linux-sg2042/drivers/usb/host/xhci-rcar.c

165 lines
4.6 KiB
C

/*
* xHCI host controller driver for R-Car SoCs
*
* Copyright (C) 2014 Renesas Electronics Corporation
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*/
#include <linux/firmware.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/usb/phy.h>
#include "xhci.h"
#include "xhci-plat.h"
#include "xhci-rcar.h"
/*
* - The V2 firmware is possible to use on R-Car Gen2. However, the V2 causes
* performance degradation. So, this driver continues to use the V1 if R-Car
* Gen2.
* - The V1 firmware is impossible to use on R-Car Gen3.
*/
MODULE_FIRMWARE(XHCI_RCAR_FIRMWARE_NAME_V1);
MODULE_FIRMWARE(XHCI_RCAR_FIRMWARE_NAME_V2);
/*** Register Offset ***/
#define RCAR_USB3_INT_ENA 0x224 /* Interrupt Enable */
#define RCAR_USB3_DL_CTRL 0x250 /* FW Download Control & Status */
#define RCAR_USB3_FW_DATA0 0x258 /* FW Data0 */
#define RCAR_USB3_LCLK 0xa44 /* LCLK Select */
#define RCAR_USB3_CONF1 0xa48 /* USB3.0 Configuration1 */
#define RCAR_USB3_CONF2 0xa5c /* USB3.0 Configuration2 */
#define RCAR_USB3_CONF3 0xaa8 /* USB3.0 Configuration3 */
#define RCAR_USB3_RX_POL 0xab0 /* USB3.0 RX Polarity */
#define RCAR_USB3_TX_POL 0xab8 /* USB3.0 TX Polarity */
/*** Register Settings ***/
/* Interrupt Enable */
#define RCAR_USB3_INT_XHC_ENA 0x00000001
#define RCAR_USB3_INT_PME_ENA 0x00000002
#define RCAR_USB3_INT_HSE_ENA 0x00000004
#define RCAR_USB3_INT_ENA_VAL (RCAR_USB3_INT_XHC_ENA | \
RCAR_USB3_INT_PME_ENA | RCAR_USB3_INT_HSE_ENA)
/* FW Download Control & Status */
#define RCAR_USB3_DL_CTRL_ENABLE 0x00000001
#define RCAR_USB3_DL_CTRL_FW_SUCCESS 0x00000010
#define RCAR_USB3_DL_CTRL_FW_SET_DATA0 0x00000100
/* LCLK Select */
#define RCAR_USB3_LCLK_ENA_VAL 0x01030001
/* USB3.0 Configuration */
#define RCAR_USB3_CONF1_VAL 0x00030204
#define RCAR_USB3_CONF2_VAL 0x00030300
#define RCAR_USB3_CONF3_VAL 0x13802007
/* USB3.0 Polarity */
#define RCAR_USB3_RX_POL_VAL BIT(21)
#define RCAR_USB3_TX_POL_VAL BIT(4)
static void xhci_rcar_start_gen2(struct usb_hcd *hcd)
{
/* LCLK Select */
writel(RCAR_USB3_LCLK_ENA_VAL, hcd->regs + RCAR_USB3_LCLK);
/* USB3.0 Configuration */
writel(RCAR_USB3_CONF1_VAL, hcd->regs + RCAR_USB3_CONF1);
writel(RCAR_USB3_CONF2_VAL, hcd->regs + RCAR_USB3_CONF2);
writel(RCAR_USB3_CONF3_VAL, hcd->regs + RCAR_USB3_CONF3);
/* USB3.0 Polarity */
writel(RCAR_USB3_RX_POL_VAL, hcd->regs + RCAR_USB3_RX_POL);
writel(RCAR_USB3_TX_POL_VAL, hcd->regs + RCAR_USB3_TX_POL);
}
void xhci_rcar_start(struct usb_hcd *hcd)
{
u32 temp;
if (hcd->regs != NULL) {
/* Interrupt Enable */
temp = readl(hcd->regs + RCAR_USB3_INT_ENA);
temp |= RCAR_USB3_INT_ENA_VAL;
writel(temp, hcd->regs + RCAR_USB3_INT_ENA);
if (xhci_plat_type_is(hcd, XHCI_PLAT_TYPE_RENESAS_RCAR_GEN2))
xhci_rcar_start_gen2(hcd);
}
}
static int xhci_rcar_download_firmware(struct usb_hcd *hcd)
{
struct device *dev = hcd->self.controller;
void __iomem *regs = hcd->regs;
struct xhci_plat_priv *priv = hcd_to_xhci_priv(hcd);
const struct firmware *fw;
int retval, index, j, time;
int timeout = 10000;
u32 data, val, temp;
/* request R-Car USB3.0 firmware */
retval = request_firmware(&fw, priv->firmware_name, dev);
if (retval)
return retval;
/* download R-Car USB3.0 firmware */
temp = readl(regs + RCAR_USB3_DL_CTRL);
temp |= RCAR_USB3_DL_CTRL_ENABLE;
writel(temp, regs + RCAR_USB3_DL_CTRL);
for (index = 0; index < fw->size; index += 4) {
/* to avoid reading beyond the end of the buffer */
for (data = 0, j = 3; j >= 0; j--) {
if ((j + index) < fw->size)
data |= fw->data[index + j] << (8 * j);
}
writel(data, regs + RCAR_USB3_FW_DATA0);
temp = readl(regs + RCAR_USB3_DL_CTRL);
temp |= RCAR_USB3_DL_CTRL_FW_SET_DATA0;
writel(temp, regs + RCAR_USB3_DL_CTRL);
for (time = 0; time < timeout; time++) {
val = readl(regs + RCAR_USB3_DL_CTRL);
if ((val & RCAR_USB3_DL_CTRL_FW_SET_DATA0) == 0)
break;
udelay(1);
}
if (time == timeout) {
retval = -ETIMEDOUT;
break;
}
}
temp = readl(regs + RCAR_USB3_DL_CTRL);
temp &= ~RCAR_USB3_DL_CTRL_ENABLE;
writel(temp, regs + RCAR_USB3_DL_CTRL);
for (time = 0; time < timeout; time++) {
val = readl(regs + RCAR_USB3_DL_CTRL);
if (val & RCAR_USB3_DL_CTRL_FW_SUCCESS) {
retval = 0;
break;
}
udelay(1);
}
if (time == timeout)
retval = -ETIMEDOUT;
release_firmware(fw);
return retval;
}
/* This function needs to initialize a "phy" of usb before */
int xhci_rcar_init_quirk(struct usb_hcd *hcd)
{
/* If hcd->regs is NULL, we don't just call the following function */
if (!hcd->regs)
return 0;
return xhci_rcar_download_firmware(hcd);
}