linux-sg2042/drivers/pinctrl/pinctrl-coh901.c

976 lines
26 KiB
C

/*
* U300 GPIO module.
*
* Copyright (C) 2007-2011 ST-Ericsson AB
* License terms: GNU General Public License (GPL) version 2
* This can driver either of the two basic GPIO cores
* available in the U300 platforms:
* COH 901 335 - Used in DB3150 (U300 1.0) and DB3200 (U330 1.0)
* COH 901 571/3 - Used in DB3210 (U365 2.0) and DB3350 (U335 1.0)
* Author: Linus Walleij <linus.walleij@linaro.org>
* Author: Jonas Aaberg <jonas.aberg@stericsson.com>
*/
#include <linux/module.h>
#include <linux/irq.h>
#include <linux/interrupt.h>
#include <linux/delay.h>
#include <linux/errno.h>
#include <linux/io.h>
#include <linux/clk.h>
#include <linux/err.h>
#include <linux/platform_device.h>
#include <linux/gpio.h>
#include <linux/list.h>
#include <linux/slab.h>
#include <linux/pinctrl/consumer.h>
#include <linux/pinctrl/pinconf-generic.h>
#include <mach/gpio-u300.h>
#include "pinctrl-coh901.h"
/*
* Register definitions for COH 901 335 variant
*/
#define U300_335_PORT_STRIDE (0x1C)
/* Port X Pin Data Register 32bit, this is both input and output (R/W) */
#define U300_335_PXPDIR (0x00)
#define U300_335_PXPDOR (0x00)
/* Port X Pin Config Register 32bit (R/W) */
#define U300_335_PXPCR (0x04)
/* This register layout is the same in both blocks */
#define U300_GPIO_PXPCR_ALL_PINS_MODE_MASK (0x0000FFFFUL)
#define U300_GPIO_PXPCR_PIN_MODE_MASK (0x00000003UL)
#define U300_GPIO_PXPCR_PIN_MODE_SHIFT (0x00000002UL)
#define U300_GPIO_PXPCR_PIN_MODE_INPUT (0x00000000UL)
#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL (0x00000001UL)
#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN (0x00000002UL)
#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE (0x00000003UL)
/* Port X Interrupt Event Register 32bit (R/W) */
#define U300_335_PXIEV (0x08)
/* Port X Interrupt Enable Register 32bit (R/W) */
#define U300_335_PXIEN (0x0C)
/* Port X Interrupt Force Register 32bit (R/W) */
#define U300_335_PXIFR (0x10)
/* Port X Interrupt Config Register 32bit (R/W) */
#define U300_335_PXICR (0x14)
/* This register layout is the same in both blocks */
#define U300_GPIO_PXICR_ALL_IRQ_CONFIG_MASK (0x000000FFUL)
#define U300_GPIO_PXICR_IRQ_CONFIG_MASK (0x00000001UL)
#define U300_GPIO_PXICR_IRQ_CONFIG_FALLING_EDGE (0x00000000UL)
#define U300_GPIO_PXICR_IRQ_CONFIG_RISING_EDGE (0x00000001UL)
/* Port X Pull-up Enable Register 32bit (R/W) */
#define U300_335_PXPER (0x18)
/* This register layout is the same in both blocks */
#define U300_GPIO_PXPER_ALL_PULL_UP_DISABLE_MASK (0x000000FFUL)
#define U300_GPIO_PXPER_PULL_UP_DISABLE (0x00000001UL)
/* Control Register 32bit (R/W) */
#define U300_335_CR (0x54)
#define U300_335_CR_BLOCK_CLOCK_ENABLE (0x00000001UL)
/*
* Register definitions for COH 901 571 / 3 variant
*/
#define U300_571_PORT_STRIDE (0x30)
/*
* Control Register 32bit (R/W)
* bit 15-9 (mask 0x0000FE00) contains the number of cores. 8*cores
* gives the number of GPIO pins.
* bit 8-2 (mask 0x000001FC) contains the core version ID.
*/
#define U300_571_CR (0x00)
#define U300_571_CR_SYNC_SEL_ENABLE (0x00000002UL)
#define U300_571_CR_BLOCK_CLKRQ_ENABLE (0x00000001UL)
/*
* These registers have the same layout and function as the corresponding
* COH 901 335 registers, just at different offset.
*/
#define U300_571_PXPDIR (0x04)
#define U300_571_PXPDOR (0x08)
#define U300_571_PXPCR (0x0C)
#define U300_571_PXPER (0x10)
#define U300_571_PXIEV (0x14)
#define U300_571_PXIEN (0x18)
#define U300_571_PXIFR (0x1C)
#define U300_571_PXICR (0x20)
/* 8 bits per port, no version has more than 7 ports */
#define U300_GPIO_PINS_PER_PORT 8
#define U300_GPIO_MAX (U300_GPIO_PINS_PER_PORT * 7)
struct u300_gpio {
struct gpio_chip chip;
struct list_head port_list;
struct clk *clk;
struct resource *memres;
void __iomem *base;
struct device *dev;
int irq_base;
u32 stride;
/* Register offsets */
u32 pcr;
u32 dor;
u32 dir;
u32 per;
u32 icr;
u32 ien;
u32 iev;
};
struct u300_gpio_port {
struct list_head node;
struct u300_gpio *gpio;
char name[8];
int irq;
int number;
u8 toggle_edge_mode;
};
/*
* Macro to expand to read a specific register found in the "gpio"
* struct. It requires the struct u300_gpio *gpio variable to exist in
* its context. It calculates the port offset from the given pin
* offset, muliplies by the port stride and adds the register offset
* so it provides a pointer to the desired register.
*/
#define U300_PIN_REG(pin, reg) \
(gpio->base + (pin >> 3) * gpio->stride + gpio->reg)
/*
* Provides a bitmask for a specific gpio pin inside an 8-bit GPIO
* register.
*/
#define U300_PIN_BIT(pin) \
(1 << (pin & 0x07))
struct u300_gpio_confdata {
u16 bias_mode;
bool output;
int outval;
};
/* BS335 has seven ports of 8 bits each = GPIO pins 0..55 */
#define BS335_GPIO_NUM_PORTS 7
/* BS365 has five ports of 8 bits each = GPIO pins 0..39 */
#define BS365_GPIO_NUM_PORTS 5
#define U300_FLOATING_INPUT { \
.bias_mode = PIN_CONFIG_BIAS_HIGH_IMPEDANCE, \
.output = false, \
}
#define U300_PULL_UP_INPUT { \
.bias_mode = PIN_CONFIG_BIAS_PULL_UP, \
.output = false, \
}
#define U300_OUTPUT_LOW { \
.output = true, \
.outval = 0, \
}
#define U300_OUTPUT_HIGH { \
.output = true, \
.outval = 1, \
}
/* Initial configuration */
static const struct __initdata u300_gpio_confdata
bs335_gpio_config[BS335_GPIO_NUM_PORTS][U300_GPIO_PINS_PER_PORT] = {
/* Port 0, pins 0-7 */
{
U300_FLOATING_INPUT,
U300_OUTPUT_HIGH,
U300_FLOATING_INPUT,
U300_OUTPUT_LOW,
U300_OUTPUT_LOW,
U300_OUTPUT_LOW,
U300_OUTPUT_LOW,
U300_OUTPUT_LOW,
},
/* Port 1, pins 0-7 */
{
U300_OUTPUT_LOW,
U300_OUTPUT_LOW,
U300_OUTPUT_LOW,
U300_PULL_UP_INPUT,
U300_FLOATING_INPUT,
U300_OUTPUT_HIGH,
U300_OUTPUT_LOW,
U300_OUTPUT_LOW,
},
/* Port 2, pins 0-7 */
{
U300_FLOATING_INPUT,
U300_FLOATING_INPUT,
U300_FLOATING_INPUT,
U300_FLOATING_INPUT,
U300_OUTPUT_LOW,
U300_PULL_UP_INPUT,
U300_OUTPUT_LOW,
U300_PULL_UP_INPUT,
},
/* Port 3, pins 0-7 */
{
U300_PULL_UP_INPUT,
U300_OUTPUT_LOW,
U300_FLOATING_INPUT,
U300_FLOATING_INPUT,
U300_FLOATING_INPUT,
U300_FLOATING_INPUT,
U300_FLOATING_INPUT,
U300_FLOATING_INPUT,
},
/* Port 4, pins 0-7 */
{
U300_FLOATING_INPUT,
U300_FLOATING_INPUT,
U300_FLOATING_INPUT,
U300_FLOATING_INPUT,
U300_FLOATING_INPUT,
U300_FLOATING_INPUT,
U300_FLOATING_INPUT,
U300_FLOATING_INPUT,
},
/* Port 5, pins 0-7 */
{
U300_FLOATING_INPUT,
U300_FLOATING_INPUT,
U300_FLOATING_INPUT,
U300_FLOATING_INPUT,
U300_FLOATING_INPUT,
U300_FLOATING_INPUT,
U300_FLOATING_INPUT,
U300_FLOATING_INPUT,
},
/* Port 6, pind 0-7 */
{
U300_FLOATING_INPUT,
U300_FLOATING_INPUT,
U300_FLOATING_INPUT,
U300_FLOATING_INPUT,
U300_FLOATING_INPUT,
U300_FLOATING_INPUT,
U300_FLOATING_INPUT,
U300_FLOATING_INPUT,
}
};
static const struct __initdata u300_gpio_confdata
bs365_gpio_config[BS365_GPIO_NUM_PORTS][U300_GPIO_PINS_PER_PORT] = {
/* Port 0, pins 0-7 */
{
U300_FLOATING_INPUT,
U300_OUTPUT_LOW,
U300_FLOATING_INPUT,
U300_OUTPUT_LOW,
U300_OUTPUT_LOW,
U300_OUTPUT_LOW,
U300_PULL_UP_INPUT,
U300_FLOATING_INPUT,
},
/* Port 1, pins 0-7 */
{
U300_OUTPUT_LOW,
U300_FLOATING_INPUT,
U300_OUTPUT_LOW,
U300_FLOATING_INPUT,
U300_FLOATING_INPUT,
U300_OUTPUT_HIGH,
U300_OUTPUT_LOW,
U300_OUTPUT_LOW,
},
/* Port 2, pins 0-7 */
{
U300_FLOATING_INPUT,
U300_PULL_UP_INPUT,
U300_OUTPUT_LOW,
U300_OUTPUT_LOW,
U300_PULL_UP_INPUT,
U300_PULL_UP_INPUT,
U300_PULL_UP_INPUT,
U300_PULL_UP_INPUT,
},
/* Port 3, pins 0-7 */
{
U300_PULL_UP_INPUT,
U300_PULL_UP_INPUT,
U300_PULL_UP_INPUT,
U300_PULL_UP_INPUT,
U300_PULL_UP_INPUT,
U300_PULL_UP_INPUT,
U300_PULL_UP_INPUT,
U300_PULL_UP_INPUT,
},
/* Port 4, pins 0-7 */
{
U300_PULL_UP_INPUT,
U300_PULL_UP_INPUT,
U300_PULL_UP_INPUT,
U300_PULL_UP_INPUT,
/* These 4 pins doesn't exist on DB3210 */
U300_OUTPUT_LOW,
U300_OUTPUT_LOW,
U300_OUTPUT_LOW,
U300_OUTPUT_LOW,
}
};
/**
* to_u300_gpio() - get the pointer to u300_gpio
* @chip: the gpio chip member of the structure u300_gpio
*/
static inline struct u300_gpio *to_u300_gpio(struct gpio_chip *chip)
{
return container_of(chip, struct u300_gpio, chip);
}
static int u300_gpio_request(struct gpio_chip *chip, unsigned offset)
{
/*
* Map back to global GPIO space and request muxing, the direction
* parameter does not matter for this controller.
*/
int gpio = chip->base + offset;
return pinctrl_request_gpio(gpio);
}
static void u300_gpio_free(struct gpio_chip *chip, unsigned offset)
{
int gpio = chip->base + offset;
pinctrl_free_gpio(gpio);
}
static int u300_gpio_get(struct gpio_chip *chip, unsigned offset)
{
struct u300_gpio *gpio = to_u300_gpio(chip);
return readl(U300_PIN_REG(offset, dir)) & U300_PIN_BIT(offset);
}
static void u300_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
{
struct u300_gpio *gpio = to_u300_gpio(chip);
unsigned long flags;
u32 val;
local_irq_save(flags);
val = readl(U300_PIN_REG(offset, dor));
if (value)
writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, dor));
else
writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, dor));
local_irq_restore(flags);
}
static int u300_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
{
struct u300_gpio *gpio = to_u300_gpio(chip);
unsigned long flags;
u32 val;
local_irq_save(flags);
val = readl(U300_PIN_REG(offset, pcr));
/* Mask out this pin, note 2 bits per setting */
val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK << ((offset & 0x07) << 1));
writel(val, U300_PIN_REG(offset, pcr));
local_irq_restore(flags);
return 0;
}
static int u300_gpio_direction_output(struct gpio_chip *chip, unsigned offset,
int value)
{
struct u300_gpio *gpio = to_u300_gpio(chip);
unsigned long flags;
u32 oldmode;
u32 val;
local_irq_save(flags);
val = readl(U300_PIN_REG(offset, pcr));
/*
* Drive mode must be set by the special mode set function, set
* push/pull mode by default if no mode has been selected.
*/
oldmode = val & (U300_GPIO_PXPCR_PIN_MODE_MASK <<
((offset & 0x07) << 1));
/* mode = 0 means input, else some mode is already set */
if (oldmode == 0) {
val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK <<
((offset & 0x07) << 1));
val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL
<< ((offset & 0x07) << 1));
writel(val, U300_PIN_REG(offset, pcr));
}
u300_gpio_set(chip, offset, value);
local_irq_restore(flags);
return 0;
}
static int u300_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
{
struct u300_gpio *gpio = to_u300_gpio(chip);
int retirq = gpio->irq_base + offset;
dev_dbg(gpio->dev, "request IRQ for GPIO %d, return %d\n", offset,
retirq);
return retirq;
}
/* Returning -EINVAL means "supported but not available" */
int u300_gpio_config_get(struct gpio_chip *chip,
unsigned offset,
unsigned long *config)
{
struct u300_gpio *gpio = to_u300_gpio(chip);
enum pin_config_param param = (enum pin_config_param) *config;
bool biasmode;
u32 drmode;
/* One bit per pin, clamp to bool range */
biasmode = !!(readl(U300_PIN_REG(offset, per)) & U300_PIN_BIT(offset));
/* Mask out the two bits for this pin and shift to bits 0,1 */
drmode = readl(U300_PIN_REG(offset, pcr));
drmode &= (U300_GPIO_PXPCR_PIN_MODE_MASK << ((offset & 0x07) << 1));
drmode >>= ((offset & 0x07) << 1);
switch(param) {
case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
*config = 0;
if (biasmode)
return 0;
else
return -EINVAL;
break;
case PIN_CONFIG_BIAS_PULL_UP:
*config = 0;
if (!biasmode)
return 0;
else
return -EINVAL;
break;
case PIN_CONFIG_DRIVE_PUSH_PULL:
*config = 0;
if (drmode == U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL)
return 0;
else
return -EINVAL;
break;
case PIN_CONFIG_DRIVE_OPEN_DRAIN:
*config = 0;
if (drmode == U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN)
return 0;
else
return -EINVAL;
break;
case PIN_CONFIG_DRIVE_OPEN_SOURCE:
*config = 0;
if (drmode == U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE)
return 0;
else
return -EINVAL;
break;
default:
break;
}
return -ENOTSUPP;
}
int u300_gpio_config_set(struct gpio_chip *chip, unsigned offset,
enum pin_config_param param)
{
struct u300_gpio *gpio = to_u300_gpio(chip);
unsigned long flags;
u32 val;
local_irq_save(flags);
switch (param) {
case PIN_CONFIG_BIAS_DISABLE:
case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
val = readl(U300_PIN_REG(offset, per));
writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, per));
break;
case PIN_CONFIG_BIAS_PULL_UP:
val = readl(U300_PIN_REG(offset, per));
writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, per));
break;
case PIN_CONFIG_DRIVE_PUSH_PULL:
val = readl(U300_PIN_REG(offset, pcr));
val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK
<< ((offset & 0x07) << 1));
val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL
<< ((offset & 0x07) << 1));
writel(val, U300_PIN_REG(offset, pcr));
break;
case PIN_CONFIG_DRIVE_OPEN_DRAIN:
val = readl(U300_PIN_REG(offset, pcr));
val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK
<< ((offset & 0x07) << 1));
val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN
<< ((offset & 0x07) << 1));
writel(val, U300_PIN_REG(offset, pcr));
break;
case PIN_CONFIG_DRIVE_OPEN_SOURCE:
val = readl(U300_PIN_REG(offset, pcr));
val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK
<< ((offset & 0x07) << 1));
val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE
<< ((offset & 0x07) << 1));
writel(val, U300_PIN_REG(offset, pcr));
break;
default:
local_irq_restore(flags);
dev_err(gpio->dev, "illegal configuration requested\n");
return -EINVAL;
}
local_irq_restore(flags);
return 0;
}
static struct gpio_chip u300_gpio_chip = {
.label = "u300-gpio-chip",
.owner = THIS_MODULE,
.request = u300_gpio_request,
.free = u300_gpio_free,
.get = u300_gpio_get,
.set = u300_gpio_set,
.direction_input = u300_gpio_direction_input,
.direction_output = u300_gpio_direction_output,
.to_irq = u300_gpio_to_irq,
};
static void u300_toggle_trigger(struct u300_gpio *gpio, unsigned offset)
{
u32 val;
val = readl(U300_PIN_REG(offset, icr));
/* Set mode depending on state */
if (u300_gpio_get(&gpio->chip, offset)) {
/* High now, let's trigger on falling edge next then */
writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, icr));
dev_dbg(gpio->dev, "next IRQ on falling edge on pin %d\n",
offset);
} else {
/* Low now, let's trigger on rising edge next then */
writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, icr));
dev_dbg(gpio->dev, "next IRQ on rising edge on pin %d\n",
offset);
}
}
static int u300_gpio_irq_type(struct irq_data *d, unsigned trigger)
{
struct u300_gpio_port *port = irq_data_get_irq_chip_data(d);
struct u300_gpio *gpio = port->gpio;
int offset = d->irq - gpio->irq_base;
u32 val;
if ((trigger & IRQF_TRIGGER_RISING) &&
(trigger & IRQF_TRIGGER_FALLING)) {
/*
* The GPIO block can only trigger on falling OR rising edges,
* not both. So we need to toggle the mode whenever the pin
* goes from one state to the other with a special state flag
*/
dev_dbg(gpio->dev,
"trigger on both rising and falling edge on pin %d\n",
offset);
port->toggle_edge_mode |= U300_PIN_BIT(offset);
u300_toggle_trigger(gpio, offset);
} else if (trigger & IRQF_TRIGGER_RISING) {
dev_dbg(gpio->dev, "trigger on rising edge on pin %d\n",
offset);
val = readl(U300_PIN_REG(offset, icr));
writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, icr));
port->toggle_edge_mode &= ~U300_PIN_BIT(offset);
} else if (trigger & IRQF_TRIGGER_FALLING) {
dev_dbg(gpio->dev, "trigger on falling edge on pin %d\n",
offset);
val = readl(U300_PIN_REG(offset, icr));
writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, icr));
port->toggle_edge_mode &= ~U300_PIN_BIT(offset);
}
return 0;
}
static void u300_gpio_irq_enable(struct irq_data *d)
{
struct u300_gpio_port *port = irq_data_get_irq_chip_data(d);
struct u300_gpio *gpio = port->gpio;
int offset = d->irq - gpio->irq_base;
u32 val;
unsigned long flags;
local_irq_save(flags);
val = readl(U300_PIN_REG(offset, ien));
writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, ien));
local_irq_restore(flags);
}
static void u300_gpio_irq_disable(struct irq_data *d)
{
struct u300_gpio_port *port = irq_data_get_irq_chip_data(d);
struct u300_gpio *gpio = port->gpio;
int offset = d->irq - gpio->irq_base;
u32 val;
unsigned long flags;
local_irq_save(flags);
val = readl(U300_PIN_REG(offset, ien));
writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, ien));
local_irq_restore(flags);
}
static struct irq_chip u300_gpio_irqchip = {
.name = "u300-gpio-irqchip",
.irq_enable = u300_gpio_irq_enable,
.irq_disable = u300_gpio_irq_disable,
.irq_set_type = u300_gpio_irq_type,
};
static void u300_gpio_irq_handler(unsigned irq, struct irq_desc *desc)
{
struct u300_gpio_port *port = irq_get_handler_data(irq);
struct u300_gpio *gpio = port->gpio;
int pinoffset = port->number << 3; /* get the right stride */
unsigned long val;
desc->irq_data.chip->irq_ack(&desc->irq_data);
/* Read event register */
val = readl(U300_PIN_REG(pinoffset, iev));
/* Mask relevant bits */
val &= 0xFFU; /* 8 bits per port */
/* ACK IRQ (clear event) */
writel(val, U300_PIN_REG(pinoffset, iev));
/* Call IRQ handler */
if (val != 0) {
int irqoffset;
for_each_set_bit(irqoffset, &val, U300_GPIO_PINS_PER_PORT) {
int pin_irq = gpio->irq_base + (port->number << 3)
+ irqoffset;
int offset = pinoffset + irqoffset;
dev_dbg(gpio->dev, "GPIO IRQ %d on pin %d\n",
pin_irq, offset);
generic_handle_irq(pin_irq);
/*
* Triggering IRQ on both rising and falling edge
* needs mockery
*/
if (port->toggle_edge_mode & U300_PIN_BIT(offset))
u300_toggle_trigger(gpio, offset);
}
}
desc->irq_data.chip->irq_unmask(&desc->irq_data);
}
static void __init u300_gpio_init_pin(struct u300_gpio *gpio,
int offset,
const struct u300_gpio_confdata *conf)
{
/* Set mode: input or output */
if (conf->output) {
u300_gpio_direction_output(&gpio->chip, offset, conf->outval);
/* Deactivate bias mode for output */
u300_gpio_config_set(&gpio->chip, offset,
PIN_CONFIG_BIAS_HIGH_IMPEDANCE);
/* Set drive mode for output */
u300_gpio_config_set(&gpio->chip, offset,
PIN_CONFIG_DRIVE_PUSH_PULL);
dev_dbg(gpio->dev, "set up pin %d as output, value: %d\n",
offset, conf->outval);
} else {
u300_gpio_direction_input(&gpio->chip, offset);
/* Always set output low on input pins */
u300_gpio_set(&gpio->chip, offset, 0);
/* Set bias mode for input */
u300_gpio_config_set(&gpio->chip, offset, conf->bias_mode);
dev_dbg(gpio->dev, "set up pin %d as input, bias: %04x\n",
offset, conf->bias_mode);
}
}
static void __init u300_gpio_init_coh901571(struct u300_gpio *gpio,
struct u300_gpio_platform *plat)
{
int i, j;
/* Write default config and values to all pins */
for (i = 0; i < plat->ports; i++) {
for (j = 0; j < 8; j++) {
const struct u300_gpio_confdata *conf;
int offset = (i*8) + j;
if (plat->variant == U300_GPIO_COH901571_3_BS335)
conf = &bs335_gpio_config[i][j];
else if (plat->variant == U300_GPIO_COH901571_3_BS365)
conf = &bs365_gpio_config[i][j];
else
break;
u300_gpio_init_pin(gpio, offset, conf);
}
}
}
static inline void u300_gpio_free_ports(struct u300_gpio *gpio)
{
struct u300_gpio_port *port;
struct list_head *p, *n;
list_for_each_safe(p, n, &gpio->port_list) {
port = list_entry(p, struct u300_gpio_port, node);
list_del(&port->node);
kfree(port);
}
}
static int __init u300_gpio_probe(struct platform_device *pdev)
{
struct u300_gpio_platform *plat = dev_get_platdata(&pdev->dev);
struct u300_gpio *gpio;
int err = 0;
int portno;
u32 val;
u32 ifr;
int i;
gpio = kzalloc(sizeof(struct u300_gpio), GFP_KERNEL);
if (gpio == NULL) {
dev_err(&pdev->dev, "failed to allocate memory\n");
return -ENOMEM;
}
gpio->chip = u300_gpio_chip;
gpio->chip.ngpio = plat->ports * U300_GPIO_PINS_PER_PORT;
gpio->irq_base = plat->gpio_irq_base;
gpio->chip.dev = &pdev->dev;
gpio->chip.base = plat->gpio_base;
gpio->dev = &pdev->dev;
/* Get GPIO clock */
gpio->clk = clk_get(gpio->dev, NULL);
if (IS_ERR(gpio->clk)) {
err = PTR_ERR(gpio->clk);
dev_err(gpio->dev, "could not get GPIO clock\n");
goto err_no_clk;
}
err = clk_enable(gpio->clk);
if (err) {
dev_err(gpio->dev, "could not enable GPIO clock\n");
goto err_no_clk_enable;
}
gpio->memres = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!gpio->memres) {
dev_err(gpio->dev, "could not get GPIO memory resource\n");
err = -ENODEV;
goto err_no_resource;
}
if (!request_mem_region(gpio->memres->start,
resource_size(gpio->memres),
"GPIO Controller")) {
err = -ENODEV;
goto err_no_ioregion;
}
gpio->base = ioremap(gpio->memres->start, resource_size(gpio->memres));
if (!gpio->base) {
err = -ENOMEM;
goto err_no_ioremap;
}
if (plat->variant == U300_GPIO_COH901335) {
dev_info(gpio->dev,
"initializing GPIO Controller COH 901 335\n");
gpio->stride = U300_335_PORT_STRIDE;
gpio->pcr = U300_335_PXPCR;
gpio->dor = U300_335_PXPDOR;
gpio->dir = U300_335_PXPDIR;
gpio->per = U300_335_PXPER;
gpio->icr = U300_335_PXICR;
gpio->ien = U300_335_PXIEN;
gpio->iev = U300_335_PXIEV;
ifr = U300_335_PXIFR;
/* Turn on the GPIO block */
writel(U300_335_CR_BLOCK_CLOCK_ENABLE,
gpio->base + U300_335_CR);
} else if (plat->variant == U300_GPIO_COH901571_3_BS335 ||
plat->variant == U300_GPIO_COH901571_3_BS365) {
dev_info(gpio->dev,
"initializing GPIO Controller COH 901 571/3\n");
gpio->stride = U300_571_PORT_STRIDE;
gpio->pcr = U300_571_PXPCR;
gpio->dor = U300_571_PXPDOR;
gpio->dir = U300_571_PXPDIR;
gpio->per = U300_571_PXPER;
gpio->icr = U300_571_PXICR;
gpio->ien = U300_571_PXIEN;
gpio->iev = U300_571_PXIEV;
ifr = U300_571_PXIFR;
val = readl(gpio->base + U300_571_CR);
dev_info(gpio->dev, "COH901571/3 block version: %d, " \
"number of cores: %d totalling %d pins\n",
((val & 0x000001FC) >> 2),
((val & 0x0000FE00) >> 9),
((val & 0x0000FE00) >> 9) * 8);
writel(U300_571_CR_BLOCK_CLKRQ_ENABLE,
gpio->base + U300_571_CR);
u300_gpio_init_coh901571(gpio, plat);
} else {
dev_err(gpio->dev, "unknown block variant\n");
err = -ENODEV;
goto err_unknown_variant;
}
/* Add each port with its IRQ separately */
INIT_LIST_HEAD(&gpio->port_list);
for (portno = 0 ; portno < plat->ports; portno++) {
struct u300_gpio_port *port =
kmalloc(sizeof(struct u300_gpio_port), GFP_KERNEL);
if (!port) {
dev_err(gpio->dev, "out of memory\n");
err = -ENOMEM;
goto err_no_port;
}
snprintf(port->name, 8, "gpio%d", portno);
port->number = portno;
port->gpio = gpio;
port->irq = platform_get_irq_byname(pdev,
port->name);
dev_dbg(gpio->dev, "register IRQ %d for %s\n", port->irq,
port->name);
irq_set_chained_handler(port->irq, u300_gpio_irq_handler);
irq_set_handler_data(port->irq, port);
/* For each GPIO pin set the unique IRQ handler */
for (i = 0; i < U300_GPIO_PINS_PER_PORT; i++) {
int irqno = gpio->irq_base + (portno << 3) + i;
dev_dbg(gpio->dev, "handler for IRQ %d on %s\n",
irqno, port->name);
irq_set_chip_and_handler(irqno, &u300_gpio_irqchip,
handle_simple_irq);
set_irq_flags(irqno, IRQF_VALID);
irq_set_chip_data(irqno, port);
}
/* Turns off irq force (test register) for this port */
writel(0x0, gpio->base + portno * gpio->stride + ifr);
list_add_tail(&port->node, &gpio->port_list);
}
dev_dbg(gpio->dev, "initialized %d GPIO ports\n", portno);
err = gpiochip_add(&gpio->chip);
if (err) {
dev_err(gpio->dev, "unable to add gpiochip: %d\n", err);
goto err_no_chip;
}
/* Spawn pin controller device as child of the GPIO, pass gpio chip */
plat->pinctrl_device->dev.platform_data = &gpio->chip;
err = platform_device_register(plat->pinctrl_device);
if (err)
goto err_no_pinctrl;
platform_set_drvdata(pdev, gpio);
return 0;
err_no_pinctrl:
err = gpiochip_remove(&gpio->chip);
err_no_chip:
err_no_port:
u300_gpio_free_ports(gpio);
err_unknown_variant:
iounmap(gpio->base);
err_no_ioremap:
release_mem_region(gpio->memres->start, resource_size(gpio->memres));
err_no_ioregion:
err_no_resource:
clk_disable(gpio->clk);
err_no_clk_enable:
clk_put(gpio->clk);
err_no_clk:
kfree(gpio);
dev_info(&pdev->dev, "module ERROR:%d\n", err);
return err;
}
static int __exit u300_gpio_remove(struct platform_device *pdev)
{
struct u300_gpio_platform *plat = dev_get_platdata(&pdev->dev);
struct u300_gpio *gpio = platform_get_drvdata(pdev);
int err;
/* Turn off the GPIO block */
if (plat->variant == U300_GPIO_COH901335)
writel(0x00000000U, gpio->base + U300_335_CR);
if (plat->variant == U300_GPIO_COH901571_3_BS335 ||
plat->variant == U300_GPIO_COH901571_3_BS365)
writel(0x00000000U, gpio->base + U300_571_CR);
err = gpiochip_remove(&gpio->chip);
if (err < 0) {
dev_err(gpio->dev, "unable to remove gpiochip: %d\n", err);
return err;
}
u300_gpio_free_ports(gpio);
iounmap(gpio->base);
release_mem_region(gpio->memres->start,
resource_size(gpio->memres));
clk_disable(gpio->clk);
clk_put(gpio->clk);
platform_set_drvdata(pdev, NULL);
kfree(gpio);
return 0;
}
static struct platform_driver u300_gpio_driver = {
.driver = {
.name = "u300-gpio",
},
.remove = __exit_p(u300_gpio_remove),
};
static int __init u300_gpio_init(void)
{
return platform_driver_probe(&u300_gpio_driver, u300_gpio_probe);
}
static void __exit u300_gpio_exit(void)
{
platform_driver_unregister(&u300_gpio_driver);
}
arch_initcall(u300_gpio_init);
module_exit(u300_gpio_exit);
MODULE_AUTHOR("Linus Walleij <linus.walleij@stericsson.com>");
MODULE_DESCRIPTION("ST-Ericsson AB COH 901 335/COH 901 571/3 GPIO driver");
MODULE_LICENSE("GPL");