158 lines
5.5 KiB
Plaintext
158 lines
5.5 KiB
Plaintext
Kernel driver smm665
|
|
====================
|
|
|
|
Supported chips:
|
|
* Summit Microelectronics SMM465
|
|
Prefix: 'smm465'
|
|
Addresses scanned: -
|
|
Datasheet:
|
|
http://www.summitmicro.com/prod_select/summary/SMM465/SMM465DS.pdf
|
|
* Summit Microelectronics SMM665, SMM665B
|
|
Prefix: 'smm665'
|
|
Addresses scanned: -
|
|
Datasheet:
|
|
http://www.summitmicro.com/prod_select/summary/SMM665/SMM665B_2089_20.pdf
|
|
* Summit Microelectronics SMM665C
|
|
Prefix: 'smm665c'
|
|
Addresses scanned: -
|
|
Datasheet:
|
|
http://www.summitmicro.com/prod_select/summary/SMM665C/SMM665C_2125.pdf
|
|
* Summit Microelectronics SMM764
|
|
Prefix: 'smm764'
|
|
Addresses scanned: -
|
|
Datasheet:
|
|
http://www.summitmicro.com/prod_select/summary/SMM764/SMM764_2098.pdf
|
|
* Summit Microelectronics SMM766, SMM766B
|
|
Prefix: 'smm766'
|
|
Addresses scanned: -
|
|
Datasheets:
|
|
http://www.summitmicro.com/prod_select/summary/SMM766/SMM766_2086.pdf
|
|
http://www.summitmicro.com/prod_select/summary/SMM766B/SMM766B_2122.pdf
|
|
|
|
Author: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
|
|
|
|
Module Parameters
|
|
-----------------
|
|
|
|
* vref: int
|
|
Default: 1250 (mV)
|
|
Reference voltage on VREF_ADC pin in mV. It should not be necessary to set
|
|
this parameter unless a non-default reference voltage is used.
|
|
|
|
|
|
Description
|
|
-----------
|
|
|
|
[From datasheet] The SMM665 is an Active DC Output power supply Controller
|
|
that monitors, margins and cascade sequences power. The part monitors six
|
|
power supply channels as well as VDD, 12V input, two general-purpose analog
|
|
inputs and an internal temperature sensor using a 10-bit ADC.
|
|
|
|
Each monitored channel has its own high and low limits, plus a critical
|
|
limit.
|
|
|
|
Support for SMM465, SMM764, and SMM766 has been implemented but is untested.
|
|
|
|
|
|
Usage Notes
|
|
-----------
|
|
|
|
This driver does not probe for devices, since there is no register which
|
|
can be safely used to identify the chip. You will have to instantiate
|
|
the devices explicitly. When instantiating the device, you have to specify
|
|
its configuration register address.
|
|
|
|
Example: the following will load the driver for an SMM665 at address 0x57
|
|
on I2C bus #1:
|
|
$ modprobe smm665
|
|
$ echo smm665 0x57 > /sys/bus/i2c/devices/i2c-1/new_device
|
|
|
|
|
|
Sysfs entries
|
|
-------------
|
|
|
|
This driver uses the values in the datasheet to convert ADC register values
|
|
into the values specified in the sysfs-interface document. All attributes are
|
|
read only.
|
|
|
|
Min, max, lcrit, and crit values are used by the chip to trigger external signals
|
|
and/or other activity. Triggered signals can include HEALTHY, RST, Power Off,
|
|
or Fault depending on the chip configuration. The driver reports values as lcrit
|
|
or crit if exceeding the limits triggers RST, Power Off, or Fault, and as min or
|
|
max otherwise. For details please see the SMM665 datasheet.
|
|
|
|
For SMM465 and SMM764, values for Channel E and F are reported but undefined.
|
|
|
|
in1_input 12V input voltage (mV)
|
|
in2_input 3.3V (VDD) input voltage (mV)
|
|
in3_input Channel A voltage (mV)
|
|
in4_input Channel B voltage (mV)
|
|
in5_input Channel C voltage (mV)
|
|
in6_input Channel D voltage (mV)
|
|
in7_input Channel E voltage (mV)
|
|
in8_input Channel F voltage (mV)
|
|
in9_input AIN1 voltage (mV)
|
|
in10_input AIN2 voltage (mV)
|
|
|
|
in1_min 12v input minimum voltage (mV)
|
|
in2_min 3.3V (VDD) input minimum voltage (mV)
|
|
in3_min Channel A minimum voltage (mV)
|
|
in4_min Channel B minimum voltage (mV)
|
|
in5_min Channel C minimum voltage (mV)
|
|
in6_min Channel D minimum voltage (mV)
|
|
in7_min Channel E minimum voltage (mV)
|
|
in8_min Channel F minimum voltage (mV)
|
|
in9_min AIN1 minimum voltage (mV)
|
|
in10_min AIN2 minimum voltage (mV)
|
|
|
|
in1_max 12v input maximum voltage (mV)
|
|
in2_max 3.3V (VDD) input maximum voltage (mV)
|
|
in3_max Channel A maximum voltage (mV)
|
|
in4_max Channel B maximum voltage (mV)
|
|
in5_max Channel C maximum voltage (mV)
|
|
in6_max Channel D maximum voltage (mV)
|
|
in7_max Channel E maximum voltage (mV)
|
|
in8_max Channel F maximum voltage (mV)
|
|
in9_max AIN1 maximum voltage (mV)
|
|
in10_max AIN2 maximum voltage (mV)
|
|
|
|
in1_lcrit 12v input critical minimum voltage (mV)
|
|
in2_lcrit 3.3V (VDD) input critical minimum voltage (mV)
|
|
in3_lcrit Channel A critical minimum voltage (mV)
|
|
in4_lcrit Channel B critical minimum voltage (mV)
|
|
in5_lcrit Channel C critical minimum voltage (mV)
|
|
in6_lcrit Channel D critical minimum voltage (mV)
|
|
in7_lcrit Channel E critical minimum voltage (mV)
|
|
in8_lcrit Channel F critical minimum voltage (mV)
|
|
in9_lcrit AIN1 critical minimum voltage (mV)
|
|
in10_lcrit AIN2 critical minimum voltage (mV)
|
|
|
|
in1_crit 12v input critical maximum voltage (mV)
|
|
in2_crit 3.3V (VDD) input critical maximum voltage (mV)
|
|
in3_crit Channel A critical maximum voltage (mV)
|
|
in4_crit Channel B critical maximum voltage (mV)
|
|
in5_crit Channel C critical maximum voltage (mV)
|
|
in6_crit Channel D critical maximum voltage (mV)
|
|
in7_crit Channel E critical maximum voltage (mV)
|
|
in8_crit Channel F critical maximum voltage (mV)
|
|
in9_crit AIN1 critical maximum voltage (mV)
|
|
in10_crit AIN2 critical maximum voltage (mV)
|
|
|
|
in1_crit_alarm 12v input critical alarm
|
|
in2_crit_alarm 3.3V (VDD) input critical alarm
|
|
in3_crit_alarm Channel A critical alarm
|
|
in4_crit_alarm Channel B critical alarm
|
|
in5_crit_alarm Channel C critical alarm
|
|
in6_crit_alarm Channel D critical alarm
|
|
in7_crit_alarm Channel E critical alarm
|
|
in8_crit_alarm Channel F critical alarm
|
|
in9_crit_alarm AIN1 critical alarm
|
|
in10_crit_alarm AIN2 critical alarm
|
|
|
|
temp1_input Chip tempererature
|
|
temp1_min Mimimum chip tempererature
|
|
temp1_max Maximum chip tempererature
|
|
temp1_crit Critical chip tempererature
|
|
temp1_crit_alarm Temperature critical alarm
|