1993 lines
55 KiB
C
1993 lines
55 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* Lantiq / Intel GSWIP switch driver for VRX200 SoCs
|
|
*
|
|
* Copyright (C) 2010 Lantiq Deutschland
|
|
* Copyright (C) 2012 John Crispin <john@phrozen.org>
|
|
* Copyright (C) 2017 - 2019 Hauke Mehrtens <hauke@hauke-m.de>
|
|
*
|
|
* The VLAN and bridge model the GSWIP hardware uses does not directly
|
|
* matches the model DSA uses.
|
|
*
|
|
* The hardware has 64 possible table entries for bridges with one VLAN
|
|
* ID, one flow id and a list of ports for each bridge. All entries which
|
|
* match the same flow ID are combined in the mac learning table, they
|
|
* act as one global bridge.
|
|
* The hardware does not support VLAN filter on the port, but on the
|
|
* bridge, this driver converts the DSA model to the hardware.
|
|
*
|
|
* The CPU gets all the exception frames which do not match any forwarding
|
|
* rule and the CPU port is also added to all bridges. This makes it possible
|
|
* to handle all the special cases easily in software.
|
|
* At the initialization the driver allocates one bridge table entry for
|
|
* each switch port which is used when the port is used without an
|
|
* explicit bridge. This prevents the frames from being forwarded
|
|
* between all LAN ports by default.
|
|
*/
|
|
|
|
#include <linux/clk.h>
|
|
#include <linux/etherdevice.h>
|
|
#include <linux/firmware.h>
|
|
#include <linux/if_bridge.h>
|
|
#include <linux/if_vlan.h>
|
|
#include <linux/iopoll.h>
|
|
#include <linux/mfd/syscon.h>
|
|
#include <linux/module.h>
|
|
#include <linux/of_mdio.h>
|
|
#include <linux/of_net.h>
|
|
#include <linux/of_platform.h>
|
|
#include <linux/phy.h>
|
|
#include <linux/phylink.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/regmap.h>
|
|
#include <linux/reset.h>
|
|
#include <net/dsa.h>
|
|
#include <dt-bindings/mips/lantiq_rcu_gphy.h>
|
|
|
|
#include "lantiq_pce.h"
|
|
|
|
/* GSWIP MDIO Registers */
|
|
#define GSWIP_MDIO_GLOB 0x00
|
|
#define GSWIP_MDIO_GLOB_ENABLE BIT(15)
|
|
#define GSWIP_MDIO_CTRL 0x08
|
|
#define GSWIP_MDIO_CTRL_BUSY BIT(12)
|
|
#define GSWIP_MDIO_CTRL_RD BIT(11)
|
|
#define GSWIP_MDIO_CTRL_WR BIT(10)
|
|
#define GSWIP_MDIO_CTRL_PHYAD_MASK 0x1f
|
|
#define GSWIP_MDIO_CTRL_PHYAD_SHIFT 5
|
|
#define GSWIP_MDIO_CTRL_REGAD_MASK 0x1f
|
|
#define GSWIP_MDIO_READ 0x09
|
|
#define GSWIP_MDIO_WRITE 0x0A
|
|
#define GSWIP_MDIO_MDC_CFG0 0x0B
|
|
#define GSWIP_MDIO_MDC_CFG1 0x0C
|
|
#define GSWIP_MDIO_PHYp(p) (0x15 - (p))
|
|
#define GSWIP_MDIO_PHY_LINK_MASK 0x6000
|
|
#define GSWIP_MDIO_PHY_LINK_AUTO 0x0000
|
|
#define GSWIP_MDIO_PHY_LINK_DOWN 0x4000
|
|
#define GSWIP_MDIO_PHY_LINK_UP 0x2000
|
|
#define GSWIP_MDIO_PHY_SPEED_MASK 0x1800
|
|
#define GSWIP_MDIO_PHY_SPEED_AUTO 0x1800
|
|
#define GSWIP_MDIO_PHY_SPEED_M10 0x0000
|
|
#define GSWIP_MDIO_PHY_SPEED_M100 0x0800
|
|
#define GSWIP_MDIO_PHY_SPEED_G1 0x1000
|
|
#define GSWIP_MDIO_PHY_FDUP_MASK 0x0600
|
|
#define GSWIP_MDIO_PHY_FDUP_AUTO 0x0000
|
|
#define GSWIP_MDIO_PHY_FDUP_EN 0x0200
|
|
#define GSWIP_MDIO_PHY_FDUP_DIS 0x0600
|
|
#define GSWIP_MDIO_PHY_FCONTX_MASK 0x0180
|
|
#define GSWIP_MDIO_PHY_FCONTX_AUTO 0x0000
|
|
#define GSWIP_MDIO_PHY_FCONTX_EN 0x0100
|
|
#define GSWIP_MDIO_PHY_FCONTX_DIS 0x0180
|
|
#define GSWIP_MDIO_PHY_FCONRX_MASK 0x0060
|
|
#define GSWIP_MDIO_PHY_FCONRX_AUTO 0x0000
|
|
#define GSWIP_MDIO_PHY_FCONRX_EN 0x0020
|
|
#define GSWIP_MDIO_PHY_FCONRX_DIS 0x0060
|
|
#define GSWIP_MDIO_PHY_ADDR_MASK 0x001f
|
|
#define GSWIP_MDIO_PHY_MASK (GSWIP_MDIO_PHY_ADDR_MASK | \
|
|
GSWIP_MDIO_PHY_FCONRX_MASK | \
|
|
GSWIP_MDIO_PHY_FCONTX_MASK | \
|
|
GSWIP_MDIO_PHY_LINK_MASK | \
|
|
GSWIP_MDIO_PHY_SPEED_MASK | \
|
|
GSWIP_MDIO_PHY_FDUP_MASK)
|
|
|
|
/* GSWIP MII Registers */
|
|
#define GSWIP_MII_CFG0 0x00
|
|
#define GSWIP_MII_CFG1 0x02
|
|
#define GSWIP_MII_CFG5 0x04
|
|
#define GSWIP_MII_CFG_EN BIT(14)
|
|
#define GSWIP_MII_CFG_LDCLKDIS BIT(12)
|
|
#define GSWIP_MII_CFG_MODE_MIIP 0x0
|
|
#define GSWIP_MII_CFG_MODE_MIIM 0x1
|
|
#define GSWIP_MII_CFG_MODE_RMIIP 0x2
|
|
#define GSWIP_MII_CFG_MODE_RMIIM 0x3
|
|
#define GSWIP_MII_CFG_MODE_RGMII 0x4
|
|
#define GSWIP_MII_CFG_MODE_MASK 0xf
|
|
#define GSWIP_MII_CFG_RATE_M2P5 0x00
|
|
#define GSWIP_MII_CFG_RATE_M25 0x10
|
|
#define GSWIP_MII_CFG_RATE_M125 0x20
|
|
#define GSWIP_MII_CFG_RATE_M50 0x30
|
|
#define GSWIP_MII_CFG_RATE_AUTO 0x40
|
|
#define GSWIP_MII_CFG_RATE_MASK 0x70
|
|
#define GSWIP_MII_PCDU0 0x01
|
|
#define GSWIP_MII_PCDU1 0x03
|
|
#define GSWIP_MII_PCDU5 0x05
|
|
#define GSWIP_MII_PCDU_TXDLY_MASK GENMASK(2, 0)
|
|
#define GSWIP_MII_PCDU_RXDLY_MASK GENMASK(9, 7)
|
|
|
|
/* GSWIP Core Registers */
|
|
#define GSWIP_SWRES 0x000
|
|
#define GSWIP_SWRES_R1 BIT(1) /* GSWIP Software reset */
|
|
#define GSWIP_SWRES_R0 BIT(0) /* GSWIP Hardware reset */
|
|
#define GSWIP_VERSION 0x013
|
|
#define GSWIP_VERSION_REV_SHIFT 0
|
|
#define GSWIP_VERSION_REV_MASK GENMASK(7, 0)
|
|
#define GSWIP_VERSION_MOD_SHIFT 8
|
|
#define GSWIP_VERSION_MOD_MASK GENMASK(15, 8)
|
|
#define GSWIP_VERSION_2_0 0x100
|
|
#define GSWIP_VERSION_2_1 0x021
|
|
#define GSWIP_VERSION_2_2 0x122
|
|
#define GSWIP_VERSION_2_2_ETC 0x022
|
|
|
|
#define GSWIP_BM_RAM_VAL(x) (0x043 - (x))
|
|
#define GSWIP_BM_RAM_ADDR 0x044
|
|
#define GSWIP_BM_RAM_CTRL 0x045
|
|
#define GSWIP_BM_RAM_CTRL_BAS BIT(15)
|
|
#define GSWIP_BM_RAM_CTRL_OPMOD BIT(5)
|
|
#define GSWIP_BM_RAM_CTRL_ADDR_MASK GENMASK(4, 0)
|
|
#define GSWIP_BM_QUEUE_GCTRL 0x04A
|
|
#define GSWIP_BM_QUEUE_GCTRL_GL_MOD BIT(10)
|
|
/* buffer management Port Configuration Register */
|
|
#define GSWIP_BM_PCFGp(p) (0x080 + ((p) * 2))
|
|
#define GSWIP_BM_PCFG_CNTEN BIT(0) /* RMON Counter Enable */
|
|
#define GSWIP_BM_PCFG_IGCNT BIT(1) /* Ingres Special Tag RMON count */
|
|
/* buffer management Port Control Register */
|
|
#define GSWIP_BM_RMON_CTRLp(p) (0x81 + ((p) * 2))
|
|
#define GSWIP_BM_CTRL_RMON_RAM1_RES BIT(0) /* Software Reset for RMON RAM 1 */
|
|
#define GSWIP_BM_CTRL_RMON_RAM2_RES BIT(1) /* Software Reset for RMON RAM 2 */
|
|
|
|
/* PCE */
|
|
#define GSWIP_PCE_TBL_KEY(x) (0x447 - (x))
|
|
#define GSWIP_PCE_TBL_MASK 0x448
|
|
#define GSWIP_PCE_TBL_VAL(x) (0x44D - (x))
|
|
#define GSWIP_PCE_TBL_ADDR 0x44E
|
|
#define GSWIP_PCE_TBL_CTRL 0x44F
|
|
#define GSWIP_PCE_TBL_CTRL_BAS BIT(15)
|
|
#define GSWIP_PCE_TBL_CTRL_TYPE BIT(13)
|
|
#define GSWIP_PCE_TBL_CTRL_VLD BIT(12)
|
|
#define GSWIP_PCE_TBL_CTRL_KEYFORM BIT(11)
|
|
#define GSWIP_PCE_TBL_CTRL_GMAP_MASK GENMASK(10, 7)
|
|
#define GSWIP_PCE_TBL_CTRL_OPMOD_MASK GENMASK(6, 5)
|
|
#define GSWIP_PCE_TBL_CTRL_OPMOD_ADRD 0x00
|
|
#define GSWIP_PCE_TBL_CTRL_OPMOD_ADWR 0x20
|
|
#define GSWIP_PCE_TBL_CTRL_OPMOD_KSRD 0x40
|
|
#define GSWIP_PCE_TBL_CTRL_OPMOD_KSWR 0x60
|
|
#define GSWIP_PCE_TBL_CTRL_ADDR_MASK GENMASK(4, 0)
|
|
#define GSWIP_PCE_PMAP1 0x453 /* Monitoring port map */
|
|
#define GSWIP_PCE_PMAP2 0x454 /* Default Multicast port map */
|
|
#define GSWIP_PCE_PMAP3 0x455 /* Default Unknown Unicast port map */
|
|
#define GSWIP_PCE_GCTRL_0 0x456
|
|
#define GSWIP_PCE_GCTRL_0_MTFL BIT(0) /* MAC Table Flushing */
|
|
#define GSWIP_PCE_GCTRL_0_MC_VALID BIT(3)
|
|
#define GSWIP_PCE_GCTRL_0_VLAN BIT(14) /* VLAN aware Switching */
|
|
#define GSWIP_PCE_GCTRL_1 0x457
|
|
#define GSWIP_PCE_GCTRL_1_MAC_GLOCK BIT(2) /* MAC Address table lock */
|
|
#define GSWIP_PCE_GCTRL_1_MAC_GLOCK_MOD BIT(3) /* Mac address table lock forwarding mode */
|
|
#define GSWIP_PCE_PCTRL_0p(p) (0x480 + ((p) * 0xA))
|
|
#define GSWIP_PCE_PCTRL_0_TVM BIT(5) /* Transparent VLAN mode */
|
|
#define GSWIP_PCE_PCTRL_0_VREP BIT(6) /* VLAN Replace Mode */
|
|
#define GSWIP_PCE_PCTRL_0_INGRESS BIT(11) /* Accept special tag in ingress */
|
|
#define GSWIP_PCE_PCTRL_0_PSTATE_LISTEN 0x0
|
|
#define GSWIP_PCE_PCTRL_0_PSTATE_RX 0x1
|
|
#define GSWIP_PCE_PCTRL_0_PSTATE_TX 0x2
|
|
#define GSWIP_PCE_PCTRL_0_PSTATE_LEARNING 0x3
|
|
#define GSWIP_PCE_PCTRL_0_PSTATE_FORWARDING 0x7
|
|
#define GSWIP_PCE_PCTRL_0_PSTATE_MASK GENMASK(2, 0)
|
|
#define GSWIP_PCE_VCTRL(p) (0x485 + ((p) * 0xA))
|
|
#define GSWIP_PCE_VCTRL_UVR BIT(0) /* Unknown VLAN Rule */
|
|
#define GSWIP_PCE_VCTRL_VIMR BIT(3) /* VLAN Ingress Member violation rule */
|
|
#define GSWIP_PCE_VCTRL_VEMR BIT(4) /* VLAN Egress Member violation rule */
|
|
#define GSWIP_PCE_VCTRL_VSR BIT(5) /* VLAN Security */
|
|
#define GSWIP_PCE_VCTRL_VID0 BIT(6) /* Priority Tagged Rule */
|
|
#define GSWIP_PCE_DEFPVID(p) (0x486 + ((p) * 0xA))
|
|
|
|
#define GSWIP_MAC_FLEN 0x8C5
|
|
#define GSWIP_MAC_CTRL_2p(p) (0x905 + ((p) * 0xC))
|
|
#define GSWIP_MAC_CTRL_2_MLEN BIT(3) /* Maximum Untagged Frame Lnegth */
|
|
|
|
/* Ethernet Switch Fetch DMA Port Control Register */
|
|
#define GSWIP_FDMA_PCTRLp(p) (0xA80 + ((p) * 0x6))
|
|
#define GSWIP_FDMA_PCTRL_EN BIT(0) /* FDMA Port Enable */
|
|
#define GSWIP_FDMA_PCTRL_STEN BIT(1) /* Special Tag Insertion Enable */
|
|
#define GSWIP_FDMA_PCTRL_VLANMOD_MASK GENMASK(4, 3) /* VLAN Modification Control */
|
|
#define GSWIP_FDMA_PCTRL_VLANMOD_SHIFT 3 /* VLAN Modification Control */
|
|
#define GSWIP_FDMA_PCTRL_VLANMOD_DIS (0x0 << GSWIP_FDMA_PCTRL_VLANMOD_SHIFT)
|
|
#define GSWIP_FDMA_PCTRL_VLANMOD_PRIO (0x1 << GSWIP_FDMA_PCTRL_VLANMOD_SHIFT)
|
|
#define GSWIP_FDMA_PCTRL_VLANMOD_ID (0x2 << GSWIP_FDMA_PCTRL_VLANMOD_SHIFT)
|
|
#define GSWIP_FDMA_PCTRL_VLANMOD_BOTH (0x3 << GSWIP_FDMA_PCTRL_VLANMOD_SHIFT)
|
|
|
|
/* Ethernet Switch Store DMA Port Control Register */
|
|
#define GSWIP_SDMA_PCTRLp(p) (0xBC0 + ((p) * 0x6))
|
|
#define GSWIP_SDMA_PCTRL_EN BIT(0) /* SDMA Port Enable */
|
|
#define GSWIP_SDMA_PCTRL_FCEN BIT(1) /* Flow Control Enable */
|
|
#define GSWIP_SDMA_PCTRL_PAUFWD BIT(1) /* Pause Frame Forwarding */
|
|
|
|
#define GSWIP_TABLE_ACTIVE_VLAN 0x01
|
|
#define GSWIP_TABLE_VLAN_MAPPING 0x02
|
|
#define GSWIP_TABLE_MAC_BRIDGE 0x0b
|
|
#define GSWIP_TABLE_MAC_BRIDGE_STATIC 0x01 /* Static not, aging entry */
|
|
|
|
#define XRX200_GPHY_FW_ALIGN (16 * 1024)
|
|
|
|
struct gswip_hw_info {
|
|
int max_ports;
|
|
int cpu_port;
|
|
};
|
|
|
|
struct xway_gphy_match_data {
|
|
char *fe_firmware_name;
|
|
char *ge_firmware_name;
|
|
};
|
|
|
|
struct gswip_gphy_fw {
|
|
struct clk *clk_gate;
|
|
struct reset_control *reset;
|
|
u32 fw_addr_offset;
|
|
char *fw_name;
|
|
};
|
|
|
|
struct gswip_vlan {
|
|
struct net_device *bridge;
|
|
u16 vid;
|
|
u8 fid;
|
|
};
|
|
|
|
struct gswip_priv {
|
|
__iomem void *gswip;
|
|
__iomem void *mdio;
|
|
__iomem void *mii;
|
|
const struct gswip_hw_info *hw_info;
|
|
const struct xway_gphy_match_data *gphy_fw_name_cfg;
|
|
struct dsa_switch *ds;
|
|
struct device *dev;
|
|
struct regmap *rcu_regmap;
|
|
struct gswip_vlan vlans[64];
|
|
int num_gphy_fw;
|
|
struct gswip_gphy_fw *gphy_fw;
|
|
u32 port_vlan_filter;
|
|
};
|
|
|
|
struct gswip_pce_table_entry {
|
|
u16 index; // PCE_TBL_ADDR.ADDR = pData->table_index
|
|
u16 table; // PCE_TBL_CTRL.ADDR = pData->table
|
|
u16 key[8];
|
|
u16 val[5];
|
|
u16 mask;
|
|
u8 gmap;
|
|
bool type;
|
|
bool valid;
|
|
bool key_mode;
|
|
};
|
|
|
|
struct gswip_rmon_cnt_desc {
|
|
unsigned int size;
|
|
unsigned int offset;
|
|
const char *name;
|
|
};
|
|
|
|
#define MIB_DESC(_size, _offset, _name) {.size = _size, .offset = _offset, .name = _name}
|
|
|
|
static const struct gswip_rmon_cnt_desc gswip_rmon_cnt[] = {
|
|
/** Receive Packet Count (only packets that are accepted and not discarded). */
|
|
MIB_DESC(1, 0x1F, "RxGoodPkts"),
|
|
MIB_DESC(1, 0x23, "RxUnicastPkts"),
|
|
MIB_DESC(1, 0x22, "RxMulticastPkts"),
|
|
MIB_DESC(1, 0x21, "RxFCSErrorPkts"),
|
|
MIB_DESC(1, 0x1D, "RxUnderSizeGoodPkts"),
|
|
MIB_DESC(1, 0x1E, "RxUnderSizeErrorPkts"),
|
|
MIB_DESC(1, 0x1B, "RxOversizeGoodPkts"),
|
|
MIB_DESC(1, 0x1C, "RxOversizeErrorPkts"),
|
|
MIB_DESC(1, 0x20, "RxGoodPausePkts"),
|
|
MIB_DESC(1, 0x1A, "RxAlignErrorPkts"),
|
|
MIB_DESC(1, 0x12, "Rx64BytePkts"),
|
|
MIB_DESC(1, 0x13, "Rx127BytePkts"),
|
|
MIB_DESC(1, 0x14, "Rx255BytePkts"),
|
|
MIB_DESC(1, 0x15, "Rx511BytePkts"),
|
|
MIB_DESC(1, 0x16, "Rx1023BytePkts"),
|
|
/** Receive Size 1024-1522 (or more, if configured) Packet Count. */
|
|
MIB_DESC(1, 0x17, "RxMaxBytePkts"),
|
|
MIB_DESC(1, 0x18, "RxDroppedPkts"),
|
|
MIB_DESC(1, 0x19, "RxFilteredPkts"),
|
|
MIB_DESC(2, 0x24, "RxGoodBytes"),
|
|
MIB_DESC(2, 0x26, "RxBadBytes"),
|
|
MIB_DESC(1, 0x11, "TxAcmDroppedPkts"),
|
|
MIB_DESC(1, 0x0C, "TxGoodPkts"),
|
|
MIB_DESC(1, 0x06, "TxUnicastPkts"),
|
|
MIB_DESC(1, 0x07, "TxMulticastPkts"),
|
|
MIB_DESC(1, 0x00, "Tx64BytePkts"),
|
|
MIB_DESC(1, 0x01, "Tx127BytePkts"),
|
|
MIB_DESC(1, 0x02, "Tx255BytePkts"),
|
|
MIB_DESC(1, 0x03, "Tx511BytePkts"),
|
|
MIB_DESC(1, 0x04, "Tx1023BytePkts"),
|
|
/** Transmit Size 1024-1522 (or more, if configured) Packet Count. */
|
|
MIB_DESC(1, 0x05, "TxMaxBytePkts"),
|
|
MIB_DESC(1, 0x08, "TxSingleCollCount"),
|
|
MIB_DESC(1, 0x09, "TxMultCollCount"),
|
|
MIB_DESC(1, 0x0A, "TxLateCollCount"),
|
|
MIB_DESC(1, 0x0B, "TxExcessCollCount"),
|
|
MIB_DESC(1, 0x0D, "TxPauseCount"),
|
|
MIB_DESC(1, 0x10, "TxDroppedPkts"),
|
|
MIB_DESC(2, 0x0E, "TxGoodBytes"),
|
|
};
|
|
|
|
static u32 gswip_switch_r(struct gswip_priv *priv, u32 offset)
|
|
{
|
|
return __raw_readl(priv->gswip + (offset * 4));
|
|
}
|
|
|
|
static void gswip_switch_w(struct gswip_priv *priv, u32 val, u32 offset)
|
|
{
|
|
__raw_writel(val, priv->gswip + (offset * 4));
|
|
}
|
|
|
|
static void gswip_switch_mask(struct gswip_priv *priv, u32 clear, u32 set,
|
|
u32 offset)
|
|
{
|
|
u32 val = gswip_switch_r(priv, offset);
|
|
|
|
val &= ~(clear);
|
|
val |= set;
|
|
gswip_switch_w(priv, val, offset);
|
|
}
|
|
|
|
static u32 gswip_switch_r_timeout(struct gswip_priv *priv, u32 offset,
|
|
u32 cleared)
|
|
{
|
|
u32 val;
|
|
|
|
return readx_poll_timeout(__raw_readl, priv->gswip + (offset * 4), val,
|
|
(val & cleared) == 0, 20, 50000);
|
|
}
|
|
|
|
static u32 gswip_mdio_r(struct gswip_priv *priv, u32 offset)
|
|
{
|
|
return __raw_readl(priv->mdio + (offset * 4));
|
|
}
|
|
|
|
static void gswip_mdio_w(struct gswip_priv *priv, u32 val, u32 offset)
|
|
{
|
|
__raw_writel(val, priv->mdio + (offset * 4));
|
|
}
|
|
|
|
static void gswip_mdio_mask(struct gswip_priv *priv, u32 clear, u32 set,
|
|
u32 offset)
|
|
{
|
|
u32 val = gswip_mdio_r(priv, offset);
|
|
|
|
val &= ~(clear);
|
|
val |= set;
|
|
gswip_mdio_w(priv, val, offset);
|
|
}
|
|
|
|
static u32 gswip_mii_r(struct gswip_priv *priv, u32 offset)
|
|
{
|
|
return __raw_readl(priv->mii + (offset * 4));
|
|
}
|
|
|
|
static void gswip_mii_w(struct gswip_priv *priv, u32 val, u32 offset)
|
|
{
|
|
__raw_writel(val, priv->mii + (offset * 4));
|
|
}
|
|
|
|
static void gswip_mii_mask(struct gswip_priv *priv, u32 clear, u32 set,
|
|
u32 offset)
|
|
{
|
|
u32 val = gswip_mii_r(priv, offset);
|
|
|
|
val &= ~(clear);
|
|
val |= set;
|
|
gswip_mii_w(priv, val, offset);
|
|
}
|
|
|
|
static void gswip_mii_mask_cfg(struct gswip_priv *priv, u32 clear, u32 set,
|
|
int port)
|
|
{
|
|
switch (port) {
|
|
case 0:
|
|
gswip_mii_mask(priv, clear, set, GSWIP_MII_CFG0);
|
|
break;
|
|
case 1:
|
|
gswip_mii_mask(priv, clear, set, GSWIP_MII_CFG1);
|
|
break;
|
|
case 5:
|
|
gswip_mii_mask(priv, clear, set, GSWIP_MII_CFG5);
|
|
break;
|
|
}
|
|
}
|
|
|
|
static void gswip_mii_mask_pcdu(struct gswip_priv *priv, u32 clear, u32 set,
|
|
int port)
|
|
{
|
|
switch (port) {
|
|
case 0:
|
|
gswip_mii_mask(priv, clear, set, GSWIP_MII_PCDU0);
|
|
break;
|
|
case 1:
|
|
gswip_mii_mask(priv, clear, set, GSWIP_MII_PCDU1);
|
|
break;
|
|
case 5:
|
|
gswip_mii_mask(priv, clear, set, GSWIP_MII_PCDU5);
|
|
break;
|
|
}
|
|
}
|
|
|
|
static int gswip_mdio_poll(struct gswip_priv *priv)
|
|
{
|
|
int cnt = 100;
|
|
|
|
while (likely(cnt--)) {
|
|
u32 ctrl = gswip_mdio_r(priv, GSWIP_MDIO_CTRL);
|
|
|
|
if ((ctrl & GSWIP_MDIO_CTRL_BUSY) == 0)
|
|
return 0;
|
|
usleep_range(20, 40);
|
|
}
|
|
|
|
return -ETIMEDOUT;
|
|
}
|
|
|
|
static int gswip_mdio_wr(struct mii_bus *bus, int addr, int reg, u16 val)
|
|
{
|
|
struct gswip_priv *priv = bus->priv;
|
|
int err;
|
|
|
|
err = gswip_mdio_poll(priv);
|
|
if (err) {
|
|
dev_err(&bus->dev, "waiting for MDIO bus busy timed out\n");
|
|
return err;
|
|
}
|
|
|
|
gswip_mdio_w(priv, val, GSWIP_MDIO_WRITE);
|
|
gswip_mdio_w(priv, GSWIP_MDIO_CTRL_BUSY | GSWIP_MDIO_CTRL_WR |
|
|
((addr & GSWIP_MDIO_CTRL_PHYAD_MASK) << GSWIP_MDIO_CTRL_PHYAD_SHIFT) |
|
|
(reg & GSWIP_MDIO_CTRL_REGAD_MASK),
|
|
GSWIP_MDIO_CTRL);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int gswip_mdio_rd(struct mii_bus *bus, int addr, int reg)
|
|
{
|
|
struct gswip_priv *priv = bus->priv;
|
|
int err;
|
|
|
|
err = gswip_mdio_poll(priv);
|
|
if (err) {
|
|
dev_err(&bus->dev, "waiting for MDIO bus busy timed out\n");
|
|
return err;
|
|
}
|
|
|
|
gswip_mdio_w(priv, GSWIP_MDIO_CTRL_BUSY | GSWIP_MDIO_CTRL_RD |
|
|
((addr & GSWIP_MDIO_CTRL_PHYAD_MASK) << GSWIP_MDIO_CTRL_PHYAD_SHIFT) |
|
|
(reg & GSWIP_MDIO_CTRL_REGAD_MASK),
|
|
GSWIP_MDIO_CTRL);
|
|
|
|
err = gswip_mdio_poll(priv);
|
|
if (err) {
|
|
dev_err(&bus->dev, "waiting for MDIO bus busy timed out\n");
|
|
return err;
|
|
}
|
|
|
|
return gswip_mdio_r(priv, GSWIP_MDIO_READ);
|
|
}
|
|
|
|
static int gswip_mdio(struct gswip_priv *priv, struct device_node *mdio_np)
|
|
{
|
|
struct dsa_switch *ds = priv->ds;
|
|
|
|
ds->slave_mii_bus = devm_mdiobus_alloc(priv->dev);
|
|
if (!ds->slave_mii_bus)
|
|
return -ENOMEM;
|
|
|
|
ds->slave_mii_bus->priv = priv;
|
|
ds->slave_mii_bus->read = gswip_mdio_rd;
|
|
ds->slave_mii_bus->write = gswip_mdio_wr;
|
|
ds->slave_mii_bus->name = "lantiq,xrx200-mdio";
|
|
snprintf(ds->slave_mii_bus->id, MII_BUS_ID_SIZE, "%s-mii",
|
|
dev_name(priv->dev));
|
|
ds->slave_mii_bus->parent = priv->dev;
|
|
ds->slave_mii_bus->phy_mask = ~ds->phys_mii_mask;
|
|
|
|
return of_mdiobus_register(ds->slave_mii_bus, mdio_np);
|
|
}
|
|
|
|
static int gswip_pce_table_entry_read(struct gswip_priv *priv,
|
|
struct gswip_pce_table_entry *tbl)
|
|
{
|
|
int i;
|
|
int err;
|
|
u16 crtl;
|
|
u16 addr_mode = tbl->key_mode ? GSWIP_PCE_TBL_CTRL_OPMOD_KSRD :
|
|
GSWIP_PCE_TBL_CTRL_OPMOD_ADRD;
|
|
|
|
err = gswip_switch_r_timeout(priv, GSWIP_PCE_TBL_CTRL,
|
|
GSWIP_PCE_TBL_CTRL_BAS);
|
|
if (err)
|
|
return err;
|
|
|
|
gswip_switch_w(priv, tbl->index, GSWIP_PCE_TBL_ADDR);
|
|
gswip_switch_mask(priv, GSWIP_PCE_TBL_CTRL_ADDR_MASK |
|
|
GSWIP_PCE_TBL_CTRL_OPMOD_MASK,
|
|
tbl->table | addr_mode | GSWIP_PCE_TBL_CTRL_BAS,
|
|
GSWIP_PCE_TBL_CTRL);
|
|
|
|
err = gswip_switch_r_timeout(priv, GSWIP_PCE_TBL_CTRL,
|
|
GSWIP_PCE_TBL_CTRL_BAS);
|
|
if (err)
|
|
return err;
|
|
|
|
for (i = 0; i < ARRAY_SIZE(tbl->key); i++)
|
|
tbl->key[i] = gswip_switch_r(priv, GSWIP_PCE_TBL_KEY(i));
|
|
|
|
for (i = 0; i < ARRAY_SIZE(tbl->val); i++)
|
|
tbl->val[i] = gswip_switch_r(priv, GSWIP_PCE_TBL_VAL(i));
|
|
|
|
tbl->mask = gswip_switch_r(priv, GSWIP_PCE_TBL_MASK);
|
|
|
|
crtl = gswip_switch_r(priv, GSWIP_PCE_TBL_CTRL);
|
|
|
|
tbl->type = !!(crtl & GSWIP_PCE_TBL_CTRL_TYPE);
|
|
tbl->valid = !!(crtl & GSWIP_PCE_TBL_CTRL_VLD);
|
|
tbl->gmap = (crtl & GSWIP_PCE_TBL_CTRL_GMAP_MASK) >> 7;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int gswip_pce_table_entry_write(struct gswip_priv *priv,
|
|
struct gswip_pce_table_entry *tbl)
|
|
{
|
|
int i;
|
|
int err;
|
|
u16 crtl;
|
|
u16 addr_mode = tbl->key_mode ? GSWIP_PCE_TBL_CTRL_OPMOD_KSWR :
|
|
GSWIP_PCE_TBL_CTRL_OPMOD_ADWR;
|
|
|
|
err = gswip_switch_r_timeout(priv, GSWIP_PCE_TBL_CTRL,
|
|
GSWIP_PCE_TBL_CTRL_BAS);
|
|
if (err)
|
|
return err;
|
|
|
|
gswip_switch_w(priv, tbl->index, GSWIP_PCE_TBL_ADDR);
|
|
gswip_switch_mask(priv, GSWIP_PCE_TBL_CTRL_ADDR_MASK |
|
|
GSWIP_PCE_TBL_CTRL_OPMOD_MASK,
|
|
tbl->table | addr_mode,
|
|
GSWIP_PCE_TBL_CTRL);
|
|
|
|
for (i = 0; i < ARRAY_SIZE(tbl->key); i++)
|
|
gswip_switch_w(priv, tbl->key[i], GSWIP_PCE_TBL_KEY(i));
|
|
|
|
for (i = 0; i < ARRAY_SIZE(tbl->val); i++)
|
|
gswip_switch_w(priv, tbl->val[i], GSWIP_PCE_TBL_VAL(i));
|
|
|
|
gswip_switch_mask(priv, GSWIP_PCE_TBL_CTRL_ADDR_MASK |
|
|
GSWIP_PCE_TBL_CTRL_OPMOD_MASK,
|
|
tbl->table | addr_mode,
|
|
GSWIP_PCE_TBL_CTRL);
|
|
|
|
gswip_switch_w(priv, tbl->mask, GSWIP_PCE_TBL_MASK);
|
|
|
|
crtl = gswip_switch_r(priv, GSWIP_PCE_TBL_CTRL);
|
|
crtl &= ~(GSWIP_PCE_TBL_CTRL_TYPE | GSWIP_PCE_TBL_CTRL_VLD |
|
|
GSWIP_PCE_TBL_CTRL_GMAP_MASK);
|
|
if (tbl->type)
|
|
crtl |= GSWIP_PCE_TBL_CTRL_TYPE;
|
|
if (tbl->valid)
|
|
crtl |= GSWIP_PCE_TBL_CTRL_VLD;
|
|
crtl |= (tbl->gmap << 7) & GSWIP_PCE_TBL_CTRL_GMAP_MASK;
|
|
crtl |= GSWIP_PCE_TBL_CTRL_BAS;
|
|
gswip_switch_w(priv, crtl, GSWIP_PCE_TBL_CTRL);
|
|
|
|
return gswip_switch_r_timeout(priv, GSWIP_PCE_TBL_CTRL,
|
|
GSWIP_PCE_TBL_CTRL_BAS);
|
|
}
|
|
|
|
/* Add the LAN port into a bridge with the CPU port by
|
|
* default. This prevents automatic forwarding of
|
|
* packages between the LAN ports when no explicit
|
|
* bridge is configured.
|
|
*/
|
|
static int gswip_add_single_port_br(struct gswip_priv *priv, int port, bool add)
|
|
{
|
|
struct gswip_pce_table_entry vlan_active = {0,};
|
|
struct gswip_pce_table_entry vlan_mapping = {0,};
|
|
unsigned int cpu_port = priv->hw_info->cpu_port;
|
|
unsigned int max_ports = priv->hw_info->max_ports;
|
|
int err;
|
|
|
|
if (port >= max_ports) {
|
|
dev_err(priv->dev, "single port for %i supported\n", port);
|
|
return -EIO;
|
|
}
|
|
|
|
vlan_active.index = port + 1;
|
|
vlan_active.table = GSWIP_TABLE_ACTIVE_VLAN;
|
|
vlan_active.key[0] = 0; /* vid */
|
|
vlan_active.val[0] = port + 1 /* fid */;
|
|
vlan_active.valid = add;
|
|
err = gswip_pce_table_entry_write(priv, &vlan_active);
|
|
if (err) {
|
|
dev_err(priv->dev, "failed to write active VLAN: %d\n", err);
|
|
return err;
|
|
}
|
|
|
|
if (!add)
|
|
return 0;
|
|
|
|
vlan_mapping.index = port + 1;
|
|
vlan_mapping.table = GSWIP_TABLE_VLAN_MAPPING;
|
|
vlan_mapping.val[0] = 0 /* vid */;
|
|
vlan_mapping.val[1] = BIT(port) | BIT(cpu_port);
|
|
vlan_mapping.val[2] = 0;
|
|
err = gswip_pce_table_entry_write(priv, &vlan_mapping);
|
|
if (err) {
|
|
dev_err(priv->dev, "failed to write VLAN mapping: %d\n", err);
|
|
return err;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int gswip_port_enable(struct dsa_switch *ds, int port,
|
|
struct phy_device *phydev)
|
|
{
|
|
struct gswip_priv *priv = ds->priv;
|
|
int err;
|
|
|
|
if (!dsa_is_user_port(ds, port))
|
|
return 0;
|
|
|
|
if (!dsa_is_cpu_port(ds, port)) {
|
|
err = gswip_add_single_port_br(priv, port, true);
|
|
if (err)
|
|
return err;
|
|
}
|
|
|
|
/* RMON Counter Enable for port */
|
|
gswip_switch_w(priv, GSWIP_BM_PCFG_CNTEN, GSWIP_BM_PCFGp(port));
|
|
|
|
/* enable port fetch/store dma & VLAN Modification */
|
|
gswip_switch_mask(priv, 0, GSWIP_FDMA_PCTRL_EN |
|
|
GSWIP_FDMA_PCTRL_VLANMOD_BOTH,
|
|
GSWIP_FDMA_PCTRLp(port));
|
|
gswip_switch_mask(priv, 0, GSWIP_SDMA_PCTRL_EN,
|
|
GSWIP_SDMA_PCTRLp(port));
|
|
|
|
if (!dsa_is_cpu_port(ds, port)) {
|
|
u32 macconf = GSWIP_MDIO_PHY_LINK_AUTO |
|
|
GSWIP_MDIO_PHY_SPEED_AUTO |
|
|
GSWIP_MDIO_PHY_FDUP_AUTO |
|
|
GSWIP_MDIO_PHY_FCONTX_AUTO |
|
|
GSWIP_MDIO_PHY_FCONRX_AUTO |
|
|
(phydev->mdio.addr & GSWIP_MDIO_PHY_ADDR_MASK);
|
|
|
|
gswip_mdio_w(priv, macconf, GSWIP_MDIO_PHYp(port));
|
|
/* Activate MDIO auto polling */
|
|
gswip_mdio_mask(priv, 0, BIT(port), GSWIP_MDIO_MDC_CFG0);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void gswip_port_disable(struct dsa_switch *ds, int port)
|
|
{
|
|
struct gswip_priv *priv = ds->priv;
|
|
|
|
if (!dsa_is_user_port(ds, port))
|
|
return;
|
|
|
|
if (!dsa_is_cpu_port(ds, port)) {
|
|
gswip_mdio_mask(priv, GSWIP_MDIO_PHY_LINK_DOWN,
|
|
GSWIP_MDIO_PHY_LINK_MASK,
|
|
GSWIP_MDIO_PHYp(port));
|
|
/* Deactivate MDIO auto polling */
|
|
gswip_mdio_mask(priv, BIT(port), 0, GSWIP_MDIO_MDC_CFG0);
|
|
}
|
|
|
|
gswip_switch_mask(priv, GSWIP_FDMA_PCTRL_EN, 0,
|
|
GSWIP_FDMA_PCTRLp(port));
|
|
gswip_switch_mask(priv, GSWIP_SDMA_PCTRL_EN, 0,
|
|
GSWIP_SDMA_PCTRLp(port));
|
|
}
|
|
|
|
static int gswip_pce_load_microcode(struct gswip_priv *priv)
|
|
{
|
|
int i;
|
|
int err;
|
|
|
|
gswip_switch_mask(priv, GSWIP_PCE_TBL_CTRL_ADDR_MASK |
|
|
GSWIP_PCE_TBL_CTRL_OPMOD_MASK,
|
|
GSWIP_PCE_TBL_CTRL_OPMOD_ADWR, GSWIP_PCE_TBL_CTRL);
|
|
gswip_switch_w(priv, 0, GSWIP_PCE_TBL_MASK);
|
|
|
|
for (i = 0; i < ARRAY_SIZE(gswip_pce_microcode); i++) {
|
|
gswip_switch_w(priv, i, GSWIP_PCE_TBL_ADDR);
|
|
gswip_switch_w(priv, gswip_pce_microcode[i].val_0,
|
|
GSWIP_PCE_TBL_VAL(0));
|
|
gswip_switch_w(priv, gswip_pce_microcode[i].val_1,
|
|
GSWIP_PCE_TBL_VAL(1));
|
|
gswip_switch_w(priv, gswip_pce_microcode[i].val_2,
|
|
GSWIP_PCE_TBL_VAL(2));
|
|
gswip_switch_w(priv, gswip_pce_microcode[i].val_3,
|
|
GSWIP_PCE_TBL_VAL(3));
|
|
|
|
/* start the table access: */
|
|
gswip_switch_mask(priv, 0, GSWIP_PCE_TBL_CTRL_BAS,
|
|
GSWIP_PCE_TBL_CTRL);
|
|
err = gswip_switch_r_timeout(priv, GSWIP_PCE_TBL_CTRL,
|
|
GSWIP_PCE_TBL_CTRL_BAS);
|
|
if (err)
|
|
return err;
|
|
}
|
|
|
|
/* tell the switch that the microcode is loaded */
|
|
gswip_switch_mask(priv, 0, GSWIP_PCE_GCTRL_0_MC_VALID,
|
|
GSWIP_PCE_GCTRL_0);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int gswip_port_vlan_filtering(struct dsa_switch *ds, int port,
|
|
bool vlan_filtering,
|
|
struct switchdev_trans *trans)
|
|
{
|
|
struct gswip_priv *priv = ds->priv;
|
|
|
|
/* Do not allow changing the VLAN filtering options while in bridge */
|
|
if (switchdev_trans_ph_prepare(trans)) {
|
|
struct net_device *bridge = dsa_to_port(ds, port)->bridge_dev;
|
|
|
|
if (!bridge)
|
|
return 0;
|
|
|
|
if (!!(priv->port_vlan_filter & BIT(port)) != vlan_filtering)
|
|
return -EIO;
|
|
|
|
return 0;
|
|
}
|
|
|
|
if (vlan_filtering) {
|
|
/* Use port based VLAN tag */
|
|
gswip_switch_mask(priv,
|
|
GSWIP_PCE_VCTRL_VSR,
|
|
GSWIP_PCE_VCTRL_UVR | GSWIP_PCE_VCTRL_VIMR |
|
|
GSWIP_PCE_VCTRL_VEMR,
|
|
GSWIP_PCE_VCTRL(port));
|
|
gswip_switch_mask(priv, GSWIP_PCE_PCTRL_0_TVM, 0,
|
|
GSWIP_PCE_PCTRL_0p(port));
|
|
} else {
|
|
/* Use port based VLAN tag */
|
|
gswip_switch_mask(priv,
|
|
GSWIP_PCE_VCTRL_UVR | GSWIP_PCE_VCTRL_VIMR |
|
|
GSWIP_PCE_VCTRL_VEMR,
|
|
GSWIP_PCE_VCTRL_VSR,
|
|
GSWIP_PCE_VCTRL(port));
|
|
gswip_switch_mask(priv, 0, GSWIP_PCE_PCTRL_0_TVM,
|
|
GSWIP_PCE_PCTRL_0p(port));
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int gswip_setup(struct dsa_switch *ds)
|
|
{
|
|
struct gswip_priv *priv = ds->priv;
|
|
unsigned int cpu_port = priv->hw_info->cpu_port;
|
|
int i;
|
|
int err;
|
|
|
|
gswip_switch_w(priv, GSWIP_SWRES_R0, GSWIP_SWRES);
|
|
usleep_range(5000, 10000);
|
|
gswip_switch_w(priv, 0, GSWIP_SWRES);
|
|
|
|
/* disable port fetch/store dma on all ports */
|
|
for (i = 0; i < priv->hw_info->max_ports; i++) {
|
|
struct switchdev_trans trans;
|
|
|
|
/* Skip the prepare phase, this shouldn't return an error
|
|
* during setup.
|
|
*/
|
|
trans.ph_prepare = false;
|
|
|
|
gswip_port_disable(ds, i);
|
|
gswip_port_vlan_filtering(ds, i, false, &trans);
|
|
}
|
|
|
|
/* enable Switch */
|
|
gswip_mdio_mask(priv, 0, GSWIP_MDIO_GLOB_ENABLE, GSWIP_MDIO_GLOB);
|
|
|
|
err = gswip_pce_load_microcode(priv);
|
|
if (err) {
|
|
dev_err(priv->dev, "writing PCE microcode failed, %i", err);
|
|
return err;
|
|
}
|
|
|
|
/* Default unknown Broadcast/Multicast/Unicast port maps */
|
|
gswip_switch_w(priv, BIT(cpu_port), GSWIP_PCE_PMAP1);
|
|
gswip_switch_w(priv, BIT(cpu_port), GSWIP_PCE_PMAP2);
|
|
gswip_switch_w(priv, BIT(cpu_port), GSWIP_PCE_PMAP3);
|
|
|
|
/* disable PHY auto polling */
|
|
gswip_mdio_w(priv, 0x0, GSWIP_MDIO_MDC_CFG0);
|
|
/* Configure the MDIO Clock 2.5 MHz */
|
|
gswip_mdio_mask(priv, 0xff, 0x09, GSWIP_MDIO_MDC_CFG1);
|
|
|
|
/* Disable the xMII link */
|
|
gswip_mii_mask_cfg(priv, GSWIP_MII_CFG_EN, 0, 0);
|
|
gswip_mii_mask_cfg(priv, GSWIP_MII_CFG_EN, 0, 1);
|
|
gswip_mii_mask_cfg(priv, GSWIP_MII_CFG_EN, 0, 5);
|
|
|
|
/* enable special tag insertion on cpu port */
|
|
gswip_switch_mask(priv, 0, GSWIP_FDMA_PCTRL_STEN,
|
|
GSWIP_FDMA_PCTRLp(cpu_port));
|
|
|
|
/* accept special tag in ingress direction */
|
|
gswip_switch_mask(priv, 0, GSWIP_PCE_PCTRL_0_INGRESS,
|
|
GSWIP_PCE_PCTRL_0p(cpu_port));
|
|
|
|
gswip_switch_mask(priv, 0, GSWIP_MAC_CTRL_2_MLEN,
|
|
GSWIP_MAC_CTRL_2p(cpu_port));
|
|
gswip_switch_w(priv, VLAN_ETH_FRAME_LEN + 8, GSWIP_MAC_FLEN);
|
|
gswip_switch_mask(priv, 0, GSWIP_BM_QUEUE_GCTRL_GL_MOD,
|
|
GSWIP_BM_QUEUE_GCTRL);
|
|
|
|
/* VLAN aware Switching */
|
|
gswip_switch_mask(priv, 0, GSWIP_PCE_GCTRL_0_VLAN, GSWIP_PCE_GCTRL_0);
|
|
|
|
/* Flush MAC Table */
|
|
gswip_switch_mask(priv, 0, GSWIP_PCE_GCTRL_0_MTFL, GSWIP_PCE_GCTRL_0);
|
|
|
|
err = gswip_switch_r_timeout(priv, GSWIP_PCE_GCTRL_0,
|
|
GSWIP_PCE_GCTRL_0_MTFL);
|
|
if (err) {
|
|
dev_err(priv->dev, "MAC flushing didn't finish\n");
|
|
return err;
|
|
}
|
|
|
|
gswip_port_enable(ds, cpu_port, NULL);
|
|
return 0;
|
|
}
|
|
|
|
static enum dsa_tag_protocol gswip_get_tag_protocol(struct dsa_switch *ds,
|
|
int port,
|
|
enum dsa_tag_protocol mp)
|
|
{
|
|
return DSA_TAG_PROTO_GSWIP;
|
|
}
|
|
|
|
static int gswip_vlan_active_create(struct gswip_priv *priv,
|
|
struct net_device *bridge,
|
|
int fid, u16 vid)
|
|
{
|
|
struct gswip_pce_table_entry vlan_active = {0,};
|
|
unsigned int max_ports = priv->hw_info->max_ports;
|
|
int idx = -1;
|
|
int err;
|
|
int i;
|
|
|
|
/* Look for a free slot */
|
|
for (i = max_ports; i < ARRAY_SIZE(priv->vlans); i++) {
|
|
if (!priv->vlans[i].bridge) {
|
|
idx = i;
|
|
break;
|
|
}
|
|
}
|
|
|
|
if (idx == -1)
|
|
return -ENOSPC;
|
|
|
|
if (fid == -1)
|
|
fid = idx;
|
|
|
|
vlan_active.index = idx;
|
|
vlan_active.table = GSWIP_TABLE_ACTIVE_VLAN;
|
|
vlan_active.key[0] = vid;
|
|
vlan_active.val[0] = fid;
|
|
vlan_active.valid = true;
|
|
|
|
err = gswip_pce_table_entry_write(priv, &vlan_active);
|
|
if (err) {
|
|
dev_err(priv->dev, "failed to write active VLAN: %d\n", err);
|
|
return err;
|
|
}
|
|
|
|
priv->vlans[idx].bridge = bridge;
|
|
priv->vlans[idx].vid = vid;
|
|
priv->vlans[idx].fid = fid;
|
|
|
|
return idx;
|
|
}
|
|
|
|
static int gswip_vlan_active_remove(struct gswip_priv *priv, int idx)
|
|
{
|
|
struct gswip_pce_table_entry vlan_active = {0,};
|
|
int err;
|
|
|
|
vlan_active.index = idx;
|
|
vlan_active.table = GSWIP_TABLE_ACTIVE_VLAN;
|
|
vlan_active.valid = false;
|
|
err = gswip_pce_table_entry_write(priv, &vlan_active);
|
|
if (err)
|
|
dev_err(priv->dev, "failed to delete active VLAN: %d\n", err);
|
|
priv->vlans[idx].bridge = NULL;
|
|
|
|
return err;
|
|
}
|
|
|
|
static int gswip_vlan_add_unaware(struct gswip_priv *priv,
|
|
struct net_device *bridge, int port)
|
|
{
|
|
struct gswip_pce_table_entry vlan_mapping = {0,};
|
|
unsigned int max_ports = priv->hw_info->max_ports;
|
|
unsigned int cpu_port = priv->hw_info->cpu_port;
|
|
bool active_vlan_created = false;
|
|
int idx = -1;
|
|
int i;
|
|
int err;
|
|
|
|
/* Check if there is already a page for this bridge */
|
|
for (i = max_ports; i < ARRAY_SIZE(priv->vlans); i++) {
|
|
if (priv->vlans[i].bridge == bridge) {
|
|
idx = i;
|
|
break;
|
|
}
|
|
}
|
|
|
|
/* If this bridge is not programmed yet, add a Active VLAN table
|
|
* entry in a free slot and prepare the VLAN mapping table entry.
|
|
*/
|
|
if (idx == -1) {
|
|
idx = gswip_vlan_active_create(priv, bridge, -1, 0);
|
|
if (idx < 0)
|
|
return idx;
|
|
active_vlan_created = true;
|
|
|
|
vlan_mapping.index = idx;
|
|
vlan_mapping.table = GSWIP_TABLE_VLAN_MAPPING;
|
|
/* VLAN ID byte, maps to the VLAN ID of vlan active table */
|
|
vlan_mapping.val[0] = 0;
|
|
} else {
|
|
/* Read the existing VLAN mapping entry from the switch */
|
|
vlan_mapping.index = idx;
|
|
vlan_mapping.table = GSWIP_TABLE_VLAN_MAPPING;
|
|
err = gswip_pce_table_entry_read(priv, &vlan_mapping);
|
|
if (err) {
|
|
dev_err(priv->dev, "failed to read VLAN mapping: %d\n",
|
|
err);
|
|
return err;
|
|
}
|
|
}
|
|
|
|
/* Update the VLAN mapping entry and write it to the switch */
|
|
vlan_mapping.val[1] |= BIT(cpu_port);
|
|
vlan_mapping.val[1] |= BIT(port);
|
|
err = gswip_pce_table_entry_write(priv, &vlan_mapping);
|
|
if (err) {
|
|
dev_err(priv->dev, "failed to write VLAN mapping: %d\n", err);
|
|
/* In case an Active VLAN was creaetd delete it again */
|
|
if (active_vlan_created)
|
|
gswip_vlan_active_remove(priv, idx);
|
|
return err;
|
|
}
|
|
|
|
gswip_switch_w(priv, 0, GSWIP_PCE_DEFPVID(port));
|
|
return 0;
|
|
}
|
|
|
|
static int gswip_vlan_add_aware(struct gswip_priv *priv,
|
|
struct net_device *bridge, int port,
|
|
u16 vid, bool untagged,
|
|
bool pvid)
|
|
{
|
|
struct gswip_pce_table_entry vlan_mapping = {0,};
|
|
unsigned int max_ports = priv->hw_info->max_ports;
|
|
unsigned int cpu_port = priv->hw_info->cpu_port;
|
|
bool active_vlan_created = false;
|
|
int idx = -1;
|
|
int fid = -1;
|
|
int i;
|
|
int err;
|
|
|
|
/* Check if there is already a page for this bridge */
|
|
for (i = max_ports; i < ARRAY_SIZE(priv->vlans); i++) {
|
|
if (priv->vlans[i].bridge == bridge) {
|
|
if (fid != -1 && fid != priv->vlans[i].fid)
|
|
dev_err(priv->dev, "one bridge with multiple flow ids\n");
|
|
fid = priv->vlans[i].fid;
|
|
if (priv->vlans[i].vid == vid) {
|
|
idx = i;
|
|
break;
|
|
}
|
|
}
|
|
}
|
|
|
|
/* If this bridge is not programmed yet, add a Active VLAN table
|
|
* entry in a free slot and prepare the VLAN mapping table entry.
|
|
*/
|
|
if (idx == -1) {
|
|
idx = gswip_vlan_active_create(priv, bridge, fid, vid);
|
|
if (idx < 0)
|
|
return idx;
|
|
active_vlan_created = true;
|
|
|
|
vlan_mapping.index = idx;
|
|
vlan_mapping.table = GSWIP_TABLE_VLAN_MAPPING;
|
|
/* VLAN ID byte, maps to the VLAN ID of vlan active table */
|
|
vlan_mapping.val[0] = vid;
|
|
} else {
|
|
/* Read the existing VLAN mapping entry from the switch */
|
|
vlan_mapping.index = idx;
|
|
vlan_mapping.table = GSWIP_TABLE_VLAN_MAPPING;
|
|
err = gswip_pce_table_entry_read(priv, &vlan_mapping);
|
|
if (err) {
|
|
dev_err(priv->dev, "failed to read VLAN mapping: %d\n",
|
|
err);
|
|
return err;
|
|
}
|
|
}
|
|
|
|
vlan_mapping.val[0] = vid;
|
|
/* Update the VLAN mapping entry and write it to the switch */
|
|
vlan_mapping.val[1] |= BIT(cpu_port);
|
|
vlan_mapping.val[2] |= BIT(cpu_port);
|
|
vlan_mapping.val[1] |= BIT(port);
|
|
if (untagged)
|
|
vlan_mapping.val[2] &= ~BIT(port);
|
|
else
|
|
vlan_mapping.val[2] |= BIT(port);
|
|
err = gswip_pce_table_entry_write(priv, &vlan_mapping);
|
|
if (err) {
|
|
dev_err(priv->dev, "failed to write VLAN mapping: %d\n", err);
|
|
/* In case an Active VLAN was creaetd delete it again */
|
|
if (active_vlan_created)
|
|
gswip_vlan_active_remove(priv, idx);
|
|
return err;
|
|
}
|
|
|
|
if (pvid)
|
|
gswip_switch_w(priv, idx, GSWIP_PCE_DEFPVID(port));
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int gswip_vlan_remove(struct gswip_priv *priv,
|
|
struct net_device *bridge, int port,
|
|
u16 vid, bool pvid, bool vlan_aware)
|
|
{
|
|
struct gswip_pce_table_entry vlan_mapping = {0,};
|
|
unsigned int max_ports = priv->hw_info->max_ports;
|
|
unsigned int cpu_port = priv->hw_info->cpu_port;
|
|
int idx = -1;
|
|
int i;
|
|
int err;
|
|
|
|
/* Check if there is already a page for this bridge */
|
|
for (i = max_ports; i < ARRAY_SIZE(priv->vlans); i++) {
|
|
if (priv->vlans[i].bridge == bridge &&
|
|
(!vlan_aware || priv->vlans[i].vid == vid)) {
|
|
idx = i;
|
|
break;
|
|
}
|
|
}
|
|
|
|
if (idx == -1) {
|
|
dev_err(priv->dev, "bridge to leave does not exists\n");
|
|
return -ENOENT;
|
|
}
|
|
|
|
vlan_mapping.index = idx;
|
|
vlan_mapping.table = GSWIP_TABLE_VLAN_MAPPING;
|
|
err = gswip_pce_table_entry_read(priv, &vlan_mapping);
|
|
if (err) {
|
|
dev_err(priv->dev, "failed to read VLAN mapping: %d\n", err);
|
|
return err;
|
|
}
|
|
|
|
vlan_mapping.val[1] &= ~BIT(port);
|
|
vlan_mapping.val[2] &= ~BIT(port);
|
|
err = gswip_pce_table_entry_write(priv, &vlan_mapping);
|
|
if (err) {
|
|
dev_err(priv->dev, "failed to write VLAN mapping: %d\n", err);
|
|
return err;
|
|
}
|
|
|
|
/* In case all ports are removed from the bridge, remove the VLAN */
|
|
if ((vlan_mapping.val[1] & ~BIT(cpu_port)) == 0) {
|
|
err = gswip_vlan_active_remove(priv, idx);
|
|
if (err) {
|
|
dev_err(priv->dev, "failed to write active VLAN: %d\n",
|
|
err);
|
|
return err;
|
|
}
|
|
}
|
|
|
|
/* GSWIP 2.2 (GRX300) and later program here the VID directly. */
|
|
if (pvid)
|
|
gswip_switch_w(priv, 0, GSWIP_PCE_DEFPVID(port));
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int gswip_port_bridge_join(struct dsa_switch *ds, int port,
|
|
struct net_device *bridge)
|
|
{
|
|
struct gswip_priv *priv = ds->priv;
|
|
int err;
|
|
|
|
/* When the bridge uses VLAN filtering we have to configure VLAN
|
|
* specific bridges. No bridge is configured here.
|
|
*/
|
|
if (!br_vlan_enabled(bridge)) {
|
|
err = gswip_vlan_add_unaware(priv, bridge, port);
|
|
if (err)
|
|
return err;
|
|
priv->port_vlan_filter &= ~BIT(port);
|
|
} else {
|
|
priv->port_vlan_filter |= BIT(port);
|
|
}
|
|
return gswip_add_single_port_br(priv, port, false);
|
|
}
|
|
|
|
static void gswip_port_bridge_leave(struct dsa_switch *ds, int port,
|
|
struct net_device *bridge)
|
|
{
|
|
struct gswip_priv *priv = ds->priv;
|
|
|
|
gswip_add_single_port_br(priv, port, true);
|
|
|
|
/* When the bridge uses VLAN filtering we have to configure VLAN
|
|
* specific bridges. No bridge is configured here.
|
|
*/
|
|
if (!br_vlan_enabled(bridge))
|
|
gswip_vlan_remove(priv, bridge, port, 0, true, false);
|
|
}
|
|
|
|
static int gswip_port_vlan_prepare(struct dsa_switch *ds, int port,
|
|
const struct switchdev_obj_port_vlan *vlan)
|
|
{
|
|
struct gswip_priv *priv = ds->priv;
|
|
struct net_device *bridge = dsa_to_port(ds, port)->bridge_dev;
|
|
unsigned int max_ports = priv->hw_info->max_ports;
|
|
u16 vid;
|
|
int i;
|
|
int pos = max_ports;
|
|
|
|
/* We only support VLAN filtering on bridges */
|
|
if (!dsa_is_cpu_port(ds, port) && !bridge)
|
|
return -EOPNOTSUPP;
|
|
|
|
for (vid = vlan->vid_begin; vid <= vlan->vid_end; ++vid) {
|
|
int idx = -1;
|
|
|
|
/* Check if there is already a page for this VLAN */
|
|
for (i = max_ports; i < ARRAY_SIZE(priv->vlans); i++) {
|
|
if (priv->vlans[i].bridge == bridge &&
|
|
priv->vlans[i].vid == vid) {
|
|
idx = i;
|
|
break;
|
|
}
|
|
}
|
|
|
|
/* If this VLAN is not programmed yet, we have to reserve
|
|
* one entry in the VLAN table. Make sure we start at the
|
|
* next position round.
|
|
*/
|
|
if (idx == -1) {
|
|
/* Look for a free slot */
|
|
for (; pos < ARRAY_SIZE(priv->vlans); pos++) {
|
|
if (!priv->vlans[pos].bridge) {
|
|
idx = pos;
|
|
pos++;
|
|
break;
|
|
}
|
|
}
|
|
|
|
if (idx == -1)
|
|
return -ENOSPC;
|
|
}
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void gswip_port_vlan_add(struct dsa_switch *ds, int port,
|
|
const struct switchdev_obj_port_vlan *vlan)
|
|
{
|
|
struct gswip_priv *priv = ds->priv;
|
|
struct net_device *bridge = dsa_to_port(ds, port)->bridge_dev;
|
|
bool untagged = vlan->flags & BRIDGE_VLAN_INFO_UNTAGGED;
|
|
bool pvid = vlan->flags & BRIDGE_VLAN_INFO_PVID;
|
|
u16 vid;
|
|
|
|
/* We have to receive all packets on the CPU port and should not
|
|
* do any VLAN filtering here. This is also called with bridge
|
|
* NULL and then we do not know for which bridge to configure
|
|
* this.
|
|
*/
|
|
if (dsa_is_cpu_port(ds, port))
|
|
return;
|
|
|
|
for (vid = vlan->vid_begin; vid <= vlan->vid_end; ++vid)
|
|
gswip_vlan_add_aware(priv, bridge, port, vid, untagged, pvid);
|
|
}
|
|
|
|
static int gswip_port_vlan_del(struct dsa_switch *ds, int port,
|
|
const struct switchdev_obj_port_vlan *vlan)
|
|
{
|
|
struct gswip_priv *priv = ds->priv;
|
|
struct net_device *bridge = dsa_to_port(ds, port)->bridge_dev;
|
|
bool pvid = vlan->flags & BRIDGE_VLAN_INFO_PVID;
|
|
u16 vid;
|
|
int err;
|
|
|
|
/* We have to receive all packets on the CPU port and should not
|
|
* do any VLAN filtering here. This is also called with bridge
|
|
* NULL and then we do not know for which bridge to configure
|
|
* this.
|
|
*/
|
|
if (dsa_is_cpu_port(ds, port))
|
|
return 0;
|
|
|
|
for (vid = vlan->vid_begin; vid <= vlan->vid_end; ++vid) {
|
|
err = gswip_vlan_remove(priv, bridge, port, vid, pvid, true);
|
|
if (err)
|
|
return err;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void gswip_port_fast_age(struct dsa_switch *ds, int port)
|
|
{
|
|
struct gswip_priv *priv = ds->priv;
|
|
struct gswip_pce_table_entry mac_bridge = {0,};
|
|
int i;
|
|
int err;
|
|
|
|
for (i = 0; i < 2048; i++) {
|
|
mac_bridge.table = GSWIP_TABLE_MAC_BRIDGE;
|
|
mac_bridge.index = i;
|
|
|
|
err = gswip_pce_table_entry_read(priv, &mac_bridge);
|
|
if (err) {
|
|
dev_err(priv->dev, "failed to read mac bridge: %d\n",
|
|
err);
|
|
return;
|
|
}
|
|
|
|
if (!mac_bridge.valid)
|
|
continue;
|
|
|
|
if (mac_bridge.val[1] & GSWIP_TABLE_MAC_BRIDGE_STATIC)
|
|
continue;
|
|
|
|
if (((mac_bridge.val[0] & GENMASK(7, 4)) >> 4) != port)
|
|
continue;
|
|
|
|
mac_bridge.valid = false;
|
|
err = gswip_pce_table_entry_write(priv, &mac_bridge);
|
|
if (err) {
|
|
dev_err(priv->dev, "failed to write mac bridge: %d\n",
|
|
err);
|
|
return;
|
|
}
|
|
}
|
|
}
|
|
|
|
static void gswip_port_stp_state_set(struct dsa_switch *ds, int port, u8 state)
|
|
{
|
|
struct gswip_priv *priv = ds->priv;
|
|
u32 stp_state;
|
|
|
|
switch (state) {
|
|
case BR_STATE_DISABLED:
|
|
gswip_switch_mask(priv, GSWIP_SDMA_PCTRL_EN, 0,
|
|
GSWIP_SDMA_PCTRLp(port));
|
|
return;
|
|
case BR_STATE_BLOCKING:
|
|
case BR_STATE_LISTENING:
|
|
stp_state = GSWIP_PCE_PCTRL_0_PSTATE_LISTEN;
|
|
break;
|
|
case BR_STATE_LEARNING:
|
|
stp_state = GSWIP_PCE_PCTRL_0_PSTATE_LEARNING;
|
|
break;
|
|
case BR_STATE_FORWARDING:
|
|
stp_state = GSWIP_PCE_PCTRL_0_PSTATE_FORWARDING;
|
|
break;
|
|
default:
|
|
dev_err(priv->dev, "invalid STP state: %d\n", state);
|
|
return;
|
|
}
|
|
|
|
gswip_switch_mask(priv, 0, GSWIP_SDMA_PCTRL_EN,
|
|
GSWIP_SDMA_PCTRLp(port));
|
|
gswip_switch_mask(priv, GSWIP_PCE_PCTRL_0_PSTATE_MASK, stp_state,
|
|
GSWIP_PCE_PCTRL_0p(port));
|
|
}
|
|
|
|
static int gswip_port_fdb(struct dsa_switch *ds, int port,
|
|
const unsigned char *addr, u16 vid, bool add)
|
|
{
|
|
struct gswip_priv *priv = ds->priv;
|
|
struct net_device *bridge = dsa_to_port(ds, port)->bridge_dev;
|
|
struct gswip_pce_table_entry mac_bridge = {0,};
|
|
unsigned int cpu_port = priv->hw_info->cpu_port;
|
|
int fid = -1;
|
|
int i;
|
|
int err;
|
|
|
|
if (!bridge)
|
|
return -EINVAL;
|
|
|
|
for (i = cpu_port; i < ARRAY_SIZE(priv->vlans); i++) {
|
|
if (priv->vlans[i].bridge == bridge) {
|
|
fid = priv->vlans[i].fid;
|
|
break;
|
|
}
|
|
}
|
|
|
|
if (fid == -1) {
|
|
dev_err(priv->dev, "Port not part of a bridge\n");
|
|
return -EINVAL;
|
|
}
|
|
|
|
mac_bridge.table = GSWIP_TABLE_MAC_BRIDGE;
|
|
mac_bridge.key_mode = true;
|
|
mac_bridge.key[0] = addr[5] | (addr[4] << 8);
|
|
mac_bridge.key[1] = addr[3] | (addr[2] << 8);
|
|
mac_bridge.key[2] = addr[1] | (addr[0] << 8);
|
|
mac_bridge.key[3] = fid;
|
|
mac_bridge.val[0] = add ? BIT(port) : 0; /* port map */
|
|
mac_bridge.val[1] = GSWIP_TABLE_MAC_BRIDGE_STATIC;
|
|
mac_bridge.valid = add;
|
|
|
|
err = gswip_pce_table_entry_write(priv, &mac_bridge);
|
|
if (err)
|
|
dev_err(priv->dev, "failed to write mac bridge: %d\n", err);
|
|
|
|
return err;
|
|
}
|
|
|
|
static int gswip_port_fdb_add(struct dsa_switch *ds, int port,
|
|
const unsigned char *addr, u16 vid)
|
|
{
|
|
return gswip_port_fdb(ds, port, addr, vid, true);
|
|
}
|
|
|
|
static int gswip_port_fdb_del(struct dsa_switch *ds, int port,
|
|
const unsigned char *addr, u16 vid)
|
|
{
|
|
return gswip_port_fdb(ds, port, addr, vid, false);
|
|
}
|
|
|
|
static int gswip_port_fdb_dump(struct dsa_switch *ds, int port,
|
|
dsa_fdb_dump_cb_t *cb, void *data)
|
|
{
|
|
struct gswip_priv *priv = ds->priv;
|
|
struct gswip_pce_table_entry mac_bridge = {0,};
|
|
unsigned char addr[6];
|
|
int i;
|
|
int err;
|
|
|
|
for (i = 0; i < 2048; i++) {
|
|
mac_bridge.table = GSWIP_TABLE_MAC_BRIDGE;
|
|
mac_bridge.index = i;
|
|
|
|
err = gswip_pce_table_entry_read(priv, &mac_bridge);
|
|
if (err) {
|
|
dev_err(priv->dev, "failed to write mac bridge: %d\n",
|
|
err);
|
|
return err;
|
|
}
|
|
|
|
if (!mac_bridge.valid)
|
|
continue;
|
|
|
|
addr[5] = mac_bridge.key[0] & 0xff;
|
|
addr[4] = (mac_bridge.key[0] >> 8) & 0xff;
|
|
addr[3] = mac_bridge.key[1] & 0xff;
|
|
addr[2] = (mac_bridge.key[1] >> 8) & 0xff;
|
|
addr[1] = mac_bridge.key[2] & 0xff;
|
|
addr[0] = (mac_bridge.key[2] >> 8) & 0xff;
|
|
if (mac_bridge.val[1] & GSWIP_TABLE_MAC_BRIDGE_STATIC) {
|
|
if (mac_bridge.val[0] & BIT(port))
|
|
cb(addr, 0, true, data);
|
|
} else {
|
|
if (((mac_bridge.val[0] & GENMASK(7, 4)) >> 4) == port)
|
|
cb(addr, 0, false, data);
|
|
}
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
static void gswip_phylink_validate(struct dsa_switch *ds, int port,
|
|
unsigned long *supported,
|
|
struct phylink_link_state *state)
|
|
{
|
|
__ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
|
|
|
|
switch (port) {
|
|
case 0:
|
|
case 1:
|
|
if (!phy_interface_mode_is_rgmii(state->interface) &&
|
|
state->interface != PHY_INTERFACE_MODE_MII &&
|
|
state->interface != PHY_INTERFACE_MODE_REVMII &&
|
|
state->interface != PHY_INTERFACE_MODE_RMII)
|
|
goto unsupported;
|
|
break;
|
|
case 2:
|
|
case 3:
|
|
case 4:
|
|
if (state->interface != PHY_INTERFACE_MODE_INTERNAL)
|
|
goto unsupported;
|
|
break;
|
|
case 5:
|
|
if (!phy_interface_mode_is_rgmii(state->interface) &&
|
|
state->interface != PHY_INTERFACE_MODE_INTERNAL)
|
|
goto unsupported;
|
|
break;
|
|
default:
|
|
bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
|
|
dev_err(ds->dev, "Unsupported port: %i\n", port);
|
|
return;
|
|
}
|
|
|
|
/* Allow all the expected bits */
|
|
phylink_set(mask, Autoneg);
|
|
phylink_set_port_modes(mask);
|
|
phylink_set(mask, Pause);
|
|
phylink_set(mask, Asym_Pause);
|
|
|
|
/* With the exclusion of MII and Reverse MII, we support Gigabit,
|
|
* including Half duplex
|
|
*/
|
|
if (state->interface != PHY_INTERFACE_MODE_MII &&
|
|
state->interface != PHY_INTERFACE_MODE_REVMII) {
|
|
phylink_set(mask, 1000baseT_Full);
|
|
phylink_set(mask, 1000baseT_Half);
|
|
}
|
|
|
|
phylink_set(mask, 10baseT_Half);
|
|
phylink_set(mask, 10baseT_Full);
|
|
phylink_set(mask, 100baseT_Half);
|
|
phylink_set(mask, 100baseT_Full);
|
|
|
|
bitmap_and(supported, supported, mask,
|
|
__ETHTOOL_LINK_MODE_MASK_NBITS);
|
|
bitmap_and(state->advertising, state->advertising, mask,
|
|
__ETHTOOL_LINK_MODE_MASK_NBITS);
|
|
return;
|
|
|
|
unsupported:
|
|
bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
|
|
dev_err(ds->dev, "Unsupported interface '%s' for port %d\n",
|
|
phy_modes(state->interface), port);
|
|
return;
|
|
}
|
|
|
|
static void gswip_phylink_mac_config(struct dsa_switch *ds, int port,
|
|
unsigned int mode,
|
|
const struct phylink_link_state *state)
|
|
{
|
|
struct gswip_priv *priv = ds->priv;
|
|
u32 miicfg = 0;
|
|
|
|
miicfg |= GSWIP_MII_CFG_LDCLKDIS;
|
|
|
|
switch (state->interface) {
|
|
case PHY_INTERFACE_MODE_MII:
|
|
case PHY_INTERFACE_MODE_INTERNAL:
|
|
miicfg |= GSWIP_MII_CFG_MODE_MIIM;
|
|
break;
|
|
case PHY_INTERFACE_MODE_REVMII:
|
|
miicfg |= GSWIP_MII_CFG_MODE_MIIP;
|
|
break;
|
|
case PHY_INTERFACE_MODE_RMII:
|
|
miicfg |= GSWIP_MII_CFG_MODE_RMIIM;
|
|
break;
|
|
case PHY_INTERFACE_MODE_RGMII:
|
|
case PHY_INTERFACE_MODE_RGMII_ID:
|
|
case PHY_INTERFACE_MODE_RGMII_RXID:
|
|
case PHY_INTERFACE_MODE_RGMII_TXID:
|
|
miicfg |= GSWIP_MII_CFG_MODE_RGMII;
|
|
break;
|
|
default:
|
|
dev_err(ds->dev,
|
|
"Unsupported interface: %d\n", state->interface);
|
|
return;
|
|
}
|
|
gswip_mii_mask_cfg(priv, GSWIP_MII_CFG_MODE_MASK, miicfg, port);
|
|
|
|
switch (state->interface) {
|
|
case PHY_INTERFACE_MODE_RGMII_ID:
|
|
gswip_mii_mask_pcdu(priv, GSWIP_MII_PCDU_TXDLY_MASK |
|
|
GSWIP_MII_PCDU_RXDLY_MASK, 0, port);
|
|
break;
|
|
case PHY_INTERFACE_MODE_RGMII_RXID:
|
|
gswip_mii_mask_pcdu(priv, GSWIP_MII_PCDU_RXDLY_MASK, 0, port);
|
|
break;
|
|
case PHY_INTERFACE_MODE_RGMII_TXID:
|
|
gswip_mii_mask_pcdu(priv, GSWIP_MII_PCDU_TXDLY_MASK, 0, port);
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
}
|
|
|
|
static void gswip_phylink_mac_link_down(struct dsa_switch *ds, int port,
|
|
unsigned int mode,
|
|
phy_interface_t interface)
|
|
{
|
|
struct gswip_priv *priv = ds->priv;
|
|
|
|
gswip_mii_mask_cfg(priv, GSWIP_MII_CFG_EN, 0, port);
|
|
}
|
|
|
|
static void gswip_phylink_mac_link_up(struct dsa_switch *ds, int port,
|
|
unsigned int mode,
|
|
phy_interface_t interface,
|
|
struct phy_device *phydev,
|
|
int speed, int duplex,
|
|
bool tx_pause, bool rx_pause)
|
|
{
|
|
struct gswip_priv *priv = ds->priv;
|
|
|
|
/* Enable the xMII interface only for the external PHY */
|
|
if (interface != PHY_INTERFACE_MODE_INTERNAL)
|
|
gswip_mii_mask_cfg(priv, 0, GSWIP_MII_CFG_EN, port);
|
|
}
|
|
|
|
static void gswip_get_strings(struct dsa_switch *ds, int port, u32 stringset,
|
|
uint8_t *data)
|
|
{
|
|
int i;
|
|
|
|
if (stringset != ETH_SS_STATS)
|
|
return;
|
|
|
|
for (i = 0; i < ARRAY_SIZE(gswip_rmon_cnt); i++)
|
|
strncpy(data + i * ETH_GSTRING_LEN, gswip_rmon_cnt[i].name,
|
|
ETH_GSTRING_LEN);
|
|
}
|
|
|
|
static u32 gswip_bcm_ram_entry_read(struct gswip_priv *priv, u32 table,
|
|
u32 index)
|
|
{
|
|
u32 result;
|
|
int err;
|
|
|
|
gswip_switch_w(priv, index, GSWIP_BM_RAM_ADDR);
|
|
gswip_switch_mask(priv, GSWIP_BM_RAM_CTRL_ADDR_MASK |
|
|
GSWIP_BM_RAM_CTRL_OPMOD,
|
|
table | GSWIP_BM_RAM_CTRL_BAS,
|
|
GSWIP_BM_RAM_CTRL);
|
|
|
|
err = gswip_switch_r_timeout(priv, GSWIP_BM_RAM_CTRL,
|
|
GSWIP_BM_RAM_CTRL_BAS);
|
|
if (err) {
|
|
dev_err(priv->dev, "timeout while reading table: %u, index: %u",
|
|
table, index);
|
|
return 0;
|
|
}
|
|
|
|
result = gswip_switch_r(priv, GSWIP_BM_RAM_VAL(0));
|
|
result |= gswip_switch_r(priv, GSWIP_BM_RAM_VAL(1)) << 16;
|
|
|
|
return result;
|
|
}
|
|
|
|
static void gswip_get_ethtool_stats(struct dsa_switch *ds, int port,
|
|
uint64_t *data)
|
|
{
|
|
struct gswip_priv *priv = ds->priv;
|
|
const struct gswip_rmon_cnt_desc *rmon_cnt;
|
|
int i;
|
|
u64 high;
|
|
|
|
for (i = 0; i < ARRAY_SIZE(gswip_rmon_cnt); i++) {
|
|
rmon_cnt = &gswip_rmon_cnt[i];
|
|
|
|
data[i] = gswip_bcm_ram_entry_read(priv, port,
|
|
rmon_cnt->offset);
|
|
if (rmon_cnt->size == 2) {
|
|
high = gswip_bcm_ram_entry_read(priv, port,
|
|
rmon_cnt->offset + 1);
|
|
data[i] |= high << 32;
|
|
}
|
|
}
|
|
}
|
|
|
|
static int gswip_get_sset_count(struct dsa_switch *ds, int port, int sset)
|
|
{
|
|
if (sset != ETH_SS_STATS)
|
|
return 0;
|
|
|
|
return ARRAY_SIZE(gswip_rmon_cnt);
|
|
}
|
|
|
|
static const struct dsa_switch_ops gswip_switch_ops = {
|
|
.get_tag_protocol = gswip_get_tag_protocol,
|
|
.setup = gswip_setup,
|
|
.port_enable = gswip_port_enable,
|
|
.port_disable = gswip_port_disable,
|
|
.port_bridge_join = gswip_port_bridge_join,
|
|
.port_bridge_leave = gswip_port_bridge_leave,
|
|
.port_fast_age = gswip_port_fast_age,
|
|
.port_vlan_filtering = gswip_port_vlan_filtering,
|
|
.port_vlan_prepare = gswip_port_vlan_prepare,
|
|
.port_vlan_add = gswip_port_vlan_add,
|
|
.port_vlan_del = gswip_port_vlan_del,
|
|
.port_stp_state_set = gswip_port_stp_state_set,
|
|
.port_fdb_add = gswip_port_fdb_add,
|
|
.port_fdb_del = gswip_port_fdb_del,
|
|
.port_fdb_dump = gswip_port_fdb_dump,
|
|
.phylink_validate = gswip_phylink_validate,
|
|
.phylink_mac_config = gswip_phylink_mac_config,
|
|
.phylink_mac_link_down = gswip_phylink_mac_link_down,
|
|
.phylink_mac_link_up = gswip_phylink_mac_link_up,
|
|
.get_strings = gswip_get_strings,
|
|
.get_ethtool_stats = gswip_get_ethtool_stats,
|
|
.get_sset_count = gswip_get_sset_count,
|
|
};
|
|
|
|
static const struct xway_gphy_match_data xrx200a1x_gphy_data = {
|
|
.fe_firmware_name = "lantiq/xrx200_phy22f_a14.bin",
|
|
.ge_firmware_name = "lantiq/xrx200_phy11g_a14.bin",
|
|
};
|
|
|
|
static const struct xway_gphy_match_data xrx200a2x_gphy_data = {
|
|
.fe_firmware_name = "lantiq/xrx200_phy22f_a22.bin",
|
|
.ge_firmware_name = "lantiq/xrx200_phy11g_a22.bin",
|
|
};
|
|
|
|
static const struct xway_gphy_match_data xrx300_gphy_data = {
|
|
.fe_firmware_name = "lantiq/xrx300_phy22f_a21.bin",
|
|
.ge_firmware_name = "lantiq/xrx300_phy11g_a21.bin",
|
|
};
|
|
|
|
static const struct of_device_id xway_gphy_match[] = {
|
|
{ .compatible = "lantiq,xrx200-gphy-fw", .data = NULL },
|
|
{ .compatible = "lantiq,xrx200a1x-gphy-fw", .data = &xrx200a1x_gphy_data },
|
|
{ .compatible = "lantiq,xrx200a2x-gphy-fw", .data = &xrx200a2x_gphy_data },
|
|
{ .compatible = "lantiq,xrx300-gphy-fw", .data = &xrx300_gphy_data },
|
|
{ .compatible = "lantiq,xrx330-gphy-fw", .data = &xrx300_gphy_data },
|
|
{},
|
|
};
|
|
|
|
static int gswip_gphy_fw_load(struct gswip_priv *priv, struct gswip_gphy_fw *gphy_fw)
|
|
{
|
|
struct device *dev = priv->dev;
|
|
const struct firmware *fw;
|
|
void *fw_addr;
|
|
dma_addr_t dma_addr;
|
|
dma_addr_t dev_addr;
|
|
size_t size;
|
|
int ret;
|
|
|
|
ret = clk_prepare_enable(gphy_fw->clk_gate);
|
|
if (ret)
|
|
return ret;
|
|
|
|
reset_control_assert(gphy_fw->reset);
|
|
|
|
ret = request_firmware(&fw, gphy_fw->fw_name, dev);
|
|
if (ret) {
|
|
dev_err(dev, "failed to load firmware: %s, error: %i\n",
|
|
gphy_fw->fw_name, ret);
|
|
return ret;
|
|
}
|
|
|
|
/* GPHY cores need the firmware code in a persistent and contiguous
|
|
* memory area with a 16 kB boundary aligned start address.
|
|
*/
|
|
size = fw->size + XRX200_GPHY_FW_ALIGN;
|
|
|
|
fw_addr = dmam_alloc_coherent(dev, size, &dma_addr, GFP_KERNEL);
|
|
if (fw_addr) {
|
|
fw_addr = PTR_ALIGN(fw_addr, XRX200_GPHY_FW_ALIGN);
|
|
dev_addr = ALIGN(dma_addr, XRX200_GPHY_FW_ALIGN);
|
|
memcpy(fw_addr, fw->data, fw->size);
|
|
} else {
|
|
dev_err(dev, "failed to alloc firmware memory\n");
|
|
release_firmware(fw);
|
|
return -ENOMEM;
|
|
}
|
|
|
|
release_firmware(fw);
|
|
|
|
ret = regmap_write(priv->rcu_regmap, gphy_fw->fw_addr_offset, dev_addr);
|
|
if (ret)
|
|
return ret;
|
|
|
|
reset_control_deassert(gphy_fw->reset);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int gswip_gphy_fw_probe(struct gswip_priv *priv,
|
|
struct gswip_gphy_fw *gphy_fw,
|
|
struct device_node *gphy_fw_np, int i)
|
|
{
|
|
struct device *dev = priv->dev;
|
|
u32 gphy_mode;
|
|
int ret;
|
|
char gphyname[10];
|
|
|
|
snprintf(gphyname, sizeof(gphyname), "gphy%d", i);
|
|
|
|
gphy_fw->clk_gate = devm_clk_get(dev, gphyname);
|
|
if (IS_ERR(gphy_fw->clk_gate)) {
|
|
dev_err(dev, "Failed to lookup gate clock\n");
|
|
return PTR_ERR(gphy_fw->clk_gate);
|
|
}
|
|
|
|
ret = of_property_read_u32(gphy_fw_np, "reg", &gphy_fw->fw_addr_offset);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = of_property_read_u32(gphy_fw_np, "lantiq,gphy-mode", &gphy_mode);
|
|
/* Default to GE mode */
|
|
if (ret)
|
|
gphy_mode = GPHY_MODE_GE;
|
|
|
|
switch (gphy_mode) {
|
|
case GPHY_MODE_FE:
|
|
gphy_fw->fw_name = priv->gphy_fw_name_cfg->fe_firmware_name;
|
|
break;
|
|
case GPHY_MODE_GE:
|
|
gphy_fw->fw_name = priv->gphy_fw_name_cfg->ge_firmware_name;
|
|
break;
|
|
default:
|
|
dev_err(dev, "Unknown GPHY mode %d\n", gphy_mode);
|
|
return -EINVAL;
|
|
}
|
|
|
|
gphy_fw->reset = of_reset_control_array_get_exclusive(gphy_fw_np);
|
|
if (IS_ERR(gphy_fw->reset)) {
|
|
if (PTR_ERR(gphy_fw->reset) != -EPROBE_DEFER)
|
|
dev_err(dev, "Failed to lookup gphy reset\n");
|
|
return PTR_ERR(gphy_fw->reset);
|
|
}
|
|
|
|
return gswip_gphy_fw_load(priv, gphy_fw);
|
|
}
|
|
|
|
static void gswip_gphy_fw_remove(struct gswip_priv *priv,
|
|
struct gswip_gphy_fw *gphy_fw)
|
|
{
|
|
int ret;
|
|
|
|
/* check if the device was fully probed */
|
|
if (!gphy_fw->fw_name)
|
|
return;
|
|
|
|
ret = regmap_write(priv->rcu_regmap, gphy_fw->fw_addr_offset, 0);
|
|
if (ret)
|
|
dev_err(priv->dev, "can not reset GPHY FW pointer");
|
|
|
|
clk_disable_unprepare(gphy_fw->clk_gate);
|
|
|
|
reset_control_put(gphy_fw->reset);
|
|
}
|
|
|
|
static int gswip_gphy_fw_list(struct gswip_priv *priv,
|
|
struct device_node *gphy_fw_list_np, u32 version)
|
|
{
|
|
struct device *dev = priv->dev;
|
|
struct device_node *gphy_fw_np;
|
|
const struct of_device_id *match;
|
|
int err;
|
|
int i = 0;
|
|
|
|
/* The VRX200 rev 1.1 uses the GSWIP 2.0 and needs the older
|
|
* GPHY firmware. The VRX200 rev 1.2 uses the GSWIP 2.1 and also
|
|
* needs a different GPHY firmware.
|
|
*/
|
|
if (of_device_is_compatible(gphy_fw_list_np, "lantiq,xrx200-gphy-fw")) {
|
|
switch (version) {
|
|
case GSWIP_VERSION_2_0:
|
|
priv->gphy_fw_name_cfg = &xrx200a1x_gphy_data;
|
|
break;
|
|
case GSWIP_VERSION_2_1:
|
|
priv->gphy_fw_name_cfg = &xrx200a2x_gphy_data;
|
|
break;
|
|
default:
|
|
dev_err(dev, "unknown GSWIP version: 0x%x", version);
|
|
return -ENOENT;
|
|
}
|
|
}
|
|
|
|
match = of_match_node(xway_gphy_match, gphy_fw_list_np);
|
|
if (match && match->data)
|
|
priv->gphy_fw_name_cfg = match->data;
|
|
|
|
if (!priv->gphy_fw_name_cfg) {
|
|
dev_err(dev, "GPHY compatible type not supported");
|
|
return -ENOENT;
|
|
}
|
|
|
|
priv->num_gphy_fw = of_get_available_child_count(gphy_fw_list_np);
|
|
if (!priv->num_gphy_fw)
|
|
return -ENOENT;
|
|
|
|
priv->rcu_regmap = syscon_regmap_lookup_by_phandle(gphy_fw_list_np,
|
|
"lantiq,rcu");
|
|
if (IS_ERR(priv->rcu_regmap))
|
|
return PTR_ERR(priv->rcu_regmap);
|
|
|
|
priv->gphy_fw = devm_kmalloc_array(dev, priv->num_gphy_fw,
|
|
sizeof(*priv->gphy_fw),
|
|
GFP_KERNEL | __GFP_ZERO);
|
|
if (!priv->gphy_fw)
|
|
return -ENOMEM;
|
|
|
|
for_each_available_child_of_node(gphy_fw_list_np, gphy_fw_np) {
|
|
err = gswip_gphy_fw_probe(priv, &priv->gphy_fw[i],
|
|
gphy_fw_np, i);
|
|
if (err)
|
|
goto remove_gphy;
|
|
i++;
|
|
}
|
|
|
|
return 0;
|
|
|
|
remove_gphy:
|
|
for (i = 0; i < priv->num_gphy_fw; i++)
|
|
gswip_gphy_fw_remove(priv, &priv->gphy_fw[i]);
|
|
return err;
|
|
}
|
|
|
|
static int gswip_probe(struct platform_device *pdev)
|
|
{
|
|
struct gswip_priv *priv;
|
|
struct device_node *mdio_np, *gphy_fw_np;
|
|
struct device *dev = &pdev->dev;
|
|
int err;
|
|
int i;
|
|
u32 version;
|
|
|
|
priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
|
|
if (!priv)
|
|
return -ENOMEM;
|
|
|
|
priv->gswip = devm_platform_ioremap_resource(pdev, 0);
|
|
if (IS_ERR(priv->gswip))
|
|
return PTR_ERR(priv->gswip);
|
|
|
|
priv->mdio = devm_platform_ioremap_resource(pdev, 1);
|
|
if (IS_ERR(priv->mdio))
|
|
return PTR_ERR(priv->mdio);
|
|
|
|
priv->mii = devm_platform_ioremap_resource(pdev, 2);
|
|
if (IS_ERR(priv->mii))
|
|
return PTR_ERR(priv->mii);
|
|
|
|
priv->hw_info = of_device_get_match_data(dev);
|
|
if (!priv->hw_info)
|
|
return -EINVAL;
|
|
|
|
priv->ds = devm_kzalloc(dev, sizeof(*priv->ds), GFP_KERNEL);
|
|
if (!priv->ds)
|
|
return -ENOMEM;
|
|
|
|
priv->ds->dev = dev;
|
|
priv->ds->num_ports = priv->hw_info->max_ports;
|
|
priv->ds->priv = priv;
|
|
priv->ds->ops = &gswip_switch_ops;
|
|
priv->dev = dev;
|
|
version = gswip_switch_r(priv, GSWIP_VERSION);
|
|
|
|
/* bring up the mdio bus */
|
|
gphy_fw_np = of_get_compatible_child(dev->of_node, "lantiq,gphy-fw");
|
|
if (gphy_fw_np) {
|
|
err = gswip_gphy_fw_list(priv, gphy_fw_np, version);
|
|
of_node_put(gphy_fw_np);
|
|
if (err) {
|
|
dev_err(dev, "gphy fw probe failed\n");
|
|
return err;
|
|
}
|
|
}
|
|
|
|
/* bring up the mdio bus */
|
|
mdio_np = of_get_compatible_child(dev->of_node, "lantiq,xrx200-mdio");
|
|
if (mdio_np) {
|
|
err = gswip_mdio(priv, mdio_np);
|
|
if (err) {
|
|
dev_err(dev, "mdio probe failed\n");
|
|
goto put_mdio_node;
|
|
}
|
|
}
|
|
|
|
err = dsa_register_switch(priv->ds);
|
|
if (err) {
|
|
dev_err(dev, "dsa switch register failed: %i\n", err);
|
|
goto mdio_bus;
|
|
}
|
|
if (!dsa_is_cpu_port(priv->ds, priv->hw_info->cpu_port)) {
|
|
dev_err(dev, "wrong CPU port defined, HW only supports port: %i",
|
|
priv->hw_info->cpu_port);
|
|
err = -EINVAL;
|
|
goto disable_switch;
|
|
}
|
|
|
|
platform_set_drvdata(pdev, priv);
|
|
|
|
dev_info(dev, "probed GSWIP version %lx mod %lx\n",
|
|
(version & GSWIP_VERSION_REV_MASK) >> GSWIP_VERSION_REV_SHIFT,
|
|
(version & GSWIP_VERSION_MOD_MASK) >> GSWIP_VERSION_MOD_SHIFT);
|
|
return 0;
|
|
|
|
disable_switch:
|
|
gswip_mdio_mask(priv, GSWIP_MDIO_GLOB_ENABLE, 0, GSWIP_MDIO_GLOB);
|
|
dsa_unregister_switch(priv->ds);
|
|
mdio_bus:
|
|
if (mdio_np)
|
|
mdiobus_unregister(priv->ds->slave_mii_bus);
|
|
put_mdio_node:
|
|
of_node_put(mdio_np);
|
|
for (i = 0; i < priv->num_gphy_fw; i++)
|
|
gswip_gphy_fw_remove(priv, &priv->gphy_fw[i]);
|
|
return err;
|
|
}
|
|
|
|
static int gswip_remove(struct platform_device *pdev)
|
|
{
|
|
struct gswip_priv *priv = platform_get_drvdata(pdev);
|
|
int i;
|
|
|
|
/* disable the switch */
|
|
gswip_mdio_mask(priv, GSWIP_MDIO_GLOB_ENABLE, 0, GSWIP_MDIO_GLOB);
|
|
|
|
dsa_unregister_switch(priv->ds);
|
|
|
|
if (priv->ds->slave_mii_bus) {
|
|
mdiobus_unregister(priv->ds->slave_mii_bus);
|
|
of_node_put(priv->ds->slave_mii_bus->dev.of_node);
|
|
}
|
|
|
|
for (i = 0; i < priv->num_gphy_fw; i++)
|
|
gswip_gphy_fw_remove(priv, &priv->gphy_fw[i]);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct gswip_hw_info gswip_xrx200 = {
|
|
.max_ports = 7,
|
|
.cpu_port = 6,
|
|
};
|
|
|
|
static const struct of_device_id gswip_of_match[] = {
|
|
{ .compatible = "lantiq,xrx200-gswip", .data = &gswip_xrx200 },
|
|
{},
|
|
};
|
|
MODULE_DEVICE_TABLE(of, gswip_of_match);
|
|
|
|
static struct platform_driver gswip_driver = {
|
|
.probe = gswip_probe,
|
|
.remove = gswip_remove,
|
|
.driver = {
|
|
.name = "gswip",
|
|
.of_match_table = gswip_of_match,
|
|
},
|
|
};
|
|
|
|
module_platform_driver(gswip_driver);
|
|
|
|
MODULE_FIRMWARE("lantiq/xrx300_phy11g_a21.bin");
|
|
MODULE_FIRMWARE("lantiq/xrx300_phy22f_a21.bin");
|
|
MODULE_FIRMWARE("lantiq/xrx200_phy11g_a14.bin");
|
|
MODULE_FIRMWARE("lantiq/xrx200_phy11g_a22.bin");
|
|
MODULE_FIRMWARE("lantiq/xrx200_phy22f_a14.bin");
|
|
MODULE_FIRMWARE("lantiq/xrx200_phy22f_a22.bin");
|
|
MODULE_AUTHOR("Hauke Mehrtens <hauke@hauke-m.de>");
|
|
MODULE_DESCRIPTION("Lantiq / Intel GSWIP driver");
|
|
MODULE_LICENSE("GPL v2");
|