908 lines
31 KiB
ReStructuredText
908 lines
31 KiB
ReStructuredText
=================================================
|
|
Using kgdb, kdb and the kernel debugger internals
|
|
=================================================
|
|
|
|
:Author: Jason Wessel
|
|
|
|
Introduction
|
|
============
|
|
|
|
The kernel has two different debugger front ends (kdb and kgdb) which
|
|
interface to the debug core. It is possible to use either of the
|
|
debugger front ends and dynamically transition between them if you
|
|
configure the kernel properly at compile and runtime.
|
|
|
|
Kdb is simplistic shell-style interface which you can use on a system
|
|
console with a keyboard or serial console. You can use it to inspect
|
|
memory, registers, process lists, dmesg, and even set breakpoints to
|
|
stop in a certain location. Kdb is not a source level debugger, although
|
|
you can set breakpoints and execute some basic kernel run control. Kdb
|
|
is mainly aimed at doing some analysis to aid in development or
|
|
diagnosing kernel problems. You can access some symbols by name in
|
|
kernel built-ins or in kernel modules if the code was built with
|
|
``CONFIG_KALLSYMS``.
|
|
|
|
Kgdb is intended to be used as a source level debugger for the Linux
|
|
kernel. It is used along with gdb to debug a Linux kernel. The
|
|
expectation is that gdb can be used to "break in" to the kernel to
|
|
inspect memory, variables and look through call stack information
|
|
similar to the way an application developer would use gdb to debug an
|
|
application. It is possible to place breakpoints in kernel code and
|
|
perform some limited execution stepping.
|
|
|
|
Two machines are required for using kgdb. One of these machines is a
|
|
development machine and the other is the target machine. The kernel to
|
|
be debugged runs on the target machine. The development machine runs an
|
|
instance of gdb against the vmlinux file which contains the symbols (not
|
|
a boot image such as bzImage, zImage, uImage...). In gdb the developer
|
|
specifies the connection parameters and connects to kgdb. The type of
|
|
connection a developer makes with gdb depends on the availability of
|
|
kgdb I/O modules compiled as built-ins or loadable kernel modules in the
|
|
test machine's kernel.
|
|
|
|
Compiling a kernel
|
|
==================
|
|
|
|
- In order to enable compilation of kdb, you must first enable kgdb.
|
|
|
|
- The kgdb test compile options are described in the kgdb test suite
|
|
chapter.
|
|
|
|
Kernel config options for kgdb
|
|
------------------------------
|
|
|
|
To enable ``CONFIG_KGDB`` you should look under
|
|
:menuselection:`Kernel hacking --> Kernel debugging` and select
|
|
:menuselection:`KGDB: kernel debugger`.
|
|
|
|
While it is not a hard requirement that you have symbols in your vmlinux
|
|
file, gdb tends not to be very useful without the symbolic data, so you
|
|
will want to turn on ``CONFIG_DEBUG_INFO`` which is called
|
|
:menuselection:`Compile the kernel with debug info` in the config menu.
|
|
|
|
It is advised, but not required, that you turn on the
|
|
``CONFIG_FRAME_POINTER`` kernel option which is called :menuselection:`Compile
|
|
the kernel with frame pointers` in the config menu. This option inserts code
|
|
to into the compiled executable which saves the frame information in
|
|
registers or on the stack at different points which allows a debugger
|
|
such as gdb to more accurately construct stack back traces while
|
|
debugging the kernel.
|
|
|
|
If the architecture that you are using supports the kernel option
|
|
``CONFIG_STRICT_KERNEL_RWX``, you should consider turning it off. This
|
|
option will prevent the use of software breakpoints because it marks
|
|
certain regions of the kernel's memory space as read-only. If kgdb
|
|
supports it for the architecture you are using, you can use hardware
|
|
breakpoints if you desire to run with the ``CONFIG_STRICT_KERNEL_RWX``
|
|
option turned on, else you need to turn off this option.
|
|
|
|
Next you should choose one of more I/O drivers to interconnect debugging
|
|
host and debugged target. Early boot debugging requires a KGDB I/O
|
|
driver that supports early debugging and the driver must be built into
|
|
the kernel directly. Kgdb I/O driver configuration takes place via
|
|
kernel or module parameters which you can learn more about in the in the
|
|
section that describes the parameter kgdboc.
|
|
|
|
Here is an example set of ``.config`` symbols to enable or disable for kgdb::
|
|
|
|
# CONFIG_STRICT_KERNEL_RWX is not set
|
|
CONFIG_FRAME_POINTER=y
|
|
CONFIG_KGDB=y
|
|
CONFIG_KGDB_SERIAL_CONSOLE=y
|
|
|
|
Kernel config options for kdb
|
|
-----------------------------
|
|
|
|
Kdb is quite a bit more complex than the simple gdbstub sitting on top
|
|
of the kernel's debug core. Kdb must implement a shell, and also adds
|
|
some helper functions in other parts of the kernel, responsible for
|
|
printing out interesting data such as what you would see if you ran
|
|
``lsmod``, or ``ps``. In order to build kdb into the kernel you follow the
|
|
same steps as you would for kgdb.
|
|
|
|
The main config option for kdb is ``CONFIG_KGDB_KDB`` which is called
|
|
:menuselection:`KGDB_KDB: include kdb frontend for kgdb` in the config menu.
|
|
In theory you would have already also selected an I/O driver such as the
|
|
``CONFIG_KGDB_SERIAL_CONSOLE`` interface if you plan on using kdb on a
|
|
serial port, when you were configuring kgdb.
|
|
|
|
If you want to use a PS/2-style keyboard with kdb, you would select
|
|
``CONFIG_KDB_KEYBOARD`` which is called :menuselection:`KGDB_KDB: keyboard as
|
|
input device` in the config menu. The ``CONFIG_KDB_KEYBOARD`` option is not
|
|
used for anything in the gdb interface to kgdb. The ``CONFIG_KDB_KEYBOARD``
|
|
option only works with kdb.
|
|
|
|
Here is an example set of ``.config`` symbols to enable/disable kdb::
|
|
|
|
# CONFIG_STRICT_KERNEL_RWX is not set
|
|
CONFIG_FRAME_POINTER=y
|
|
CONFIG_KGDB=y
|
|
CONFIG_KGDB_SERIAL_CONSOLE=y
|
|
CONFIG_KGDB_KDB=y
|
|
CONFIG_KDB_KEYBOARD=y
|
|
|
|
Kernel Debugger Boot Arguments
|
|
==============================
|
|
|
|
This section describes the various runtime kernel parameters that affect
|
|
the configuration of the kernel debugger. The following chapter covers
|
|
using kdb and kgdb as well as providing some examples of the
|
|
configuration parameters.
|
|
|
|
Kernel parameter: kgdboc
|
|
------------------------
|
|
|
|
The kgdboc driver was originally an abbreviation meant to stand for
|
|
"kgdb over console". Today it is the primary mechanism to configure how
|
|
to communicate from gdb to kgdb as well as the devices you want to use
|
|
to interact with the kdb shell.
|
|
|
|
For kgdb/gdb, kgdboc is designed to work with a single serial port. It
|
|
is intended to cover the circumstance where you want to use a serial
|
|
console as your primary console as well as using it to perform kernel
|
|
debugging. It is also possible to use kgdb on a serial port which is not
|
|
designated as a system console. Kgdboc may be configured as a kernel
|
|
built-in or a kernel loadable module. You can only make use of
|
|
``kgdbwait`` and early debugging if you build kgdboc into the kernel as
|
|
a built-in.
|
|
|
|
Optionally you can elect to activate kms (Kernel Mode Setting)
|
|
integration. When you use kms with kgdboc and you have a video driver
|
|
that has atomic mode setting hooks, it is possible to enter the debugger
|
|
on the graphics console. When the kernel execution is resumed, the
|
|
previous graphics mode will be restored. This integration can serve as a
|
|
useful tool to aid in diagnosing crashes or doing analysis of memory
|
|
with kdb while allowing the full graphics console applications to run.
|
|
|
|
kgdboc arguments
|
|
~~~~~~~~~~~~~~~~
|
|
|
|
Usage::
|
|
|
|
kgdboc=[kms][[,]kbd][[,]serial_device][,baud]
|
|
|
|
The order listed above must be observed if you use any of the optional
|
|
configurations together.
|
|
|
|
Abbreviations:
|
|
|
|
- kms = Kernel Mode Setting
|
|
|
|
- kbd = Keyboard
|
|
|
|
You can configure kgdboc to use the keyboard, and/or a serial device
|
|
depending on if you are using kdb and/or kgdb, in one of the following
|
|
scenarios. The order listed above must be observed if you use any of the
|
|
optional configurations together. Using kms + only gdb is generally not
|
|
a useful combination.
|
|
|
|
Using loadable module or built-in
|
|
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
1. As a kernel built-in:
|
|
|
|
Use the kernel boot argument::
|
|
|
|
kgdboc=<tty-device>,[baud]
|
|
|
|
2. As a kernel loadable module:
|
|
|
|
Use the command::
|
|
|
|
modprobe kgdboc kgdboc=<tty-device>,[baud]
|
|
|
|
Here are two examples of how you might format the kgdboc string. The
|
|
first is for an x86 target using the first serial port. The second
|
|
example is for the ARM Versatile AB using the second serial port.
|
|
|
|
1. ``kgdboc=ttyS0,115200``
|
|
|
|
2. ``kgdboc=ttyAMA1,115200``
|
|
|
|
Configure kgdboc at runtime with sysfs
|
|
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
At run time you can enable or disable kgdboc by echoing a parameters
|
|
into the sysfs. Here are two examples:
|
|
|
|
1. Enable kgdboc on ttyS0::
|
|
|
|
echo ttyS0 > /sys/module/kgdboc/parameters/kgdboc
|
|
|
|
2. Disable kgdboc::
|
|
|
|
echo "" > /sys/module/kgdboc/parameters/kgdboc
|
|
|
|
.. note::
|
|
|
|
You do not need to specify the baud if you are configuring the
|
|
console on tty which is already configured or open.
|
|
|
|
More examples
|
|
^^^^^^^^^^^^^
|
|
|
|
You can configure kgdboc to use the keyboard, and/or a serial device
|
|
depending on if you are using kdb and/or kgdb, in one of the following
|
|
scenarios.
|
|
|
|
1. kdb and kgdb over only a serial port::
|
|
|
|
kgdboc=<serial_device>[,baud]
|
|
|
|
Example::
|
|
|
|
kgdboc=ttyS0,115200
|
|
|
|
2. kdb and kgdb with keyboard and a serial port::
|
|
|
|
kgdboc=kbd,<serial_device>[,baud]
|
|
|
|
Example::
|
|
|
|
kgdboc=kbd,ttyS0,115200
|
|
|
|
3. kdb with a keyboard::
|
|
|
|
kgdboc=kbd
|
|
|
|
4. kdb with kernel mode setting::
|
|
|
|
kgdboc=kms,kbd
|
|
|
|
5. kdb with kernel mode setting and kgdb over a serial port::
|
|
|
|
kgdboc=kms,kbd,ttyS0,115200
|
|
|
|
.. note::
|
|
|
|
Kgdboc does not support interrupting the target via the gdb remote
|
|
protocol. You must manually send a :kbd:`SysRq-G` unless you have a proxy
|
|
that splits console output to a terminal program. A console proxy has a
|
|
separate TCP port for the debugger and a separate TCP port for the
|
|
"human" console. The proxy can take care of sending the :kbd:`SysRq-G`
|
|
for you.
|
|
|
|
When using kgdboc with no debugger proxy, you can end up connecting the
|
|
debugger at one of two entry points. If an exception occurs after you
|
|
have loaded kgdboc, a message should print on the console stating it is
|
|
waiting for the debugger. In this case you disconnect your terminal
|
|
program and then connect the debugger in its place. If you want to
|
|
interrupt the target system and forcibly enter a debug session you have
|
|
to issue a :kbd:`Sysrq` sequence and then type the letter :kbd:`g`. Then you
|
|
disconnect the terminal session and connect gdb. Your options if you
|
|
don't like this are to hack gdb to send the :kbd:`SysRq-G` for you as well as
|
|
on the initial connect, or to use a debugger proxy that allows an
|
|
unmodified gdb to do the debugging.
|
|
|
|
Kernel parameter: ``kgdbwait``
|
|
------------------------------
|
|
|
|
The Kernel command line option ``kgdbwait`` makes kgdb wait for a
|
|
debugger connection during booting of a kernel. You can only use this
|
|
option if you compiled a kgdb I/O driver into the kernel and you
|
|
specified the I/O driver configuration as a kernel command line option.
|
|
The kgdbwait parameter should always follow the configuration parameter
|
|
for the kgdb I/O driver in the kernel command line else the I/O driver
|
|
will not be configured prior to asking the kernel to use it to wait.
|
|
|
|
The kernel will stop and wait as early as the I/O driver and
|
|
architecture allows when you use this option. If you build the kgdb I/O
|
|
driver as a loadable kernel module kgdbwait will not do anything.
|
|
|
|
Kernel parameter: ``kgdbcon``
|
|
-----------------------------
|
|
|
|
The ``kgdbcon`` feature allows you to see :c:func:`printk` messages inside gdb
|
|
while gdb is connected to the kernel. Kdb does not make use of the kgdbcon
|
|
feature.
|
|
|
|
Kgdb supports using the gdb serial protocol to send console messages to
|
|
the debugger when the debugger is connected and running. There are two
|
|
ways to activate this feature.
|
|
|
|
1. Activate with the kernel command line option::
|
|
|
|
kgdbcon
|
|
|
|
2. Use sysfs before configuring an I/O driver::
|
|
|
|
echo 1 > /sys/module/kgdb/parameters/kgdb_use_con
|
|
|
|
.. note::
|
|
|
|
If you do this after you configure the kgdb I/O driver, the
|
|
setting will not take effect until the next point the I/O is
|
|
reconfigured.
|
|
|
|
.. important::
|
|
|
|
You cannot use kgdboc + kgdbcon on a tty that is an
|
|
active system console. An example of incorrect usage is::
|
|
|
|
console=ttyS0,115200 kgdboc=ttyS0 kgdbcon
|
|
|
|
It is possible to use this option with kgdboc on a tty that is not a
|
|
system console.
|
|
|
|
Run time parameter: ``kgdbreboot``
|
|
----------------------------------
|
|
|
|
The kgdbreboot feature allows you to change how the debugger deals with
|
|
the reboot notification. You have 3 choices for the behavior. The
|
|
default behavior is always set to 0.
|
|
|
|
.. tabularcolumns:: |p{0.4cm}|p{11.5cm}|p{5.6cm}|
|
|
|
|
.. flat-table::
|
|
:widths: 1 10 8
|
|
|
|
* - 1
|
|
- ``echo -1 > /sys/module/debug_core/parameters/kgdbreboot``
|
|
- Ignore the reboot notification entirely.
|
|
|
|
* - 2
|
|
- ``echo 0 > /sys/module/debug_core/parameters/kgdbreboot``
|
|
- Send the detach message to any attached debugger client.
|
|
|
|
* - 3
|
|
- ``echo 1 > /sys/module/debug_core/parameters/kgdbreboot``
|
|
- Enter the debugger on reboot notify.
|
|
|
|
Using kdb
|
|
=========
|
|
|
|
Quick start for kdb on a serial port
|
|
------------------------------------
|
|
|
|
This is a quick example of how to use kdb.
|
|
|
|
1. Configure kgdboc at boot using kernel parameters::
|
|
|
|
console=ttyS0,115200 kgdboc=ttyS0,115200
|
|
|
|
OR
|
|
|
|
Configure kgdboc after the kernel has booted; assuming you are using
|
|
a serial port console::
|
|
|
|
echo ttyS0 > /sys/module/kgdboc/parameters/kgdboc
|
|
|
|
2. Enter the kernel debugger manually or by waiting for an oops or
|
|
fault. There are several ways you can enter the kernel debugger
|
|
manually; all involve using the :kbd:`SysRq-G`, which means you must have
|
|
enabled ``CONFIG_MAGIC_SysRq=y`` in your kernel config.
|
|
|
|
- When logged in as root or with a super user session you can run::
|
|
|
|
echo g > /proc/sysrq-trigger
|
|
|
|
- Example using minicom 2.2
|
|
|
|
Press: :kbd:`CTRL-A` :kbd:`f` :kbd:`g`
|
|
|
|
- When you have telneted to a terminal server that supports sending
|
|
a remote break
|
|
|
|
Press: :kbd:`CTRL-]`
|
|
|
|
Type in: ``send break``
|
|
|
|
Press: :kbd:`Enter` :kbd:`g`
|
|
|
|
3. From the kdb prompt you can run the ``help`` command to see a complete
|
|
list of the commands that are available.
|
|
|
|
Some useful commands in kdb include:
|
|
|
|
=========== =================================================================
|
|
``lsmod`` Shows where kernel modules are loaded
|
|
``ps`` Displays only the active processes
|
|
``ps A`` Shows all the processes
|
|
``summary`` Shows kernel version info and memory usage
|
|
``bt`` Get a backtrace of the current process using :c:func:`dump_stack`
|
|
``dmesg`` View the kernel syslog buffer
|
|
``go`` Continue the system
|
|
=========== =================================================================
|
|
|
|
4. When you are done using kdb you need to consider rebooting the system
|
|
or using the ``go`` command to resuming normal kernel execution. If you
|
|
have paused the kernel for a lengthy period of time, applications
|
|
that rely on timely networking or anything to do with real wall clock
|
|
time could be adversely affected, so you should take this into
|
|
consideration when using the kernel debugger.
|
|
|
|
Quick start for kdb using a keyboard connected console
|
|
------------------------------------------------------
|
|
|
|
This is a quick example of how to use kdb with a keyboard.
|
|
|
|
1. Configure kgdboc at boot using kernel parameters::
|
|
|
|
kgdboc=kbd
|
|
|
|
OR
|
|
|
|
Configure kgdboc after the kernel has booted::
|
|
|
|
echo kbd > /sys/module/kgdboc/parameters/kgdboc
|
|
|
|
2. Enter the kernel debugger manually or by waiting for an oops or
|
|
fault. There are several ways you can enter the kernel debugger
|
|
manually; all involve using the :kbd:`SysRq-G`, which means you must have
|
|
enabled ``CONFIG_MAGIC_SysRq=y`` in your kernel config.
|
|
|
|
- When logged in as root or with a super user session you can run::
|
|
|
|
echo g > /proc/sysrq-trigger
|
|
|
|
- Example using a laptop keyboard:
|
|
|
|
Press and hold down: :kbd:`Alt`
|
|
|
|
Press and hold down: :kbd:`Fn`
|
|
|
|
Press and release the key with the label: :kbd:`SysRq`
|
|
|
|
Release: :kbd:`Fn`
|
|
|
|
Press and release: :kbd:`g`
|
|
|
|
Release: :kbd:`Alt`
|
|
|
|
- Example using a PS/2 101-key keyboard
|
|
|
|
Press and hold down: :kbd:`Alt`
|
|
|
|
Press and release the key with the label: :kbd:`SysRq`
|
|
|
|
Press and release: :kbd:`g`
|
|
|
|
Release: :kbd:`Alt`
|
|
|
|
3. Now type in a kdb command such as ``help``, ``dmesg``, ``bt`` or ``go`` to
|
|
continue kernel execution.
|
|
|
|
Using kgdb / gdb
|
|
================
|
|
|
|
In order to use kgdb you must activate it by passing configuration
|
|
information to one of the kgdb I/O drivers. If you do not pass any
|
|
configuration information kgdb will not do anything at all. Kgdb will
|
|
only actively hook up to the kernel trap hooks if a kgdb I/O driver is
|
|
loaded and configured. If you unconfigure a kgdb I/O driver, kgdb will
|
|
unregister all the kernel hook points.
|
|
|
|
All kgdb I/O drivers can be reconfigured at run time, if
|
|
``CONFIG_SYSFS`` and ``CONFIG_MODULES`` are enabled, by echo'ing a new
|
|
config string to ``/sys/module/<driver>/parameter/<option>``. The driver
|
|
can be unconfigured by passing an empty string. You cannot change the
|
|
configuration while the debugger is attached. Make sure to detach the
|
|
debugger with the ``detach`` command prior to trying to unconfigure a
|
|
kgdb I/O driver.
|
|
|
|
Connecting with gdb to a serial port
|
|
------------------------------------
|
|
|
|
1. Configure kgdboc
|
|
|
|
Configure kgdboc at boot using kernel parameters::
|
|
|
|
kgdboc=ttyS0,115200
|
|
|
|
OR
|
|
|
|
Configure kgdboc after the kernel has booted::
|
|
|
|
echo ttyS0 > /sys/module/kgdboc/parameters/kgdboc
|
|
|
|
2. Stop kernel execution (break into the debugger)
|
|
|
|
In order to connect to gdb via kgdboc, the kernel must first be
|
|
stopped. There are several ways to stop the kernel which include
|
|
using kgdbwait as a boot argument, via a :kbd:`SysRq-G`, or running the
|
|
kernel until it takes an exception where it waits for the debugger to
|
|
attach.
|
|
|
|
- When logged in as root or with a super user session you can run::
|
|
|
|
echo g > /proc/sysrq-trigger
|
|
|
|
- Example using minicom 2.2
|
|
|
|
Press: :kbd:`CTRL-A` :kbd:`f` :kbd:`g`
|
|
|
|
- When you have telneted to a terminal server that supports sending
|
|
a remote break
|
|
|
|
Press: :kbd:`CTRL-]`
|
|
|
|
Type in: ``send break``
|
|
|
|
Press: :kbd:`Enter` :kbd:`g`
|
|
|
|
3. Connect from gdb
|
|
|
|
Example (using a directly connected port)::
|
|
|
|
% gdb ./vmlinux
|
|
(gdb) set remotebaud 115200
|
|
(gdb) target remote /dev/ttyS0
|
|
|
|
|
|
Example (kgdb to a terminal server on TCP port 2012)::
|
|
|
|
% gdb ./vmlinux
|
|
(gdb) target remote 192.168.2.2:2012
|
|
|
|
|
|
Once connected, you can debug a kernel the way you would debug an
|
|
application program.
|
|
|
|
If you are having problems connecting or something is going seriously
|
|
wrong while debugging, it will most often be the case that you want
|
|
to enable gdb to be verbose about its target communications. You do
|
|
this prior to issuing the ``target remote`` command by typing in::
|
|
|
|
set debug remote 1
|
|
|
|
Remember if you continue in gdb, and need to "break in" again, you need
|
|
to issue an other :kbd:`SysRq-G`. It is easy to create a simple entry point by
|
|
putting a breakpoint at ``sys_sync`` and then you can run ``sync`` from a
|
|
shell or script to break into the debugger.
|
|
|
|
kgdb and kdb interoperability
|
|
=============================
|
|
|
|
It is possible to transition between kdb and kgdb dynamically. The debug
|
|
core will remember which you used the last time and automatically start
|
|
in the same mode.
|
|
|
|
Switching between kdb and kgdb
|
|
------------------------------
|
|
|
|
Switching from kgdb to kdb
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
There are two ways to switch from kgdb to kdb: you can use gdb to issue
|
|
a maintenance packet, or you can blindly type the command ``$3#33``.
|
|
Whenever the kernel debugger stops in kgdb mode it will print the
|
|
message ``KGDB or $3#33 for KDB``. It is important to note that you have
|
|
to type the sequence correctly in one pass. You cannot type a backspace
|
|
or delete because kgdb will interpret that as part of the debug stream.
|
|
|
|
1. Change from kgdb to kdb by blindly typing::
|
|
|
|
$3#33
|
|
|
|
2. Change from kgdb to kdb with gdb::
|
|
|
|
maintenance packet 3
|
|
|
|
.. note::
|
|
|
|
Now you must kill gdb. Typically you press :kbd:`CTRL-Z` and issue
|
|
the command::
|
|
|
|
kill -9 %
|
|
|
|
Change from kdb to kgdb
|
|
~~~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
There are two ways you can change from kdb to kgdb. You can manually
|
|
enter kgdb mode by issuing the kgdb command from the kdb shell prompt,
|
|
or you can connect gdb while the kdb shell prompt is active. The kdb
|
|
shell looks for the typical first commands that gdb would issue with the
|
|
gdb remote protocol and if it sees one of those commands it
|
|
automatically changes into kgdb mode.
|
|
|
|
1. From kdb issue the command::
|
|
|
|
kgdb
|
|
|
|
Now disconnect your terminal program and connect gdb in its place
|
|
|
|
2. At the kdb prompt, disconnect the terminal program and connect gdb in
|
|
its place.
|
|
|
|
Running kdb commands from gdb
|
|
-----------------------------
|
|
|
|
It is possible to run a limited set of kdb commands from gdb, using the
|
|
gdb monitor command. You don't want to execute any of the run control or
|
|
breakpoint operations, because it can disrupt the state of the kernel
|
|
debugger. You should be using gdb for breakpoints and run control
|
|
operations if you have gdb connected. The more useful commands to run
|
|
are things like lsmod, dmesg, ps or possibly some of the memory
|
|
information commands. To see all the kdb commands you can run
|
|
``monitor help``.
|
|
|
|
Example::
|
|
|
|
(gdb) monitor ps
|
|
1 idle process (state I) and
|
|
27 sleeping system daemon (state M) processes suppressed,
|
|
use 'ps A' to see all.
|
|
Task Addr Pid Parent [*] cpu State Thread Command
|
|
|
|
0xc78291d0 1 0 0 0 S 0xc7829404 init
|
|
0xc7954150 942 1 0 0 S 0xc7954384 dropbear
|
|
0xc78789c0 944 1 0 0 S 0xc7878bf4 sh
|
|
(gdb)
|
|
|
|
kgdb Test Suite
|
|
===============
|
|
|
|
When kgdb is enabled in the kernel config you can also elect to enable
|
|
the config parameter ``KGDB_TESTS``. Turning this on will enable a special
|
|
kgdb I/O module which is designed to test the kgdb internal functions.
|
|
|
|
The kgdb tests are mainly intended for developers to test the kgdb
|
|
internals as well as a tool for developing a new kgdb architecture
|
|
specific implementation. These tests are not really for end users of the
|
|
Linux kernel. The primary source of documentation would be to look in
|
|
the ``drivers/misc/kgdbts.c`` file.
|
|
|
|
The kgdb test suite can also be configured at compile time to run the
|
|
core set of tests by setting the kernel config parameter
|
|
``KGDB_TESTS_ON_BOOT``. This particular option is aimed at automated
|
|
regression testing and does not require modifying the kernel boot config
|
|
arguments. If this is turned on, the kgdb test suite can be disabled by
|
|
specifying ``kgdbts=`` as a kernel boot argument.
|
|
|
|
Kernel Debugger Internals
|
|
=========================
|
|
|
|
Architecture Specifics
|
|
----------------------
|
|
|
|
The kernel debugger is organized into a number of components:
|
|
|
|
1. The debug core
|
|
|
|
The debug core is found in ``kernel/debugger/debug_core.c``. It
|
|
contains:
|
|
|
|
- A generic OS exception handler which includes sync'ing the
|
|
processors into a stopped state on an multi-CPU system.
|
|
|
|
- The API to talk to the kgdb I/O drivers
|
|
|
|
- The API to make calls to the arch-specific kgdb implementation
|
|
|
|
- The logic to perform safe memory reads and writes to memory while
|
|
using the debugger
|
|
|
|
- A full implementation for software breakpoints unless overridden
|
|
by the arch
|
|
|
|
- The API to invoke either the kdb or kgdb frontend to the debug
|
|
core.
|
|
|
|
- The structures and callback API for atomic kernel mode setting.
|
|
|
|
.. note:: kgdboc is where the kms callbacks are invoked.
|
|
|
|
2. kgdb arch-specific implementation
|
|
|
|
This implementation is generally found in ``arch/*/kernel/kgdb.c``. As
|
|
an example, ``arch/x86/kernel/kgdb.c`` contains the specifics to
|
|
implement HW breakpoint as well as the initialization to dynamically
|
|
register and unregister for the trap handlers on this architecture.
|
|
The arch-specific portion implements:
|
|
|
|
- contains an arch-specific trap catcher which invokes
|
|
:c:func:`kgdb_handle_exception` to start kgdb about doing its work
|
|
|
|
- translation to and from gdb specific packet format to :c:type:`pt_regs`
|
|
|
|
- Registration and unregistration of architecture specific trap
|
|
hooks
|
|
|
|
- Any special exception handling and cleanup
|
|
|
|
- NMI exception handling and cleanup
|
|
|
|
- (optional) HW breakpoints
|
|
|
|
3. gdbstub frontend (aka kgdb)
|
|
|
|
The gdbstub is located in ``kernel/debug/gdbstub.c``. It contains:
|
|
|
|
- All the logic to implement the gdb serial protocol
|
|
|
|
4. kdb frontend
|
|
|
|
The kdb debugger shell is broken down into a number of components.
|
|
The kdb core is located in kernel/debug/kdb. There are a number of
|
|
helper functions in some of the other kernel components to make it
|
|
possible for kdb to examine and report information about the kernel
|
|
without taking locks that could cause a kernel deadlock. The kdb core
|
|
contains implements the following functionality.
|
|
|
|
- A simple shell
|
|
|
|
- The kdb core command set
|
|
|
|
- A registration API to register additional kdb shell commands.
|
|
|
|
- A good example of a self-contained kdb module is the ``ftdump``
|
|
command for dumping the ftrace buffer. See:
|
|
``kernel/trace/trace_kdb.c``
|
|
|
|
- For an example of how to dynamically register a new kdb command
|
|
you can build the kdb_hello.ko kernel module from
|
|
``samples/kdb/kdb_hello.c``. To build this example you can set
|
|
``CONFIG_SAMPLES=y`` and ``CONFIG_SAMPLE_KDB=m`` in your kernel
|
|
config. Later run ``modprobe kdb_hello`` and the next time you
|
|
enter the kdb shell, you can run the ``hello`` command.
|
|
|
|
- The implementation for :c:func:`kdb_printf` which emits messages directly
|
|
to I/O drivers, bypassing the kernel log.
|
|
|
|
- SW / HW breakpoint management for the kdb shell
|
|
|
|
5. kgdb I/O driver
|
|
|
|
Each kgdb I/O driver has to provide an implementation for the
|
|
following:
|
|
|
|
- configuration via built-in or module
|
|
|
|
- dynamic configuration and kgdb hook registration calls
|
|
|
|
- read and write character interface
|
|
|
|
- A cleanup handler for unconfiguring from the kgdb core
|
|
|
|
- (optional) Early debug methodology
|
|
|
|
Any given kgdb I/O driver has to operate very closely with the
|
|
hardware and must do it in such a way that does not enable interrupts
|
|
or change other parts of the system context without completely
|
|
restoring them. The kgdb core will repeatedly "poll" a kgdb I/O
|
|
driver for characters when it needs input. The I/O driver is expected
|
|
to return immediately if there is no data available. Doing so allows
|
|
for the future possibility to touch watchdog hardware in such a way
|
|
as to have a target system not reset when these are enabled.
|
|
|
|
If you are intent on adding kgdb architecture specific support for a new
|
|
architecture, the architecture should define ``HAVE_ARCH_KGDB`` in the
|
|
architecture specific Kconfig file. This will enable kgdb for the
|
|
architecture, and at that point you must create an architecture specific
|
|
kgdb implementation.
|
|
|
|
There are a few flags which must be set on every architecture in their
|
|
``asm/kgdb.h`` file. These are:
|
|
|
|
- ``NUMREGBYTES``:
|
|
The size in bytes of all of the registers, so that we
|
|
can ensure they will all fit into a packet.
|
|
|
|
- ``BUFMAX``:
|
|
The size in bytes of the buffer GDB will read into. This must
|
|
be larger than NUMREGBYTES.
|
|
|
|
- ``CACHE_FLUSH_IS_SAFE``:
|
|
Set to 1 if it is always safe to call
|
|
flush_cache_range or flush_icache_range. On some architectures,
|
|
these functions may not be safe to call on SMP since we keep other
|
|
CPUs in a holding pattern.
|
|
|
|
There are also the following functions for the common backend, found in
|
|
``kernel/kgdb.c``, that must be supplied by the architecture-specific
|
|
backend unless marked as (optional), in which case a default function
|
|
maybe used if the architecture does not need to provide a specific
|
|
implementation.
|
|
|
|
.. kernel-doc:: include/linux/kgdb.h
|
|
:internal:
|
|
|
|
kgdboc internals
|
|
----------------
|
|
|
|
kgdboc and uarts
|
|
~~~~~~~~~~~~~~~~
|
|
|
|
The kgdboc driver is actually a very thin driver that relies on the
|
|
underlying low level to the hardware driver having "polling hooks" to
|
|
which the tty driver is attached. In the initial implementation of
|
|
kgdboc the serial_core was changed to expose a low level UART hook for
|
|
doing polled mode reading and writing of a single character while in an
|
|
atomic context. When kgdb makes an I/O request to the debugger, kgdboc
|
|
invokes a callback in the serial core which in turn uses the callback in
|
|
the UART driver.
|
|
|
|
When using kgdboc with a UART, the UART driver must implement two
|
|
callbacks in the :c:type:`struct uart_ops <uart_ops>`.
|
|
Example from ``drivers/8250.c``::
|
|
|
|
|
|
#ifdef CONFIG_CONSOLE_POLL
|
|
.poll_get_char = serial8250_get_poll_char,
|
|
.poll_put_char = serial8250_put_poll_char,
|
|
#endif
|
|
|
|
|
|
Any implementation specifics around creating a polling driver use the
|
|
``#ifdef CONFIG_CONSOLE_POLL``, as shown above. Keep in mind that
|
|
polling hooks have to be implemented in such a way that they can be
|
|
called from an atomic context and have to restore the state of the UART
|
|
chip on return such that the system can return to normal when the
|
|
debugger detaches. You need to be very careful with any kind of lock you
|
|
consider, because failing here is most likely going to mean pressing the
|
|
reset button.
|
|
|
|
kgdboc and keyboards
|
|
~~~~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
The kgdboc driver contains logic to configure communications with an
|
|
attached keyboard. The keyboard infrastructure is only compiled into the
|
|
kernel when ``CONFIG_KDB_KEYBOARD=y`` is set in the kernel configuration.
|
|
|
|
The core polled keyboard driver driver for PS/2 type keyboards is in
|
|
``drivers/char/kdb_keyboard.c``. This driver is hooked into the debug core
|
|
when kgdboc populates the callback in the array called
|
|
:c:type:`kdb_poll_funcs[]`. The :c:func:`kdb_get_kbd_char` is the top-level
|
|
function which polls hardware for single character input.
|
|
|
|
kgdboc and kms
|
|
~~~~~~~~~~~~~~~~~~
|
|
|
|
The kgdboc driver contains logic to request the graphics display to
|
|
switch to a text context when you are using ``kgdboc=kms,kbd``, provided
|
|
that you have a video driver which has a frame buffer console and atomic
|
|
kernel mode setting support.
|
|
|
|
Every time the kernel debugger is entered it calls
|
|
:c:func:`kgdboc_pre_exp_handler` which in turn calls :c:func:`con_debug_enter`
|
|
in the virtual console layer. On resuming kernel execution, the kernel
|
|
debugger calls :c:func:`kgdboc_post_exp_handler` which in turn calls
|
|
:c:func:`con_debug_leave`.
|
|
|
|
Any video driver that wants to be compatible with the kernel debugger
|
|
and the atomic kms callbacks must implement the ``mode_set_base_atomic``,
|
|
``fb_debug_enter`` and ``fb_debug_leave operations``. For the
|
|
``fb_debug_enter`` and ``fb_debug_leave`` the option exists to use the
|
|
generic drm fb helper functions or implement something custom for the
|
|
hardware. The following example shows the initialization of the
|
|
.mode_set_base_atomic operation in
|
|
drivers/gpu/drm/i915/intel_display.c::
|
|
|
|
|
|
static const struct drm_crtc_helper_funcs intel_helper_funcs = {
|
|
[...]
|
|
.mode_set_base_atomic = intel_pipe_set_base_atomic,
|
|
[...]
|
|
};
|
|
|
|
|
|
Here is an example of how the i915 driver initializes the
|
|
fb_debug_enter and fb_debug_leave functions to use the generic drm
|
|
helpers in ``drivers/gpu/drm/i915/intel_fb.c``::
|
|
|
|
|
|
static struct fb_ops intelfb_ops = {
|
|
[...]
|
|
.fb_debug_enter = drm_fb_helper_debug_enter,
|
|
.fb_debug_leave = drm_fb_helper_debug_leave,
|
|
[...]
|
|
};
|
|
|
|
|
|
Credits
|
|
=======
|
|
|
|
The following people have contributed to this document:
|
|
|
|
1. Amit Kale <amitkale@linsyssoft.com>
|
|
|
|
2. Tom Rini <trini@kernel.crashing.org>
|
|
|
|
In March 2008 this document was completely rewritten by:
|
|
|
|
- Jason Wessel <jason.wessel@windriver.com>
|
|
|
|
In Jan 2010 this document was updated to include kdb.
|
|
|
|
- Jason Wessel <jason.wessel@windriver.com>
|