897 lines
26 KiB
C
897 lines
26 KiB
C
/*
|
|
* Copyright (C) 2017 Pengutronix, Juergen Borleis <kernel@pengutronix.de>
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License
|
|
* version 2, as published by the Free Software Foundation.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
*/
|
|
#include <linux/kernel.h>
|
|
#include <linux/module.h>
|
|
#include <linux/gpio/consumer.h>
|
|
#include <linux/regmap.h>
|
|
#include <linux/mutex.h>
|
|
#include <linux/mii.h>
|
|
|
|
#include "lan9303.h"
|
|
|
|
#define LAN9303_NUM_PORTS 3
|
|
|
|
/* 13.2 System Control and Status Registers
|
|
* Multiply register number by 4 to get address offset.
|
|
*/
|
|
#define LAN9303_CHIP_REV 0x14
|
|
# define LAN9303_CHIP_ID 0x9303
|
|
#define LAN9303_IRQ_CFG 0x15
|
|
# define LAN9303_IRQ_CFG_IRQ_ENABLE BIT(8)
|
|
# define LAN9303_IRQ_CFG_IRQ_POL BIT(4)
|
|
# define LAN9303_IRQ_CFG_IRQ_TYPE BIT(0)
|
|
#define LAN9303_INT_STS 0x16
|
|
# define LAN9303_INT_STS_PHY_INT2 BIT(27)
|
|
# define LAN9303_INT_STS_PHY_INT1 BIT(26)
|
|
#define LAN9303_INT_EN 0x17
|
|
# define LAN9303_INT_EN_PHY_INT2_EN BIT(27)
|
|
# define LAN9303_INT_EN_PHY_INT1_EN BIT(26)
|
|
#define LAN9303_HW_CFG 0x1D
|
|
# define LAN9303_HW_CFG_READY BIT(27)
|
|
# define LAN9303_HW_CFG_AMDX_EN_PORT2 BIT(26)
|
|
# define LAN9303_HW_CFG_AMDX_EN_PORT1 BIT(25)
|
|
#define LAN9303_PMI_DATA 0x29
|
|
#define LAN9303_PMI_ACCESS 0x2A
|
|
# define LAN9303_PMI_ACCESS_PHY_ADDR(x) (((x) & 0x1f) << 11)
|
|
# define LAN9303_PMI_ACCESS_MIIRINDA(x) (((x) & 0x1f) << 6)
|
|
# define LAN9303_PMI_ACCESS_MII_BUSY BIT(0)
|
|
# define LAN9303_PMI_ACCESS_MII_WRITE BIT(1)
|
|
#define LAN9303_MANUAL_FC_1 0x68
|
|
#define LAN9303_MANUAL_FC_2 0x69
|
|
#define LAN9303_MANUAL_FC_0 0x6a
|
|
#define LAN9303_SWITCH_CSR_DATA 0x6b
|
|
#define LAN9303_SWITCH_CSR_CMD 0x6c
|
|
#define LAN9303_SWITCH_CSR_CMD_BUSY BIT(31)
|
|
#define LAN9303_SWITCH_CSR_CMD_RW BIT(30)
|
|
#define LAN9303_SWITCH_CSR_CMD_LANES (BIT(19) | BIT(18) | BIT(17) | BIT(16))
|
|
#define LAN9303_VIRT_PHY_BASE 0x70
|
|
#define LAN9303_VIRT_SPECIAL_CTRL 0x77
|
|
|
|
/*13.4 Switch Fabric Control and Status Registers
|
|
* Accessed indirectly via SWITCH_CSR_CMD, SWITCH_CSR_DATA.
|
|
*/
|
|
#define LAN9303_SW_DEV_ID 0x0000
|
|
#define LAN9303_SW_RESET 0x0001
|
|
#define LAN9303_SW_RESET_RESET BIT(0)
|
|
#define LAN9303_SW_IMR 0x0004
|
|
#define LAN9303_SW_IPR 0x0005
|
|
#define LAN9303_MAC_VER_ID_0 0x0400
|
|
#define LAN9303_MAC_RX_CFG_0 0x0401
|
|
# define LAN9303_MAC_RX_CFG_X_REJECT_MAC_TYPES BIT(1)
|
|
# define LAN9303_MAC_RX_CFG_X_RX_ENABLE BIT(0)
|
|
#define LAN9303_MAC_RX_UNDSZE_CNT_0 0x0410
|
|
#define LAN9303_MAC_RX_64_CNT_0 0x0411
|
|
#define LAN9303_MAC_RX_127_CNT_0 0x0412
|
|
#define LAN9303_MAC_RX_255_CNT_0 0x413
|
|
#define LAN9303_MAC_RX_511_CNT_0 0x0414
|
|
#define LAN9303_MAC_RX_1023_CNT_0 0x0415
|
|
#define LAN9303_MAC_RX_MAX_CNT_0 0x0416
|
|
#define LAN9303_MAC_RX_OVRSZE_CNT_0 0x0417
|
|
#define LAN9303_MAC_RX_PKTOK_CNT_0 0x0418
|
|
#define LAN9303_MAC_RX_CRCERR_CNT_0 0x0419
|
|
#define LAN9303_MAC_RX_MULCST_CNT_0 0x041a
|
|
#define LAN9303_MAC_RX_BRDCST_CNT_0 0x041b
|
|
#define LAN9303_MAC_RX_PAUSE_CNT_0 0x041c
|
|
#define LAN9303_MAC_RX_FRAG_CNT_0 0x041d
|
|
#define LAN9303_MAC_RX_JABB_CNT_0 0x041e
|
|
#define LAN9303_MAC_RX_ALIGN_CNT_0 0x041f
|
|
#define LAN9303_MAC_RX_PKTLEN_CNT_0 0x0420
|
|
#define LAN9303_MAC_RX_GOODPKTLEN_CNT_0 0x0421
|
|
#define LAN9303_MAC_RX_SYMBL_CNT_0 0x0422
|
|
#define LAN9303_MAC_RX_CTLFRM_CNT_0 0x0423
|
|
|
|
#define LAN9303_MAC_TX_CFG_0 0x0440
|
|
# define LAN9303_MAC_TX_CFG_X_TX_IFG_CONFIG_DEFAULT (21 << 2)
|
|
# define LAN9303_MAC_TX_CFG_X_TX_PAD_ENABLE BIT(1)
|
|
# define LAN9303_MAC_TX_CFG_X_TX_ENABLE BIT(0)
|
|
#define LAN9303_MAC_TX_DEFER_CNT_0 0x0451
|
|
#define LAN9303_MAC_TX_PAUSE_CNT_0 0x0452
|
|
#define LAN9303_MAC_TX_PKTOK_CNT_0 0x0453
|
|
#define LAN9303_MAC_TX_64_CNT_0 0x0454
|
|
#define LAN9303_MAC_TX_127_CNT_0 0x0455
|
|
#define LAN9303_MAC_TX_255_CNT_0 0x0456
|
|
#define LAN9303_MAC_TX_511_CNT_0 0x0457
|
|
#define LAN9303_MAC_TX_1023_CNT_0 0x0458
|
|
#define LAN9303_MAC_TX_MAX_CNT_0 0x0459
|
|
#define LAN9303_MAC_TX_UNDSZE_CNT_0 0x045a
|
|
#define LAN9303_MAC_TX_PKTLEN_CNT_0 0x045c
|
|
#define LAN9303_MAC_TX_BRDCST_CNT_0 0x045d
|
|
#define LAN9303_MAC_TX_MULCST_CNT_0 0x045e
|
|
#define LAN9303_MAC_TX_LATECOL_0 0x045f
|
|
#define LAN9303_MAC_TX_EXCOL_CNT_0 0x0460
|
|
#define LAN9303_MAC_TX_SNGLECOL_CNT_0 0x0461
|
|
#define LAN9303_MAC_TX_MULTICOL_CNT_0 0x0462
|
|
#define LAN9303_MAC_TX_TOTALCOL_CNT_0 0x0463
|
|
|
|
#define LAN9303_MAC_VER_ID_1 0x0800
|
|
#define LAN9303_MAC_RX_CFG_1 0x0801
|
|
#define LAN9303_MAC_TX_CFG_1 0x0840
|
|
#define LAN9303_MAC_VER_ID_2 0x0c00
|
|
#define LAN9303_MAC_RX_CFG_2 0x0c01
|
|
#define LAN9303_MAC_TX_CFG_2 0x0c40
|
|
#define LAN9303_SWE_ALR_CMD 0x1800
|
|
#define LAN9303_SWE_VLAN_CMD 0x180b
|
|
# define LAN9303_SWE_VLAN_CMD_RNW BIT(5)
|
|
# define LAN9303_SWE_VLAN_CMD_PVIDNVLAN BIT(4)
|
|
#define LAN9303_SWE_VLAN_WR_DATA 0x180c
|
|
#define LAN9303_SWE_VLAN_RD_DATA 0x180e
|
|
# define LAN9303_SWE_VLAN_MEMBER_PORT2 BIT(17)
|
|
# define LAN9303_SWE_VLAN_UNTAG_PORT2 BIT(16)
|
|
# define LAN9303_SWE_VLAN_MEMBER_PORT1 BIT(15)
|
|
# define LAN9303_SWE_VLAN_UNTAG_PORT1 BIT(14)
|
|
# define LAN9303_SWE_VLAN_MEMBER_PORT0 BIT(13)
|
|
# define LAN9303_SWE_VLAN_UNTAG_PORT0 BIT(12)
|
|
#define LAN9303_SWE_VLAN_CMD_STS 0x1810
|
|
#define LAN9303_SWE_GLB_INGRESS_CFG 0x1840
|
|
#define LAN9303_SWE_PORT_STATE 0x1843
|
|
# define LAN9303_SWE_PORT_STATE_FORWARDING_PORT2 (0)
|
|
# define LAN9303_SWE_PORT_STATE_LEARNING_PORT2 BIT(5)
|
|
# define LAN9303_SWE_PORT_STATE_BLOCKING_PORT2 BIT(4)
|
|
# define LAN9303_SWE_PORT_STATE_FORWARDING_PORT1 (0)
|
|
# define LAN9303_SWE_PORT_STATE_LEARNING_PORT1 BIT(3)
|
|
# define LAN9303_SWE_PORT_STATE_BLOCKING_PORT1 BIT(2)
|
|
# define LAN9303_SWE_PORT_STATE_FORWARDING_PORT0 (0)
|
|
# define LAN9303_SWE_PORT_STATE_LEARNING_PORT0 BIT(1)
|
|
# define LAN9303_SWE_PORT_STATE_BLOCKING_PORT0 BIT(0)
|
|
#define LAN9303_SWE_PORT_MIRROR 0x1846
|
|
# define LAN9303_SWE_PORT_MIRROR_SNIFF_ALL BIT(8)
|
|
# define LAN9303_SWE_PORT_MIRROR_SNIFFER_PORT2 BIT(7)
|
|
# define LAN9303_SWE_PORT_MIRROR_SNIFFER_PORT1 BIT(6)
|
|
# define LAN9303_SWE_PORT_MIRROR_SNIFFER_PORT0 BIT(5)
|
|
# define LAN9303_SWE_PORT_MIRROR_MIRRORED_PORT2 BIT(4)
|
|
# define LAN9303_SWE_PORT_MIRROR_MIRRORED_PORT1 BIT(3)
|
|
# define LAN9303_SWE_PORT_MIRROR_MIRRORED_PORT0 BIT(2)
|
|
# define LAN9303_SWE_PORT_MIRROR_ENABLE_RX_MIRRORING BIT(1)
|
|
# define LAN9303_SWE_PORT_MIRROR_ENABLE_TX_MIRRORING BIT(0)
|
|
#define LAN9303_SWE_INGRESS_PORT_TYPE 0x1847
|
|
#define LAN9303_BM_CFG 0x1c00
|
|
#define LAN9303_BM_EGRSS_PORT_TYPE 0x1c0c
|
|
# define LAN9303_BM_EGRSS_PORT_TYPE_SPECIAL_TAG_PORT2 (BIT(17) | BIT(16))
|
|
# define LAN9303_BM_EGRSS_PORT_TYPE_SPECIAL_TAG_PORT1 (BIT(9) | BIT(8))
|
|
# define LAN9303_BM_EGRSS_PORT_TYPE_SPECIAL_TAG_PORT0 (BIT(1) | BIT(0))
|
|
|
|
#define LAN9303_SWITCH_PORT_REG(port, reg0) (0x400 * (port) + (reg0))
|
|
|
|
/* the built-in PHYs are of type LAN911X */
|
|
#define MII_LAN911X_SPECIAL_MODES 0x12
|
|
#define MII_LAN911X_SPECIAL_CONTROL_STATUS 0x1f
|
|
|
|
static const struct regmap_range lan9303_valid_regs[] = {
|
|
regmap_reg_range(0x14, 0x17), /* misc, interrupt */
|
|
regmap_reg_range(0x19, 0x19), /* endian test */
|
|
regmap_reg_range(0x1d, 0x1d), /* hardware config */
|
|
regmap_reg_range(0x23, 0x24), /* general purpose timer */
|
|
regmap_reg_range(0x27, 0x27), /* counter */
|
|
regmap_reg_range(0x29, 0x2a), /* PMI index regs */
|
|
regmap_reg_range(0x68, 0x6a), /* flow control */
|
|
regmap_reg_range(0x6b, 0x6c), /* switch fabric indirect regs */
|
|
regmap_reg_range(0x6d, 0x6f), /* misc */
|
|
regmap_reg_range(0x70, 0x77), /* virtual phy */
|
|
regmap_reg_range(0x78, 0x7a), /* GPIO */
|
|
regmap_reg_range(0x7c, 0x7e), /* MAC & reset */
|
|
regmap_reg_range(0x80, 0xb7), /* switch fabric direct regs (wr only) */
|
|
};
|
|
|
|
static const struct regmap_range lan9303_reserved_ranges[] = {
|
|
regmap_reg_range(0x00, 0x13),
|
|
regmap_reg_range(0x18, 0x18),
|
|
regmap_reg_range(0x1a, 0x1c),
|
|
regmap_reg_range(0x1e, 0x22),
|
|
regmap_reg_range(0x25, 0x26),
|
|
regmap_reg_range(0x28, 0x28),
|
|
regmap_reg_range(0x2b, 0x67),
|
|
regmap_reg_range(0x7b, 0x7b),
|
|
regmap_reg_range(0x7f, 0x7f),
|
|
regmap_reg_range(0xb8, 0xff),
|
|
};
|
|
|
|
const struct regmap_access_table lan9303_register_set = {
|
|
.yes_ranges = lan9303_valid_regs,
|
|
.n_yes_ranges = ARRAY_SIZE(lan9303_valid_regs),
|
|
.no_ranges = lan9303_reserved_ranges,
|
|
.n_no_ranges = ARRAY_SIZE(lan9303_reserved_ranges),
|
|
};
|
|
EXPORT_SYMBOL(lan9303_register_set);
|
|
|
|
static int lan9303_read(struct regmap *regmap, unsigned int offset, u32 *reg)
|
|
{
|
|
int ret, i;
|
|
|
|
/* we can lose arbitration for the I2C case, because the device
|
|
* tries to detect and read an external EEPROM after reset and acts as
|
|
* a master on the shared I2C bus itself. This conflicts with our
|
|
* attempts to access the device as a slave at the same moment.
|
|
*/
|
|
for (i = 0; i < 5; i++) {
|
|
ret = regmap_read(regmap, offset, reg);
|
|
if (!ret)
|
|
return 0;
|
|
if (ret != -EAGAIN)
|
|
break;
|
|
msleep(500);
|
|
}
|
|
|
|
return -EIO;
|
|
}
|
|
|
|
static int lan9303_virt_phy_reg_read(struct lan9303 *chip, int regnum)
|
|
{
|
|
int ret;
|
|
u32 val;
|
|
|
|
if (regnum > MII_EXPANSION)
|
|
return -EINVAL;
|
|
|
|
ret = lan9303_read(chip->regmap, LAN9303_VIRT_PHY_BASE + regnum, &val);
|
|
if (ret)
|
|
return ret;
|
|
|
|
return val & 0xffff;
|
|
}
|
|
|
|
static int lan9303_virt_phy_reg_write(struct lan9303 *chip, int regnum, u16 val)
|
|
{
|
|
if (regnum > MII_EXPANSION)
|
|
return -EINVAL;
|
|
|
|
return regmap_write(chip->regmap, LAN9303_VIRT_PHY_BASE + regnum, val);
|
|
}
|
|
|
|
static int lan9303_indirect_phy_wait_for_completion(struct lan9303 *chip)
|
|
{
|
|
int ret, i;
|
|
u32 reg;
|
|
|
|
for (i = 0; i < 25; i++) {
|
|
ret = lan9303_read(chip->regmap, LAN9303_PMI_ACCESS, ®);
|
|
if (ret) {
|
|
dev_err(chip->dev,
|
|
"Failed to read pmi access status: %d\n", ret);
|
|
return ret;
|
|
}
|
|
if (!(reg & LAN9303_PMI_ACCESS_MII_BUSY))
|
|
return 0;
|
|
msleep(1);
|
|
}
|
|
|
|
return -EIO;
|
|
}
|
|
|
|
static int lan9303_indirect_phy_read(struct lan9303 *chip, int addr, int regnum)
|
|
{
|
|
int ret;
|
|
u32 val;
|
|
|
|
val = LAN9303_PMI_ACCESS_PHY_ADDR(addr);
|
|
val |= LAN9303_PMI_ACCESS_MIIRINDA(regnum);
|
|
|
|
mutex_lock(&chip->indirect_mutex);
|
|
|
|
ret = lan9303_indirect_phy_wait_for_completion(chip);
|
|
if (ret)
|
|
goto on_error;
|
|
|
|
/* start the MII read cycle */
|
|
ret = regmap_write(chip->regmap, LAN9303_PMI_ACCESS, val);
|
|
if (ret)
|
|
goto on_error;
|
|
|
|
ret = lan9303_indirect_phy_wait_for_completion(chip);
|
|
if (ret)
|
|
goto on_error;
|
|
|
|
/* read the result of this operation */
|
|
ret = lan9303_read(chip->regmap, LAN9303_PMI_DATA, &val);
|
|
if (ret)
|
|
goto on_error;
|
|
|
|
mutex_unlock(&chip->indirect_mutex);
|
|
|
|
return val & 0xffff;
|
|
|
|
on_error:
|
|
mutex_unlock(&chip->indirect_mutex);
|
|
return ret;
|
|
}
|
|
|
|
static int lan9303_indirect_phy_write(struct lan9303 *chip, int addr,
|
|
int regnum, u16 val)
|
|
{
|
|
int ret;
|
|
u32 reg;
|
|
|
|
reg = LAN9303_PMI_ACCESS_PHY_ADDR(addr);
|
|
reg |= LAN9303_PMI_ACCESS_MIIRINDA(regnum);
|
|
reg |= LAN9303_PMI_ACCESS_MII_WRITE;
|
|
|
|
mutex_lock(&chip->indirect_mutex);
|
|
|
|
ret = lan9303_indirect_phy_wait_for_completion(chip);
|
|
if (ret)
|
|
goto on_error;
|
|
|
|
/* write the data first... */
|
|
ret = regmap_write(chip->regmap, LAN9303_PMI_DATA, val);
|
|
if (ret)
|
|
goto on_error;
|
|
|
|
/* ...then start the MII write cycle */
|
|
ret = regmap_write(chip->regmap, LAN9303_PMI_ACCESS, reg);
|
|
|
|
on_error:
|
|
mutex_unlock(&chip->indirect_mutex);
|
|
return ret;
|
|
}
|
|
|
|
const struct lan9303_phy_ops lan9303_indirect_phy_ops = {
|
|
.phy_read = lan9303_indirect_phy_read,
|
|
.phy_write = lan9303_indirect_phy_write,
|
|
};
|
|
EXPORT_SYMBOL_GPL(lan9303_indirect_phy_ops);
|
|
|
|
static int lan9303_switch_wait_for_completion(struct lan9303 *chip)
|
|
{
|
|
int ret, i;
|
|
u32 reg;
|
|
|
|
for (i = 0; i < 25; i++) {
|
|
ret = lan9303_read(chip->regmap, LAN9303_SWITCH_CSR_CMD, ®);
|
|
if (ret) {
|
|
dev_err(chip->dev,
|
|
"Failed to read csr command status: %d\n", ret);
|
|
return ret;
|
|
}
|
|
if (!(reg & LAN9303_SWITCH_CSR_CMD_BUSY))
|
|
return 0;
|
|
msleep(1);
|
|
}
|
|
|
|
return -EIO;
|
|
}
|
|
|
|
static int lan9303_write_switch_reg(struct lan9303 *chip, u16 regnum, u32 val)
|
|
{
|
|
u32 reg;
|
|
int ret;
|
|
|
|
reg = regnum;
|
|
reg |= LAN9303_SWITCH_CSR_CMD_LANES;
|
|
reg |= LAN9303_SWITCH_CSR_CMD_BUSY;
|
|
|
|
mutex_lock(&chip->indirect_mutex);
|
|
|
|
ret = lan9303_switch_wait_for_completion(chip);
|
|
if (ret)
|
|
goto on_error;
|
|
|
|
ret = regmap_write(chip->regmap, LAN9303_SWITCH_CSR_DATA, val);
|
|
if (ret) {
|
|
dev_err(chip->dev, "Failed to write csr data reg: %d\n", ret);
|
|
goto on_error;
|
|
}
|
|
|
|
/* trigger write */
|
|
ret = regmap_write(chip->regmap, LAN9303_SWITCH_CSR_CMD, reg);
|
|
if (ret)
|
|
dev_err(chip->dev, "Failed to write csr command reg: %d\n",
|
|
ret);
|
|
|
|
on_error:
|
|
mutex_unlock(&chip->indirect_mutex);
|
|
return ret;
|
|
}
|
|
|
|
static int lan9303_read_switch_reg(struct lan9303 *chip, u16 regnum, u32 *val)
|
|
{
|
|
u32 reg;
|
|
int ret;
|
|
|
|
reg = regnum;
|
|
reg |= LAN9303_SWITCH_CSR_CMD_LANES;
|
|
reg |= LAN9303_SWITCH_CSR_CMD_RW;
|
|
reg |= LAN9303_SWITCH_CSR_CMD_BUSY;
|
|
|
|
mutex_lock(&chip->indirect_mutex);
|
|
|
|
ret = lan9303_switch_wait_for_completion(chip);
|
|
if (ret)
|
|
goto on_error;
|
|
|
|
/* trigger read */
|
|
ret = regmap_write(chip->regmap, LAN9303_SWITCH_CSR_CMD, reg);
|
|
if (ret) {
|
|
dev_err(chip->dev, "Failed to write csr command reg: %d\n",
|
|
ret);
|
|
goto on_error;
|
|
}
|
|
|
|
ret = lan9303_switch_wait_for_completion(chip);
|
|
if (ret)
|
|
goto on_error;
|
|
|
|
ret = lan9303_read(chip->regmap, LAN9303_SWITCH_CSR_DATA, val);
|
|
if (ret)
|
|
dev_err(chip->dev, "Failed to read csr data reg: %d\n", ret);
|
|
on_error:
|
|
mutex_unlock(&chip->indirect_mutex);
|
|
return ret;
|
|
}
|
|
|
|
static int lan9303_write_switch_port(struct lan9303 *chip, int port,
|
|
u16 regnum, u32 val)
|
|
{
|
|
return lan9303_write_switch_reg(
|
|
chip, LAN9303_SWITCH_PORT_REG(port, regnum), val);
|
|
}
|
|
|
|
static int lan9303_read_switch_port(struct lan9303 *chip, int port,
|
|
u16 regnum, u32 *val)
|
|
{
|
|
return lan9303_read_switch_reg(
|
|
chip, LAN9303_SWITCH_PORT_REG(port, regnum), val);
|
|
}
|
|
|
|
static int lan9303_detect_phy_setup(struct lan9303 *chip)
|
|
{
|
|
int reg;
|
|
|
|
/* depending on the 'phy_addr_sel_strap' setting, the three phys are
|
|
* using IDs 0-1-2 or IDs 1-2-3. We cannot read back the
|
|
* 'phy_addr_sel_strap' setting directly, so we need a test, which
|
|
* configuration is active:
|
|
* Special reg 18 of phy 3 reads as 0x0000, if 'phy_addr_sel_strap' is 0
|
|
* and the IDs are 0-1-2, else it contains something different from
|
|
* 0x0000, which means 'phy_addr_sel_strap' is 1 and the IDs are 1-2-3.
|
|
* 0xffff is returned on MDIO read with no response.
|
|
*/
|
|
reg = chip->ops->phy_read(chip, 3, MII_LAN911X_SPECIAL_MODES);
|
|
if (reg < 0) {
|
|
dev_err(chip->dev, "Failed to detect phy config: %d\n", reg);
|
|
return reg;
|
|
}
|
|
|
|
if ((reg != 0) && (reg != 0xffff))
|
|
chip->phy_addr_sel_strap = 1;
|
|
else
|
|
chip->phy_addr_sel_strap = 0;
|
|
|
|
dev_dbg(chip->dev, "Phy setup '%s' detected\n",
|
|
chip->phy_addr_sel_strap ? "1-2-3" : "0-1-2");
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int lan9303_disable_processing_port(struct lan9303 *chip,
|
|
unsigned int port)
|
|
{
|
|
int ret;
|
|
|
|
/* disable RX, but keep register reset default values else */
|
|
ret = lan9303_write_switch_port(chip, port, LAN9303_MAC_RX_CFG_0,
|
|
LAN9303_MAC_RX_CFG_X_REJECT_MAC_TYPES);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* disable TX, but keep register reset default values else */
|
|
return lan9303_write_switch_port(chip, port, LAN9303_MAC_TX_CFG_0,
|
|
LAN9303_MAC_TX_CFG_X_TX_IFG_CONFIG_DEFAULT |
|
|
LAN9303_MAC_TX_CFG_X_TX_PAD_ENABLE);
|
|
}
|
|
|
|
static int lan9303_enable_processing_port(struct lan9303 *chip,
|
|
unsigned int port)
|
|
{
|
|
int ret;
|
|
|
|
/* enable RX and keep register reset default values else */
|
|
ret = lan9303_write_switch_port(chip, port, LAN9303_MAC_RX_CFG_0,
|
|
LAN9303_MAC_RX_CFG_X_REJECT_MAC_TYPES |
|
|
LAN9303_MAC_RX_CFG_X_RX_ENABLE);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* enable TX and keep register reset default values else */
|
|
return lan9303_write_switch_port(chip, port, LAN9303_MAC_TX_CFG_0,
|
|
LAN9303_MAC_TX_CFG_X_TX_IFG_CONFIG_DEFAULT |
|
|
LAN9303_MAC_TX_CFG_X_TX_PAD_ENABLE |
|
|
LAN9303_MAC_TX_CFG_X_TX_ENABLE);
|
|
}
|
|
|
|
/* We want a special working switch:
|
|
* - do not forward packets between port 1 and 2
|
|
* - forward everything from port 1 to port 0
|
|
* - forward everything from port 2 to port 0
|
|
* - forward special tagged packets from port 0 to port 1 *or* port 2
|
|
*/
|
|
static int lan9303_separate_ports(struct lan9303 *chip)
|
|
{
|
|
int ret;
|
|
|
|
ret = lan9303_write_switch_reg(chip, LAN9303_SWE_PORT_MIRROR,
|
|
LAN9303_SWE_PORT_MIRROR_SNIFFER_PORT0 |
|
|
LAN9303_SWE_PORT_MIRROR_MIRRORED_PORT1 |
|
|
LAN9303_SWE_PORT_MIRROR_MIRRORED_PORT2 |
|
|
LAN9303_SWE_PORT_MIRROR_ENABLE_RX_MIRRORING |
|
|
LAN9303_SWE_PORT_MIRROR_SNIFF_ALL);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* enable defining the destination port via special VLAN tagging
|
|
* for port 0
|
|
*/
|
|
ret = lan9303_write_switch_reg(chip, LAN9303_SWE_INGRESS_PORT_TYPE,
|
|
0x03);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* tag incoming packets at port 1 and 2 on their way to port 0 to be
|
|
* able to discover their source port
|
|
*/
|
|
ret = lan9303_write_switch_reg(chip, LAN9303_BM_EGRSS_PORT_TYPE,
|
|
LAN9303_BM_EGRSS_PORT_TYPE_SPECIAL_TAG_PORT0);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* prevent port 1 and 2 from forwarding packets by their own */
|
|
return lan9303_write_switch_reg(chip, LAN9303_SWE_PORT_STATE,
|
|
LAN9303_SWE_PORT_STATE_FORWARDING_PORT0 |
|
|
LAN9303_SWE_PORT_STATE_BLOCKING_PORT1 |
|
|
LAN9303_SWE_PORT_STATE_BLOCKING_PORT2);
|
|
}
|
|
|
|
static int lan9303_handle_reset(struct lan9303 *chip)
|
|
{
|
|
if (!chip->reset_gpio)
|
|
return 0;
|
|
|
|
if (chip->reset_duration != 0)
|
|
msleep(chip->reset_duration);
|
|
|
|
/* release (deassert) reset and activate the device */
|
|
gpiod_set_value_cansleep(chip->reset_gpio, 0);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* stop processing packets for all ports */
|
|
static int lan9303_disable_processing(struct lan9303 *chip)
|
|
{
|
|
int p;
|
|
|
|
for (p = 0; p < LAN9303_NUM_PORTS; p++) {
|
|
int ret = lan9303_disable_processing_port(chip, p);
|
|
|
|
if (ret)
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int lan9303_check_device(struct lan9303 *chip)
|
|
{
|
|
int ret;
|
|
u32 reg;
|
|
|
|
ret = lan9303_read(chip->regmap, LAN9303_CHIP_REV, ®);
|
|
if (ret) {
|
|
dev_err(chip->dev, "failed to read chip revision register: %d\n",
|
|
ret);
|
|
if (!chip->reset_gpio) {
|
|
dev_dbg(chip->dev,
|
|
"hint: maybe failed due to missing reset GPIO\n");
|
|
}
|
|
return ret;
|
|
}
|
|
|
|
if ((reg >> 16) != LAN9303_CHIP_ID) {
|
|
dev_err(chip->dev, "expecting LAN9303 chip, but found: %X\n",
|
|
reg >> 16);
|
|
return ret;
|
|
}
|
|
|
|
/* The default state of the LAN9303 device is to forward packets between
|
|
* all ports (if not configured differently by an external EEPROM).
|
|
* The initial state of a DSA device must be forwarding packets only
|
|
* between the external and the internal ports and no forwarding
|
|
* between the external ports. In preparation we stop packet handling
|
|
* at all for now until the LAN9303 device is re-programmed accordingly.
|
|
*/
|
|
ret = lan9303_disable_processing(chip);
|
|
if (ret)
|
|
dev_warn(chip->dev, "failed to disable switching %d\n", ret);
|
|
|
|
dev_info(chip->dev, "Found LAN9303 rev. %u\n", reg & 0xffff);
|
|
|
|
ret = lan9303_detect_phy_setup(chip);
|
|
if (ret) {
|
|
dev_err(chip->dev,
|
|
"failed to discover phy bootstrap setup: %d\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* ---------------------------- DSA -----------------------------------*/
|
|
|
|
static enum dsa_tag_protocol lan9303_get_tag_protocol(struct dsa_switch *ds)
|
|
{
|
|
return DSA_TAG_PROTO_LAN9303;
|
|
}
|
|
|
|
static int lan9303_setup(struct dsa_switch *ds)
|
|
{
|
|
struct lan9303 *chip = ds->priv;
|
|
int ret;
|
|
|
|
/* Make sure that port 0 is the cpu port */
|
|
if (!dsa_is_cpu_port(ds, 0)) {
|
|
dev_err(chip->dev, "port 0 is not the CPU port\n");
|
|
return -EINVAL;
|
|
}
|
|
|
|
ret = lan9303_separate_ports(chip);
|
|
if (ret)
|
|
dev_err(chip->dev, "failed to separate ports %d\n", ret);
|
|
|
|
ret = lan9303_enable_processing_port(chip, 0);
|
|
if (ret)
|
|
dev_err(chip->dev, "failed to re-enable switching %d\n", ret);
|
|
|
|
return 0;
|
|
}
|
|
|
|
struct lan9303_mib_desc {
|
|
unsigned int offset; /* offset of first MAC */
|
|
const char *name;
|
|
};
|
|
|
|
static const struct lan9303_mib_desc lan9303_mib[] = {
|
|
{ .offset = LAN9303_MAC_RX_BRDCST_CNT_0, .name = "RxBroad", },
|
|
{ .offset = LAN9303_MAC_RX_PAUSE_CNT_0, .name = "RxPause", },
|
|
{ .offset = LAN9303_MAC_RX_MULCST_CNT_0, .name = "RxMulti", },
|
|
{ .offset = LAN9303_MAC_RX_PKTOK_CNT_0, .name = "RxOk", },
|
|
{ .offset = LAN9303_MAC_RX_CRCERR_CNT_0, .name = "RxCrcErr", },
|
|
{ .offset = LAN9303_MAC_RX_ALIGN_CNT_0, .name = "RxAlignErr", },
|
|
{ .offset = LAN9303_MAC_RX_JABB_CNT_0, .name = "RxJabber", },
|
|
{ .offset = LAN9303_MAC_RX_FRAG_CNT_0, .name = "RxFragment", },
|
|
{ .offset = LAN9303_MAC_RX_64_CNT_0, .name = "Rx64Byte", },
|
|
{ .offset = LAN9303_MAC_RX_127_CNT_0, .name = "Rx128Byte", },
|
|
{ .offset = LAN9303_MAC_RX_255_CNT_0, .name = "Rx256Byte", },
|
|
{ .offset = LAN9303_MAC_RX_511_CNT_0, .name = "Rx512Byte", },
|
|
{ .offset = LAN9303_MAC_RX_1023_CNT_0, .name = "Rx1024Byte", },
|
|
{ .offset = LAN9303_MAC_RX_MAX_CNT_0, .name = "RxMaxByte", },
|
|
{ .offset = LAN9303_MAC_RX_PKTLEN_CNT_0, .name = "RxByteCnt", },
|
|
{ .offset = LAN9303_MAC_RX_SYMBL_CNT_0, .name = "RxSymbolCnt", },
|
|
{ .offset = LAN9303_MAC_RX_CTLFRM_CNT_0, .name = "RxCfs", },
|
|
{ .offset = LAN9303_MAC_RX_OVRSZE_CNT_0, .name = "RxOverFlow", },
|
|
{ .offset = LAN9303_MAC_TX_UNDSZE_CNT_0, .name = "TxShort", },
|
|
{ .offset = LAN9303_MAC_TX_BRDCST_CNT_0, .name = "TxBroad", },
|
|
{ .offset = LAN9303_MAC_TX_PAUSE_CNT_0, .name = "TxPause", },
|
|
{ .offset = LAN9303_MAC_TX_MULCST_CNT_0, .name = "TxMulti", },
|
|
{ .offset = LAN9303_MAC_RX_UNDSZE_CNT_0, .name = "TxUnderRun", },
|
|
{ .offset = LAN9303_MAC_TX_64_CNT_0, .name = "Tx64Byte", },
|
|
{ .offset = LAN9303_MAC_TX_127_CNT_0, .name = "Tx128Byte", },
|
|
{ .offset = LAN9303_MAC_TX_255_CNT_0, .name = "Tx256Byte", },
|
|
{ .offset = LAN9303_MAC_TX_511_CNT_0, .name = "Tx512Byte", },
|
|
{ .offset = LAN9303_MAC_TX_1023_CNT_0, .name = "Tx1024Byte", },
|
|
{ .offset = LAN9303_MAC_TX_MAX_CNT_0, .name = "TxMaxByte", },
|
|
{ .offset = LAN9303_MAC_TX_PKTLEN_CNT_0, .name = "TxByteCnt", },
|
|
{ .offset = LAN9303_MAC_TX_PKTOK_CNT_0, .name = "TxOk", },
|
|
{ .offset = LAN9303_MAC_TX_TOTALCOL_CNT_0, .name = "TxCollision", },
|
|
{ .offset = LAN9303_MAC_TX_MULTICOL_CNT_0, .name = "TxMultiCol", },
|
|
{ .offset = LAN9303_MAC_TX_SNGLECOL_CNT_0, .name = "TxSingleCol", },
|
|
{ .offset = LAN9303_MAC_TX_EXCOL_CNT_0, .name = "TxExcCol", },
|
|
{ .offset = LAN9303_MAC_TX_DEFER_CNT_0, .name = "TxDefer", },
|
|
{ .offset = LAN9303_MAC_TX_LATECOL_0, .name = "TxLateCol", },
|
|
};
|
|
|
|
static void lan9303_get_strings(struct dsa_switch *ds, int port, uint8_t *data)
|
|
{
|
|
unsigned int u;
|
|
|
|
for (u = 0; u < ARRAY_SIZE(lan9303_mib); u++) {
|
|
strncpy(data + u * ETH_GSTRING_LEN, lan9303_mib[u].name,
|
|
ETH_GSTRING_LEN);
|
|
}
|
|
}
|
|
|
|
static void lan9303_get_ethtool_stats(struct dsa_switch *ds, int port,
|
|
uint64_t *data)
|
|
{
|
|
struct lan9303 *chip = ds->priv;
|
|
unsigned int u;
|
|
|
|
for (u = 0; u < ARRAY_SIZE(lan9303_mib); u++) {
|
|
u32 reg;
|
|
int ret;
|
|
|
|
ret = lan9303_read_switch_port(
|
|
chip, port, lan9303_mib[u].offset, ®);
|
|
|
|
if (ret)
|
|
dev_warn(chip->dev, "Reading status port %d reg %u failed\n",
|
|
port, lan9303_mib[u].offset);
|
|
data[u] = reg;
|
|
}
|
|
}
|
|
|
|
static int lan9303_get_sset_count(struct dsa_switch *ds)
|
|
{
|
|
return ARRAY_SIZE(lan9303_mib);
|
|
}
|
|
|
|
static int lan9303_phy_read(struct dsa_switch *ds, int phy, int regnum)
|
|
{
|
|
struct lan9303 *chip = ds->priv;
|
|
int phy_base = chip->phy_addr_sel_strap;
|
|
|
|
if (phy == phy_base)
|
|
return lan9303_virt_phy_reg_read(chip, regnum);
|
|
if (phy > phy_base + 2)
|
|
return -ENODEV;
|
|
|
|
return chip->ops->phy_read(chip, phy, regnum);
|
|
}
|
|
|
|
static int lan9303_phy_write(struct dsa_switch *ds, int phy, int regnum,
|
|
u16 val)
|
|
{
|
|
struct lan9303 *chip = ds->priv;
|
|
int phy_base = chip->phy_addr_sel_strap;
|
|
|
|
if (phy == phy_base)
|
|
return lan9303_virt_phy_reg_write(chip, regnum, val);
|
|
if (phy > phy_base + 2)
|
|
return -ENODEV;
|
|
|
|
return chip->ops->phy_write(chip, phy, regnum, val);
|
|
}
|
|
|
|
static int lan9303_port_enable(struct dsa_switch *ds, int port,
|
|
struct phy_device *phy)
|
|
{
|
|
struct lan9303 *chip = ds->priv;
|
|
|
|
/* enable internal packet processing */
|
|
switch (port) {
|
|
case 1:
|
|
case 2:
|
|
return lan9303_enable_processing_port(chip, port);
|
|
default:
|
|
dev_dbg(chip->dev,
|
|
"Error: request to power up invalid port %d\n", port);
|
|
}
|
|
|
|
return -ENODEV;
|
|
}
|
|
|
|
static void lan9303_port_disable(struct dsa_switch *ds, int port,
|
|
struct phy_device *phy)
|
|
{
|
|
struct lan9303 *chip = ds->priv;
|
|
|
|
/* disable internal packet processing */
|
|
switch (port) {
|
|
case 1:
|
|
case 2:
|
|
lan9303_disable_processing_port(chip, port);
|
|
lan9303_phy_write(ds, chip->phy_addr_sel_strap + port,
|
|
MII_BMCR, BMCR_PDOWN);
|
|
break;
|
|
default:
|
|
dev_dbg(chip->dev,
|
|
"Error: request to power down invalid port %d\n", port);
|
|
}
|
|
}
|
|
|
|
static const struct dsa_switch_ops lan9303_switch_ops = {
|
|
.get_tag_protocol = lan9303_get_tag_protocol,
|
|
.setup = lan9303_setup,
|
|
.get_strings = lan9303_get_strings,
|
|
.phy_read = lan9303_phy_read,
|
|
.phy_write = lan9303_phy_write,
|
|
.get_ethtool_stats = lan9303_get_ethtool_stats,
|
|
.get_sset_count = lan9303_get_sset_count,
|
|
.port_enable = lan9303_port_enable,
|
|
.port_disable = lan9303_port_disable,
|
|
};
|
|
|
|
static int lan9303_register_switch(struct lan9303 *chip)
|
|
{
|
|
chip->ds = dsa_switch_alloc(chip->dev, LAN9303_NUM_PORTS);
|
|
if (!chip->ds)
|
|
return -ENOMEM;
|
|
|
|
chip->ds->priv = chip;
|
|
chip->ds->ops = &lan9303_switch_ops;
|
|
chip->ds->phys_mii_mask = chip->phy_addr_sel_strap ? 0xe : 0x7;
|
|
|
|
return dsa_register_switch(chip->ds);
|
|
}
|
|
|
|
static void lan9303_probe_reset_gpio(struct lan9303 *chip,
|
|
struct device_node *np)
|
|
{
|
|
chip->reset_gpio = devm_gpiod_get_optional(chip->dev, "reset",
|
|
GPIOD_OUT_LOW);
|
|
|
|
if (!chip->reset_gpio) {
|
|
dev_dbg(chip->dev, "No reset GPIO defined\n");
|
|
return;
|
|
}
|
|
|
|
chip->reset_duration = 200;
|
|
|
|
if (np) {
|
|
of_property_read_u32(np, "reset-duration",
|
|
&chip->reset_duration);
|
|
} else {
|
|
dev_dbg(chip->dev, "reset duration defaults to 200 ms\n");
|
|
}
|
|
|
|
/* A sane reset duration should not be longer than 1s */
|
|
if (chip->reset_duration > 1000)
|
|
chip->reset_duration = 1000;
|
|
}
|
|
|
|
int lan9303_probe(struct lan9303 *chip, struct device_node *np)
|
|
{
|
|
int ret;
|
|
|
|
mutex_init(&chip->indirect_mutex);
|
|
|
|
lan9303_probe_reset_gpio(chip, np);
|
|
|
|
ret = lan9303_handle_reset(chip);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = lan9303_check_device(chip);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = lan9303_register_switch(chip);
|
|
if (ret) {
|
|
dev_dbg(chip->dev, "Failed to register switch: %d\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
EXPORT_SYMBOL(lan9303_probe);
|
|
|
|
int lan9303_remove(struct lan9303 *chip)
|
|
{
|
|
int rc;
|
|
|
|
rc = lan9303_disable_processing(chip);
|
|
if (rc != 0)
|
|
dev_warn(chip->dev, "shutting down failed\n");
|
|
|
|
dsa_unregister_switch(chip->ds);
|
|
|
|
/* assert reset to the whole device to prevent it from doing anything */
|
|
gpiod_set_value_cansleep(chip->reset_gpio, 1);
|
|
gpiod_unexport(chip->reset_gpio);
|
|
|
|
return 0;
|
|
}
|
|
EXPORT_SYMBOL(lan9303_remove);
|
|
|
|
MODULE_AUTHOR("Juergen Borleis <kernel@pengutronix.de>");
|
|
MODULE_DESCRIPTION("Core driver for SMSC/Microchip LAN9303 three port ethernet switch");
|
|
MODULE_LICENSE("GPL v2");
|