(63-63))
/* Each control block has to be on a 4K bondary */
#define H_CB_ALIGNMENT 4096
/* pSeries hypervisor opcodes */
#define H_REMOVE 0x04
#define H_ENTER 0x08
#define H_READ 0x0c
#define H_CLEAR_MOD 0x10
#define H_CLEAR_REF 0x14
#define H_PROTECT 0x18
#define H_GET_TCE 0x1c
#define H_PUT_TCE 0x20
#define H_SET_SPRG0 0x24
#define H_SET_DABR 0x28
#define H_PAGE_INIT 0x2c
#define H_SET_ASR 0x30
#define H_ASR_ON 0x34
#define H_ASR_OFF 0x38
#define H_LOGICAL_CI_LOAD 0x3c
#define H_LOGICAL_CI_STORE 0x40
#define H_LOGICAL_CACHE_LOAD 0x44
#define H_LOGICAL_CACHE_STORE 0x48
#define H_LOGICAL_ICBI 0x4c
#define H_LOGICAL_DCBF 0x50
#define H_GET_TERM_CHAR 0x54
#define H_PUT_TERM_CHAR 0x58
#define H_REAL_TO_LOGICAL 0x5c
#define H_HYPERVISOR_DATA 0x60
#define H_EOI 0x64
#define H_CPPR 0x68
#define H_IPI 0x6c
#define H_IPOLL 0x70
#define H_XIRR 0x74
#define H_PERFMON 0x7c
#define H_MIGRATE_DMA 0x78
#define H_REGISTER_VPA 0xDC
#define H_CEDE 0xE0
#define H_CONFER 0xE4
#define H_PROD 0xE8
#define H_GET_PPP 0xEC
#define H_SET_PPP 0xF0
#define H_PURR 0xF4
#define H_PIC 0xF8
#define H_REG_CRQ 0xFC
#define H_FREE_CRQ 0x100
#define H_VIO_SIGNAL 0x104
#define H_SEND_CRQ 0x108
#define H_COPY_RDMA 0x110
#define H_SET_XDABR 0x134
#define H_STUFF_TCE 0x138
#define H_PUT_TCE_INDIRECT 0x13C
#define H_VTERM_PARTNER_INFO 0x150
#define H_REGISTER_VTERM 0x154
#define H_FREE_VTERM 0x158
#define H_RESET_EVENTS 0x15C
#define H_ALLOC_RESOURCE 0x160
#define H_FREE_RESOURCE 0x164
#define H_MODIFY_QP 0x168
#define H_QUERY_QP 0x16C
#define H_REREGISTER_PMR 0x170
#define H_REGISTER_SMR 0x174
#define H_QUERY_MR 0x178
#define H_QUERY_MW 0x17C
#define H_QUERY_HCA 0x180
#define H_QUERY_PORT 0x184
#define H_MODIFY_PORT 0x188
#define H_DEFINE_AQP1 0x18C
#define H_GET_TRACE_BUFFER 0x190
#define H_DEFINE_AQP0 0x194
#define H_RESIZE_MR 0x198
#define H_ATTACH_MCQP 0x19C
#define H_DETACH_MCQP 0x1A0
#define H_CREATE_RPT 0x1A4
#define H_REMOVE_RPT 0x1A8
#define H_REGISTER_RPAGES 0x1AC
#define H_DISABLE_AND_GETC 0x1B0
#define H_ERROR_DATA 0x1B4
#define H_GET_HCA_INFO 0x1B8
#define H_GET_PERF_COUNT 0x1BC
#define H_MANAGE_TRACE 0x1C0
#define H_QUERY_INT_STATE 0x1E4
#define H_POLL_PENDING 0x1D8
#define H_JOIN 0x298
#define H_VASI_STATE 0x2A4
#define H_ENABLE_CRQ 0x2B0
#ifndef __ASSEMBLY__
/* plpar_hcall() -- Generic call interface using above opcodes
*
* The actual call interface is a hypervisor call instruction with
* the opcode in R3 and input args in R4-R7.
* Status is returned in R3 with variable output values in R4-R11.
* Only H_PTE_READ with H_READ_4 uses R6-R11 so we ignore it for now
* and return only two out args which MUST ALWAYS BE PROVIDED.
*/
long plpar_hcall(unsigned long opcode,
unsigned long arg1,
unsigned long arg2,
unsigned long arg3,
unsigned long arg4,
unsigned long *out1,
unsigned long *out2,
unsigned long *out3);
/* Same as plpar_hcall but for those opcodes that return no values
* other than status. Slightly more efficient.
*/
long plpar_hcall_norets(unsigned long opcode, ...);
/*
* Special hcall interface for ibmveth support.
* Takes 8 input parms. Returns a rc and stores the
* R4 return value in *out1.
*/
long plpar_hcall_8arg_2ret(unsigned long opcode,
unsigned long arg1,
unsigned long arg2,
unsigned long arg3,
unsigned long arg4,
unsigned long arg5,
unsigned long arg6,
unsigned long arg7,
unsigned long arg8,
unsigned long *out1);
/* plpar_hcall_4out()
*
* same as plpar_hcall except with 4 output arguments.
*
*/
long plpar_hcall_4out(unsigned long opcode,
unsigned long arg1,
unsigned long arg2,
unsigned long arg3,
unsigned long arg4,
unsigned long *out1,
unsigned long *out2,
unsigned long *out3,
unsigned long *out4);
long plpar_hcall_7arg_7ret(unsigned long opcode,
unsigned long arg1,
unsigned long arg2,
unsigned long arg3,
unsigned long arg4,
unsigned long arg5,
unsigned long arg6,
unsigned long arg7,
unsigned long *out1,
unsigned long *out2,
unsigned long *out3,
unsigned long *out4,
unsigned long *out5,
unsigned long *out6,
unsigned long *out7);
long plpar_hcall_9arg_9ret(unsigned long opcode,
unsigned long arg1,
unsigned long arg2,
unsigned long arg3,
unsigned long arg4,
unsigned long arg5,
unsigned long arg6,
unsigned long arg7,
unsigned long arg8,
unsigned long arg9,
unsigned long *out1,
unsigned long *out2,
unsigned long *out3,
unsigned long *out4,
unsigned long *out5,
unsigned long *out6,
unsigned long *out7,
unsigned long *out8,
unsigned long *out9);
#endif /* __ASSEMBLY__ */
#endif /* __KERNEL__ */
#endif /* _ASM_POWERPC_HVCALL_H */