# # PINCTRL infrastructure and drivers # config PINCTRL bool menu "Pin controllers" depends on PINCTRL config PINMUX bool "Support pin multiplexing controllers" if COMPILE_TEST config PINCONF bool "Support pin configuration controllers" if COMPILE_TEST config GENERIC_PINCONF bool select PINCONF config DEBUG_PINCTRL bool "Debug PINCTRL calls" depends on DEBUG_KERNEL help Say Y here to add some extra checks and diagnostics to PINCTRL calls. config PINCTRL_ADI2 bool "ADI pin controller driver" depends on BLACKFIN select PINMUX select IRQ_DOMAIN help This is the pin controller and gpio driver for ADI BF54x, BF60x and future processors. This option is selected automatically when specific machine and arch are selected to build. config PINCTRL_AS3722 bool "Pinctrl and GPIO driver for ams AS3722 PMIC" depends on MFD_AS3722 && GPIOLIB select PINMUX select GENERIC_PINCONF help AS3722 device supports the configuration of GPIO pins for different functionality. This driver supports the pinmux, push-pull and open drain configuration for the GPIO pins of AS3722 devices. It also supports the GPIO functionality through gpiolib. config PINCTRL_BF54x def_bool y if BF54x select PINCTRL_ADI2 config PINCTRL_BF60x def_bool y if BF60x select PINCTRL_ADI2 config PINCTRL_AT91 bool "AT91 pinctrl driver" depends on OF depends on ARCH_AT91 select PINMUX select PINCONF select GPIOLIB select OF_GPIO select GPIOLIB_IRQCHIP help Say Y here to enable the at91 pinctrl driver config PINCTRL_AT91PIO4 bool "AT91 PIO4 pinctrl driver" depends on OF depends on ARCH_AT91 select PINMUX select GENERIC_PINCONF select GPIOLIB select GPIOLIB_IRQCHIP select OF_GPIO help Say Y here to enable the at91 pinctrl/gpio driver for Atmel PIO4 controller available on sama5d2 SoC. config PINCTRL_AMD bool "AMD GPIO pin control" depends on GPIOLIB select GPIOLIB_IRQCHIP select PINCONF select GENERIC_PINCONF help driver for memory mapped GPIO functionality on AMD platforms (x86 or arm).Most pins are usually muxed to some other functionality by firmware,so only a small amount is available for gpio use. Requires ACPI/FDT device enumeration code to set up a platform device. config PINCTRL_DIGICOLOR bool depends on OF && (ARCH_DIGICOLOR || COMPILE_TEST) select PINMUX select GENERIC_PINCONF config PINCTRL_LANTIQ bool depends on LANTIQ select PINMUX select PINCONF config PINCTRL_LPC18XX bool "NXP LPC18XX/43XX SCU pinctrl driver" depends on OF && (ARCH_LPC18XX || COMPILE_TEST) default ARCH_LPC18XX select PINMUX select GENERIC_PINCONF help Pinctrl driver for NXP LPC18xx/43xx System Control Unit (SCU). config PINCTRL_FALCON bool depends on SOC_FALCON depends on PINCTRL_LANTIQ config PINCTRL_MESON bool depends on OF select PINMUX select PINCONF select GENERIC_PINCONF select GPIOLIB select OF_GPIO select REGMAP_MMIO config PINCTRL_ROCKCHIP bool select PINMUX select GENERIC_PINCONF select GENERIC_IRQ_CHIP select MFD_SYSCON config PINCTRL_SINGLE tristate "One-register-per-pin type device tree based pinctrl driver" depends on OF select PINMUX select PINCONF select GENERIC_PINCONF help This selects the device tree based generic pinctrl driver. config PINCTRL_SIRF bool "CSR SiRFprimaII pin controller driver" depends on ARCH_SIRF select PINMUX select PINCONF select GENERIC_PINCONF select GPIOLIB_IRQCHIP config PINCTRL_PISTACHIO def_bool y if MACH_PISTACHIO depends on GPIOLIB select PINMUX select GENERIC_PINCONF select GPIOLIB_IRQCHIP select OF_GPIO config PINCTRL_ST bool depends on OF select PINMUX select PINCONF select GPIOLIB_IRQCHIP config PINCTRL_TZ1090 bool "Toumaz Xenif TZ1090 pin control driver" depends on SOC_TZ1090 select PINMUX select GENERIC_PINCONF config PINCTRL_TZ1090_PDC bool "Toumaz Xenif TZ1090 PDC pin control driver" depends on SOC_TZ1090 select PINMUX select PINCONF config PINCTRL_U300 bool "U300 pin controller driver" depends on ARCH_U300 select PINMUX select GENERIC_PINCONF config PINCTRL_COH901 bool "ST-Ericsson U300 COH 901 335/571 GPIO" depends on GPIOLIB && ARCH_U300 && PINCTRL_U300 select GPIOLIB_IRQCHIP help Say yes here to support GPIO interface on ST-Ericsson U300. The names of the two IP block variants supported are COH 901 335 and COH 901 571/3. They contain 3, 5 or 7 ports of 8 GPIO pins each. config PINCTRL_PALMAS bool "Pinctrl driver for the PALMAS Series MFD devices" depends on OF && MFD_PALMAS select PINMUX select GENERIC_PINCONF help Palmas device supports the configuration of pins for different functionality. This driver supports the pinmux, push-pull and open drain configuration for the Palmas series devices like TPS65913, TPS80036 etc. config PINCTRL_ZYNQ bool "Pinctrl driver for Xilinx Zynq" depends on ARCH_ZYNQ select PINMUX select GENERIC_PINCONF help This selects the pinctrl driver for Xilinx Zynq. source "drivers/pinctrl/bcm/Kconfig" source "drivers/pinctrl/berlin/Kconfig" source "drivers/pinctrl/freescale/Kconfig" source "drivers/pinctrl/intel/Kconfig" source "drivers/pinctrl/mvebu/Kconfig" source "drivers/pinctrl/nomadik/Kconfig" source "drivers/pinctrl/pxa/Kconfig" source "drivers/pinctrl/qcom/Kconfig" source "drivers/pinctrl/samsung/Kconfig" source "drivers/pinctrl/sh-pfc/Kconfig" source "drivers/pinctrl/spear/Kconfig" source "drivers/pinctrl/stm32/Kconfig" source "drivers/pinctrl/sunxi/Kconfig" source "drivers/pinctrl/tegra/Kconfig" source "drivers/pinctrl/uniphier/Kconfig" source "drivers/pinctrl/vt8500/Kconfig" source "drivers/pinctrl/mediatek/Kconfig" config PINCTRL_XWAY bool depends on SOC_TYPE_XWAY depends on PINCTRL_LANTIQ config PINCTRL_TB10X bool depends on OF && ARC_PLAT_TB10X select GPIOLIB endmenu