201 lines
4.5 KiB
C
201 lines
4.5 KiB
C
/*
|
|
* board-og.c -- support for the OpenGear KS8695 based boards.
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
* published by the Free Software Foundation.
|
|
*/
|
|
|
|
#include <linux/kernel.h>
|
|
#include <linux/types.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/init.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/serial_8250.h>
|
|
#include <linux/gpio.h>
|
|
#include <linux/irq.h>
|
|
#include <asm/mach-types.h>
|
|
#include <asm/mach/arch.h>
|
|
#include <asm/mach/map.h>
|
|
#include <mach/devices.h>
|
|
#include <mach/regs-gpio.h>
|
|
#include <mach/gpio-ks8695.h>
|
|
#include "generic.h"
|
|
|
|
static int og_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
|
|
{
|
|
if (machine_is_im4004() && (slot == 8))
|
|
return KS8695_IRQ_EXTERN1;
|
|
return KS8695_IRQ_EXTERN0;
|
|
}
|
|
|
|
static struct ks8695_pci_cfg __initdata og_pci = {
|
|
.mode = KS8695_MODE_PCI,
|
|
.map_irq = og_pci_map_irq,
|
|
};
|
|
|
|
static void __init og_register_pci(void)
|
|
{
|
|
/* Initialize the GPIO lines for interrupt mode */
|
|
ks8695_gpio_interrupt(KS8695_GPIO_0, IRQ_TYPE_LEVEL_LOW);
|
|
|
|
/* Cardbus Slot */
|
|
if (machine_is_im4004())
|
|
ks8695_gpio_interrupt(KS8695_GPIO_1, IRQ_TYPE_LEVEL_LOW);
|
|
|
|
if (IS_ENABLED(CONFIG_PCI))
|
|
ks8695_init_pci(&og_pci);
|
|
}
|
|
|
|
/*
|
|
* The PCI bus reset is driven by a dedicated GPIO line. Toggle it here
|
|
* and bring the PCI bus out of reset.
|
|
*/
|
|
static void __init og_pci_bus_reset(void)
|
|
{
|
|
unsigned int rstline = 1;
|
|
|
|
/* Some boards use a different GPIO as the PCI reset line */
|
|
if (machine_is_im4004())
|
|
rstline = 2;
|
|
else if (machine_is_im42xx())
|
|
rstline = 0;
|
|
|
|
gpio_request(rstline, "PCI reset");
|
|
gpio_direction_output(rstline, 0);
|
|
|
|
/* Drive a reset on the PCI reset line */
|
|
gpio_set_value(rstline, 1);
|
|
gpio_set_value(rstline, 0);
|
|
mdelay(100);
|
|
gpio_set_value(rstline, 1);
|
|
mdelay(100);
|
|
}
|
|
|
|
/*
|
|
* Direct connect serial ports (non-PCI that is).
|
|
*/
|
|
#define S8250_PHYS 0x03800000
|
|
#define S8250_VIRT 0xf4000000
|
|
#define S8250_SIZE 0x00100000
|
|
|
|
static struct __initdata map_desc og_io_desc[] = {
|
|
{
|
|
.virtual = S8250_VIRT,
|
|
.pfn = __phys_to_pfn(S8250_PHYS),
|
|
.length = S8250_SIZE,
|
|
.type = MT_DEVICE,
|
|
}
|
|
};
|
|
|
|
static struct resource og_uart_resources[] = {
|
|
{
|
|
.start = S8250_VIRT,
|
|
.end = S8250_VIRT + S8250_SIZE,
|
|
.flags = IORESOURCE_MEM
|
|
},
|
|
};
|
|
|
|
static struct plat_serial8250_port og_uart_data[] = {
|
|
{
|
|
.mapbase = S8250_VIRT,
|
|
.membase = (char *) S8250_VIRT,
|
|
.irq = 3,
|
|
.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
|
|
.iotype = UPIO_MEM,
|
|
.regshift = 2,
|
|
.uartclk = 115200 * 16,
|
|
},
|
|
{ },
|
|
};
|
|
|
|
static struct platform_device og_uart = {
|
|
.name = "serial8250",
|
|
.id = 0,
|
|
.dev.platform_data = og_uart_data,
|
|
.num_resources = 1,
|
|
.resource = og_uart_resources
|
|
};
|
|
|
|
static struct platform_device *og_devices[] __initdata = {
|
|
&og_uart
|
|
};
|
|
|
|
static void __init og_init(void)
|
|
{
|
|
ks8695_register_gpios();
|
|
|
|
if (machine_is_cm4002()) {
|
|
ks8695_gpio_interrupt(KS8695_GPIO_1, IRQ_TYPE_LEVEL_HIGH);
|
|
iotable_init(og_io_desc, ARRAY_SIZE(og_io_desc));
|
|
platform_add_devices(og_devices, ARRAY_SIZE(og_devices));
|
|
} else {
|
|
og_pci_bus_reset();
|
|
og_register_pci();
|
|
}
|
|
|
|
ks8695_add_device_lan();
|
|
ks8695_add_device_wan();
|
|
}
|
|
|
|
#ifdef CONFIG_MACH_CM4002
|
|
MACHINE_START(CM4002, "OpenGear/CM4002")
|
|
/* OpenGear Inc. */
|
|
.atag_offset = 0x100,
|
|
.map_io = ks8695_map_io,
|
|
.init_irq = ks8695_init_irq,
|
|
.init_machine = og_init,
|
|
.init_time = ks8695_timer_init,
|
|
.restart = ks8695_restart,
|
|
MACHINE_END
|
|
#endif
|
|
|
|
#ifdef CONFIG_MACH_CM4008
|
|
MACHINE_START(CM4008, "OpenGear/CM4008")
|
|
/* OpenGear Inc. */
|
|
.atag_offset = 0x100,
|
|
.map_io = ks8695_map_io,
|
|
.init_irq = ks8695_init_irq,
|
|
.init_machine = og_init,
|
|
.init_time = ks8695_timer_init,
|
|
.restart = ks8695_restart,
|
|
MACHINE_END
|
|
#endif
|
|
|
|
#ifdef CONFIG_MACH_CM41xx
|
|
MACHINE_START(CM41XX, "OpenGear/CM41xx")
|
|
/* OpenGear Inc. */
|
|
.atag_offset = 0x100,
|
|
.map_io = ks8695_map_io,
|
|
.init_irq = ks8695_init_irq,
|
|
.init_machine = og_init,
|
|
.init_time = ks8695_timer_init,
|
|
.restart = ks8695_restart,
|
|
MACHINE_END
|
|
#endif
|
|
|
|
#ifdef CONFIG_MACH_IM4004
|
|
MACHINE_START(IM4004, "OpenGear/IM4004")
|
|
/* OpenGear Inc. */
|
|
.atag_offset = 0x100,
|
|
.map_io = ks8695_map_io,
|
|
.init_irq = ks8695_init_irq,
|
|
.init_machine = og_init,
|
|
.init_time = ks8695_timer_init,
|
|
.restart = ks8695_restart,
|
|
MACHINE_END
|
|
#endif
|
|
|
|
#ifdef CONFIG_MACH_IM42xx
|
|
MACHINE_START(IM42XX, "OpenGear/IM42xx")
|
|
/* OpenGear Inc. */
|
|
.atag_offset = 0x100,
|
|
.map_io = ks8695_map_io,
|
|
.init_irq = ks8695_init_irq,
|
|
.init_machine = og_init,
|
|
.init_time = ks8695_timer_init,
|
|
.restart = ks8695_restart,
|
|
MACHINE_END
|
|
#endif
|