83 lines
3.6 KiB
Plaintext
83 lines
3.6 KiB
Plaintext
* Samsung I2S controller
|
|
|
|
Required SoC Specific Properties:
|
|
|
|
- compatible : should be one of the following.
|
|
- samsung,s3c6410-i2s: for 8/16/24bit stereo I2S.
|
|
- samsung,s5pv210-i2s: for 8/16/24bit multichannel(5.1) I2S with
|
|
secondary fifo, s/w reset control and internal mux for root clk src.
|
|
- samsung,exynos5420-i2s: for 8/16/24bit multichannel(5.1) I2S for
|
|
playback, sterio channel capture, secondary fifo using internal
|
|
or external dma, s/w reset control, internal mux for root clk src
|
|
and 7.1 channel TDM support for playback. TDM (Time division multiplexing)
|
|
is to allow transfer of multiple channel audio data on single data line.
|
|
- samsung,exynos7-i2s: with all the available features of exynos5 i2s,
|
|
exynos7 I2S has 7.1 channel TDM support for capture, secondary fifo
|
|
with only external dma and more no.of root clk sampling frequencies.
|
|
- samsung,exynos7-i2s1: I2S1 on previous samsung platforms supports
|
|
stereo channels. exynos7 i2s1 upgraded to 5.1 multichannel with
|
|
slightly modified bit offsets.
|
|
|
|
- reg: physical base address of the controller and length of memory mapped
|
|
region.
|
|
- dmas: list of DMA controller phandle and DMA request line ordered pairs.
|
|
- dma-names: identifier string for each DMA request line in the dmas property.
|
|
These strings correspond 1:1 with the ordered pairs in dmas.
|
|
- clocks: Handle to iis clock and RCLK source clk.
|
|
- clock-names:
|
|
i2s0 uses some base clks from CMU and some are from audio subsystem internal
|
|
clock controller. The clock names for i2s0 should be "iis", "i2s_opclk0" and
|
|
"i2s_opclk1" as shown in the example below.
|
|
i2s1 and i2s2 uses clocks from CMU. The clock names for i2s1 and i2s2 should
|
|
be "iis" and "i2s_opclk0".
|
|
"iis" is the i2s bus clock and i2s_opclk0, i2s_opclk1 are sources of the root
|
|
clk. i2s0 has internal mux to select the source of root clk and i2s1 and i2s2
|
|
doesn't have any such mux.
|
|
- #clock-cells: should be 1, this property must be present if the I2S device
|
|
is a clock provider in terms of the common clock bindings, described in
|
|
../clock/clock-bindings.txt.
|
|
- clock-output-names: from the common clock bindings, names of the CDCLK
|
|
I2S output clocks, suggested values are "i2s_cdclk0", "i2s_cdclk1",
|
|
"i2s_cdclk3" for the I2S0, I2S1, I2S2 devices recpectively.
|
|
|
|
There are following clocks available at the I2S device nodes:
|
|
CLK_I2S_CDCLK - the CDCLK (CODECLKO) gate clock,
|
|
CLK_I2S_RCLK_PSR - the RCLK prescaler divider clock (corresponding to the
|
|
IISPSR register),
|
|
CLK_I2S_RCLK_SRC - the RCLKSRC mux clock (corresponding to RCLKSRC bit in
|
|
IISMOD register).
|
|
|
|
Refer to the SoC datasheet for availability of the above clocks.
|
|
The CLK_I2S_RCLK_PSR and CLK_I2S_RCLK_SRC clocks are usually only available
|
|
in the IIS Multi Audio Interface (I2S0).
|
|
Note: Old DTs may not have the #clock-cells, clock-output-names properties
|
|
and then not use the I2S node as a clock supplier.
|
|
|
|
Optional SoC Specific Properties:
|
|
|
|
- samsung,idma-addr: Internal DMA register base address of the audio
|
|
sub system(used in secondary sound source).
|
|
- pinctrl-0: Should specify pin control groups used for this controller.
|
|
- pinctrl-names: Should contain only one value - "default".
|
|
|
|
|
|
Example:
|
|
|
|
i2s0: i2s@03830000 {
|
|
compatible = "samsung,s5pv210-i2s";
|
|
reg = <0x03830000 0x100>;
|
|
dmas = <&pdma0 10
|
|
&pdma0 9
|
|
&pdma0 8>;
|
|
dma-names = "tx", "rx", "tx-sec";
|
|
clocks = <&clock_audss EXYNOS_I2S_BUS>,
|
|
<&clock_audss EXYNOS_I2S_BUS>,
|
|
<&clock_audss EXYNOS_SCLK_I2S>;
|
|
clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
|
|
#clock-cells;
|
|
clock-output-names = "i2s_cdclk0";
|
|
samsung,idma-addr = <0x03000000>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&i2s0_bus>;
|
|
};
|