468 lines
13 KiB
C
468 lines
13 KiB
C
/*
|
|
* OMAP MPUSS low power code
|
|
*
|
|
* Copyright (C) 2011 Texas Instruments, Inc.
|
|
* Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
*
|
|
* OMAP4430 MPUSS mainly consists of dual Cortex-A9 with per-CPU
|
|
* Local timer and Watchdog, GIC, SCU, PL310 L2 cache controller,
|
|
* CPU0 and CPU1 LPRM modules.
|
|
* CPU0, CPU1 and MPUSS each have there own power domain and
|
|
* hence multiple low power combinations of MPUSS are possible.
|
|
*
|
|
* The CPU0 and CPU1 can't support Closed switch Retention (CSWR)
|
|
* because the mode is not supported by hw constraints of dormant
|
|
* mode. While waking up from the dormant mode, a reset signal
|
|
* to the Cortex-A9 processor must be asserted by the external
|
|
* power controller.
|
|
*
|
|
* With architectural inputs and hardware recommendations, only
|
|
* below modes are supported from power gain vs latency point of view.
|
|
*
|
|
* CPU0 CPU1 MPUSS
|
|
* ----------------------------------------------
|
|
* ON ON ON
|
|
* ON(Inactive) OFF ON(Inactive)
|
|
* OFF OFF CSWR
|
|
* OFF OFF OSWR
|
|
* OFF OFF OFF(Device OFF *TBD)
|
|
* ----------------------------------------------
|
|
*
|
|
* Note: CPU0 is the master core and it is the last CPU to go down
|
|
* and first to wake-up when MPUSS low power states are excercised
|
|
*
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
* published by the Free Software Foundation.
|
|
*/
|
|
|
|
#include <linux/kernel.h>
|
|
#include <linux/io.h>
|
|
#include <linux/errno.h>
|
|
#include <linux/linkage.h>
|
|
#include <linux/smp.h>
|
|
|
|
#include <asm/cacheflush.h>
|
|
#include <asm/tlbflush.h>
|
|
#include <asm/smp_scu.h>
|
|
#include <asm/pgalloc.h>
|
|
#include <asm/suspend.h>
|
|
#include <asm/hardware/cache-l2x0.h>
|
|
|
|
#include "soc.h"
|
|
#include "common.h"
|
|
#include "omap44xx.h"
|
|
#include "omap4-sar-layout.h"
|
|
#include "pm.h"
|
|
#include "prcm_mpu44xx.h"
|
|
#include "prcm_mpu54xx.h"
|
|
#include "prminst44xx.h"
|
|
#include "prcm44xx.h"
|
|
#include "prm44xx.h"
|
|
#include "prm-regbits-44xx.h"
|
|
|
|
static void __iomem *sar_base;
|
|
|
|
#if defined(CONFIG_PM) && defined(CONFIG_SMP)
|
|
|
|
struct omap4_cpu_pm_info {
|
|
struct powerdomain *pwrdm;
|
|
void __iomem *scu_sar_addr;
|
|
void __iomem *wkup_sar_addr;
|
|
void __iomem *l2x0_sar_addr;
|
|
};
|
|
|
|
/**
|
|
* struct cpu_pm_ops - CPU pm operations
|
|
* @finish_suspend: CPU suspend finisher function pointer
|
|
* @resume: CPU resume function pointer
|
|
* @scu_prepare: CPU Snoop Control program function pointer
|
|
* @hotplug_restart: CPU restart function pointer
|
|
*
|
|
* Structure holds functions pointer for CPU low power operations like
|
|
* suspend, resume and scu programming.
|
|
*/
|
|
struct cpu_pm_ops {
|
|
int (*finish_suspend)(unsigned long cpu_state);
|
|
void (*resume)(void);
|
|
void (*scu_prepare)(unsigned int cpu_id, unsigned int cpu_state);
|
|
void (*hotplug_restart)(void);
|
|
};
|
|
|
|
static DEFINE_PER_CPU(struct omap4_cpu_pm_info, omap4_pm_info);
|
|
static struct powerdomain *mpuss_pd;
|
|
static u32 cpu_context_offset;
|
|
|
|
static int default_finish_suspend(unsigned long cpu_state)
|
|
{
|
|
omap_do_wfi();
|
|
return 0;
|
|
}
|
|
|
|
static void dummy_cpu_resume(void)
|
|
{}
|
|
|
|
static void dummy_scu_prepare(unsigned int cpu_id, unsigned int cpu_state)
|
|
{}
|
|
|
|
static struct cpu_pm_ops omap_pm_ops = {
|
|
.finish_suspend = default_finish_suspend,
|
|
.resume = dummy_cpu_resume,
|
|
.scu_prepare = dummy_scu_prepare,
|
|
.hotplug_restart = dummy_cpu_resume,
|
|
};
|
|
|
|
/*
|
|
* Program the wakeup routine address for the CPU0 and CPU1
|
|
* used for OFF or DORMANT wakeup.
|
|
*/
|
|
static inline void set_cpu_wakeup_addr(unsigned int cpu_id, u32 addr)
|
|
{
|
|
struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu_id);
|
|
|
|
if (pm_info->wkup_sar_addr)
|
|
writel_relaxed(addr, pm_info->wkup_sar_addr);
|
|
}
|
|
|
|
/*
|
|
* Store the SCU power status value to scratchpad memory
|
|
*/
|
|
static void scu_pwrst_prepare(unsigned int cpu_id, unsigned int cpu_state)
|
|
{
|
|
struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu_id);
|
|
u32 scu_pwr_st;
|
|
|
|
switch (cpu_state) {
|
|
case PWRDM_POWER_RET:
|
|
scu_pwr_st = SCU_PM_DORMANT;
|
|
break;
|
|
case PWRDM_POWER_OFF:
|
|
scu_pwr_st = SCU_PM_POWEROFF;
|
|
break;
|
|
case PWRDM_POWER_ON:
|
|
case PWRDM_POWER_INACTIVE:
|
|
default:
|
|
scu_pwr_st = SCU_PM_NORMAL;
|
|
break;
|
|
}
|
|
|
|
if (pm_info->scu_sar_addr)
|
|
writel_relaxed(scu_pwr_st, pm_info->scu_sar_addr);
|
|
}
|
|
|
|
/* Helper functions for MPUSS OSWR */
|
|
static inline void mpuss_clear_prev_logic_pwrst(void)
|
|
{
|
|
u32 reg;
|
|
|
|
reg = omap4_prminst_read_inst_reg(OMAP4430_PRM_PARTITION,
|
|
OMAP4430_PRM_MPU_INST, OMAP4_RM_MPU_MPU_CONTEXT_OFFSET);
|
|
omap4_prminst_write_inst_reg(reg, OMAP4430_PRM_PARTITION,
|
|
OMAP4430_PRM_MPU_INST, OMAP4_RM_MPU_MPU_CONTEXT_OFFSET);
|
|
}
|
|
|
|
static inline void cpu_clear_prev_logic_pwrst(unsigned int cpu_id)
|
|
{
|
|
u32 reg;
|
|
|
|
if (cpu_id) {
|
|
reg = omap4_prcm_mpu_read_inst_reg(OMAP4430_PRCM_MPU_CPU1_INST,
|
|
cpu_context_offset);
|
|
omap4_prcm_mpu_write_inst_reg(reg, OMAP4430_PRCM_MPU_CPU1_INST,
|
|
cpu_context_offset);
|
|
} else {
|
|
reg = omap4_prcm_mpu_read_inst_reg(OMAP4430_PRCM_MPU_CPU0_INST,
|
|
cpu_context_offset);
|
|
omap4_prcm_mpu_write_inst_reg(reg, OMAP4430_PRCM_MPU_CPU0_INST,
|
|
cpu_context_offset);
|
|
}
|
|
}
|
|
|
|
/*
|
|
* Store the CPU cluster state for L2X0 low power operations.
|
|
*/
|
|
static void l2x0_pwrst_prepare(unsigned int cpu_id, unsigned int save_state)
|
|
{
|
|
struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu_id);
|
|
|
|
if (pm_info->l2x0_sar_addr)
|
|
writel_relaxed(save_state, pm_info->l2x0_sar_addr);
|
|
}
|
|
|
|
/*
|
|
* Save the L2X0 AUXCTRL and POR value to SAR memory. Its used to
|
|
* in every restore MPUSS OFF path.
|
|
*/
|
|
#ifdef CONFIG_CACHE_L2X0
|
|
static void __init save_l2x0_context(void)
|
|
{
|
|
void __iomem *l2x0_base = omap4_get_l2cache_base();
|
|
|
|
if (l2x0_base && sar_base) {
|
|
writel_relaxed(l2x0_saved_regs.aux_ctrl,
|
|
sar_base + L2X0_AUXCTRL_OFFSET);
|
|
writel_relaxed(l2x0_saved_regs.prefetch_ctrl,
|
|
sar_base + L2X0_PREFETCH_CTRL_OFFSET);
|
|
}
|
|
}
|
|
#else
|
|
static void __init save_l2x0_context(void)
|
|
{}
|
|
#endif
|
|
|
|
/**
|
|
* omap4_enter_lowpower: OMAP4 MPUSS Low Power Entry Function
|
|
* The purpose of this function is to manage low power programming
|
|
* of OMAP4 MPUSS subsystem
|
|
* @cpu : CPU ID
|
|
* @power_state: Low power state.
|
|
*
|
|
* MPUSS states for the context save:
|
|
* save_state =
|
|
* 0 - Nothing lost and no need to save: MPUSS INACTIVE
|
|
* 1 - CPUx L1 and logic lost: MPUSS CSWR
|
|
* 2 - CPUx L1 and logic lost + GIC lost: MPUSS OSWR
|
|
* 3 - CPUx L1 and logic lost + GIC + L2 lost: DEVICE OFF
|
|
*/
|
|
int omap4_enter_lowpower(unsigned int cpu, unsigned int power_state)
|
|
{
|
|
struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu);
|
|
unsigned int save_state = 0, cpu_logic_state = PWRDM_POWER_RET;
|
|
unsigned int wakeup_cpu;
|
|
|
|
if (omap_rev() == OMAP4430_REV_ES1_0)
|
|
return -ENXIO;
|
|
|
|
switch (power_state) {
|
|
case PWRDM_POWER_ON:
|
|
case PWRDM_POWER_INACTIVE:
|
|
save_state = 0;
|
|
break;
|
|
case PWRDM_POWER_OFF:
|
|
cpu_logic_state = PWRDM_POWER_OFF;
|
|
save_state = 1;
|
|
break;
|
|
case PWRDM_POWER_RET:
|
|
if (IS_PM44XX_ERRATUM(PM_OMAP4_CPU_OSWR_DISABLE)) {
|
|
save_state = 0;
|
|
break;
|
|
}
|
|
default:
|
|
/*
|
|
* CPUx CSWR is invalid hardware state. Also CPUx OSWR
|
|
* doesn't make much scense, since logic is lost and $L1
|
|
* needs to be cleaned because of coherency. This makes
|
|
* CPUx OSWR equivalent to CPUX OFF and hence not supported
|
|
*/
|
|
WARN_ON(1);
|
|
return -ENXIO;
|
|
}
|
|
|
|
pwrdm_pre_transition(NULL);
|
|
|
|
/*
|
|
* Check MPUSS next state and save interrupt controller if needed.
|
|
* In MPUSS OSWR or device OFF, interrupt controller contest is lost.
|
|
*/
|
|
mpuss_clear_prev_logic_pwrst();
|
|
if ((pwrdm_read_next_pwrst(mpuss_pd) == PWRDM_POWER_RET) &&
|
|
(pwrdm_read_logic_retst(mpuss_pd) == PWRDM_POWER_OFF))
|
|
save_state = 2;
|
|
|
|
cpu_clear_prev_logic_pwrst(cpu);
|
|
pwrdm_set_next_pwrst(pm_info->pwrdm, power_state);
|
|
pwrdm_set_logic_retst(pm_info->pwrdm, cpu_logic_state);
|
|
set_cpu_wakeup_addr(cpu, virt_to_phys(omap_pm_ops.resume));
|
|
omap_pm_ops.scu_prepare(cpu, power_state);
|
|
l2x0_pwrst_prepare(cpu, save_state);
|
|
|
|
/*
|
|
* Call low level function with targeted low power state.
|
|
*/
|
|
if (save_state)
|
|
cpu_suspend(save_state, omap_pm_ops.finish_suspend);
|
|
else
|
|
omap_pm_ops.finish_suspend(save_state);
|
|
|
|
if (IS_PM44XX_ERRATUM(PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD) && cpu)
|
|
gic_dist_enable();
|
|
|
|
/*
|
|
* Restore the CPUx power state to ON otherwise CPUx
|
|
* power domain can transitions to programmed low power
|
|
* state while doing WFI outside the low powe code. On
|
|
* secure devices, CPUx does WFI which can result in
|
|
* domain transition
|
|
*/
|
|
wakeup_cpu = smp_processor_id();
|
|
pwrdm_set_next_pwrst(pm_info->pwrdm, PWRDM_POWER_ON);
|
|
|
|
pwrdm_post_transition(NULL);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* omap4_hotplug_cpu: OMAP4 CPU hotplug entry
|
|
* @cpu : CPU ID
|
|
* @power_state: CPU low power state.
|
|
*/
|
|
int omap4_hotplug_cpu(unsigned int cpu, unsigned int power_state)
|
|
{
|
|
struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu);
|
|
unsigned int cpu_state = 0;
|
|
|
|
if (omap_rev() == OMAP4430_REV_ES1_0)
|
|
return -ENXIO;
|
|
|
|
/* Use the achievable power state for the domain */
|
|
power_state = pwrdm_get_valid_lp_state(pm_info->pwrdm,
|
|
false, power_state);
|
|
|
|
if (power_state == PWRDM_POWER_OFF)
|
|
cpu_state = 1;
|
|
|
|
pwrdm_clear_all_prev_pwrst(pm_info->pwrdm);
|
|
pwrdm_set_next_pwrst(pm_info->pwrdm, power_state);
|
|
set_cpu_wakeup_addr(cpu, virt_to_phys(omap_pm_ops.hotplug_restart));
|
|
omap_pm_ops.scu_prepare(cpu, power_state);
|
|
|
|
/*
|
|
* CPU never retuns back if targeted power state is OFF mode.
|
|
* CPU ONLINE follows normal CPU ONLINE ptah via
|
|
* omap4_secondary_startup().
|
|
*/
|
|
omap_pm_ops.finish_suspend(cpu_state);
|
|
|
|
pwrdm_set_next_pwrst(pm_info->pwrdm, PWRDM_POWER_ON);
|
|
return 0;
|
|
}
|
|
|
|
|
|
/*
|
|
* Enable Mercury Fast HG retention mode by default.
|
|
*/
|
|
static void enable_mercury_retention_mode(void)
|
|
{
|
|
u32 reg;
|
|
|
|
reg = omap4_prcm_mpu_read_inst_reg(OMAP54XX_PRCM_MPU_DEVICE_INST,
|
|
OMAP54XX_PRCM_MPU_PRM_PSCON_COUNT_OFFSET);
|
|
/* Enable HG_EN, HG_RAMPUP = fast mode */
|
|
reg |= BIT(24) | BIT(25);
|
|
omap4_prcm_mpu_write_inst_reg(reg, OMAP54XX_PRCM_MPU_DEVICE_INST,
|
|
OMAP54XX_PRCM_MPU_PRM_PSCON_COUNT_OFFSET);
|
|
}
|
|
|
|
/*
|
|
* Initialise OMAP4 MPUSS
|
|
*/
|
|
int __init omap4_mpuss_init(void)
|
|
{
|
|
struct omap4_cpu_pm_info *pm_info;
|
|
|
|
if (omap_rev() == OMAP4430_REV_ES1_0) {
|
|
WARN(1, "Power Management not supported on OMAP4430 ES1.0\n");
|
|
return -ENODEV;
|
|
}
|
|
|
|
/* Initilaise per CPU PM information */
|
|
pm_info = &per_cpu(omap4_pm_info, 0x0);
|
|
if (sar_base) {
|
|
pm_info->scu_sar_addr = sar_base + SCU_OFFSET0;
|
|
pm_info->wkup_sar_addr = sar_base +
|
|
CPU0_WAKEUP_NS_PA_ADDR_OFFSET;
|
|
pm_info->l2x0_sar_addr = sar_base + L2X0_SAVE_OFFSET0;
|
|
}
|
|
pm_info->pwrdm = pwrdm_lookup("cpu0_pwrdm");
|
|
if (!pm_info->pwrdm) {
|
|
pr_err("Lookup failed for CPU0 pwrdm\n");
|
|
return -ENODEV;
|
|
}
|
|
|
|
/* Clear CPU previous power domain state */
|
|
pwrdm_clear_all_prev_pwrst(pm_info->pwrdm);
|
|
cpu_clear_prev_logic_pwrst(0);
|
|
|
|
/* Initialise CPU0 power domain state to ON */
|
|
pwrdm_set_next_pwrst(pm_info->pwrdm, PWRDM_POWER_ON);
|
|
|
|
pm_info = &per_cpu(omap4_pm_info, 0x1);
|
|
if (sar_base) {
|
|
pm_info->scu_sar_addr = sar_base + SCU_OFFSET1;
|
|
pm_info->wkup_sar_addr = sar_base +
|
|
CPU1_WAKEUP_NS_PA_ADDR_OFFSET;
|
|
pm_info->l2x0_sar_addr = sar_base + L2X0_SAVE_OFFSET1;
|
|
}
|
|
|
|
pm_info->pwrdm = pwrdm_lookup("cpu1_pwrdm");
|
|
if (!pm_info->pwrdm) {
|
|
pr_err("Lookup failed for CPU1 pwrdm\n");
|
|
return -ENODEV;
|
|
}
|
|
|
|
/* Clear CPU previous power domain state */
|
|
pwrdm_clear_all_prev_pwrst(pm_info->pwrdm);
|
|
cpu_clear_prev_logic_pwrst(1);
|
|
|
|
/* Initialise CPU1 power domain state to ON */
|
|
pwrdm_set_next_pwrst(pm_info->pwrdm, PWRDM_POWER_ON);
|
|
|
|
mpuss_pd = pwrdm_lookup("mpu_pwrdm");
|
|
if (!mpuss_pd) {
|
|
pr_err("Failed to lookup MPUSS power domain\n");
|
|
return -ENODEV;
|
|
}
|
|
pwrdm_clear_all_prev_pwrst(mpuss_pd);
|
|
mpuss_clear_prev_logic_pwrst();
|
|
|
|
if (sar_base) {
|
|
/* Save device type on scratchpad for low level code to use */
|
|
writel_relaxed((omap_type() != OMAP2_DEVICE_TYPE_GP) ? 1 : 0,
|
|
sar_base + OMAP_TYPE_OFFSET);
|
|
save_l2x0_context();
|
|
}
|
|
|
|
if (cpu_is_omap44xx()) {
|
|
omap_pm_ops.finish_suspend = omap4_finish_suspend;
|
|
omap_pm_ops.resume = omap4_cpu_resume;
|
|
omap_pm_ops.scu_prepare = scu_pwrst_prepare;
|
|
omap_pm_ops.hotplug_restart = omap4_secondary_startup;
|
|
cpu_context_offset = OMAP4_RM_CPU0_CPU0_CONTEXT_OFFSET;
|
|
} else if (soc_is_omap54xx() || soc_is_dra7xx()) {
|
|
cpu_context_offset = OMAP54XX_RM_CPU0_CPU0_CONTEXT_OFFSET;
|
|
enable_mercury_retention_mode();
|
|
}
|
|
|
|
if (cpu_is_omap446x())
|
|
omap_pm_ops.hotplug_restart = omap4460_secondary_startup;
|
|
|
|
return 0;
|
|
}
|
|
|
|
#endif
|
|
|
|
/*
|
|
* For kexec, we must set CPU1_WAKEUP_NS_PA_ADDR to point to
|
|
* current kernel's secondary_startup() early before
|
|
* clockdomains_init(). Otherwise clockdomain_init() can
|
|
* wake CPU1 and cause a hang.
|
|
*/
|
|
void __init omap4_mpuss_early_init(void)
|
|
{
|
|
unsigned long startup_pa;
|
|
|
|
if (!cpu_is_omap44xx())
|
|
return;
|
|
|
|
sar_base = omap4_get_sar_ram_base();
|
|
|
|
if (cpu_is_omap443x())
|
|
startup_pa = virt_to_phys(omap4_secondary_startup);
|
|
else
|
|
startup_pa = virt_to_phys(omap4460_secondary_startup);
|
|
|
|
writel_relaxed(startup_pa, sar_base + CPU1_WAKEUP_NS_PA_ADDR_OFFSET);
|
|
}
|