267 lines
8.6 KiB
C
267 lines
8.6 KiB
C
/* SPDX-License-Identifier: GPL-2.0-only */
|
|
/*
|
|
* machine.h -- SoC Regulator support, machine/board driver API.
|
|
*
|
|
* Copyright (C) 2007, 2008 Wolfson Microelectronics PLC.
|
|
*
|
|
* Author: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
*
|
|
* Regulator Machine/Board Interface.
|
|
*/
|
|
|
|
#ifndef __LINUX_REGULATOR_MACHINE_H_
|
|
#define __LINUX_REGULATOR_MACHINE_H_
|
|
|
|
#include <linux/regulator/consumer.h>
|
|
#include <linux/suspend.h>
|
|
|
|
struct regulator;
|
|
|
|
/*
|
|
* Regulator operation constraint flags. These flags are used to enable
|
|
* certain regulator operations and can be OR'ed together.
|
|
*
|
|
* VOLTAGE: Regulator output voltage can be changed by software on this
|
|
* board/machine.
|
|
* CURRENT: Regulator output current can be changed by software on this
|
|
* board/machine.
|
|
* MODE: Regulator operating mode can be changed by software on this
|
|
* board/machine.
|
|
* STATUS: Regulator can be enabled and disabled.
|
|
* DRMS: Dynamic Regulator Mode Switching is enabled for this regulator.
|
|
* BYPASS: Regulator can be put into bypass mode
|
|
*/
|
|
|
|
#define REGULATOR_CHANGE_VOLTAGE 0x1
|
|
#define REGULATOR_CHANGE_CURRENT 0x2
|
|
#define REGULATOR_CHANGE_MODE 0x4
|
|
#define REGULATOR_CHANGE_STATUS 0x8
|
|
#define REGULATOR_CHANGE_DRMS 0x10
|
|
#define REGULATOR_CHANGE_BYPASS 0x20
|
|
|
|
/*
|
|
* operations in suspend mode
|
|
* DO_NOTHING_IN_SUSPEND - the default value
|
|
* DISABLE_IN_SUSPEND - turn off regulator in suspend states
|
|
* ENABLE_IN_SUSPEND - keep regulator on in suspend states
|
|
*/
|
|
#define DO_NOTHING_IN_SUSPEND 0
|
|
#define DISABLE_IN_SUSPEND 1
|
|
#define ENABLE_IN_SUSPEND 2
|
|
|
|
/* Regulator active discharge flags */
|
|
enum regulator_active_discharge {
|
|
REGULATOR_ACTIVE_DISCHARGE_DEFAULT,
|
|
REGULATOR_ACTIVE_DISCHARGE_DISABLE,
|
|
REGULATOR_ACTIVE_DISCHARGE_ENABLE,
|
|
};
|
|
|
|
/**
|
|
* struct regulator_state - regulator state during low power system states
|
|
*
|
|
* This describes a regulators state during a system wide low power
|
|
* state. One of enabled or disabled must be set for the
|
|
* configuration to be applied.
|
|
*
|
|
* @uV: Default operating voltage during suspend, it can be adjusted
|
|
* among <min_uV, max_uV>.
|
|
* @min_uV: Minimum suspend voltage may be set.
|
|
* @max_uV: Maximum suspend voltage may be set.
|
|
* @mode: Operating mode during suspend.
|
|
* @enabled: operations during suspend.
|
|
* - DO_NOTHING_IN_SUSPEND
|
|
* - DISABLE_IN_SUSPEND
|
|
* - ENABLE_IN_SUSPEND
|
|
* @changeable: Is this state can be switched between enabled/disabled,
|
|
*/
|
|
struct regulator_state {
|
|
int uV;
|
|
int min_uV;
|
|
int max_uV;
|
|
unsigned int mode;
|
|
int enabled;
|
|
bool changeable;
|
|
};
|
|
|
|
/**
|
|
* struct regulation_constraints - regulator operating constraints.
|
|
*
|
|
* This struct describes regulator and board/machine specific constraints.
|
|
*
|
|
* @name: Descriptive name for the constraints, used for display purposes.
|
|
*
|
|
* @min_uV: Smallest voltage consumers may set.
|
|
* @max_uV: Largest voltage consumers may set.
|
|
* @uV_offset: Offset applied to voltages from consumer to compensate for
|
|
* voltage drops.
|
|
*
|
|
* @min_uA: Smallest current consumers may set.
|
|
* @max_uA: Largest current consumers may set.
|
|
* @ilim_uA: Maximum input current.
|
|
* @system_load: Load that isn't captured by any consumer requests.
|
|
*
|
|
* @max_spread: Max possible spread between coupled regulators
|
|
* @max_uV_step: Max possible step change in voltage
|
|
* @valid_modes_mask: Mask of modes which may be configured by consumers.
|
|
* @valid_ops_mask: Operations which may be performed by consumers.
|
|
*
|
|
* @always_on: Set if the regulator should never be disabled.
|
|
* @boot_on: Set if the regulator is enabled when the system is initially
|
|
* started. If the regulator is not enabled by the hardware or
|
|
* bootloader then it will be enabled when the constraints are
|
|
* applied.
|
|
* @apply_uV: Apply the voltage constraint when initialising.
|
|
* @ramp_disable: Disable ramp delay when initialising or when setting voltage.
|
|
* @soft_start: Enable soft start so that voltage ramps slowly.
|
|
* @pull_down: Enable pull down when regulator is disabled.
|
|
* @over_current_protection: Auto disable on over current event.
|
|
*
|
|
* @input_uV: Input voltage for regulator when supplied by another regulator.
|
|
*
|
|
* @state_disk: State for regulator when system is suspended in disk mode.
|
|
* @state_mem: State for regulator when system is suspended in mem mode.
|
|
* @state_standby: State for regulator when system is suspended in standby
|
|
* mode.
|
|
* @initial_state: Suspend state to set by default.
|
|
* @initial_mode: Mode to set at startup.
|
|
* @ramp_delay: Time to settle down after voltage change (unit: uV/us)
|
|
* @settling_time: Time to settle down after voltage change when voltage
|
|
* change is non-linear (unit: microseconds).
|
|
* @settling_time_up: Time to settle down after voltage increase when voltage
|
|
* change is non-linear (unit: microseconds).
|
|
* @settling_time_down : Time to settle down after voltage decrease when
|
|
* voltage change is non-linear (unit: microseconds).
|
|
* @active_discharge: Enable/disable active discharge. The enum
|
|
* regulator_active_discharge values are used for
|
|
* initialisation.
|
|
* @enable_time: Turn-on time of the rails (unit: microseconds)
|
|
*/
|
|
struct regulation_constraints {
|
|
|
|
const char *name;
|
|
|
|
/* voltage output range (inclusive) - for voltage control */
|
|
int min_uV;
|
|
int max_uV;
|
|
|
|
int uV_offset;
|
|
|
|
/* current output range (inclusive) - for current control */
|
|
int min_uA;
|
|
int max_uA;
|
|
int ilim_uA;
|
|
|
|
int system_load;
|
|
|
|
/* used for coupled regulators */
|
|
u32 *max_spread;
|
|
|
|
/* used for changing voltage in steps */
|
|
int max_uV_step;
|
|
|
|
/* valid regulator operating modes for this machine */
|
|
unsigned int valid_modes_mask;
|
|
|
|
/* valid operations for regulator on this machine */
|
|
unsigned int valid_ops_mask;
|
|
|
|
/* regulator input voltage - only if supply is another regulator */
|
|
int input_uV;
|
|
|
|
/* regulator suspend states for global PMIC STANDBY/HIBERNATE */
|
|
struct regulator_state state_disk;
|
|
struct regulator_state state_mem;
|
|
struct regulator_state state_standby;
|
|
suspend_state_t initial_state; /* suspend state to set at init */
|
|
|
|
/* mode to set on startup */
|
|
unsigned int initial_mode;
|
|
|
|
unsigned int ramp_delay;
|
|
unsigned int settling_time;
|
|
unsigned int settling_time_up;
|
|
unsigned int settling_time_down;
|
|
unsigned int enable_time;
|
|
|
|
unsigned int active_discharge;
|
|
|
|
/* constraint flags */
|
|
unsigned always_on:1; /* regulator never off when system is on */
|
|
unsigned boot_on:1; /* bootloader/firmware enabled regulator */
|
|
unsigned apply_uV:1; /* apply uV constraint if min == max */
|
|
unsigned ramp_disable:1; /* disable ramp delay */
|
|
unsigned soft_start:1; /* ramp voltage slowly */
|
|
unsigned pull_down:1; /* pull down resistor when regulator off */
|
|
unsigned over_current_protection:1; /* auto disable on over current */
|
|
};
|
|
|
|
/**
|
|
* struct regulator_consumer_supply - supply -> device mapping
|
|
*
|
|
* This maps a supply name to a device. Use of dev_name allows support for
|
|
* buses which make struct device available late such as I2C.
|
|
*
|
|
* @dev_name: Result of dev_name() for the consumer.
|
|
* @supply: Name for the supply.
|
|
*/
|
|
struct regulator_consumer_supply {
|
|
const char *dev_name; /* dev_name() for consumer */
|
|
const char *supply; /* consumer supply - e.g. "vcc" */
|
|
};
|
|
|
|
/* Initialize struct regulator_consumer_supply */
|
|
#define REGULATOR_SUPPLY(_name, _dev_name) \
|
|
{ \
|
|
.supply = _name, \
|
|
.dev_name = _dev_name, \
|
|
}
|
|
|
|
/**
|
|
* struct regulator_init_data - regulator platform initialisation data.
|
|
*
|
|
* Initialisation constraints, our supply and consumers supplies.
|
|
*
|
|
* @supply_regulator: Parent regulator. Specified using the regulator name
|
|
* as it appears in the name field in sysfs, which can
|
|
* be explicitly set using the constraints field 'name'.
|
|
*
|
|
* @constraints: Constraints. These must be specified for the regulator to
|
|
* be usable.
|
|
* @num_consumer_supplies: Number of consumer device supplies.
|
|
* @consumer_supplies: Consumer device supply configuration.
|
|
*
|
|
* @regulator_init: Callback invoked when the regulator has been registered.
|
|
* @driver_data: Data passed to regulator_init.
|
|
*/
|
|
struct regulator_init_data {
|
|
const char *supply_regulator; /* or NULL for system supply */
|
|
|
|
struct regulation_constraints constraints;
|
|
|
|
int num_consumer_supplies;
|
|
struct regulator_consumer_supply *consumer_supplies;
|
|
|
|
/* optional regulator machine specific init */
|
|
int (*regulator_init)(void *driver_data);
|
|
void *driver_data; /* core does not touch this */
|
|
};
|
|
|
|
#ifdef CONFIG_REGULATOR
|
|
void regulator_has_full_constraints(void);
|
|
#else
|
|
static inline void regulator_has_full_constraints(void)
|
|
{
|
|
}
|
|
#endif
|
|
|
|
static inline int regulator_suspend_prepare(suspend_state_t state)
|
|
{
|
|
return 0;
|
|
}
|
|
static inline int regulator_suspend_finish(void)
|
|
{
|
|
return 0;
|
|
}
|
|
|
|
#endif
|