linux-sg2042/net/dsa/mv88e6123_61_65.c

422 lines
10 KiB
C

/*
* net/dsa/mv88e6123_61_65.c - Marvell 88e6123/6161/6165 switch chip support
* Copyright (c) 2008 Marvell Semiconductor
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
#include <linux/list.h>
#include <linux/netdevice.h>
#include <linux/phy.h>
#include "dsa_priv.h"
#include "mv88e6xxx.h"
static char *mv88e6123_61_65_probe(struct mii_bus *bus, int sw_addr)
{
int ret;
ret = __mv88e6xxx_reg_read(bus, sw_addr, REG_PORT(0), 0x03);
if (ret >= 0) {
ret &= 0xfff0;
if (ret == 0x1210)
return "Marvell 88E6123";
if (ret == 0x1610)
return "Marvell 88E6161";
if (ret == 0x1650)
return "Marvell 88E6165";
}
return NULL;
}
static int mv88e6123_61_65_switch_reset(struct dsa_switch *ds)
{
int i;
int ret;
/*
* Set all ports to the disabled state.
*/
for (i = 0; i < 8; i++) {
ret = REG_READ(REG_PORT(i), 0x04);
REG_WRITE(REG_PORT(i), 0x04, ret & 0xfffc);
}
/*
* Wait for transmit queues to drain.
*/
msleep(2);
/*
* Reset the switch.
*/
REG_WRITE(REG_GLOBAL, 0x04, 0xc400);
/*
* Wait up to one second for reset to complete.
*/
for (i = 0; i < 1000; i++) {
ret = REG_READ(REG_GLOBAL, 0x00);
if ((ret & 0xc800) == 0xc800)
break;
msleep(1);
}
if (i == 1000)
return -ETIMEDOUT;
return 0;
}
static int mv88e6123_61_65_setup_global(struct dsa_switch *ds)
{
int ret;
int i;
/*
* Disable the PHY polling unit (since there won't be any
* external PHYs to poll), don't discard packets with
* excessive collisions, and mask all interrupt sources.
*/
REG_WRITE(REG_GLOBAL, 0x04, 0x0000);
/*
* Set the default address aging time to 5 minutes, and
* enable address learn messages to be sent to all message
* ports.
*/
REG_WRITE(REG_GLOBAL, 0x0a, 0x0148);
/*
* Configure the priority mapping registers.
*/
ret = mv88e6xxx_config_prio(ds);
if (ret < 0)
return ret;
/*
* Configure the cpu port, and configure the cpu port as the
* port to which ingress and egress monitor frames are to be
* sent.
*/
REG_WRITE(REG_GLOBAL, 0x1a, (ds->cpu_port * 0x1110));
/*
* Disable remote management for now, and set the switch's
* DSA device number to zero.
*/
REG_WRITE(REG_GLOBAL, 0x1c, 0x0000);
/*
* Send all frames with destination addresses matching
* 01:80:c2:00:00:2x to the CPU port.
*/
REG_WRITE(REG_GLOBAL2, 0x02, 0xffff);
/*
* Send all frames with destination addresses matching
* 01:80:c2:00:00:0x to the CPU port.
*/
REG_WRITE(REG_GLOBAL2, 0x03, 0xffff);
/*
* Disable the loopback filter, disable flow control
* messages, disable flood broadcast override, disable
* removing of provider tags, disable ATU age violation
* interrupts, disable tag flow control, force flow
* control priority to the highest, and send all special
* multicast frames to the CPU at the highest priority.
*/
REG_WRITE(REG_GLOBAL2, 0x05, 0x00ff);
/*
* Map all DSA device IDs to the CPU port.
*/
for (i = 0; i < 32; i++)
REG_WRITE(REG_GLOBAL2, 0x06, 0x8000 | (i << 8) | ds->cpu_port);
/*
* Clear all trunk masks.
*/
for (i = 0; i < 8; i++)
REG_WRITE(REG_GLOBAL2, 0x07, 0x8000 | (i << 12) | 0xff);
/*
* Clear all trunk mappings.
*/
for (i = 0; i < 16; i++)
REG_WRITE(REG_GLOBAL2, 0x08, 0x8000 | (i << 11));
/*
* Disable ingress rate limiting by resetting all ingress
* rate limit registers to their initial state.
*/
for (i = 0; i < 6; i++)
REG_WRITE(REG_GLOBAL2, 0x09, 0x9000 | (i << 8));
/*
* Initialise cross-chip port VLAN table to reset defaults.
*/
REG_WRITE(REG_GLOBAL2, 0x0b, 0x9000);
/*
* Clear the priority override table.
*/
for (i = 0; i < 16; i++)
REG_WRITE(REG_GLOBAL2, 0x0f, 0x8000 | (i << 8));
/* @@@ initialise AVB (22/23) watchdog (27) sdet (29) registers */
return 0;
}
static int mv88e6123_61_65_setup_port(struct dsa_switch *ds, int p)
{
int addr = REG_PORT(p);
/*
* MAC Forcing register: don't force link, speed, duplex
* or flow control state to any particular values.
*/
REG_WRITE(addr, 0x01, 0x0003);
/*
* Do not limit the period of time that this port can be
* paused for by the remote end or the period of time that
* this port can pause the remote end.
*/
REG_WRITE(addr, 0x02, 0x0000);
/*
* Port Control: disable Drop-on-Unlock, disable Drop-on-Lock,
* configure the requested (DSA/EDSA) tagging mode if this is
* the CPU port, disable Header mode, enable IGMP/MLD snooping,
* disable VLAN tunneling, determine priority by looking at
* 802.1p and IP priority fields (IP prio has precedence), and
* set STP state to Forwarding. Finally, if this is the CPU
* port, additionally enable forwarding of unknown unicast and
* multicast addresses.
*/
REG_WRITE(addr, 0x04,
(p == ds->cpu_port) ?
(ds->tag_protocol == htons(ETH_P_DSA)) ?
0x053f : 0x373f :
0x0433);
/*
* Port Control 1: disable trunking. Also, if this is the
* CPU port, enable learn messages to be sent to this port.
*/
REG_WRITE(addr, 0x05, (p == ds->cpu_port) ? 0x8000 : 0x0000);
/*
* Port based VLAN map: give each port its own address
* database, allow the CPU port to talk to each of the 'real'
* ports, and allow each of the 'real' ports to only talk to
* the CPU port.
*/
REG_WRITE(addr, 0x06,
((p & 0xf) << 12) |
((p == ds->cpu_port) ?
ds->valid_port_mask :
(1 << ds->cpu_port)));
/*
* Default VLAN ID and priority: don't set a default VLAN
* ID, and set the default packet priority to zero.
*/
REG_WRITE(addr, 0x07, 0x0000);
/*
* Port Control 2: don't force a good FCS, set the maximum
* frame size to 10240 bytes, don't let the switch add or
* strip 802.1q tags, don't discard tagged or untagged frames
* on this port, do a destination address lookup on all
* received packets as usual, disable ARP mirroring and don't
* send a copy of all transmitted/received frames on this port
* to the CPU.
*/
REG_WRITE(addr, 0x08, 0x2080);
/*
* Egress rate control: disable egress rate control.
*/
REG_WRITE(addr, 0x09, 0x0001);
/*
* Egress rate control 2: disable egress rate control.
*/
REG_WRITE(addr, 0x0a, 0x0000);
/*
* Port Association Vector: when learning source addresses
* of packets, add the address to the address database using
* a port bitmap that has only the bit for this port set and
* the other bits clear.
*/
REG_WRITE(addr, 0x0b, 1 << p);
/*
* Port ATU control: disable limiting the number of address
* database entries that this port is allowed to use.
*/
REG_WRITE(addr, 0x0c, 0x0000);
/*
* Priorit Override: disable DA, SA and VTU priority override.
*/
REG_WRITE(addr, 0x0d, 0x0000);
/*
* Port Ethertype: use the Ethertype DSA Ethertype value.
*/
REG_WRITE(addr, 0x0f, ETH_P_EDSA);
/*
* Tag Remap: use an identity 802.1p prio -> switch prio
* mapping.
*/
REG_WRITE(addr, 0x18, 0x3210);
/*
* Tag Remap 2: use an identity 802.1p prio -> switch prio
* mapping.
*/
REG_WRITE(addr, 0x19, 0x7654);
return 0;
}
static int mv88e6123_61_65_setup(struct dsa_switch *ds)
{
struct mv88e6xxx_priv_state *ps = (void *)(ds + 1);
int i;
int ret;
mutex_init(&ps->smi_mutex);
mutex_init(&ps->stats_mutex);
ret = mv88e6123_61_65_switch_reset(ds);
if (ret < 0)
return ret;
/* @@@ initialise vtu and atu */
ret = mv88e6123_61_65_setup_global(ds);
if (ret < 0)
return ret;
for (i = 0; i < 6; i++) {
ret = mv88e6123_61_65_setup_port(ds, i);
if (ret < 0)
return ret;
}
return 0;
}
static int mv88e6123_61_65_port_to_phy_addr(int port)
{
if (port >= 0 && port <= 4)
return port;
return -1;
}
static int
mv88e6123_61_65_phy_read(struct dsa_switch *ds, int port, int regnum)
{
int addr = mv88e6123_61_65_port_to_phy_addr(port);
return mv88e6xxx_phy_read(ds, addr, regnum);
}
static int
mv88e6123_61_65_phy_write(struct dsa_switch *ds,
int port, int regnum, u16 val)
{
int addr = mv88e6123_61_65_port_to_phy_addr(port);
return mv88e6xxx_phy_write(ds, addr, regnum, val);
}
static struct mv88e6xxx_hw_stat mv88e6123_61_65_hw_stats[] = {
{ "in_good_octets", 8, 0x00, },
{ "in_bad_octets", 4, 0x02, },
{ "in_unicast", 4, 0x04, },
{ "in_broadcasts", 4, 0x06, },
{ "in_multicasts", 4, 0x07, },
{ "in_pause", 4, 0x16, },
{ "in_undersize", 4, 0x18, },
{ "in_fragments", 4, 0x19, },
{ "in_oversize", 4, 0x1a, },
{ "in_jabber", 4, 0x1b, },
{ "in_rx_error", 4, 0x1c, },
{ "in_fcs_error", 4, 0x1d, },
{ "out_octets", 8, 0x0e, },
{ "out_unicast", 4, 0x10, },
{ "out_broadcasts", 4, 0x13, },
{ "out_multicasts", 4, 0x12, },
{ "out_pause", 4, 0x15, },
{ "excessive", 4, 0x11, },
{ "collisions", 4, 0x1e, },
{ "deferred", 4, 0x05, },
{ "single", 4, 0x14, },
{ "multiple", 4, 0x17, },
{ "out_fcs_error", 4, 0x03, },
{ "late", 4, 0x1f, },
{ "hist_64bytes", 4, 0x08, },
{ "hist_65_127bytes", 4, 0x09, },
{ "hist_128_255bytes", 4, 0x0a, },
{ "hist_256_511bytes", 4, 0x0b, },
{ "hist_512_1023bytes", 4, 0x0c, },
{ "hist_1024_max_bytes", 4, 0x0d, },
};
static void
mv88e6123_61_65_get_strings(struct dsa_switch *ds, int port, uint8_t *data)
{
mv88e6xxx_get_strings(ds, ARRAY_SIZE(mv88e6123_61_65_hw_stats),
mv88e6123_61_65_hw_stats, port, data);
}
static void
mv88e6123_61_65_get_ethtool_stats(struct dsa_switch *ds,
int port, uint64_t *data)
{
mv88e6xxx_get_ethtool_stats(ds, ARRAY_SIZE(mv88e6123_61_65_hw_stats),
mv88e6123_61_65_hw_stats, port, data);
}
static int mv88e6123_61_65_get_sset_count(struct dsa_switch *ds)
{
return ARRAY_SIZE(mv88e6123_61_65_hw_stats);
}
static struct dsa_switch_driver mv88e6123_61_65_switch_driver = {
.tag_protocol = __constant_htons(ETH_P_EDSA),
.priv_size = sizeof(struct mv88e6xxx_priv_state),
.probe = mv88e6123_61_65_probe,
.setup = mv88e6123_61_65_setup,
.set_addr = mv88e6xxx_set_addr_indirect,
.phy_read = mv88e6123_61_65_phy_read,
.phy_write = mv88e6123_61_65_phy_write,
.poll_link = mv88e6xxx_poll_link,
.get_strings = mv88e6123_61_65_get_strings,
.get_ethtool_stats = mv88e6123_61_65_get_ethtool_stats,
.get_sset_count = mv88e6123_61_65_get_sset_count,
};
int __init mv88e6123_61_65_init(void)
{
register_switch_driver(&mv88e6123_61_65_switch_driver);
return 0;
}
module_init(mv88e6123_61_65_init);
void __exit mv88e6123_61_65_cleanup(void)
{
unregister_switch_driver(&mv88e6123_61_65_switch_driver);
}
module_exit(mv88e6123_61_65_cleanup);