/* * drivers/net/phy/marvell.c * * Driver for Marvell PHYs * * Author: Andy Fleming * * Copyright (c) 2004 Freescale Semiconductor, Inc. * * Copyright (c) 2013 Michael Stapelberg * * This program is free software; you can redistribute it and/or modify it * under the terms of the GNU General Public License as published by the * Free Software Foundation; either version 2 of the License, or (at your * option) any later version. * */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #define MII_MARVELL_PHY_PAGE 22 #define MII_M1011_IEVENT 0x13 #define MII_M1011_IEVENT_CLEAR 0x0000 #define MII_M1011_IMASK 0x12 #define MII_M1011_IMASK_INIT 0x6400 #define MII_M1011_IMASK_CLEAR 0x0000 #define MII_M1011_PHY_SCR 0x10 #define MII_M1011_PHY_SCR_MDI 0x0000 #define MII_M1011_PHY_SCR_MDI_X 0x0020 #define MII_M1011_PHY_SCR_AUTO_CROSS 0x0060 #define MII_M1145_PHY_EXT_ADDR_PAGE 0x16 #define MII_M1145_PHY_EXT_SR 0x1b #define MII_M1145_PHY_EXT_CR 0x14 #define MII_M1145_RGMII_RX_DELAY 0x0080 #define MII_M1145_RGMII_TX_DELAY 0x0002 #define MII_M1145_HWCFG_MODE_SGMII_NO_CLK 0x4 #define MII_M1145_HWCFG_MODE_MASK 0xf #define MII_M1145_HWCFG_FIBER_COPPER_AUTO 0x8000 #define MII_M1145_HWCFG_MODE_SGMII_NO_CLK 0x4 #define MII_M1145_HWCFG_MODE_MASK 0xf #define MII_M1145_HWCFG_FIBER_COPPER_AUTO 0x8000 #define MII_M1111_PHY_LED_CONTROL 0x18 #define MII_M1111_PHY_LED_DIRECT 0x4100 #define MII_M1111_PHY_LED_COMBINE 0x411c #define MII_M1111_PHY_EXT_CR 0x14 #define MII_M1111_RX_DELAY 0x80 #define MII_M1111_TX_DELAY 0x2 #define MII_M1111_PHY_EXT_SR 0x1b #define MII_M1111_HWCFG_MODE_MASK 0xf #define MII_M1111_HWCFG_MODE_COPPER_RGMII 0xb #define MII_M1111_HWCFG_MODE_FIBER_RGMII 0x3 #define MII_M1111_HWCFG_MODE_SGMII_NO_CLK 0x4 #define MII_M1111_HWCFG_MODE_COPPER_RTBI 0x9 #define MII_M1111_HWCFG_FIBER_COPPER_AUTO 0x8000 #define MII_M1111_HWCFG_FIBER_COPPER_RES 0x2000 #define MII_M1111_COPPER 0 #define MII_M1111_FIBER 1 #define MII_88E1121_PHY_MSCR_PAGE 2 #define MII_88E1121_PHY_MSCR_REG 21 #define MII_88E1121_PHY_MSCR_RX_DELAY BIT(5) #define MII_88E1121_PHY_MSCR_TX_DELAY BIT(4) #define MII_88E1121_PHY_MSCR_DELAY_MASK (~(0x3 << 4)) #define MII_88E1121_MISC_TEST 0x1a #define MII_88E1510_MISC_TEST_TEMP_THRESHOLD_MASK 0x1f00 #define MII_88E1510_MISC_TEST_TEMP_THRESHOLD_SHIFT 8 #define MII_88E1510_MISC_TEST_TEMP_IRQ_EN BIT(7) #define MII_88E1510_MISC_TEST_TEMP_IRQ BIT(6) #define MII_88E1121_MISC_TEST_TEMP_SENSOR_EN BIT(5) #define MII_88E1121_MISC_TEST_TEMP_MASK 0x1f #define MII_88E1510_TEMP_SENSOR 0x1b #define MII_88E1510_TEMP_SENSOR_MASK 0xff #define MII_88E1318S_PHY_MSCR1_REG 16 #define MII_88E1318S_PHY_MSCR1_PAD_ODD BIT(6) /* Copper Specific Interrupt Enable Register */ #define MII_88E1318S_PHY_CSIER 0x12 /* WOL Event Interrupt Enable */ #define MII_88E1318S_PHY_CSIER_WOL_EIE BIT(7) /* LED Timer Control Register */ #define MII_88E1318S_PHY_LED_PAGE 0x03 #define MII_88E1318S_PHY_LED_TCR 0x12 #define MII_88E1318S_PHY_LED_TCR_FORCE_INT BIT(15) #define MII_88E1318S_PHY_LED_TCR_INTn_ENABLE BIT(7) #define MII_88E1318S_PHY_LED_TCR_INT_ACTIVE_LOW BIT(11) /* Magic Packet MAC address registers */ #define MII_88E1318S_PHY_MAGIC_PACKET_WORD2 0x17 #define MII_88E1318S_PHY_MAGIC_PACKET_WORD1 0x18 #define MII_88E1318S_PHY_MAGIC_PACKET_WORD0 0x19 #define MII_88E1318S_PHY_WOL_PAGE 0x11 #define MII_88E1318S_PHY_WOL_CTRL 0x10 #define MII_88E1318S_PHY_WOL_CTRL_CLEAR_WOL_STATUS BIT(12) #define MII_88E1318S_PHY_WOL_CTRL_MAGIC_PACKET_MATCH_ENABLE BIT(14) #define MII_88E1121_PHY_LED_CTRL 16 #define MII_88E1121_PHY_LED_PAGE 3 #define MII_88E1121_PHY_LED_DEF 0x0030 #define MII_M1011_PHY_STATUS 0x11 #define MII_M1011_PHY_STATUS_1000 0x8000 #define MII_M1011_PHY_STATUS_100 0x4000 #define MII_M1011_PHY_STATUS_SPD_MASK 0xc000 #define MII_M1011_PHY_STATUS_FULLDUPLEX 0x2000 #define MII_M1011_PHY_STATUS_RESOLVED 0x0800 #define MII_M1011_PHY_STATUS_LINK 0x0400 #define MII_M1116R_CONTROL_REG_MAC 21 #define MII_88E3016_PHY_SPEC_CTRL 0x10 #define MII_88E3016_DISABLE_SCRAMBLER 0x0200 #define MII_88E3016_AUTO_MDIX_CROSSOVER 0x0030 #define MII_88E1510_GEN_CTRL_REG_1 0x14 #define MII_88E1510_GEN_CTRL_REG_1_MODE_MASK 0x7 #define MII_88E1510_GEN_CTRL_REG_1_MODE_SGMII 0x1 /* SGMII to copper */ #define MII_88E1510_GEN_CTRL_REG_1_RESET 0x8000 /* Soft reset */ #define LPA_FIBER_1000HALF 0x40 #define LPA_FIBER_1000FULL 0x20 #define LPA_PAUSE_FIBER 0x180 #define LPA_PAUSE_ASYM_FIBER 0x100 #define ADVERTISE_FIBER_1000HALF 0x40 #define ADVERTISE_FIBER_1000FULL 0x20 #define ADVERTISE_PAUSE_FIBER 0x180 #define ADVERTISE_PAUSE_ASYM_FIBER 0x100 #define REGISTER_LINK_STATUS 0x400 #define NB_FIBER_STATS 1 MODULE_DESCRIPTION("Marvell PHY driver"); MODULE_AUTHOR("Andy Fleming"); MODULE_LICENSE("GPL"); struct marvell_hw_stat { const char *string; u8 page; u8 reg; u8 bits; }; static struct marvell_hw_stat marvell_hw_stats[] = { { "phy_receive_errors_copper", 0, 21, 16}, { "phy_idle_errors", 0, 10, 8 }, { "phy_receive_errors_fiber", 1, 21, 16}, }; struct marvell_priv { u64 stats[ARRAY_SIZE(marvell_hw_stats)]; char *hwmon_name; struct device *hwmon_dev; }; static int marvell_get_page(struct phy_device *phydev) { return phy_read(phydev, MII_MARVELL_PHY_PAGE); } static int marvell_set_page(struct phy_device *phydev, int page) { return phy_write(phydev, MII_MARVELL_PHY_PAGE, page); } static int marvell_ack_interrupt(struct phy_device *phydev) { int err; /* Clear the interrupts by reading the reg */ err = phy_read(phydev, MII_M1011_IEVENT); if (err < 0) return err; return 0; } static int marvell_config_intr(struct phy_device *phydev) { int err; if (phydev->interrupts == PHY_INTERRUPT_ENABLED) err = phy_write(phydev, MII_M1011_IMASK, MII_M1011_IMASK_INIT); else err = phy_write(phydev, MII_M1011_IMASK, MII_M1011_IMASK_CLEAR); return err; } static int marvell_set_polarity(struct phy_device *phydev, int polarity) { int reg; int err; int val; /* get the current settings */ reg = phy_read(phydev, MII_M1011_PHY_SCR); if (reg < 0) return reg; val = reg; val &= ~MII_M1011_PHY_SCR_AUTO_CROSS; switch (polarity) { case ETH_TP_MDI: val |= MII_M1011_PHY_SCR_MDI; break; case ETH_TP_MDI_X: val |= MII_M1011_PHY_SCR_MDI_X; break; case ETH_TP_MDI_AUTO: case ETH_TP_MDI_INVALID: default: val |= MII_M1011_PHY_SCR_AUTO_CROSS; break; } if (val != reg) { /* Set the new polarity value in the register */ err = phy_write(phydev, MII_M1011_PHY_SCR, val); if (err) return err; } return 0; } static int marvell_config_aneg(struct phy_device *phydev) { int err; /* The Marvell PHY has an errata which requires * that certain registers get written in order * to restart autonegotiation */ err = phy_write(phydev, MII_BMCR, BMCR_RESET); if (err < 0) return err; err = phy_write(phydev, 0x1d, 0x1f); if (err < 0) return err; err = phy_write(phydev, 0x1e, 0x200c); if (err < 0) return err; err = phy_write(phydev, 0x1d, 0x5); if (err < 0) return err; err = phy_write(phydev, 0x1e, 0); if (err < 0) return err; err = phy_write(phydev, 0x1e, 0x100); if (err < 0) return err; err = marvell_set_polarity(phydev, phydev->mdix_ctrl); if (err < 0) return err; err = phy_write(phydev, MII_M1111_PHY_LED_CONTROL, MII_M1111_PHY_LED_DIRECT); if (err < 0) return err; err = genphy_config_aneg(phydev); if (err < 0) return err; if (phydev->autoneg != AUTONEG_ENABLE) { int bmcr; /* A write to speed/duplex bits (that is performed by * genphy_config_aneg() call above) must be followed by * a software reset. Otherwise, the write has no effect. */ bmcr = phy_read(phydev, MII_BMCR); if (bmcr < 0) return bmcr; err = phy_write(phydev, MII_BMCR, bmcr | BMCR_RESET); if (err < 0) return err; } return 0; } static int m88e1111_config_aneg(struct phy_device *phydev) { int err; /* The Marvell PHY has an errata which requires * that certain registers get written in order * to restart autonegotiation */ err = phy_write(phydev, MII_BMCR, BMCR_RESET); err = marvell_set_polarity(phydev, phydev->mdix_ctrl); if (err < 0) return err; err = phy_write(phydev, MII_M1111_PHY_LED_CONTROL, MII_M1111_PHY_LED_DIRECT); if (err < 0) return err; err = genphy_config_aneg(phydev); if (err < 0) return err; if (phydev->autoneg != AUTONEG_ENABLE) { int bmcr; /* A write to speed/duplex bits (that is performed by * genphy_config_aneg() call above) must be followed by * a software reset. Otherwise, the write has no effect. */ bmcr = phy_read(phydev, MII_BMCR); if (bmcr < 0) return bmcr; err = phy_write(phydev, MII_BMCR, bmcr | BMCR_RESET); if (err < 0) return err; } return 0; } #ifdef CONFIG_OF_MDIO /* Set and/or override some configuration registers based on the * marvell,reg-init property stored in the of_node for the phydev. * * marvell,reg-init = ,...; * * There may be one or more sets of : * * reg-page: which register bank to use. * reg: the register. * mask: if non-zero, ANDed with existing register value. * value: ORed with the masked value and written to the regiser. * */ static int marvell_of_reg_init(struct phy_device *phydev) { const __be32 *paddr; int len, i, saved_page, current_page, ret; if (!phydev->mdio.dev.of_node) return 0; paddr = of_get_property(phydev->mdio.dev.of_node, "marvell,reg-init", &len); if (!paddr || len < (4 * sizeof(*paddr))) return 0; saved_page = marvell_get_page(phydev); if (saved_page < 0) return saved_page; current_page = saved_page; ret = 0; len /= sizeof(*paddr); for (i = 0; i < len - 3; i += 4) { u16 page = be32_to_cpup(paddr + i); u16 reg = be32_to_cpup(paddr + i + 1); u16 mask = be32_to_cpup(paddr + i + 2); u16 val_bits = be32_to_cpup(paddr + i + 3); int val; if (page != current_page) { current_page = page; ret = marvell_set_page(phydev, page); if (ret < 0) goto err; } val = 0; if (mask) { val = phy_read(phydev, reg); if (val < 0) { ret = val; goto err; } val &= mask; } val |= val_bits; ret = phy_write(phydev, reg, val); if (ret < 0) goto err; } err: if (current_page != saved_page) { i = marvell_set_page(phydev, saved_page); if (ret == 0) ret = i; } return ret; } #else static int marvell_of_reg_init(struct phy_device *phydev) { return 0; } #endif /* CONFIG_OF_MDIO */ static int m88e1121_config_aneg(struct phy_device *phydev) { int err, oldpage, mscr; oldpage = marvell_get_page(phydev); err = marvell_set_page(phydev, MII_88E1121_PHY_MSCR_PAGE); if (err < 0) return err; if (phy_interface_is_rgmii(phydev)) { mscr = phy_read(phydev, MII_88E1121_PHY_MSCR_REG) & MII_88E1121_PHY_MSCR_DELAY_MASK; if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) mscr |= (MII_88E1121_PHY_MSCR_RX_DELAY | MII_88E1121_PHY_MSCR_TX_DELAY); else if (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) mscr |= MII_88E1121_PHY_MSCR_RX_DELAY; else if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID) mscr |= MII_88E1121_PHY_MSCR_TX_DELAY; err = phy_write(phydev, MII_88E1121_PHY_MSCR_REG, mscr); if (err < 0) return err; } marvell_set_page(phydev, oldpage); err = phy_write(phydev, MII_BMCR, BMCR_RESET); if (err < 0) return err; err = phy_write(phydev, MII_M1011_PHY_SCR, MII_M1011_PHY_SCR_AUTO_CROSS); if (err < 0) return err; return genphy_config_aneg(phydev); } static int m88e1318_config_aneg(struct phy_device *phydev) { int err, oldpage, mscr; oldpage = marvell_get_page(phydev); err = marvell_set_page(phydev, MII_88E1121_PHY_MSCR_PAGE); if (err < 0) return err; mscr = phy_read(phydev, MII_88E1318S_PHY_MSCR1_REG); mscr |= MII_88E1318S_PHY_MSCR1_PAD_ODD; err = phy_write(phydev, MII_88E1318S_PHY_MSCR1_REG, mscr); if (err < 0) return err; err = marvell_set_page(phydev, oldpage); if (err < 0) return err; return m88e1121_config_aneg(phydev); } /** * ethtool_adv_to_fiber_adv_t * @ethadv: the ethtool advertisement settings * * A small helper function that translates ethtool advertisement * settings to phy autonegotiation advertisements for the * MII_ADV register for fiber link. */ static inline u32 ethtool_adv_to_fiber_adv_t(u32 ethadv) { u32 result = 0; if (ethadv & ADVERTISED_1000baseT_Half) result |= ADVERTISE_FIBER_1000HALF; if (ethadv & ADVERTISED_1000baseT_Full) result |= ADVERTISE_FIBER_1000FULL; if ((ethadv & ADVERTISE_PAUSE_ASYM) && (ethadv & ADVERTISE_PAUSE_CAP)) result |= LPA_PAUSE_ASYM_FIBER; else if (ethadv & ADVERTISE_PAUSE_CAP) result |= (ADVERTISE_PAUSE_FIBER & (~ADVERTISE_PAUSE_ASYM_FIBER)); return result; } /** * marvell_config_aneg_fiber - restart auto-negotiation or write BMCR * @phydev: target phy_device struct * * Description: If auto-negotiation is enabled, we configure the * advertising, and then restart auto-negotiation. If it is not * enabled, then we write the BMCR. Adapted for fiber link in * some Marvell's devices. */ static int marvell_config_aneg_fiber(struct phy_device *phydev) { int changed = 0; int err; int adv, oldadv; u32 advertise; if (phydev->autoneg != AUTONEG_ENABLE) return genphy_setup_forced(phydev); /* Only allow advertising what this PHY supports */ phydev->advertising &= phydev->supported; advertise = phydev->advertising; /* Setup fiber advertisement */ adv = phy_read(phydev, MII_ADVERTISE); if (adv < 0) return adv; oldadv = adv; adv &= ~(ADVERTISE_FIBER_1000HALF | ADVERTISE_FIBER_1000FULL | LPA_PAUSE_FIBER); adv |= ethtool_adv_to_fiber_adv_t(advertise); if (adv != oldadv) { err = phy_write(phydev, MII_ADVERTISE, adv); if (err < 0) return err; changed = 1; } if (changed == 0) { /* Advertisement hasn't changed, but maybe aneg was never on to * begin with? Or maybe phy was isolated? */ int ctl = phy_read(phydev, MII_BMCR); if (ctl < 0) return ctl; if (!(ctl & BMCR_ANENABLE) || (ctl & BMCR_ISOLATE)) changed = 1; /* do restart aneg */ } /* Only restart aneg if we are advertising something different * than we were before. */ if (changed > 0) changed = genphy_restart_aneg(phydev); return changed; } static int m88e1510_config_aneg(struct phy_device *phydev) { int err; err = marvell_set_page(phydev, MII_M1111_COPPER); if (err < 0) goto error; /* Configure the copper link first */ err = m88e1318_config_aneg(phydev); if (err < 0) goto error; /* Then the fiber link */ err = marvell_set_page(phydev, MII_M1111_FIBER); if (err < 0) goto error; err = marvell_config_aneg_fiber(phydev); if (err < 0) goto error; return marvell_set_page(phydev, MII_M1111_COPPER); error: marvell_set_page(phydev, MII_M1111_COPPER); return err; } static int marvell_config_init(struct phy_device *phydev) { /* Set registers from marvell,reg-init DT property */ return marvell_of_reg_init(phydev); } static int m88e1116r_config_init(struct phy_device *phydev) { int temp; int err; temp = phy_read(phydev, MII_BMCR); temp |= BMCR_RESET; err = phy_write(phydev, MII_BMCR, temp); if (err < 0) return err; mdelay(500); err = marvell_set_page(phydev, MII_M1111_COPPER); if (err < 0) return err; temp = phy_read(phydev, MII_M1011_PHY_SCR); temp |= (7 << 12); /* max number of gigabit attempts */ temp |= (1 << 11); /* enable downshift */ temp |= MII_M1011_PHY_SCR_AUTO_CROSS; err = phy_write(phydev, MII_M1011_PHY_SCR, temp); if (err < 0) return err; err = marvell_set_page(phydev, MII_88E1121_PHY_MSCR_PAGE); if (err < 0) return err; temp = phy_read(phydev, MII_M1116R_CONTROL_REG_MAC); temp |= (1 << 5); temp |= (1 << 4); err = phy_write(phydev, MII_M1116R_CONTROL_REG_MAC, temp); if (err < 0) return err; err = marvell_set_page(phydev, MII_M1111_COPPER); if (err < 0) return err; temp = phy_read(phydev, MII_BMCR); temp |= BMCR_RESET; err = phy_write(phydev, MII_BMCR, temp); if (err < 0) return err; mdelay(500); return marvell_config_init(phydev); } static int m88e3016_config_init(struct phy_device *phydev) { int reg; /* Enable Scrambler and Auto-Crossover */ reg = phy_read(phydev, MII_88E3016_PHY_SPEC_CTRL); if (reg < 0) return reg; reg &= ~MII_88E3016_DISABLE_SCRAMBLER; reg |= MII_88E3016_AUTO_MDIX_CROSSOVER; reg = phy_write(phydev, MII_88E3016_PHY_SPEC_CTRL, reg); if (reg < 0) return reg; return marvell_config_init(phydev); } static int m88e1111_config_init_rgmii(struct phy_device *phydev) { int err; int temp; temp = phy_read(phydev, MII_M1111_PHY_EXT_CR); if (temp < 0) return temp; if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) { temp |= (MII_M1111_RX_DELAY | MII_M1111_TX_DELAY); } else if (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) { temp &= ~MII_M1111_TX_DELAY; temp |= MII_M1111_RX_DELAY; } else if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID) { temp &= ~MII_M1111_RX_DELAY; temp |= MII_M1111_TX_DELAY; } err = phy_write(phydev, MII_M1111_PHY_EXT_CR, temp); if (err < 0) return err; temp = phy_read(phydev, MII_M1111_PHY_EXT_SR); if (temp < 0) return temp; temp &= ~(MII_M1111_HWCFG_MODE_MASK); if (temp & MII_M1111_HWCFG_FIBER_COPPER_RES) temp |= MII_M1111_HWCFG_MODE_FIBER_RGMII; else temp |= MII_M1111_HWCFG_MODE_COPPER_RGMII; return phy_write(phydev, MII_M1111_PHY_EXT_SR, temp); } static int m88e1111_config_init_sgmii(struct phy_device *phydev) { int err; int temp; temp = phy_read(phydev, MII_M1111_PHY_EXT_SR); if (temp < 0) return temp; temp &= ~(MII_M1111_HWCFG_MODE_MASK); temp |= MII_M1111_HWCFG_MODE_SGMII_NO_CLK; temp |= MII_M1111_HWCFG_FIBER_COPPER_AUTO; err = phy_write(phydev, MII_M1111_PHY_EXT_SR, temp); if (err < 0) return err; /* make sure copper is selected */ err = phy_read(phydev, MII_M1145_PHY_EXT_ADDR_PAGE); if (err < 0) return err; return phy_write(phydev, MII_M1145_PHY_EXT_ADDR_PAGE, err & (~0xff)); } static int m88e1111_config_init_rtbi(struct phy_device *phydev) { int err; int temp; temp = phy_read(phydev, MII_M1111_PHY_EXT_CR); if (temp < 0) return temp; temp |= (MII_M1111_RX_DELAY | MII_M1111_TX_DELAY); err = phy_write(phydev, MII_M1111_PHY_EXT_CR, temp); if (err < 0) return err; temp = phy_read(phydev, MII_M1111_PHY_EXT_SR); if (temp < 0) return temp; temp &= ~(MII_M1111_HWCFG_MODE_MASK | MII_M1111_HWCFG_FIBER_COPPER_RES); temp |= 0x7 | MII_M1111_HWCFG_FIBER_COPPER_AUTO; err = phy_write(phydev, MII_M1111_PHY_EXT_SR, temp); if (err < 0) return err; /* soft reset */ err = phy_write(phydev, MII_BMCR, BMCR_RESET); if (err < 0) return err; do temp = phy_read(phydev, MII_BMCR); while (temp & BMCR_RESET); temp = phy_read(phydev, MII_M1111_PHY_EXT_SR); if (temp < 0) return temp; temp &= ~(MII_M1111_HWCFG_MODE_MASK | MII_M1111_HWCFG_FIBER_COPPER_RES); temp |= MII_M1111_HWCFG_MODE_COPPER_RTBI | MII_M1111_HWCFG_FIBER_COPPER_AUTO; return phy_write(phydev, MII_M1111_PHY_EXT_SR, temp); } static int m88e1111_config_init(struct phy_device *phydev) { int err; if (phy_interface_is_rgmii(phydev)) { err = m88e1111_config_init_rgmii(phydev); if (err) return err; } if (phydev->interface == PHY_INTERFACE_MODE_SGMII) { err = m88e1111_config_init_sgmii(phydev); if (err < 0) return err; } if (phydev->interface == PHY_INTERFACE_MODE_RTBI) { err = m88e1111_config_init_rtbi(phydev); if (err < 0) return err; } err = marvell_of_reg_init(phydev); if (err < 0) return err; return phy_write(phydev, MII_BMCR, BMCR_RESET); } static int m88e1121_config_init(struct phy_device *phydev) { int err, oldpage; oldpage = marvell_get_page(phydev); err = marvell_set_page(phydev, MII_88E1121_PHY_LED_PAGE); if (err < 0) return err; /* Default PHY LED config: LED[0] .. Link, LED[1] .. Activity */ err = phy_write(phydev, MII_88E1121_PHY_LED_CTRL, MII_88E1121_PHY_LED_DEF); if (err < 0) return err; marvell_set_page(phydev, oldpage); /* Set marvell,reg-init configuration from device tree */ return marvell_config_init(phydev); } static int m88e1510_config_init(struct phy_device *phydev) { int err; int temp; /* SGMII-to-Copper mode initialization */ if (phydev->interface == PHY_INTERFACE_MODE_SGMII) { /* Select page 18 */ err = marvell_set_page(phydev, 18); if (err < 0) return err; /* In reg 20, write MODE[2:0] = 0x1 (SGMII to Copper) */ temp = phy_read(phydev, MII_88E1510_GEN_CTRL_REG_1); temp &= ~MII_88E1510_GEN_CTRL_REG_1_MODE_MASK; temp |= MII_88E1510_GEN_CTRL_REG_1_MODE_SGMII; err = phy_write(phydev, MII_88E1510_GEN_CTRL_REG_1, temp); if (err < 0) return err; /* PHY reset is necessary after changing MODE[2:0] */ temp |= MII_88E1510_GEN_CTRL_REG_1_RESET; err = phy_write(phydev, MII_88E1510_GEN_CTRL_REG_1, temp); if (err < 0) return err; /* Reset page selection */ err = marvell_set_page(phydev, MII_M1111_COPPER); if (err < 0) return err; } return m88e1121_config_init(phydev); } static int m88e1118_config_aneg(struct phy_device *phydev) { int err; err = phy_write(phydev, MII_BMCR, BMCR_RESET); if (err < 0) return err; err = phy_write(phydev, MII_M1011_PHY_SCR, MII_M1011_PHY_SCR_AUTO_CROSS); if (err < 0) return err; err = genphy_config_aneg(phydev); return 0; } static int m88e1118_config_init(struct phy_device *phydev) { int err; /* Change address */ err = marvell_set_page(phydev, MII_88E1121_PHY_MSCR_PAGE); if (err < 0) return err; /* Enable 1000 Mbit */ err = phy_write(phydev, 0x15, 0x1070); if (err < 0) return err; /* Change address */ err = marvell_set_page(phydev, MII_88E1318S_PHY_LED_PAGE); if (err < 0) return err; /* Adjust LED Control */ if (phydev->dev_flags & MARVELL_PHY_M1118_DNS323_LEDS) err = phy_write(phydev, 0x10, 0x1100); else err = phy_write(phydev, 0x10, 0x021e); if (err < 0) return err; err = marvell_of_reg_init(phydev); if (err < 0) return err; /* Reset address */ err = marvell_set_page(phydev, MII_M1111_COPPER); if (err < 0) return err; return phy_write(phydev, MII_BMCR, BMCR_RESET); } static int m88e1149_config_init(struct phy_device *phydev) { int err; /* Change address */ err = marvell_set_page(phydev, MII_88E1121_PHY_MSCR_PAGE); if (err < 0) return err; /* Enable 1000 Mbit */ err = phy_write(phydev, 0x15, 0x1048); if (err < 0) return err; err = marvell_of_reg_init(phydev); if (err < 0) return err; /* Reset address */ err = marvell_set_page(phydev, MII_M1111_COPPER); if (err < 0) return err; return phy_write(phydev, MII_BMCR, BMCR_RESET); } static int m88e1145_config_init_rgmii(struct phy_device *phydev) { int err; int temp = phy_read(phydev, MII_M1145_PHY_EXT_CR); if (temp < 0) return temp; temp |= (MII_M1145_RGMII_RX_DELAY | MII_M1145_RGMII_TX_DELAY); err = phy_write(phydev, MII_M1145_PHY_EXT_CR, temp); if (err < 0) return err; if (phydev->dev_flags & MARVELL_PHY_M1145_FLAGS_RESISTANCE) { err = phy_write(phydev, 0x1d, 0x0012); if (err < 0) return err; temp = phy_read(phydev, 0x1e); if (temp < 0) return temp; temp &= 0xf03f; temp |= 2 << 9; /* 36 ohm */ temp |= 2 << 6; /* 39 ohm */ err = phy_write(phydev, 0x1e, temp); if (err < 0) return err; err = phy_write(phydev, 0x1d, 0x3); if (err < 0) return err; err = phy_write(phydev, 0x1e, 0x8000); } return err; } static int m88e1145_config_init_sgmii(struct phy_device *phydev) { int temp = phy_read(phydev, MII_M1145_PHY_EXT_SR); if (temp < 0) return temp; temp &= ~MII_M1145_HWCFG_MODE_MASK; temp |= MII_M1145_HWCFG_MODE_SGMII_NO_CLK; temp |= MII_M1145_HWCFG_FIBER_COPPER_AUTO; return phy_write(phydev, MII_M1145_PHY_EXT_SR, temp); } static int m88e1145_config_init(struct phy_device *phydev) { int err; /* Take care of errata E0 & E1 */ err = phy_write(phydev, 0x1d, 0x001b); if (err < 0) return err; err = phy_write(phydev, 0x1e, 0x418f); if (err < 0) return err; err = phy_write(phydev, 0x1d, 0x0016); if (err < 0) return err; err = phy_write(phydev, 0x1e, 0xa2da); if (err < 0) return err; if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) { err = m88e1145_config_init_rgmii(phydev); if (err < 0) return err; } if (phydev->interface == PHY_INTERFACE_MODE_SGMII) { err = m88e1145_config_init_sgmii(phydev); if (err < 0) return err; } err = marvell_of_reg_init(phydev); if (err < 0) return err; return 0; } /** * fiber_lpa_to_ethtool_lpa_t * @lpa: value of the MII_LPA register for fiber link * * A small helper function that translates MII_LPA * bits to ethtool LP advertisement settings. */ static u32 fiber_lpa_to_ethtool_lpa_t(u32 lpa) { u32 result = 0; if (lpa & LPA_FIBER_1000HALF) result |= ADVERTISED_1000baseT_Half; if (lpa & LPA_FIBER_1000FULL) result |= ADVERTISED_1000baseT_Full; return result; } /** * marvell_update_link - update link status in real time in @phydev * @phydev: target phy_device struct * * Description: Update the value in phydev->link to reflect the * current link value. */ static int marvell_update_link(struct phy_device *phydev, int fiber) { int status; /* Use the generic register for copper link, or specific * register for fiber case */ if (fiber) { status = phy_read(phydev, MII_M1011_PHY_STATUS); if (status < 0) return status; if ((status & REGISTER_LINK_STATUS) == 0) phydev->link = 0; else phydev->link = 1; } else { return genphy_update_link(phydev); } return 0; } static int marvell_read_status_page_an(struct phy_device *phydev, int fiber) { int status; int lpa; int lpagb; int adv; status = phy_read(phydev, MII_M1011_PHY_STATUS); if (status < 0) return status; lpa = phy_read(phydev, MII_LPA); if (lpa < 0) return lpa; lpagb = phy_read(phydev, MII_STAT1000); if (lpagb < 0) return lpagb; adv = phy_read(phydev, MII_ADVERTISE); if (adv < 0) return adv; lpa &= adv; if (status & MII_M1011_PHY_STATUS_FULLDUPLEX) phydev->duplex = DUPLEX_FULL; else phydev->duplex = DUPLEX_HALF; status = status & MII_M1011_PHY_STATUS_SPD_MASK; phydev->pause = 0; phydev->asym_pause = 0; switch (status) { case MII_M1011_PHY_STATUS_1000: phydev->speed = SPEED_1000; break; case MII_M1011_PHY_STATUS_100: phydev->speed = SPEED_100; break; default: phydev->speed = SPEED_10; break; } if (!fiber) { phydev->lp_advertising = mii_stat1000_to_ethtool_lpa_t(lpagb) | mii_lpa_to_ethtool_lpa_t(lpa); if (phydev->duplex == DUPLEX_FULL) { phydev->pause = lpa & LPA_PAUSE_CAP ? 1 : 0; phydev->asym_pause = lpa & LPA_PAUSE_ASYM ? 1 : 0; } } else { /* The fiber link is only 1000M capable */ phydev->lp_advertising = fiber_lpa_to_ethtool_lpa_t(lpa); if (phydev->duplex == DUPLEX_FULL) { if (!(lpa & LPA_PAUSE_FIBER)) { phydev->pause = 0; phydev->asym_pause = 0; } else if ((lpa & LPA_PAUSE_ASYM_FIBER)) { phydev->pause = 1; phydev->asym_pause = 1; } else { phydev->pause = 1; phydev->asym_pause = 0; } } } return 0; } static int marvell_read_status_page_fixed(struct phy_device *phydev) { int bmcr = phy_read(phydev, MII_BMCR); if (bmcr < 0) return bmcr; if (bmcr & BMCR_FULLDPLX) phydev->duplex = DUPLEX_FULL; else phydev->duplex = DUPLEX_HALF; if (bmcr & BMCR_SPEED1000) phydev->speed = SPEED_1000; else if (bmcr & BMCR_SPEED100) phydev->speed = SPEED_100; else phydev->speed = SPEED_10; phydev->pause = 0; phydev->asym_pause = 0; phydev->lp_advertising = 0; return 0; } /* marvell_read_status_page * * Description: * Check the link, then figure out the current state * by comparing what we advertise with what the link partner * advertises. Start by checking the gigabit possibilities, * then move on to 10/100. */ static int marvell_read_status_page(struct phy_device *phydev, int page) { int fiber; int err; /* Detect and update the link, but return if there * was an error */ if (page == MII_M1111_FIBER) fiber = 1; else fiber = 0; err = marvell_update_link(phydev, fiber); if (err) return err; if (phydev->autoneg == AUTONEG_ENABLE) err = marvell_read_status_page_an(phydev, fiber); else err = marvell_read_status_page_fixed(phydev); return err; } /* marvell_read_status * * Some Marvell's phys have two modes: fiber and copper. * Both need status checked. * Description: * First, check the fiber link and status. * If the fiber link is down, check the copper link and status which * will be the default value if both link are down. */ static int marvell_read_status(struct phy_device *phydev) { int err; /* Check the fiber mode first */ if (phydev->supported & SUPPORTED_FIBRE && phydev->interface != PHY_INTERFACE_MODE_SGMII) { err = marvell_set_page(phydev, MII_M1111_FIBER); if (err < 0) goto error; err = marvell_read_status_page(phydev, MII_M1111_FIBER); if (err < 0) goto error; /* If the fiber link is up, it is the selected and * used link. In this case, we need to stay in the * fiber page. Please to be careful about that, avoid * to restore Copper page in other functions which * could break the behaviour for some fiber phy like * 88E1512. */ if (phydev->link) return 0; /* If fiber link is down, check and save copper mode state */ err = marvell_set_page(phydev, MII_M1111_COPPER); if (err < 0) goto error; } return marvell_read_status_page(phydev, MII_M1111_COPPER); error: marvell_set_page(phydev, MII_M1111_COPPER); return err; } /* marvell_suspend * * Some Marvell's phys have two modes: fiber and copper. * Both need to be suspended */ static int marvell_suspend(struct phy_device *phydev) { int err; /* Suspend the fiber mode first */ if (!(phydev->supported & SUPPORTED_FIBRE)) { err = marvell_set_page(phydev, MII_M1111_FIBER); if (err < 0) goto error; /* With the page set, use the generic suspend */ err = genphy_suspend(phydev); if (err < 0) goto error; /* Then, the copper link */ err = marvell_set_page(phydev, MII_M1111_COPPER); if (err < 0) goto error; } /* With the page set, use the generic suspend */ return genphy_suspend(phydev); error: marvell_set_page(phydev, MII_M1111_COPPER); return err; } /* marvell_resume * * Some Marvell's phys have two modes: fiber and copper. * Both need to be resumed */ static int marvell_resume(struct phy_device *phydev) { int err; /* Resume the fiber mode first */ if (!(phydev->supported & SUPPORTED_FIBRE)) { err = marvell_set_page(phydev, MII_M1111_FIBER); if (err < 0) goto error; /* With the page set, use the generic resume */ err = genphy_resume(phydev); if (err < 0) goto error; /* Then, the copper link */ err = marvell_set_page(phydev, MII_M1111_COPPER); if (err < 0) goto error; } /* With the page set, use the generic resume */ return genphy_resume(phydev); error: marvell_set_page(phydev, MII_M1111_COPPER); return err; } static int marvell_aneg_done(struct phy_device *phydev) { int retval = phy_read(phydev, MII_M1011_PHY_STATUS); return (retval < 0) ? retval : (retval & MII_M1011_PHY_STATUS_RESOLVED); } static int m88e1121_did_interrupt(struct phy_device *phydev) { int imask; imask = phy_read(phydev, MII_M1011_IEVENT); if (imask & MII_M1011_IMASK_INIT) return 1; return 0; } static void m88e1318_get_wol(struct phy_device *phydev, struct ethtool_wolinfo *wol) { wol->supported = WAKE_MAGIC; wol->wolopts = 0; if (marvell_set_page(phydev, MII_88E1318S_PHY_WOL_PAGE) < 0) return; if (phy_read(phydev, MII_88E1318S_PHY_WOL_CTRL) & MII_88E1318S_PHY_WOL_CTRL_MAGIC_PACKET_MATCH_ENABLE) wol->wolopts |= WAKE_MAGIC; if (marvell_set_page(phydev, MII_M1111_COPPER) < 0) return; } static int m88e1318_set_wol(struct phy_device *phydev, struct ethtool_wolinfo *wol) { int err, oldpage, temp; oldpage = marvell_get_page(phydev); if (wol->wolopts & WAKE_MAGIC) { /* Explicitly switch to page 0x00, just to be sure */ err = marvell_set_page(phydev, MII_M1111_COPPER); if (err < 0) return err; /* Enable the WOL interrupt */ temp = phy_read(phydev, MII_88E1318S_PHY_CSIER); temp |= MII_88E1318S_PHY_CSIER_WOL_EIE; err = phy_write(phydev, MII_88E1318S_PHY_CSIER, temp); if (err < 0) return err; err = marvell_set_page(phydev, MII_88E1318S_PHY_LED_PAGE); if (err < 0) return err; /* Setup LED[2] as interrupt pin (active low) */ temp = phy_read(phydev, MII_88E1318S_PHY_LED_TCR); temp &= ~MII_88E1318S_PHY_LED_TCR_FORCE_INT; temp |= MII_88E1318S_PHY_LED_TCR_INTn_ENABLE; temp |= MII_88E1318S_PHY_LED_TCR_INT_ACTIVE_LOW; err = phy_write(phydev, MII_88E1318S_PHY_LED_TCR, temp); if (err < 0) return err; err = marvell_set_page(phydev, MII_88E1318S_PHY_WOL_PAGE); if (err < 0) return err; /* Store the device address for the magic packet */ err = phy_write(phydev, MII_88E1318S_PHY_MAGIC_PACKET_WORD2, ((phydev->attached_dev->dev_addr[5] << 8) | phydev->attached_dev->dev_addr[4])); if (err < 0) return err; err = phy_write(phydev, MII_88E1318S_PHY_MAGIC_PACKET_WORD1, ((phydev->attached_dev->dev_addr[3] << 8) | phydev->attached_dev->dev_addr[2])); if (err < 0) return err; err = phy_write(phydev, MII_88E1318S_PHY_MAGIC_PACKET_WORD0, ((phydev->attached_dev->dev_addr[1] << 8) | phydev->attached_dev->dev_addr[0])); if (err < 0) return err; /* Clear WOL status and enable magic packet matching */ temp = phy_read(phydev, MII_88E1318S_PHY_WOL_CTRL); temp |= MII_88E1318S_PHY_WOL_CTRL_CLEAR_WOL_STATUS; temp |= MII_88E1318S_PHY_WOL_CTRL_MAGIC_PACKET_MATCH_ENABLE; err = phy_write(phydev, MII_88E1318S_PHY_WOL_CTRL, temp); if (err < 0) return err; } else { err = marvell_set_page(phydev, MII_88E1318S_PHY_WOL_PAGE); if (err < 0) return err; /* Clear WOL status and disable magic packet matching */ temp = phy_read(phydev, MII_88E1318S_PHY_WOL_CTRL); temp |= MII_88E1318S_PHY_WOL_CTRL_CLEAR_WOL_STATUS; temp &= ~MII_88E1318S_PHY_WOL_CTRL_MAGIC_PACKET_MATCH_ENABLE; err = phy_write(phydev, MII_88E1318S_PHY_WOL_CTRL, temp); if (err < 0) return err; } err = marvell_set_page(phydev, oldpage); if (err < 0) return err; return 0; } static int marvell_get_sset_count(struct phy_device *phydev) { if (phydev->supported & SUPPORTED_FIBRE) return ARRAY_SIZE(marvell_hw_stats); else return ARRAY_SIZE(marvell_hw_stats) - NB_FIBER_STATS; } static void marvell_get_strings(struct phy_device *phydev, u8 *data) { int i; for (i = 0; i < ARRAY_SIZE(marvell_hw_stats); i++) { memcpy(data + i * ETH_GSTRING_LEN, marvell_hw_stats[i].string, ETH_GSTRING_LEN); } } #ifndef UINT64_MAX #define UINT64_MAX (u64)(~((u64)0)) #endif static u64 marvell_get_stat(struct phy_device *phydev, int i) { struct marvell_hw_stat stat = marvell_hw_stats[i]; struct marvell_priv *priv = phydev->priv; int err, oldpage, val; u64 ret; oldpage = marvell_get_page(phydev); err = marvell_set_page(phydev, stat.page); if (err < 0) return UINT64_MAX; val = phy_read(phydev, stat.reg); if (val < 0) { ret = UINT64_MAX; } else { val = val & ((1 << stat.bits) - 1); priv->stats[i] += val; ret = priv->stats[i]; } marvell_set_page(phydev, oldpage); return ret; } static void marvell_get_stats(struct phy_device *phydev, struct ethtool_stats *stats, u64 *data) { int i; for (i = 0; i < ARRAY_SIZE(marvell_hw_stats); i++) data[i] = marvell_get_stat(phydev, i); } #ifdef CONFIG_HWMON static int m88e1121_get_temp(struct phy_device *phydev, long *temp) { int ret; int val; *temp = 0; mutex_lock(&phydev->lock); ret = phy_write(phydev, MII_M1145_PHY_EXT_ADDR_PAGE, 0x6); if (ret < 0) goto error; /* Enable temperature sensor */ ret = phy_read(phydev, MII_88E1121_MISC_TEST); if (ret < 0) goto error; ret = phy_write(phydev, MII_88E1121_MISC_TEST, ret | MII_88E1121_MISC_TEST_TEMP_SENSOR_EN); if (ret < 0) goto error; /* Wait for temperature to stabilize */ usleep_range(10000, 12000); val = phy_read(phydev, MII_88E1121_MISC_TEST); if (val < 0) { ret = val; goto error; } /* Disable temperature sensor */ ret = phy_write(phydev, MII_88E1121_MISC_TEST, ret & ~MII_88E1121_MISC_TEST_TEMP_SENSOR_EN); if (ret < 0) goto error; *temp = ((val & MII_88E1121_MISC_TEST_TEMP_MASK) - 5) * 5000; error: phy_write(phydev, MII_M1145_PHY_EXT_ADDR_PAGE, 0x0); mutex_unlock(&phydev->lock); return ret; } static int m88e1121_hwmon_read(struct device *dev, enum hwmon_sensor_types type, u32 attr, int channel, long *temp) { struct phy_device *phydev = dev_get_drvdata(dev); int err; switch (attr) { case hwmon_temp_input: err = m88e1121_get_temp(phydev, temp); break; default: return -EOPNOTSUPP; } return err; } static umode_t m88e1121_hwmon_is_visible(const void *data, enum hwmon_sensor_types type, u32 attr, int channel) { if (type != hwmon_temp) return 0; switch (attr) { case hwmon_temp_input: return 0444; default: return 0; } } static u32 m88e1121_hwmon_chip_config[] = { HWMON_C_REGISTER_TZ, 0 }; static const struct hwmon_channel_info m88e1121_hwmon_chip = { .type = hwmon_chip, .config = m88e1121_hwmon_chip_config, }; static u32 m88e1121_hwmon_temp_config[] = { HWMON_T_INPUT, 0 }; static const struct hwmon_channel_info m88e1121_hwmon_temp = { .type = hwmon_temp, .config = m88e1121_hwmon_temp_config, }; static const struct hwmon_channel_info *m88e1121_hwmon_info[] = { &m88e1121_hwmon_chip, &m88e1121_hwmon_temp, NULL }; static const struct hwmon_ops m88e1121_hwmon_hwmon_ops = { .is_visible = m88e1121_hwmon_is_visible, .read = m88e1121_hwmon_read, }; static const struct hwmon_chip_info m88e1121_hwmon_chip_info = { .ops = &m88e1121_hwmon_hwmon_ops, .info = m88e1121_hwmon_info, }; static int m88e1510_get_temp(struct phy_device *phydev, long *temp) { int ret; *temp = 0; mutex_lock(&phydev->lock); ret = phy_write(phydev, MII_M1145_PHY_EXT_ADDR_PAGE, 0x6); if (ret < 0) goto error; ret = phy_read(phydev, MII_88E1510_TEMP_SENSOR); if (ret < 0) goto error; *temp = ((ret & MII_88E1510_TEMP_SENSOR_MASK) - 25) * 1000; error: phy_write(phydev, MII_M1145_PHY_EXT_ADDR_PAGE, 0x0); mutex_unlock(&phydev->lock); return ret; } int m88e1510_get_temp_critical(struct phy_device *phydev, long *temp) { int ret; *temp = 0; mutex_lock(&phydev->lock); ret = phy_write(phydev, MII_M1145_PHY_EXT_ADDR_PAGE, 0x6); if (ret < 0) goto error; ret = phy_read(phydev, MII_88E1121_MISC_TEST); if (ret < 0) goto error; *temp = (((ret & MII_88E1510_MISC_TEST_TEMP_THRESHOLD_MASK) >> MII_88E1510_MISC_TEST_TEMP_THRESHOLD_SHIFT) * 5) - 25; /* convert to mC */ *temp *= 1000; error: phy_write(phydev, MII_M1145_PHY_EXT_ADDR_PAGE, 0x0); mutex_unlock(&phydev->lock); return ret; } int m88e1510_set_temp_critical(struct phy_device *phydev, long temp) { int ret; mutex_lock(&phydev->lock); ret = phy_write(phydev, MII_M1145_PHY_EXT_ADDR_PAGE, 0x6); if (ret < 0) goto error; ret = phy_read(phydev, MII_88E1121_MISC_TEST); if (ret < 0) goto error; temp = temp / 1000; temp = clamp_val(DIV_ROUND_CLOSEST(temp, 5) + 5, 0, 0x1f); ret = phy_write(phydev, MII_88E1121_MISC_TEST, (ret & ~MII_88E1510_MISC_TEST_TEMP_THRESHOLD_MASK) | (temp << MII_88E1510_MISC_TEST_TEMP_THRESHOLD_SHIFT)); error: phy_write(phydev, MII_M1145_PHY_EXT_ADDR_PAGE, 0x0); mutex_unlock(&phydev->lock); return ret; } int m88e1510_get_temp_alarm(struct phy_device *phydev, long *alarm) { int ret; *alarm = false; mutex_lock(&phydev->lock); ret = phy_write(phydev, MII_M1145_PHY_EXT_ADDR_PAGE, 0x6); if (ret < 0) goto error; ret = phy_read(phydev, MII_88E1121_MISC_TEST); if (ret < 0) goto error; *alarm = !!(ret & MII_88E1510_MISC_TEST_TEMP_IRQ); error: phy_write(phydev, MII_M1145_PHY_EXT_ADDR_PAGE, 0x0); mutex_unlock(&phydev->lock); return ret; } static int m88e1510_hwmon_read(struct device *dev, enum hwmon_sensor_types type, u32 attr, int channel, long *temp) { struct phy_device *phydev = dev_get_drvdata(dev); int err; switch (attr) { case hwmon_temp_input: err = m88e1510_get_temp(phydev, temp); break; case hwmon_temp_crit: err = m88e1510_get_temp_critical(phydev, temp); break; case hwmon_temp_max_alarm: err = m88e1510_get_temp_alarm(phydev, temp); break; default: return -EOPNOTSUPP; } return err; } static int m88e1510_hwmon_write(struct device *dev, enum hwmon_sensor_types type, u32 attr, int channel, long temp) { struct phy_device *phydev = dev_get_drvdata(dev); int err; switch (attr) { case hwmon_temp_crit: err = m88e1510_set_temp_critical(phydev, temp); break; default: return -EOPNOTSUPP; } return err; } static umode_t m88e1510_hwmon_is_visible(const void *data, enum hwmon_sensor_types type, u32 attr, int channel) { if (type != hwmon_temp) return 0; switch (attr) { case hwmon_temp_input: case hwmon_temp_max_alarm: return 0444; case hwmon_temp_crit: return 0644; default: return 0; } } static u32 m88e1510_hwmon_temp_config[] = { HWMON_T_INPUT | HWMON_T_CRIT | HWMON_T_MAX_ALARM, 0 }; static const struct hwmon_channel_info m88e1510_hwmon_temp = { .type = hwmon_temp, .config = m88e1510_hwmon_temp_config, }; static const struct hwmon_channel_info *m88e1510_hwmon_info[] = { &m88e1121_hwmon_chip, &m88e1510_hwmon_temp, NULL }; static const struct hwmon_ops m88e1510_hwmon_hwmon_ops = { .is_visible = m88e1510_hwmon_is_visible, .read = m88e1510_hwmon_read, .write = m88e1510_hwmon_write, }; static const struct hwmon_chip_info m88e1510_hwmon_chip_info = { .ops = &m88e1510_hwmon_hwmon_ops, .info = m88e1510_hwmon_info, }; static int marvell_hwmon_name(struct phy_device *phydev) { struct marvell_priv *priv = phydev->priv; struct device *dev = &phydev->mdio.dev; const char *devname = dev_name(dev); size_t len = strlen(devname); int i, j; priv->hwmon_name = devm_kzalloc(dev, len, GFP_KERNEL); if (!priv->hwmon_name) return -ENOMEM; for (i = j = 0; i < len && devname[i]; i++) { if (isalnum(devname[i])) priv->hwmon_name[j++] = devname[i]; } return 0; } static int marvell_hwmon_probe(struct phy_device *phydev, const struct hwmon_chip_info *chip) { struct marvell_priv *priv = phydev->priv; struct device *dev = &phydev->mdio.dev; int err; err = marvell_hwmon_name(phydev); if (err) return err; priv->hwmon_dev = devm_hwmon_device_register_with_info( dev, priv->hwmon_name, phydev, chip, NULL); return PTR_ERR_OR_ZERO(priv->hwmon_dev); } static int m88e1121_hwmon_probe(struct phy_device *phydev) { return marvell_hwmon_probe(phydev, &m88e1121_hwmon_chip_info); } static int m88e1510_hwmon_probe(struct phy_device *phydev) { return marvell_hwmon_probe(phydev, &m88e1510_hwmon_chip_info); } #else static int m88e1121_hwmon_probe(struct phy_device *phydev) { return 0; } static int m88e1510_hwmon_probe(struct phy_device *phydev) { return 0; } #endif static int marvell_probe(struct phy_device *phydev) { struct marvell_priv *priv; priv = devm_kzalloc(&phydev->mdio.dev, sizeof(*priv), GFP_KERNEL); if (!priv) return -ENOMEM; phydev->priv = priv; return 0; } static int m88e1121_probe(struct phy_device *phydev) { int err; err = marvell_probe(phydev); if (err) return err; return m88e1121_hwmon_probe(phydev); } static int m88e1510_probe(struct phy_device *phydev) { int err; err = marvell_probe(phydev); if (err) return err; return m88e1510_hwmon_probe(phydev); } static struct phy_driver marvell_drivers[] = { { .phy_id = MARVELL_PHY_ID_88E1101, .phy_id_mask = MARVELL_PHY_ID_MASK, .name = "Marvell 88E1101", .features = PHY_GBIT_FEATURES, .flags = PHY_HAS_INTERRUPT, .probe = marvell_probe, .config_init = &marvell_config_init, .config_aneg = &marvell_config_aneg, .read_status = &genphy_read_status, .ack_interrupt = &marvell_ack_interrupt, .config_intr = &marvell_config_intr, .resume = &genphy_resume, .suspend = &genphy_suspend, .get_sset_count = marvell_get_sset_count, .get_strings = marvell_get_strings, .get_stats = marvell_get_stats, }, { .phy_id = MARVELL_PHY_ID_88E1112, .phy_id_mask = MARVELL_PHY_ID_MASK, .name = "Marvell 88E1112", .features = PHY_GBIT_FEATURES, .flags = PHY_HAS_INTERRUPT, .probe = marvell_probe, .config_init = &m88e1111_config_init, .config_aneg = &marvell_config_aneg, .read_status = &genphy_read_status, .ack_interrupt = &marvell_ack_interrupt, .config_intr = &marvell_config_intr, .resume = &genphy_resume, .suspend = &genphy_suspend, .get_sset_count = marvell_get_sset_count, .get_strings = marvell_get_strings, .get_stats = marvell_get_stats, }, { .phy_id = MARVELL_PHY_ID_88E1111, .phy_id_mask = MARVELL_PHY_ID_MASK, .name = "Marvell 88E1111", .features = PHY_GBIT_FEATURES, .flags = PHY_HAS_INTERRUPT, .probe = marvell_probe, .config_init = &m88e1111_config_init, .config_aneg = &m88e1111_config_aneg, .read_status = &marvell_read_status, .ack_interrupt = &marvell_ack_interrupt, .config_intr = &marvell_config_intr, .resume = &genphy_resume, .suspend = &genphy_suspend, .get_sset_count = marvell_get_sset_count, .get_strings = marvell_get_strings, .get_stats = marvell_get_stats, }, { .phy_id = MARVELL_PHY_ID_88E1118, .phy_id_mask = MARVELL_PHY_ID_MASK, .name = "Marvell 88E1118", .features = PHY_GBIT_FEATURES, .flags = PHY_HAS_INTERRUPT, .probe = marvell_probe, .config_init = &m88e1118_config_init, .config_aneg = &m88e1118_config_aneg, .read_status = &genphy_read_status, .ack_interrupt = &marvell_ack_interrupt, .config_intr = &marvell_config_intr, .resume = &genphy_resume, .suspend = &genphy_suspend, .get_sset_count = marvell_get_sset_count, .get_strings = marvell_get_strings, .get_stats = marvell_get_stats, }, { .phy_id = MARVELL_PHY_ID_88E1121R, .phy_id_mask = MARVELL_PHY_ID_MASK, .name = "Marvell 88E1121R", .features = PHY_GBIT_FEATURES, .flags = PHY_HAS_INTERRUPT, .probe = &m88e1121_probe, .config_init = &m88e1121_config_init, .config_aneg = &m88e1121_config_aneg, .read_status = &marvell_read_status, .ack_interrupt = &marvell_ack_interrupt, .config_intr = &marvell_config_intr, .did_interrupt = &m88e1121_did_interrupt, .resume = &genphy_resume, .suspend = &genphy_suspend, .get_sset_count = marvell_get_sset_count, .get_strings = marvell_get_strings, .get_stats = marvell_get_stats, }, { .phy_id = MARVELL_PHY_ID_88E1318S, .phy_id_mask = MARVELL_PHY_ID_MASK, .name = "Marvell 88E1318S", .features = PHY_GBIT_FEATURES, .flags = PHY_HAS_INTERRUPT, .probe = marvell_probe, .config_init = &m88e1121_config_init, .config_aneg = &m88e1318_config_aneg, .read_status = &marvell_read_status, .ack_interrupt = &marvell_ack_interrupt, .config_intr = &marvell_config_intr, .did_interrupt = &m88e1121_did_interrupt, .get_wol = &m88e1318_get_wol, .set_wol = &m88e1318_set_wol, .resume = &genphy_resume, .suspend = &genphy_suspend, .get_sset_count = marvell_get_sset_count, .get_strings = marvell_get_strings, .get_stats = marvell_get_stats, }, { .phy_id = MARVELL_PHY_ID_88E1145, .phy_id_mask = MARVELL_PHY_ID_MASK, .name = "Marvell 88E1145", .features = PHY_GBIT_FEATURES, .flags = PHY_HAS_INTERRUPT, .probe = marvell_probe, .config_init = &m88e1145_config_init, .config_aneg = &marvell_config_aneg, .read_status = &genphy_read_status, .ack_interrupt = &marvell_ack_interrupt, .config_intr = &marvell_config_intr, .resume = &genphy_resume, .suspend = &genphy_suspend, .get_sset_count = marvell_get_sset_count, .get_strings = marvell_get_strings, .get_stats = marvell_get_stats, }, { .phy_id = MARVELL_PHY_ID_88E1149R, .phy_id_mask = MARVELL_PHY_ID_MASK, .name = "Marvell 88E1149R", .features = PHY_GBIT_FEATURES, .flags = PHY_HAS_INTERRUPT, .probe = marvell_probe, .config_init = &m88e1149_config_init, .config_aneg = &m88e1118_config_aneg, .read_status = &genphy_read_status, .ack_interrupt = &marvell_ack_interrupt, .config_intr = &marvell_config_intr, .resume = &genphy_resume, .suspend = &genphy_suspend, .get_sset_count = marvell_get_sset_count, .get_strings = marvell_get_strings, .get_stats = marvell_get_stats, }, { .phy_id = MARVELL_PHY_ID_88E1240, .phy_id_mask = MARVELL_PHY_ID_MASK, .name = "Marvell 88E1240", .features = PHY_GBIT_FEATURES, .flags = PHY_HAS_INTERRUPT, .probe = marvell_probe, .config_init = &m88e1111_config_init, .config_aneg = &marvell_config_aneg, .read_status = &genphy_read_status, .ack_interrupt = &marvell_ack_interrupt, .config_intr = &marvell_config_intr, .resume = &genphy_resume, .suspend = &genphy_suspend, .get_sset_count = marvell_get_sset_count, .get_strings = marvell_get_strings, .get_stats = marvell_get_stats, }, { .phy_id = MARVELL_PHY_ID_88E1116R, .phy_id_mask = MARVELL_PHY_ID_MASK, .name = "Marvell 88E1116R", .features = PHY_GBIT_FEATURES, .flags = PHY_HAS_INTERRUPT, .probe = marvell_probe, .config_init = &m88e1116r_config_init, .config_aneg = &genphy_config_aneg, .read_status = &genphy_read_status, .ack_interrupt = &marvell_ack_interrupt, .config_intr = &marvell_config_intr, .resume = &genphy_resume, .suspend = &genphy_suspend, .get_sset_count = marvell_get_sset_count, .get_strings = marvell_get_strings, .get_stats = marvell_get_stats, }, { .phy_id = MARVELL_PHY_ID_88E1510, .phy_id_mask = MARVELL_PHY_ID_MASK, .name = "Marvell 88E1510", .features = PHY_GBIT_FEATURES | SUPPORTED_FIBRE, .flags = PHY_HAS_INTERRUPT, .probe = &m88e1510_probe, .config_init = &m88e1510_config_init, .config_aneg = &m88e1510_config_aneg, .read_status = &marvell_read_status, .ack_interrupt = &marvell_ack_interrupt, .config_intr = &marvell_config_intr, .did_interrupt = &m88e1121_did_interrupt, .get_wol = &m88e1318_get_wol, .set_wol = &m88e1318_set_wol, .resume = &marvell_resume, .suspend = &marvell_suspend, .get_sset_count = marvell_get_sset_count, .get_strings = marvell_get_strings, .get_stats = marvell_get_stats, }, { .phy_id = MARVELL_PHY_ID_88E1540, .phy_id_mask = MARVELL_PHY_ID_MASK, .name = "Marvell 88E1540", .features = PHY_GBIT_FEATURES, .flags = PHY_HAS_INTERRUPT, .probe = m88e1510_probe, .config_init = &marvell_config_init, .config_aneg = &m88e1510_config_aneg, .read_status = &marvell_read_status, .ack_interrupt = &marvell_ack_interrupt, .config_intr = &marvell_config_intr, .did_interrupt = &m88e1121_did_interrupt, .resume = &genphy_resume, .suspend = &genphy_suspend, .get_sset_count = marvell_get_sset_count, .get_strings = marvell_get_strings, .get_stats = marvell_get_stats, }, { .phy_id = MARVELL_PHY_ID_88E1545, .phy_id_mask = MARVELL_PHY_ID_MASK, .name = "Marvell 88E1545", .probe = m88e1510_probe, .features = PHY_GBIT_FEATURES, .flags = PHY_HAS_INTERRUPT, .config_init = &marvell_config_init, .config_aneg = &m88e1510_config_aneg, .read_status = &marvell_read_status, .ack_interrupt = &marvell_ack_interrupt, .config_intr = &marvell_config_intr, .did_interrupt = &m88e1121_did_interrupt, .resume = &genphy_resume, .suspend = &genphy_suspend, .get_sset_count = marvell_get_sset_count, .get_strings = marvell_get_strings, .get_stats = marvell_get_stats, }, { .phy_id = MARVELL_PHY_ID_88E3016, .phy_id_mask = MARVELL_PHY_ID_MASK, .name = "Marvell 88E3016", .features = PHY_BASIC_FEATURES, .flags = PHY_HAS_INTERRUPT, .probe = marvell_probe, .config_aneg = &genphy_config_aneg, .config_init = &m88e3016_config_init, .aneg_done = &marvell_aneg_done, .read_status = &marvell_read_status, .ack_interrupt = &marvell_ack_interrupt, .config_intr = &marvell_config_intr, .did_interrupt = &m88e1121_did_interrupt, .resume = &genphy_resume, .suspend = &genphy_suspend, .get_sset_count = marvell_get_sset_count, .get_strings = marvell_get_strings, .get_stats = marvell_get_stats, }, { .phy_id = MARVELL_PHY_ID_88E6390, .phy_id_mask = MARVELL_PHY_ID_MASK, .name = "Marvell 88E6390", .features = PHY_GBIT_FEATURES, .flags = PHY_HAS_INTERRUPT, .probe = m88e1510_probe, .config_init = &marvell_config_init, .config_aneg = &m88e1510_config_aneg, .read_status = &marvell_read_status, .ack_interrupt = &marvell_ack_interrupt, .config_intr = &marvell_config_intr, .did_interrupt = &m88e1121_did_interrupt, .resume = &genphy_resume, .suspend = &genphy_suspend, .get_sset_count = marvell_get_sset_count, .get_strings = marvell_get_strings, .get_stats = marvell_get_stats, }, }; module_phy_driver(marvell_drivers); static struct mdio_device_id __maybe_unused marvell_tbl[] = { { MARVELL_PHY_ID_88E1101, MARVELL_PHY_ID_MASK }, { MARVELL_PHY_ID_88E1112, MARVELL_PHY_ID_MASK }, { MARVELL_PHY_ID_88E1111, MARVELL_PHY_ID_MASK }, { MARVELL_PHY_ID_88E1118, MARVELL_PHY_ID_MASK }, { MARVELL_PHY_ID_88E1121R, MARVELL_PHY_ID_MASK }, { MARVELL_PHY_ID_88E1145, MARVELL_PHY_ID_MASK }, { MARVELL_PHY_ID_88E1149R, MARVELL_PHY_ID_MASK }, { MARVELL_PHY_ID_88E1240, MARVELL_PHY_ID_MASK }, { MARVELL_PHY_ID_88E1318S, MARVELL_PHY_ID_MASK }, { MARVELL_PHY_ID_88E1116R, MARVELL_PHY_ID_MASK }, { MARVELL_PHY_ID_88E1510, MARVELL_PHY_ID_MASK }, { MARVELL_PHY_ID_88E1540, MARVELL_PHY_ID_MASK }, { MARVELL_PHY_ID_88E1545, MARVELL_PHY_ID_MASK }, { MARVELL_PHY_ID_88E3016, MARVELL_PHY_ID_MASK }, { MARVELL_PHY_ID_88E6390, MARVELL_PHY_ID_MASK }, { } }; MODULE_DEVICE_TABLE(mdio, marvell_tbl);