All arches do essentially the same thing now for
early_init_dt_setup_initrd_arch, so it can now be removed.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Convert c6x to use new early_init_dt_scan function.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: linux-c6x-dev@linux-c6x.org
Save some pointless copying of the kernel command line and just use
boot_command_line instead.
Also remove default_command_line as it is not referenced anywhere, and
the DT code already handles the default command line.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Tested-by: Mark Salter <msalter@redhat.com>
Acked-by: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: linux-c6x-dev@linux-c6x.org
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Most architectures use the same implementation. Collapse the common ones
into a single weak function that can be overridden.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
On some PAE architectures, the entire range of physical memory could reside
outside the 32-bit limit. These systems need the ability to specify the
initrd location using 64-bit numbers.
This patch globally modifies the early_init_dt_setup_initrd_arch() function to
use 64-bit numbers instead of the current unsigned long.
There has been quite a bit of debate about whether to use u64 or phys_addr_t.
It was concluded to stick to u64 to be consistent with rest of the device
tree code. As summarized by Geert, "The address to load the initrd is decided
by the bootloader/user and set at that point later in time. The dtb should not
be tied to the kernel you are booting"
More details on the discussion can be found here:
https://lkml.org/lkml/2013/6/20/690https://lkml.org/lkml/2012/9/13/544
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
This is the basic devicetree support for C6X. Currently, four boards are
supported. Each one uses a different SoC part. Two of the four supported
SoCs are multicore. One with 3 cores and the other with 6 cores. There is
no coherency between the core-level caches, so SMP is not an option. It is
possible to run separate kernel instances on the various cores. There is
currently no C6X bootloader support for device trees so we build in the DTB
for now.
There are some interesting twists to the hardware which are of note for device
tree support. Each core has its own interrupt controller which is controlled
by special purpose core registers. This core controller provides 12 general
purpose prioritized interrupt sources. Each core is contained within a
hardware "module" which provides L1 and L2 caches, power control, and another
interrupt controller which cascades into the core interrupt controller. These
core module functions are controlled by memory mapped registers. The addresses
for these registers are the same for each core. That is, when coreN accesses
a module-level MMIO register at a given address, it accesses the register for
coreN even though other cores would use the same address to access the register
in the module containing those cores. Other hardware modules (timers, enet, etc)
which are memory mapped can be accessed by all cores.
The timers need some further explanation for multicore SoCs. Even though all
timer control registers are visible to all cores, interrupt routing or other
considerations may make a given timer more suitable for use by a core than
some other timer. Because of this and the desire to have the same image run
on more than one core, the timer nodes have a "ti,core-mask" property which
is used by the driver to scan for a suitable timer to use.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Aurelien Jacquiot <a-jacquiot@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Rob Herring