linux-sg2042/drivers/spi/spi-ep93xx.c

977 lines
24 KiB
C

/*
* Driver for Cirrus Logic EP93xx SPI controller.
*
* Copyright (C) 2010-2011 Mika Westerberg
*
* Explicit FIFO handling code was inspired by amba-pl022 driver.
*
* Chip select support using other than built-in GPIOs by H. Hartley Sweeten.
*
* For more information about the SPI controller see documentation on Cirrus
* Logic web site:
* http://www.cirrus.com/en/pubs/manual/EP93xx_Users_Guide_UM1.pdf
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/io.h>
#include <linux/clk.h>
#include <linux/err.h>
#include <linux/delay.h>
#include <linux/device.h>
#include <linux/dmaengine.h>
#include <linux/bitops.h>
#include <linux/interrupt.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/sched.h>
#include <linux/scatterlist.h>
#include <linux/spi/spi.h>
#include <linux/platform_data/dma-ep93xx.h>
#include <linux/platform_data/spi-ep93xx.h>
#define SSPCR0 0x0000
#define SSPCR0_MODE_SHIFT 6
#define SSPCR0_SCR_SHIFT 8
#define SSPCR1 0x0004
#define SSPCR1_RIE BIT(0)
#define SSPCR1_TIE BIT(1)
#define SSPCR1_RORIE BIT(2)
#define SSPCR1_LBM BIT(3)
#define SSPCR1_SSE BIT(4)
#define SSPCR1_MS BIT(5)
#define SSPCR1_SOD BIT(6)
#define SSPDR 0x0008
#define SSPSR 0x000c
#define SSPSR_TFE BIT(0)
#define SSPSR_TNF BIT(1)
#define SSPSR_RNE BIT(2)
#define SSPSR_RFF BIT(3)
#define SSPSR_BSY BIT(4)
#define SSPCPSR 0x0010
#define SSPIIR 0x0014
#define SSPIIR_RIS BIT(0)
#define SSPIIR_TIS BIT(1)
#define SSPIIR_RORIS BIT(2)
#define SSPICR SSPIIR
/* timeout in milliseconds */
#define SPI_TIMEOUT 5
/* maximum depth of RX/TX FIFO */
#define SPI_FIFO_SIZE 8
/**
* struct ep93xx_spi - EP93xx SPI controller structure
* @pdev: pointer to platform device
* @clk: clock for the controller
* @regs_base: pointer to ioremap()'d registers
* @sspdr_phys: physical address of the SSPDR register
* @wait: wait here until given transfer is completed
* @current_msg: message that is currently processed (or %NULL if none)
* @tx: current byte in transfer to transmit
* @rx: current byte in transfer to receive
* @fifo_level: how full is FIFO (%0..%SPI_FIFO_SIZE - %1). Receiving one
* frame decreases this level and sending one frame increases it.
* @dma_rx: RX DMA channel
* @dma_tx: TX DMA channel
* @dma_rx_data: RX parameters passed to the DMA engine
* @dma_tx_data: TX parameters passed to the DMA engine
* @rx_sgt: sg table for RX transfers
* @tx_sgt: sg table for TX transfers
* @zeropage: dummy page used as RX buffer when only TX buffer is passed in by
* the client
*/
struct ep93xx_spi {
const struct platform_device *pdev;
struct clk *clk;
void __iomem *regs_base;
unsigned long sspdr_phys;
struct completion wait;
struct spi_message *current_msg;
size_t tx;
size_t rx;
size_t fifo_level;
struct dma_chan *dma_rx;
struct dma_chan *dma_tx;
struct ep93xx_dma_data dma_rx_data;
struct ep93xx_dma_data dma_tx_data;
struct sg_table rx_sgt;
struct sg_table tx_sgt;
void *zeropage;
};
/**
* struct ep93xx_spi_chip - SPI device hardware settings
* @spi: back pointer to the SPI device
* @ops: private chip operations
*/
struct ep93xx_spi_chip {
const struct spi_device *spi;
struct ep93xx_spi_chip_ops *ops;
};
/* converts bits per word to CR0.DSS value */
#define bits_per_word_to_dss(bpw) ((bpw) - 1)
static void ep93xx_spi_write_u8(const struct ep93xx_spi *espi,
u16 reg, u8 value)
{
writeb(value, espi->regs_base + reg);
}
static u8 ep93xx_spi_read_u8(const struct ep93xx_spi *spi, u16 reg)
{
return readb(spi->regs_base + reg);
}
static void ep93xx_spi_write_u16(const struct ep93xx_spi *espi,
u16 reg, u16 value)
{
writew(value, espi->regs_base + reg);
}
static u16 ep93xx_spi_read_u16(const struct ep93xx_spi *spi, u16 reg)
{
return readw(spi->regs_base + reg);
}
static int ep93xx_spi_enable(const struct ep93xx_spi *espi)
{
u8 regval;
int err;
err = clk_enable(espi->clk);
if (err)
return err;
regval = ep93xx_spi_read_u8(espi, SSPCR1);
regval |= SSPCR1_SSE;
ep93xx_spi_write_u8(espi, SSPCR1, regval);
return 0;
}
static void ep93xx_spi_disable(const struct ep93xx_spi *espi)
{
u8 regval;
regval = ep93xx_spi_read_u8(espi, SSPCR1);
regval &= ~SSPCR1_SSE;
ep93xx_spi_write_u8(espi, SSPCR1, regval);
clk_disable(espi->clk);
}
static void ep93xx_spi_enable_interrupts(const struct ep93xx_spi *espi)
{
u8 regval;
regval = ep93xx_spi_read_u8(espi, SSPCR1);
regval |= (SSPCR1_RORIE | SSPCR1_TIE | SSPCR1_RIE);
ep93xx_spi_write_u8(espi, SSPCR1, regval);
}
static void ep93xx_spi_disable_interrupts(const struct ep93xx_spi *espi)
{
u8 regval;
regval = ep93xx_spi_read_u8(espi, SSPCR1);
regval &= ~(SSPCR1_RORIE | SSPCR1_TIE | SSPCR1_RIE);
ep93xx_spi_write_u8(espi, SSPCR1, regval);
}
/**
* ep93xx_spi_calc_divisors() - calculates SPI clock divisors
* @espi: ep93xx SPI controller struct
* @rate: desired SPI output clock rate
* @div_cpsr: pointer to return the cpsr (pre-scaler) divider
* @div_scr: pointer to return the scr divider
*/
static int ep93xx_spi_calc_divisors(const struct ep93xx_spi *espi,
u32 rate, u8 *div_cpsr, u8 *div_scr)
{
struct spi_master *master = platform_get_drvdata(espi->pdev);
unsigned long spi_clk_rate = clk_get_rate(espi->clk);
int cpsr, scr;
/*
* Make sure that max value is between values supported by the
* controller. Note that minimum value is already checked in
* ep93xx_spi_transfer_one_message().
*/
rate = clamp(rate, master->min_speed_hz, master->max_speed_hz);
/*
* Calculate divisors so that we can get speed according the
* following formula:
* rate = spi_clock_rate / (cpsr * (1 + scr))
*
* cpsr must be even number and starts from 2, scr can be any number
* between 0 and 255.
*/
for (cpsr = 2; cpsr <= 254; cpsr += 2) {
for (scr = 0; scr <= 255; scr++) {
if ((spi_clk_rate / (cpsr * (scr + 1))) <= rate) {
*div_scr = (u8)scr;
*div_cpsr = (u8)cpsr;
return 0;
}
}
}
return -EINVAL;
}
static void ep93xx_spi_cs_control(struct spi_device *spi, bool control)
{
struct ep93xx_spi_chip *chip = spi_get_ctldata(spi);
int value = (spi->mode & SPI_CS_HIGH) ? control : !control;
if (chip->ops && chip->ops->cs_control)
chip->ops->cs_control(spi, value);
}
/**
* ep93xx_spi_setup() - setup an SPI device
* @spi: SPI device to setup
*
* This function sets up SPI device mode, speed etc. Can be called multiple
* times for a single device. Returns %0 in case of success, negative error in
* case of failure. When this function returns success, the device is
* deselected.
*/
static int ep93xx_spi_setup(struct spi_device *spi)
{
struct ep93xx_spi *espi = spi_master_get_devdata(spi->master);
struct ep93xx_spi_chip *chip;
chip = spi_get_ctldata(spi);
if (!chip) {
dev_dbg(&espi->pdev->dev, "initial setup for %s\n",
spi->modalias);
chip = kzalloc(sizeof(*chip), GFP_KERNEL);
if (!chip)
return -ENOMEM;
chip->spi = spi;
chip->ops = spi->controller_data;
if (chip->ops && chip->ops->setup) {
int ret = chip->ops->setup(spi);
if (ret) {
kfree(chip);
return ret;
}
}
spi_set_ctldata(spi, chip);
}
ep93xx_spi_cs_control(spi, false);
return 0;
}
/**
* ep93xx_spi_cleanup() - cleans up master controller specific state
* @spi: SPI device to cleanup
*
* This function releases master controller specific state for given @spi
* device.
*/
static void ep93xx_spi_cleanup(struct spi_device *spi)
{
struct ep93xx_spi_chip *chip;
chip = spi_get_ctldata(spi);
if (chip) {
if (chip->ops && chip->ops->cleanup)
chip->ops->cleanup(spi);
spi_set_ctldata(spi, NULL);
kfree(chip);
}
}
/**
* ep93xx_spi_chip_setup() - configures hardware according to given @chip
* @espi: ep93xx SPI controller struct
* @chip: chip specific settings
* @speed_hz: transfer speed
* @bits_per_word: transfer bits_per_word
*/
static int ep93xx_spi_chip_setup(const struct ep93xx_spi *espi,
const struct ep93xx_spi_chip *chip,
u32 speed_hz, u8 bits_per_word)
{
u8 dss = bits_per_word_to_dss(bits_per_word);
u8 div_cpsr = 0;
u8 div_scr = 0;
u16 cr0;
int err;
err = ep93xx_spi_calc_divisors(espi, speed_hz, &div_cpsr, &div_scr);
if (err)
return err;
cr0 = div_scr << SSPCR0_SCR_SHIFT;
cr0 |= (chip->spi->mode & (SPI_CPHA|SPI_CPOL)) << SSPCR0_MODE_SHIFT;
cr0 |= dss;
dev_dbg(&espi->pdev->dev, "setup: mode %d, cpsr %d, scr %d, dss %d\n",
chip->spi->mode, div_cpsr, div_scr, dss);
dev_dbg(&espi->pdev->dev, "setup: cr0 %#x\n", cr0);
ep93xx_spi_write_u8(espi, SSPCPSR, div_cpsr);
ep93xx_spi_write_u16(espi, SSPCR0, cr0);
return 0;
}
static void ep93xx_do_write(struct ep93xx_spi *espi, struct spi_transfer *t)
{
if (t->bits_per_word > 8) {
u16 tx_val = 0;
if (t->tx_buf)
tx_val = ((u16 *)t->tx_buf)[espi->tx];
ep93xx_spi_write_u16(espi, SSPDR, tx_val);
espi->tx += sizeof(tx_val);
} else {
u8 tx_val = 0;
if (t->tx_buf)
tx_val = ((u8 *)t->tx_buf)[espi->tx];
ep93xx_spi_write_u8(espi, SSPDR, tx_val);
espi->tx += sizeof(tx_val);
}
}
static void ep93xx_do_read(struct ep93xx_spi *espi, struct spi_transfer *t)
{
if (t->bits_per_word > 8) {
u16 rx_val;
rx_val = ep93xx_spi_read_u16(espi, SSPDR);
if (t->rx_buf)
((u16 *)t->rx_buf)[espi->rx] = rx_val;
espi->rx += sizeof(rx_val);
} else {
u8 rx_val;
rx_val = ep93xx_spi_read_u8(espi, SSPDR);
if (t->rx_buf)
((u8 *)t->rx_buf)[espi->rx] = rx_val;
espi->rx += sizeof(rx_val);
}
}
/**
* ep93xx_spi_read_write() - perform next RX/TX transfer
* @espi: ep93xx SPI controller struct
*
* This function transfers next bytes (or half-words) to/from RX/TX FIFOs. If
* called several times, the whole transfer will be completed. Returns
* %-EINPROGRESS when current transfer was not yet completed otherwise %0.
*
* When this function is finished, RX FIFO should be empty and TX FIFO should be
* full.
*/
static int ep93xx_spi_read_write(struct ep93xx_spi *espi)
{
struct spi_message *msg = espi->current_msg;
struct spi_transfer *t = msg->state;
/* read as long as RX FIFO has frames in it */
while ((ep93xx_spi_read_u8(espi, SSPSR) & SSPSR_RNE)) {
ep93xx_do_read(espi, t);
espi->fifo_level--;
}
/* write as long as TX FIFO has room */
while (espi->fifo_level < SPI_FIFO_SIZE && espi->tx < t->len) {
ep93xx_do_write(espi, t);
espi->fifo_level++;
}
if (espi->rx == t->len)
return 0;
return -EINPROGRESS;
}
static void ep93xx_spi_pio_transfer(struct ep93xx_spi *espi)
{
/*
* Now everything is set up for the current transfer. We prime the TX
* FIFO, enable interrupts, and wait for the transfer to complete.
*/
if (ep93xx_spi_read_write(espi)) {
ep93xx_spi_enable_interrupts(espi);
wait_for_completion(&espi->wait);
}
}
/**
* ep93xx_spi_dma_prepare() - prepares a DMA transfer
* @espi: ep93xx SPI controller struct
* @dir: DMA transfer direction
*
* Function configures the DMA, maps the buffer and prepares the DMA
* descriptor. Returns a valid DMA descriptor in case of success and ERR_PTR
* in case of failure.
*/
static struct dma_async_tx_descriptor *
ep93xx_spi_dma_prepare(struct ep93xx_spi *espi, enum dma_transfer_direction dir)
{
struct spi_transfer *t = espi->current_msg->state;
struct dma_async_tx_descriptor *txd;
enum dma_slave_buswidth buswidth;
struct dma_slave_config conf;
struct scatterlist *sg;
struct sg_table *sgt;
struct dma_chan *chan;
const void *buf, *pbuf;
size_t len = t->len;
int i, ret, nents;
if (t->bits_per_word > 8)
buswidth = DMA_SLAVE_BUSWIDTH_2_BYTES;
else
buswidth = DMA_SLAVE_BUSWIDTH_1_BYTE;
memset(&conf, 0, sizeof(conf));
conf.direction = dir;
if (dir == DMA_DEV_TO_MEM) {
chan = espi->dma_rx;
buf = t->rx_buf;
sgt = &espi->rx_sgt;
conf.src_addr = espi->sspdr_phys;
conf.src_addr_width = buswidth;
} else {
chan = espi->dma_tx;
buf = t->tx_buf;
sgt = &espi->tx_sgt;
conf.dst_addr = espi->sspdr_phys;
conf.dst_addr_width = buswidth;
}
ret = dmaengine_slave_config(chan, &conf);
if (ret)
return ERR_PTR(ret);
/*
* We need to split the transfer into PAGE_SIZE'd chunks. This is
* because we are using @espi->zeropage to provide a zero RX buffer
* for the TX transfers and we have only allocated one page for that.
*
* For performance reasons we allocate a new sg_table only when
* needed. Otherwise we will re-use the current one. Eventually the
* last sg_table is released in ep93xx_spi_release_dma().
*/
nents = DIV_ROUND_UP(len, PAGE_SIZE);
if (nents != sgt->nents) {
sg_free_table(sgt);
ret = sg_alloc_table(sgt, nents, GFP_KERNEL);
if (ret)
return ERR_PTR(ret);
}
pbuf = buf;
for_each_sg(sgt->sgl, sg, sgt->nents, i) {
size_t bytes = min_t(size_t, len, PAGE_SIZE);
if (buf) {
sg_set_page(sg, virt_to_page(pbuf), bytes,
offset_in_page(pbuf));
} else {
sg_set_page(sg, virt_to_page(espi->zeropage),
bytes, 0);
}
pbuf += bytes;
len -= bytes;
}
if (WARN_ON(len)) {
dev_warn(&espi->pdev->dev, "len = %zu expected 0!\n", len);
return ERR_PTR(-EINVAL);
}
nents = dma_map_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
if (!nents)
return ERR_PTR(-ENOMEM);
txd = dmaengine_prep_slave_sg(chan, sgt->sgl, nents, dir, DMA_CTRL_ACK);
if (!txd) {
dma_unmap_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
return ERR_PTR(-ENOMEM);
}
return txd;
}
/**
* ep93xx_spi_dma_finish() - finishes with a DMA transfer
* @espi: ep93xx SPI controller struct
* @dir: DMA transfer direction
*
* Function finishes with the DMA transfer. After this, the DMA buffer is
* unmapped.
*/
static void ep93xx_spi_dma_finish(struct ep93xx_spi *espi,
enum dma_transfer_direction dir)
{
struct dma_chan *chan;
struct sg_table *sgt;
if (dir == DMA_DEV_TO_MEM) {
chan = espi->dma_rx;
sgt = &espi->rx_sgt;
} else {
chan = espi->dma_tx;
sgt = &espi->tx_sgt;
}
dma_unmap_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
}
static void ep93xx_spi_dma_callback(void *callback_param)
{
complete(callback_param);
}
static void ep93xx_spi_dma_transfer(struct ep93xx_spi *espi)
{
struct spi_message *msg = espi->current_msg;
struct dma_async_tx_descriptor *rxd, *txd;
rxd = ep93xx_spi_dma_prepare(espi, DMA_DEV_TO_MEM);
if (IS_ERR(rxd)) {
dev_err(&espi->pdev->dev, "DMA RX failed: %ld\n", PTR_ERR(rxd));
msg->status = PTR_ERR(rxd);
return;
}
txd = ep93xx_spi_dma_prepare(espi, DMA_MEM_TO_DEV);
if (IS_ERR(txd)) {
ep93xx_spi_dma_finish(espi, DMA_DEV_TO_MEM);
dev_err(&espi->pdev->dev, "DMA TX failed: %ld\n", PTR_ERR(rxd));
msg->status = PTR_ERR(txd);
return;
}
/* We are ready when RX is done */
rxd->callback = ep93xx_spi_dma_callback;
rxd->callback_param = &espi->wait;
/* Now submit both descriptors and wait while they finish */
dmaengine_submit(rxd);
dmaengine_submit(txd);
dma_async_issue_pending(espi->dma_rx);
dma_async_issue_pending(espi->dma_tx);
wait_for_completion(&espi->wait);
ep93xx_spi_dma_finish(espi, DMA_MEM_TO_DEV);
ep93xx_spi_dma_finish(espi, DMA_DEV_TO_MEM);
}
/**
* ep93xx_spi_process_transfer() - processes one SPI transfer
* @espi: ep93xx SPI controller struct
* @msg: current message
* @t: transfer to process
*
* This function processes one SPI transfer given in @t. Function waits until
* transfer is complete (may sleep) and updates @msg->status based on whether
* transfer was successfully processed or not.
*/
static void ep93xx_spi_process_transfer(struct ep93xx_spi *espi,
struct spi_message *msg,
struct spi_transfer *t)
{
struct ep93xx_spi_chip *chip = spi_get_ctldata(msg->spi);
int err;
msg->state = t;
err = ep93xx_spi_chip_setup(espi, chip, t->speed_hz, t->bits_per_word);
if (err) {
dev_err(&espi->pdev->dev,
"failed to setup chip for transfer\n");
msg->status = err;
return;
}
espi->rx = 0;
espi->tx = 0;
/*
* There is no point of setting up DMA for the transfers which will
* fit into the FIFO and can be transferred with a single interrupt.
* So in these cases we will be using PIO and don't bother for DMA.
*/
if (espi->dma_rx && t->len > SPI_FIFO_SIZE)
ep93xx_spi_dma_transfer(espi);
else
ep93xx_spi_pio_transfer(espi);
/*
* In case of error during transmit, we bail out from processing
* the message.
*/
if (msg->status)
return;
msg->actual_length += t->len;
/*
* After this transfer is finished, perform any possible
* post-transfer actions requested by the protocol driver.
*/
if (t->delay_usecs) {
set_current_state(TASK_UNINTERRUPTIBLE);
schedule_timeout(usecs_to_jiffies(t->delay_usecs));
}
if (t->cs_change) {
if (!list_is_last(&t->transfer_list, &msg->transfers)) {
/*
* In case protocol driver is asking us to drop the
* chipselect briefly, we let the scheduler to handle
* any "delay" here.
*/
ep93xx_spi_cs_control(msg->spi, false);
cond_resched();
ep93xx_spi_cs_control(msg->spi, true);
}
}
}
/*
* ep93xx_spi_process_message() - process one SPI message
* @espi: ep93xx SPI controller struct
* @msg: message to process
*
* This function processes a single SPI message. We go through all transfers in
* the message and pass them to ep93xx_spi_process_transfer(). Chipselect is
* asserted during the whole message (unless per transfer cs_change is set).
*
* @msg->status contains %0 in case of success or negative error code in case of
* failure.
*/
static void ep93xx_spi_process_message(struct ep93xx_spi *espi,
struct spi_message *msg)
{
unsigned long timeout;
struct spi_transfer *t;
int err;
/*
* Enable the SPI controller and its clock.
*/
err = ep93xx_spi_enable(espi);
if (err) {
dev_err(&espi->pdev->dev, "failed to enable SPI controller\n");
msg->status = err;
return;
}
/*
* Just to be sure: flush any data from RX FIFO.
*/
timeout = jiffies + msecs_to_jiffies(SPI_TIMEOUT);
while (ep93xx_spi_read_u16(espi, SSPSR) & SSPSR_RNE) {
if (time_after(jiffies, timeout)) {
dev_warn(&espi->pdev->dev,
"timeout while flushing RX FIFO\n");
msg->status = -ETIMEDOUT;
return;
}
ep93xx_spi_read_u16(espi, SSPDR);
}
/*
* We explicitly handle FIFO level. This way we don't have to check TX
* FIFO status using %SSPSR_TNF bit which may cause RX FIFO overruns.
*/
espi->fifo_level = 0;
/*
* Assert the chipselect.
*/
ep93xx_spi_cs_control(msg->spi, true);
list_for_each_entry(t, &msg->transfers, transfer_list) {
ep93xx_spi_process_transfer(espi, msg, t);
if (msg->status)
break;
}
/*
* Now the whole message is transferred (or failed for some reason). We
* deselect the device and disable the SPI controller.
*/
ep93xx_spi_cs_control(msg->spi, false);
ep93xx_spi_disable(espi);
}
static int ep93xx_spi_transfer_one_message(struct spi_master *master,
struct spi_message *msg)
{
struct ep93xx_spi *espi = spi_master_get_devdata(master);
msg->state = NULL;
msg->status = 0;
msg->actual_length = 0;
espi->current_msg = msg;
ep93xx_spi_process_message(espi, msg);
espi->current_msg = NULL;
spi_finalize_current_message(master);
return 0;
}
static irqreturn_t ep93xx_spi_interrupt(int irq, void *dev_id)
{
struct ep93xx_spi *espi = dev_id;
u8 irq_status = ep93xx_spi_read_u8(espi, SSPIIR);
/*
* If we got ROR (receive overrun) interrupt we know that something is
* wrong. Just abort the message.
*/
if (unlikely(irq_status & SSPIIR_RORIS)) {
/* clear the overrun interrupt */
ep93xx_spi_write_u8(espi, SSPICR, 0);
dev_warn(&espi->pdev->dev,
"receive overrun, aborting the message\n");
espi->current_msg->status = -EIO;
} else {
/*
* Interrupt is either RX (RIS) or TX (TIS). For both cases we
* simply execute next data transfer.
*/
if (ep93xx_spi_read_write(espi)) {
/*
* In normal case, there still is some processing left
* for current transfer. Let's wait for the next
* interrupt then.
*/
return IRQ_HANDLED;
}
}
/*
* Current transfer is finished, either with error or with success. In
* any case we disable interrupts and notify the worker to handle
* any post-processing of the message.
*/
ep93xx_spi_disable_interrupts(espi);
complete(&espi->wait);
return IRQ_HANDLED;
}
static bool ep93xx_spi_dma_filter(struct dma_chan *chan, void *filter_param)
{
if (ep93xx_dma_chan_is_m2p(chan))
return false;
chan->private = filter_param;
return true;
}
static int ep93xx_spi_setup_dma(struct ep93xx_spi *espi)
{
dma_cap_mask_t mask;
int ret;
espi->zeropage = (void *)get_zeroed_page(GFP_KERNEL);
if (!espi->zeropage)
return -ENOMEM;
dma_cap_zero(mask);
dma_cap_set(DMA_SLAVE, mask);
espi->dma_rx_data.port = EP93XX_DMA_SSP;
espi->dma_rx_data.direction = DMA_DEV_TO_MEM;
espi->dma_rx_data.name = "ep93xx-spi-rx";
espi->dma_rx = dma_request_channel(mask, ep93xx_spi_dma_filter,
&espi->dma_rx_data);
if (!espi->dma_rx) {
ret = -ENODEV;
goto fail_free_page;
}
espi->dma_tx_data.port = EP93XX_DMA_SSP;
espi->dma_tx_data.direction = DMA_MEM_TO_DEV;
espi->dma_tx_data.name = "ep93xx-spi-tx";
espi->dma_tx = dma_request_channel(mask, ep93xx_spi_dma_filter,
&espi->dma_tx_data);
if (!espi->dma_tx) {
ret = -ENODEV;
goto fail_release_rx;
}
return 0;
fail_release_rx:
dma_release_channel(espi->dma_rx);
espi->dma_rx = NULL;
fail_free_page:
free_page((unsigned long)espi->zeropage);
return ret;
}
static void ep93xx_spi_release_dma(struct ep93xx_spi *espi)
{
if (espi->dma_rx) {
dma_release_channel(espi->dma_rx);
sg_free_table(&espi->rx_sgt);
}
if (espi->dma_tx) {
dma_release_channel(espi->dma_tx);
sg_free_table(&espi->tx_sgt);
}
if (espi->zeropage)
free_page((unsigned long)espi->zeropage);
}
static int ep93xx_spi_probe(struct platform_device *pdev)
{
struct spi_master *master;
struct ep93xx_spi_info *info;
struct ep93xx_spi *espi;
struct resource *res;
int irq;
int error;
info = dev_get_platdata(&pdev->dev);
irq = platform_get_irq(pdev, 0);
if (irq < 0) {
dev_err(&pdev->dev, "failed to get irq resources\n");
return -EBUSY;
}
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!res) {
dev_err(&pdev->dev, "unable to get iomem resource\n");
return -ENODEV;
}
master = spi_alloc_master(&pdev->dev, sizeof(*espi));
if (!master)
return -ENOMEM;
master->setup = ep93xx_spi_setup;
master->transfer_one_message = ep93xx_spi_transfer_one_message;
master->cleanup = ep93xx_spi_cleanup;
master->bus_num = pdev->id;
master->num_chipselect = info->num_chipselect;
master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
master->bits_per_word_mask = SPI_BPW_RANGE_MASK(4, 16);
platform_set_drvdata(pdev, master);
espi = spi_master_get_devdata(master);
espi->clk = devm_clk_get(&pdev->dev, NULL);
if (IS_ERR(espi->clk)) {
dev_err(&pdev->dev, "unable to get spi clock\n");
error = PTR_ERR(espi->clk);
goto fail_release_master;
}
init_completion(&espi->wait);
/*
* Calculate maximum and minimum supported clock rates
* for the controller.
*/
master->max_speed_hz = clk_get_rate(espi->clk) / 2;
master->min_speed_hz = clk_get_rate(espi->clk) / (254 * 256);
espi->pdev = pdev;
espi->sspdr_phys = res->start + SSPDR;
espi->regs_base = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(espi->regs_base)) {
error = PTR_ERR(espi->regs_base);
goto fail_release_master;
}
error = devm_request_irq(&pdev->dev, irq, ep93xx_spi_interrupt,
0, "ep93xx-spi", espi);
if (error) {
dev_err(&pdev->dev, "failed to request irq\n");
goto fail_release_master;
}
if (info->use_dma && ep93xx_spi_setup_dma(espi))
dev_warn(&pdev->dev, "DMA setup failed. Falling back to PIO\n");
/* make sure that the hardware is disabled */
ep93xx_spi_write_u8(espi, SSPCR1, 0);
error = devm_spi_register_master(&pdev->dev, master);
if (error) {
dev_err(&pdev->dev, "failed to register SPI master\n");
goto fail_free_dma;
}
dev_info(&pdev->dev, "EP93xx SPI Controller at 0x%08lx irq %d\n",
(unsigned long)res->start, irq);
return 0;
fail_free_dma:
ep93xx_spi_release_dma(espi);
fail_release_master:
spi_master_put(master);
return error;
}
static int ep93xx_spi_remove(struct platform_device *pdev)
{
struct spi_master *master = platform_get_drvdata(pdev);
struct ep93xx_spi *espi = spi_master_get_devdata(master);
ep93xx_spi_release_dma(espi);
return 0;
}
static struct platform_driver ep93xx_spi_driver = {
.driver = {
.name = "ep93xx-spi",
},
.probe = ep93xx_spi_probe,
.remove = ep93xx_spi_remove,
};
module_platform_driver(ep93xx_spi_driver);
MODULE_DESCRIPTION("EP93xx SPI Controller driver");
MODULE_AUTHOR("Mika Westerberg <mika.westerberg@iki.fi>");
MODULE_LICENSE("GPL");
MODULE_ALIAS("platform:ep93xx-spi");