236 lines
7.6 KiB
Plaintext
236 lines
7.6 KiB
Plaintext
Atmel NAND flash controller bindings
|
|
|
|
The NAND flash controller node should be defined under the EBI bus (see
|
|
Documentation/devicetree/bindings/memory-controllers/atmel,ebi.txt).
|
|
One or several NAND devices can be defined under this NAND controller.
|
|
The NAND controller might be connected to an ECC engine.
|
|
|
|
* NAND controller bindings:
|
|
|
|
Required properties:
|
|
- compatible: should be one of the following
|
|
"atmel,at91rm9200-nand-controller"
|
|
"atmel,at91sam9260-nand-controller"
|
|
"atmel,at91sam9261-nand-controller"
|
|
"atmel,at91sam9g45-nand-controller"
|
|
"atmel,sama5d3-nand-controller"
|
|
- ranges: empty ranges property to forward EBI ranges definitions.
|
|
- #address-cells: should be set to 2.
|
|
- #size-cells: should be set to 1.
|
|
- atmel,nfc-io: phandle to the NFC IO block. Only required for sama5d3
|
|
controllers.
|
|
- atmel,nfc-sram: phandle to the NFC SRAM block. Only required for sama5d3
|
|
controllers.
|
|
|
|
Optional properties:
|
|
- ecc-engine: phandle to the PMECC block. Only meaningful if the SoC embeds
|
|
a PMECC engine.
|
|
|
|
* NAND device/chip bindings:
|
|
|
|
Required properties:
|
|
- reg: describes the CS lines assigned to the NAND device. If the NAND device
|
|
exposes multiple CS lines (multi-dies chips), your reg property will
|
|
contain X tuples of 3 entries.
|
|
1st entry: the CS line this NAND chip is connected to
|
|
2nd entry: the base offset of the memory region assigned to this
|
|
device (always 0)
|
|
3rd entry: the memory region size (always 0x800000)
|
|
|
|
Optional properties:
|
|
- rb-gpios: the GPIO(s) used to check the Ready/Busy status of the NAND.
|
|
- cs-gpios: the GPIO(s) used to control the CS line.
|
|
- det-gpios: the GPIO used to detect if a Smartmedia Card is present.
|
|
- atmel,rb: an integer identifying the native Ready/Busy pin. Only meaningful
|
|
on sama5 SoCs.
|
|
|
|
All generic properties described in
|
|
Documentation/devicetree/bindings/mtd/{common,nand}.txt also apply to the NAND
|
|
device node, and NAND partitions should be defined under the NAND node as
|
|
described in Documentation/devicetree/bindings/mtd/partition.txt.
|
|
|
|
* ECC engine (PMECC) bindings:
|
|
|
|
Required properties:
|
|
- compatible: should be one of the following
|
|
"atmel,at91sam9g45-pmecc"
|
|
"atmel,sama5d4-pmecc"
|
|
"atmel,sama5d2-pmecc"
|
|
- reg: should contain 2 register ranges. The first one is pointing to the PMECC
|
|
block, and the second one to the PMECC_ERRLOC block.
|
|
|
|
* SAMA5 NFC I/O bindings:
|
|
|
|
SAMA5 SoCs embed an advanced NAND controller logic to automate READ/WRITE page
|
|
operations. This interface to this logic is placed in a separate I/O range and
|
|
should thus have its own DT node.
|
|
|
|
- compatible: should be "atmel,sama5d3-nfc-io", "syscon".
|
|
- reg: should contain the I/O range used to interact with the NFC logic.
|
|
|
|
Example:
|
|
|
|
nfc_io: nfc-io@70000000 {
|
|
compatible = "atmel,sama5d3-nfc-io", "syscon";
|
|
reg = <0x70000000 0x8000000>;
|
|
};
|
|
|
|
pmecc: ecc-engine@ffffc070 {
|
|
compatible = "atmel,at91sam9g45-pmecc";
|
|
reg = <0xffffc070 0x490>,
|
|
<0xffffc500 0x100>;
|
|
};
|
|
|
|
ebi: ebi@10000000 {
|
|
compatible = "atmel,sama5d3-ebi";
|
|
#address-cells = <2>;
|
|
#size-cells = <1>;
|
|
atmel,smc = <&hsmc>;
|
|
reg = <0x10000000 0x10000000
|
|
0x40000000 0x30000000>;
|
|
ranges = <0x0 0x0 0x10000000 0x10000000
|
|
0x1 0x0 0x40000000 0x10000000
|
|
0x2 0x0 0x50000000 0x10000000
|
|
0x3 0x0 0x60000000 0x10000000>;
|
|
clocks = <&mck>;
|
|
|
|
nand_controller: nand-controller {
|
|
compatible = "atmel,sama5d3-nand-controller";
|
|
atmel,nfc-sram = <&nfc_sram>;
|
|
atmel,nfc-io = <&nfc_io>;
|
|
ecc-engine = <&pmecc>;
|
|
#address-cells = <2>;
|
|
#size-cells = <1>;
|
|
ranges;
|
|
|
|
nand@3 {
|
|
reg = <0x3 0x0 0x800000>;
|
|
atmel,rb = <0>;
|
|
|
|
/*
|
|
* Put generic NAND/MTD properties and
|
|
* subnodes here.
|
|
*/
|
|
};
|
|
};
|
|
};
|
|
|
|
-----------------------------------------------------------------------
|
|
|
|
Deprecated bindings (should not be used in new device trees):
|
|
|
|
Required properties:
|
|
- compatible: The possible values are:
|
|
"atmel,at91rm9200-nand"
|
|
"atmel,sama5d2-nand"
|
|
"atmel,sama5d4-nand"
|
|
- reg : should specify localbus address and size used for the chip,
|
|
and hardware ECC controller if available.
|
|
If the hardware ECC is PMECC, it should contain address and size for
|
|
PMECC and PMECC Error Location controller.
|
|
The PMECC lookup table address and size in ROM is optional. If not
|
|
specified, driver will build it in runtime.
|
|
- atmel,nand-addr-offset : offset for the address latch.
|
|
- atmel,nand-cmd-offset : offset for the command latch.
|
|
- #address-cells, #size-cells : Must be present if the device has sub-nodes
|
|
representing partitions.
|
|
|
|
- gpios : specifies the gpio pins to control the NAND device. detect is an
|
|
optional gpio and may be set to 0 if not present.
|
|
|
|
Optional properties:
|
|
- atmel,nand-has-dma : boolean to support dma transfer for nand read/write.
|
|
- nand-ecc-mode : String, operation mode of the NAND ecc mode, soft by default.
|
|
Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first",
|
|
"soft_bch".
|
|
- atmel,has-pmecc : boolean to enable Programmable Multibit ECC hardware,
|
|
capable of BCH encoding and decoding, on devices where it is present.
|
|
- atmel,pmecc-cap : error correct capability for Programmable Multibit ECC
|
|
Controller. Supported values are: 2, 4, 8, 12, 24. If the compatible string
|
|
is "atmel,sama5d2-nand", 32 is also valid.
|
|
- atmel,pmecc-sector-size : sector size for ECC computation. Supported values
|
|
are: 512, 1024.
|
|
- atmel,pmecc-lookup-table-offset : includes two offsets of lookup table in ROM
|
|
for different sector size. First one is for sector size 512, the next is for
|
|
sector size 1024. If not specified, driver will build the table in runtime.
|
|
- nand-bus-width : 8 or 16 bus width if not present 8
|
|
- nand-on-flash-bbt: boolean to enable on flash bbt option if not present false
|
|
|
|
Nand Flash Controller(NFC) is an optional sub-node
|
|
Required properties:
|
|
- compatible : "atmel,sama5d3-nfc".
|
|
- reg : should specify the address and size used for NFC command registers,
|
|
NFC registers and NFC SRAM. NFC SRAM address and size can be absent
|
|
if don't want to use it.
|
|
- clocks: phandle to the peripheral clock
|
|
Optional properties:
|
|
- atmel,write-by-sram: boolean to enable NFC write by SRAM.
|
|
|
|
Examples:
|
|
nand0: nand@40000000,0 {
|
|
compatible = "atmel,at91rm9200-nand";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
reg = <0x40000000 0x10000000
|
|
0xffffe800 0x200
|
|
>;
|
|
atmel,nand-addr-offset = <21>; /* ale */
|
|
atmel,nand-cmd-offset = <22>; /* cle */
|
|
nand-on-flash-bbt;
|
|
nand-ecc-mode = "soft";
|
|
gpios = <&pioC 13 0 /* rdy */
|
|
&pioC 14 0 /* nce */
|
|
0 /* cd */
|
|
>;
|
|
partition@0 {
|
|
...
|
|
};
|
|
};
|
|
|
|
/* for PMECC supported chips */
|
|
nand0: nand@40000000 {
|
|
compatible = "atmel,at91rm9200-nand";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
reg = < 0x40000000 0x10000000 /* bus addr & size */
|
|
0xffffe000 0x00000600 /* PMECC addr & size */
|
|
0xffffe600 0x00000200 /* PMECC ERRLOC addr & size */
|
|
0x00100000 0x00100000 /* ROM addr & size */
|
|
>;
|
|
atmel,nand-addr-offset = <21>; /* ale */
|
|
atmel,nand-cmd-offset = <22>; /* cle */
|
|
nand-on-flash-bbt;
|
|
nand-ecc-mode = "hw";
|
|
atmel,has-pmecc; /* enable PMECC */
|
|
atmel,pmecc-cap = <2>;
|
|
atmel,pmecc-sector-size = <512>;
|
|
atmel,pmecc-lookup-table-offset = <0x8000 0x10000>;
|
|
gpios = <&pioD 5 0 /* rdy */
|
|
&pioD 4 0 /* nce */
|
|
0 /* cd */
|
|
>;
|
|
partition@0 {
|
|
...
|
|
};
|
|
};
|
|
|
|
/* for NFC supported chips */
|
|
nand0: nand@40000000 {
|
|
compatible = "atmel,at91rm9200-nand";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ranges;
|
|
...
|
|
nfc@70000000 {
|
|
compatible = "atmel,sama5d3-nfc";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
clocks = <&hsmc_clk>
|
|
reg = <
|
|
0x70000000 0x10000000 /* NFC Command Registers */
|
|
0xffffc000 0x00000070 /* NFC HSMC regs */
|
|
0x00200000 0x00100000 /* NFC SRAM banks */
|
|
>;
|
|
};
|
|
};
|