AM654 base board does not have any PCIe slots. Disable all the
SERDES and PCIe instances.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add mux-controller DT node as a child node of scm_conf. This is
required for muxing SERDES between USB, PCIe and ICSS2 SGMII.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
GIC_ITS used in AM654 platform has the same configuration as that of
GIC_ITS used in Socionext SoCs. Add "socionext,synquacer-pre-its"
property to get PCI MSI working.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add the MSCM RAM address space to the ranges property of the cbass_main
interconnect node so that the addresses can be translated properly.
This fixes the probe failure in the sram driver for the MSMC RAM node.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add the address spaces for the R5F cores in MCU domain to the ranges
property of the cbass_mcu interconnect node so that the addresses
within the R5F nodes can be translated properly by the relevant OF
address API.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add the on-chip SRAM present within the MCU domain as a mmio-sram node.
The K3 AM65x SoCs have 512 KB of such memory. Any specific memory range
within this RAM needed by a software module ought to be reserved using
an appropriate child node.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add the address space for the MCU SRAM memory to the ranges property
of the cbass_mcu interconnect node so that the addresses within the
mcu_sram nodes and its children can be translated properly by the
relevant OF address API.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
There are 2 push buttons: SW5 and SW6 that are basically connected to
WKUP_GPIO0_24 and WKUP_GPIO0_27 respectively. Add the respective
nodes and the pinctrl data to set the mode to GPIO and Input.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add gpio0/1 nodes under main domain. They have 96 and 90 gpios
respectively and all are capable of generating banked interrupts.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add gpio0 node under wakeup domain. This has 56 gpios
and all are capable of generating banked interrupts.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Wakeup domain in AM654 SoC has an interrupt router connected to gpio
in wakeup domain. Add DT node for this interrupt router.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Main domain in AM654 has the following interrupt controller instances:
- Main Domain GPIO Interrupt router connected to gpio in main domain.
- Under the Main Domain Navigator Subsystem(NAVSS)
- Main Navss Interrupt Router connected to main navss inta and mailboxes.
- Main Navss Interrupt Aggregator connected to main domain UDMASS
Add DT nodes for the above three interrupt controllers available
in main domain.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Use the am654 specific compatible for dmsc. This allows to use
the am654 specific RM mapping table.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
changes for 5.3, please pull the following:
- Jim adds the ability for ARCH_BRCMSTB to use reset controllers
- Doug adds the ability for ARCH_BRCMSTB to use the PINCTRL framework
- Florian enables the use of the BCM7038 Level 1 interrupt controller
for ARCH_BRCMSTB
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEm+Rq3+YGJdiR9yuFh9CWnEQHBwQFAl0AZVIACgkQh9CWnEQH
BwRpqQ//VPkky+lI2lFZZC6t36T1mbVNLjvV2Ncl3VH6csJPN/lAHaSxp7IMpsjz
OkrOJ2oVUZ2N+0owP2NcWswzDgO00EEozt2q2zmP7KJQN0f1SLdA/edcEUTv0J1Z
rLoLRYNPp0B3JJDXZ84+YKFiboYsAypYkoWNawSZg2jWYhHIY8r6yU81HIrqzInV
vWAoOCfW1DXUtI9/tjsBoYv34Q2XR/CNfBjJ4MGem6QDASDIXw3ZkSMqEK4LzZT8
sFA4ZrkiNmdTK9HE0eOkEAHryAWtBglJxxt0rsGuzUvecp3uqZqN3NqxonGHKGh0
R6SOVOSDb1rp+PFeSFVFpduDCxXL7oB+/CpEMtHDShq7kF8IoctlxFWDFJHE0i1m
cyPKQbi4tYlN8VtGIg7FAIn1UEJcSpJxwKPlk539VpjWIcHKFhP21+9b925YGjj9
L38Ef6Fba4znzE9T+yzO8NyAhQWtjIeTe6vQwKKIvxLIi1T4V1jCqk+TppOTegk8
zTp/GBtOYMvpTxvY0DpDo09FHuVvyM2Akz5vIw0hbhWyHe1KXRPZ8epXcWP7yOjr
9En1O0pAzKGSEbueBsq5aR+/kfAEXeXtdjV8/n9vAUSWdYrBwmlrUvAnVg27ynSz
FSKxEXM7lgm7KZpC77jFNTgCuak3FPcXwYefHw1z3iHVfiBgMeE=
=LQ38
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.3/soc-arm64' of https://github.com/Broadcom/stblinux into arm/soc
This pull request contains Broadcom ARM64-based SoCs Kconfig.platform
changes for 5.3, please pull the following:
- Jim adds the ability for ARCH_BRCMSTB to use reset controllers
- Doug adds the ability for ARCH_BRCMSTB to use the PINCTRL framework
- Florian enables the use of the BCM7038 Level 1 interrupt controller
for ARCH_BRCMSTB
* tag 'arm-soc/for-5.3/soc-arm64' of https://github.com/Broadcom/stblinux:
arm64: Enable PINCTRL for ARCH_BRCMSTB
arm64: Enable ARCH_HAS_RESET_CONTROLLER for ARCH_BRCMSTB
arm64: Enable BCM7038_L1_IRQ for ARCH_BRCMSTB
Signed-off-by: Olof Johansson <olof@lixom.net>
If the cache line size is greater than ARCH_DMA_MINALIGN (128),
the warning shows and it's tainted as TAINT_CPU_OUT_OF_SPEC.
However, it's not good because as discussed in the thread [1], the cpu
cache line size will be problem only on non-coherent devices.
Since the coherent flag is already introduced to struct device,
show the warning only if the device is non-coherent device and
ARCH_DMA_MINALIGN is smaller than the cpu cache size.
[1] https://lore.kernel.org/linux-arm-kernel/20180514145703.celnlobzn3uh5tc2@localhost/
Signed-off-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Tested-by: Zhang Lei <zhang.lei@jp.fujitsu.com>
[catalin.marinas@arm.com: removed 'if' block for WARN_TAINT]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add USB 2.0 support to the HiHope RZ/G2M.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Similarly to what done for the r8a7796 with commit 737e05bf03
("arm64: dts: renesas: revise properties for R-Car Gen3 SoCs'
usb 2.0"), this patch lists the clock for the USB High-Speed Module
(HS-USB) with the USB2.0 Host (EHCI/OHCI) IP DT node, and it lists
the clock for the USB2.0 Host IP with the HS-USB module DT node.
Fixes: 4c2c2fb998 ("arm64: dts: renesas: r8a774a1: Add USB2.0 phy and host(EHCI/OHCI) device nodes")
Fixes: ed898d4fc1 ("arm64: dts: renesas: r8a774a1: Add USB-DMAC and HSUSB device nodes")
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
- Fix up a Kbuild warning when SOC_TI is not set
-----BEGIN PGP SIGNATURE-----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=Guww
-----END PGP SIGNATURE-----
Merge tag 'am654-fixes-for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux into fixes
Texas Instruments AM65x fixes for v5.2
- Fix up a Kbuild warning when SOC_TI is not set
* tag 'am654-fixes-for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux:
arm64: arch_k3: Fix kconfig dependency warning
Signed-off-by: Olof Johansson <olof@lixom.net>
- A build fix for soc-imx8 driver which needs SOC_BUS support. To
avoid dealing with the dependency for every single i.MX SoC bus
driver, we selects at from architecture level.
- A fix on i.MX SCU firmware driver to ensure SCU irq is enabled only
after IPC is ready.
- A regression fix on cpuidle-imx6sx driver, which causes some
characters loss on serial communication.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJc50FAAAoJEFBXWFqHsHzOt4wIAJJ4MLXCMKj2oVWXimkF3DAF
g9M7ridrarhPAXowuTYV4FuW7me7nPxr5VTmwVIJE23wEKdaOd7cg0tkmvMi0tG6
3TlNwCsEjJx+9rtGF196SZfR9HinLziAc4x7Qcl88xlQTQEIptvx6AMPit7Gy0je
MJ0PzLA1l+tazo7dXvMjZ+LkxlvLTSB/RuBciA8sgOvwsdbG1Azz/AduSLxO7e/T
ZSmEElTluqIKVxH5sbVY0T7mxWat7l5As28nx27cWDHGPoDMOt/TWiCTAvFR0d6T
m+bW6xcvy63Z2II1Er//ig4rwcmK1mcUv+3i63/sIkFxl9fa0H4WnTu67T+/mck=
=zbC7
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 5.2:
- A build fix for soc-imx8 driver which needs SOC_BUS support. To
avoid dealing with the dependency for every single i.MX SoC bus
driver, we selects at from architecture level.
- A fix on i.MX SCU firmware driver to ensure SCU irq is enabled only
after IPC is ready.
- A regression fix on cpuidle-imx6sx driver, which causes some
characters loss on serial communication.
* tag 'imx-fixes-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: cpuidle-imx6sx: Restrict the SW2ISO increase to i.MX6SX
firmware: imx: SCU irq should ONLY be enabled after SCU IPC is ready
arm64: imx: Fix build error without CONFIG_SOC_BUS
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch is to add ptp timer device tree node for dpaa2
platforms(ls1088a/ls208xa/lx2160a).
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable the sound card on the X96 Max, enabling HDMI output using the
TDM interface B, being aligned on other boards sound cards.
SPDI/F support is also enabled to the physical toslink port and to HDMI.
The internal DAC connected to the audio jack will be added later on, when
driver support is added.
Tested by running:
tinymix set "FRDDR_A SRC 1 EN Switch" 1
tinymix set "FRDDR_A SINK 1 SEL" "OUT 1"
tinymix set "FRDDR_B SRC 1 EN Switch" 1
tinymix set "FRDDR_B SINK 1 SEL" "OUT 1"
tinymix set "FRDDR_C SRC 1 EN Switch" 1
tinymix set "FRDDR_C SINK 1 SEL" "OUT 1"
tinymix set "TOHDMITX I2S SRC" "I2S B"
tinymix set "TOHDMITX Switch" 1
then:
tinymix set "TDMOUT_B SRC SEL" "IN 0"
speaker-test -Dhw:0,0 -c2
then:
tinymix set "TDMOUT_B SRC SEL" "IN 1"
speaker-test -Dhw:0,1 -c2
then:
tinymix set "TDMOUT_B SRC SEL" "IN 2"
speaker-test -Dhw:0,2 -c2
testing HDMI audio output from the all 3 ASoC playback interfaces.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the sound card on the Hardkernel Odroid-N2, enabling HDMI output
using the TDM interface B, being aligned on other boards sound cards.
The internal DAC connected to the audio jack will be added later on, when
driver support is added.
Tested by running:
tinymix set "FRDDR_A SRC 1 EN Switch" 1
tinymix set "FRDDR_A SINK 1 SEL" "OUT 1"
tinymix set "FRDDR_B SRC 1 EN Switch" 1
tinymix set "FRDDR_B SINK 1 SEL" "OUT 1"
tinymix set "FRDDR_C SRC 1 EN Switch" 1
tinymix set "FRDDR_C SINK 1 SEL" "OUT 1"
tinymix set "TOHDMITX I2S SRC" "I2S B"
tinymix set "TOHDMITX Switch" 1
then:
tinymix set "TDMOUT_B SRC SEL" "IN 0"
speaker-test -Dhw:0,0 -c2
then:
tinymix set "TDMOUT_B SRC SEL" "IN 1"
speaker-test -Dhw:0,1 -c2
then:
tinymix set "TDMOUT_B SRC SEL" "IN 2"
speaker-test -Dhw:0,2 -c2
testing HDMI audio output from the all 3 ASoC playback interfaces.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the sound card on the sei510:
* TDM interface A is connected to an external DAC and a speaker installed
on the device.
* HDMI is expected to use TDM B. It can also use TDM A but will be
limited to 2 channels, as accepted by the external DAC.
* 2 Built in PDM mics through the PDM interface.
* Both TDM outputs may use HW loopback.
The internal DAC connected to audio jack will be added later on, when
driver support is added.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The SEI510 board features a max98357a audio codec for built-in
speaker
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Convert kdump documentation to ReST and add it to the
user faced manual, as the documents are mainly focused on
sysadmins that would be enabling kdump.
Note: the vmcoreinfo.rst has one very long title on one of its
sub-sections:
PG_lru|PG_private|PG_swapcache|PG_swapbacked|PG_slab|PG_hwpoision|PG_head_mask|PAGE_BUDDY_MAPCOUNT_VALUE(~PG_buddy)|PAGE_OFFLINE_MAPCOUNT_VALUE(~PG_offline)
I opted to break this one, into two entries with the same content,
in order to make it easier to display after being parsed in html and PDF.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The documentation is in a format that is very close to ReST format.
The conversion is actually:
- add blank lines in order to identify paragraphs;
- fixing tables markups;
- adding some lists markups;
- marking literal blocks;
- adjust some title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlz8fAYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG1asH/3ySguxqtqL1MCBa
4/SZ37PHeWKMerfX6ZyJdgEqK3B+PWlmuLiOMNK5h2bPLzeQQQAmHU/mfKmpXqgB
dHwUbG9yNnyUtTfsfRqAnCA6vpuw9Yb1oIzTCVQrgJLSWD0j7scBBvmzYqguOkto
ThwigLUq3AILr8EfR4rh+GM+5Dn9OTEFAxwil9fPHQo7QoczwZxpURhScT6Co9TB
DqLA3fvXbBvLs/CZy/S5vKM9hKzC+p39ApFTURvFPrelUVnythAM0dPDJg3pIn5u
g+/+gDxDFa+7ANxvxO2ng1sJPDqJMeY/xmjJYlYyLpA33B7zLNk2vDHhAP06VTtr
XCMhQ9s=
=cb80
-----END PGP SIGNATURE-----
Merge tag 'v5.2-rc4' into mauro
We need to pick up post-rc1 changes to various document files so they don't
get lost in Mauro's massive RST conversion push.
- Fix broken SVE ptrace API when running in a big-endian configuration
- Fix performance regression due to off-by-one in TLBI range checking
- Fix build regression when using Clang
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAl0DsZ0ACgkQt6xw3ITB
YzRE3wf9GJibmSnm9q5gmtHcKMrH+atXrI93nyzhBZxYaAYAKSiz7RCMSpc7iudI
bGMruaaqn/2xrdOie3vOOfSqFfzrfcFOuh/0id9R2IyiFSg08BrI369buejNRtm+
BUhdUQCe5p5afJ7PYFa7CYD+tSC1WiHXfOhH6sRYllerwaMiR9y/eqf3Gh5zB26Q
ca/+2Jh59DxXIpSWP9nTzPyV9xKOJ1B8JdMR5BMIUnOgUXQhMwNeuivRrZnEG9yT
PZDGbk5WxKci+LHPOt7stFFuo7hZn3SCKJ0mZ20VUs0w7ETMJuI0Ss4TlE2mgYag
TASmsypuLdRz5mxIeyY5QYXppSyYiA==
=AhWz
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Here are some arm64 fixes for -rc5.
The only non-trivial change (in terms of the diffstat) is fixing our
SVE ptrace API for big-endian machines, but the majority of this is
actually the addition of much-needed comments and updates to the
documentation to try to avoid this mess biting us again in future.
There are still a couple of small things on the horizon, but nothing
major at this point.
Summary:
- Fix broken SVE ptrace API when running in a big-endian configuration
- Fix performance regression due to off-by-one in TLBI range checking
- Fix build regression when using Clang"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64/sve: Fix missing SVE/FPSIMD endianness conversions
arm64: tlbflush: Ensure start/end of address range are aligned to stride
arm64: Don't unconditionally add -Wno-psabi to KBUILD_CFLAGS
Tegra186 board under arm64 is using this device, according to
its dts file. So this patch enables its driver with a "=m" as
the other HWMON drivers.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Due to an integration issue the architected timer on Tegra210 does not
remain on during system suspend (a.k.a. SC7). Mark it accordingly so
that it isn't considered as a means to track suspend time.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The architected timer on Tegra186 and Tegra194 is in an always on power
partition and its reference clock will always run, so mark the timer as
always on.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add devicetree support for Khadas Edge/Edge-V/Captain boards.
Khadas Edge is an expandable Rockchip RK3399 board with goldfinger.
Khadas Captain is the carrier board for Khadas Edge.
Khadas Edge-V is a Khadas VIM form factor Rockchip RK3399 board.
Signed-off-by: Nick Xie <nick@khadas.com>
[edge-captain and edge-v contain different components that are supposed
to get added in future patches, so should stay separate while looking
somewhat similar right now]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
'default n' is the default value for any bool or tristate Kconfig
setting so there is no need to write it explicitly.
Also since commit f467c5640c ("kconfig: only write '# CONFIG_FOO
is not set' for visible symbols") the Kconfig behavior is the same
regardless of 'default n' being present or not:
...
One side effect of (and the main motivation for) this change is making
the following two definitions behave exactly the same:
config FOO
bool
config FOO
bool
default n
With this change, neither of these will generate a
'# CONFIG_FOO is not set' line (assuming FOO isn't selected/implied).
That might make it clearer to people that a bare 'default n' is
redundant.
...
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This commit enables the hdmi-sound device needed to have
audio over HDMI on the Rock Pi board.
Fixes: 1b5715c602 ("arm64: dts: rockchip: add ROCK Pi 4 DTS support")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The in-memory representation of SVE and FPSIMD registers is
different: the FPSIMD V-registers are stored as single 128-bit
host-endian values, whereas SVE registers are stored in an
endianness-invariant byte order.
This means that the two representations differ when running on a
big-endian host. But we blindly copy data from one representation
to another when converting between the two, resulting in the
register contents being unintentionally byteswapped in certain
situations. Currently this can be triggered by the first SVE
instruction after a syscall, for example (though the potential
trigger points may vary in future).
So, fix the conversion functions fpsimd_to_sve(), sve_to_fpsimd()
and sve_sync_from_fpsimd_zeropad() to swab where appropriate.
There is no common swahl128() or swab128() that we could use here.
Maybe it would be worth making this generic, but for now add a
simple local hack.
Since the byte order differences are exposed in ABI, also clarify
the documentation.
Cc: Alex Bennée <alex.bennee@linaro.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Alan Hayward <alan.hayward@arm.com>
Cc: Julien Grall <julien.grall@arm.com>
Fixes: bc0ee47603 ("arm64/sve: Core task context handling")
Fixes: 8cd969d28f ("arm64/sve: Signal handling support")
Fixes: 43d4da2c45 ("arm64/sve: ptrace and ELF coredump support")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
[will: Fix typos in comments and docs spotted by Julien]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Constify the ctx and iv arguments to crypto_chacha_init() and the
various chacha*_stream_xor() functions. This makes it clear that they
are not modified.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Since commit 3d65b6bbc0 ("arm64: tlbi: Set MAX_TLBI_OPS to
PTRS_PER_PTE"), we resort to per-ASID invalidation when attempting to
perform more than PTRS_PER_PTE invalidation instructions in a single
call to __flush_tlb_range(). Whilst this is beneficial, the mmu_gather
code does not ensure that the end address of the range is rounded-up
to the stride when freeing intermediate page tables in pXX_free_tlb(),
which defeats our range checking.
Align the bounds passed into __flush_tlb_range().
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Reported-by: Hanjun Guo <guohanjun@huawei.com>
Tested-by: Hanjun Guo <guohanjun@huawei.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Since commit d26c25a9d1 ("arm64: KVM: Tighten guest core register
access from userspace"), KVM_{GET,SET}_ONE_REG rejects register IDs
that do not correspond to a single underlying architectural register.
KVM_GET_REG_LIST was not changed to match however: instead, it
simply yields a list of 32-bit register IDs that together cover the
whole kvm_regs struct. This means that if userspace tries to use
the resulting list of IDs directly to drive calls to KVM_*_ONE_REG,
some of those calls will now fail.
This was not the intention. Instead, iterating KVM_*_ONE_REG over
the list of IDs returned by KVM_GET_REG_LIST should be guaranteed
to work.
This patch fixes the problem by splitting validate_core_offset()
into a backend core_reg_size_from_offset() which does all of the
work except for checking that the size field in the register ID
matches, and kvm_arm_copy_reg_indices() and num_core_regs() are
converted to use this to enumerate the valid offsets.
kvm_arm_copy_reg_indices() now also sets the register ID size field
appropriately based on the value returned, so the register ID
supplied to userspace is fully qualified for use with the register
access ioctls.
Cc: stable@vger.kernel.org
Fixes: d26c25a9d1 ("arm64: KVM: Tighten guest core register access from userspace")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Tested-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This routine is a one-liner and doesn't really need to be function and
can be implemented as a macro.
Suggested-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
H6 has DMA controller which supports 16 channels.
Add a node for it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This patch adds TMU[01234] device tree nodes to the r8a774a1
SoC specific DT.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds the CMT[0123] device tree nodes to the
r8a774a1 SoC specific DT.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds uSD and eMMC support to the HiHope RZ/G2M
board.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since the R8A77990 SoC uses DU{0,1}, the range from the base address to
the 0x4000 address is used.
This patch fixed it.
Fixes: 13ee2bfc54 ("arm64: dts: renesas: r8a77990: Add display output support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables TI HD3SS3220 device and support usb role switch
for the CAT 874 platform.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables USB3.0 host/peripheral device node for the cat874
board.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable support for the TI HD3SS320 USB Type-C DRP Port controller driver
by turning on CONFIG_TYPEC and CONFIG_TYPEC_HD3SS3220 as modules.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the new renesas,companion property to the LVDS0 node to point to the
companion LVDS encoder LVDS1.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable RWDT and use 60 seconds as default timeout.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables PCIEC[01] PCI express controller on the sub board.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Declare pcie bus clock, since it is generated on the HiHope RZ/G2M main
board.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This is a GCC only option, which warns about ABI changes within GCC, so
unconditionally adding it breaks Clang with tons of:
warning: unknown warning option '-Wno-psabi' [-Wunknown-warning-option]
and link time failures:
ld.lld: error: undefined symbol: __efistub___stack_chk_guard
>>> referenced by arm-stub.c:73
(/home/nathan/cbl/linux/drivers/firmware/efi/libstub/arm-stub.c:73)
>>> arm-stub.stub.o:(__efistub_install_memreserve_table)
in archive ./drivers/firmware/efi/libstub/lib.a
These failures come from the lack of -fno-stack-protector, which is
added via cc-option in drivers/firmware/efi/libstub/Makefile. When an
unknown flag is added to KBUILD_CFLAGS, clang will noisily warn that it
is ignoring the option like above, unlike gcc, who will just error.
$ echo "int main() { return 0; }" > tmp.c
$ clang -Wno-psabi tmp.c; echo $?
warning: unknown warning option '-Wno-psabi' [-Wunknown-warning-option]
1 warning generated.
0
$ gcc -Wsometimes-uninitialized tmp.c; echo $?
gcc: error: unrecognized command line option
‘-Wsometimes-uninitialized’; did you mean ‘-Wmaybe-uninitialized’?
1
For cc-option to work properly with clang and behave like gcc, -Werror
is needed, which was done in commit c3f0d0bc5b ("kbuild, LLVMLinux:
Add -Werror to cc-option to support clang").
$ clang -Werror -Wno-psabi tmp.c; echo $?
error: unknown warning option '-Wno-psabi'
[-Werror,-Wunknown-warning-option]
1
As a consequence of this, when an unknown flag is unconditionally added
to KBUILD_CFLAGS, it will cause cc-option to always fail and those flags
will never get added:
$ clang -Werror -Wno-psabi -fno-stack-protector tmp.c; echo $?
error: unknown warning option '-Wno-psabi'
[-Werror,-Wunknown-warning-option]
1
This can be seen when compiling the whole kernel as some warnings that
are normally disabled (see below) show up. The full list of flags
missing from drivers/firmware/efi/libstub are the following (gathered
from diffing .arm64-stub.o.cmd):
-fno-delete-null-pointer-checks
-Wno-address-of-packed-member
-Wframe-larger-than=2048
-Wno-unused-const-variable
-fno-strict-overflow
-fno-merge-all-constants
-fno-stack-check
-Werror=date-time
-Werror=incompatible-pointer-types
-ffreestanding
-fno-stack-protector
Use cc-disable-warning so that it gets disabled for GCC and does nothing
for Clang.
Fixes: ebcc5928c5 ("arm64: Silence gcc warnings about arch ABI drift")
Link: https://github.com/ClangBuiltLinux/linux/issues/511
Reported-by: Qian Cai <cai@lca.pw>
Acked-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
MDSS and its friends complain about the DTS is using legacy clock names,
update these to silence the warnings.
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The current entry-latency-us is too short.
The proper way to convert between the device tree properties
from the vendor tree to the upstream PSCI device tree properties is:
entry-latency-us = qcom,time-overhead - qcom,latency-us
which gives
entry-latency-us = 210 - 80 = 130
Fixes: f6aee7af59 ("arm64: dts: qcom: msm8996: Add PSCI cpuidle low power states")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
PSCI spec define 1st parameter's bit 16 of function CPU_SUSPEND to
indicate CPU State Type: 0 for standby, 1 for power down. In this
case, we want to select standby for CPU idle feature. But current
setting wrongly select power down and cause CPU SUSPEND fail every
time. Need this fix.
Fixes: 8897f3255c ("arm64: dts: Add support for NXP LS1028A SoC")
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add device bindings for cpuidle states for cpu devices.
[marc: rebase, fix arm,psci-suspend-param, fix entry-latency-us]
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The AOSS QMP provides a number of power domains, used for QDSS and
PIL, add the node for this.
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
GPIO interrupts are used for the external Ethernet RGMII PHY interrupt
line.
Add the GPIO interrupt controller so we can describe that connection in
the dts files.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Setting to 2Mbaud/s is the nominal bus speed for common usages.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Setting to 2Mbaud/s is the nominal bus speed for common usages.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The 32k low power clock is necessary for the bluetooth part of the
combo module to initialize correctly, simply add the same clock we
use for the sdio pwrseq.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The 32k low power clock is necessary for the bluetooth part of the
combo module to initialize correctly, simply add the same clock we
use for the sdio pwrseq.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The SEI510 embeds an AP6398S SDIO module, let's add the
corresponding SDIO, PWM clock and mmc-pwrseq nodes.
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The X96 Max embeds an AP6398S SDIO module, let's add the
corresponding SDIO, PWM clock and mmc-pwrseq nodes.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add nodes to support SDCard and onboard eMMC on the X96 Max.
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Amlogic G12A SDIO Controller has a bug preventing direct DDR access,
add the port A (SDIO) pinctrl and controller nodes and mark this specific
controller with the amlogic,dram-access-quirk property.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch adds basic support for :
- Amlogic G12B, which is very similar to G12A
- The HardKernel Odroid-N2 based on the S922X SoC
The Amlogic G12B SoC is very similar with the G12A SoC, sharing
most of the features and architecture, but with these differences :
- The first CPU cluster only has 2xCortex-A53 instead of 4
- G12B has a second cluster of 4xCortex-A73
- Both cluster can achieve 2GHz instead of 1,8GHz for G12A
- CPU Clock architecture is difference, thus needing a different
compatible to handle this slight difference
- Supports a MIPI CSI input
- Embeds a Mali-G52 instead of a Mali-G31, but integration is the same
Actual support is done in the same way as for the GXM support, including
the G12A dtsi and redefining the CPU clusters.
Unlike GXM, the first cluster is different, thus needing to remove
the last 2 cpu nodes of the first cluster.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
[khilman: add vin-supply for vcc_v5 as suggested by Anand Moon]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the external ethernet PHY interrupt on the Vega S95 board.
Suggested-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Fix the SDIO WiFi support and add proper Bluetooth support on the
Vega S95 board.
Suggested-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add SARARC node and associated regulator to support reading the
ADC inputs on the Vega S95
Suggested-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add CEC nodes to support CEC communication on Vega S95
Suggested-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add HDMI nodes to support graphics on Vega S95
Suggested-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Align the regulator names with other GXBB SoCS for upcoming
SARADC support and SDIO/SDCard fixes.
Also fix how regulators are passed to MMC controllers & USB.
Suggested-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This enables Bluetooth support for the following models:
AP6335 in the WeTek Hub rev1 - BCM4335C0.hcd
AP6255 in the WeTek Hub rev2 - BCM4345C0.hcd
AP6330 in the WeTek Play 2 - BCM4330B1.hcd
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable SARADC on Wetek Boards.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
- Remove serial1 alias
- Add support for uart_A rts/cts
- Add bluetooth uart_A subnode qith shutdown gpio
Fixes: b8b74dda39 ("ARM64: dts: meson-gxm: Add support for Khadas VIM2")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Fix DTC warnings:
meson-gxm-khadas-vim2.dtb: Warning (avoid_unnecessary_addr_size):
/gpio-keys-polled: unnecessary #address-cells/#size-cells
without "ranges" or child "reg" property
Fixes: b8b74dda39 ("ARM64: dts: meson-gxm: Add support for Khadas VIM2")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the network interface of the X96 Mac using an external
Realtek RTL8211F gigabit PHY, needing the same broken-eee properties
as the previous Amlogic SoC generations.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Amlogic G12A has the hwrng module at the end of an unknown
"EFUSE" bus.
The hwrng is not enabled on the vendor G12A DTs, but is enabled on
next generation SM1 SoC family sharing the exact same memory mapping.
Let's add the "EFUSE" bus and the hwrng node.
This hwrng has been checked with the rng-tools rngtest FIPS tool :
rngtest: starting FIPS tests...
rngtest: bits received from input: 1630240032
rngtest: FIPS 140-2 successes: 81436
rngtest: FIPS 140-2 failures: 76
rngtest: FIPS 140-2(2001-10-10) Monobit: 10
rngtest: FIPS 140-2(2001-10-10) Poker: 6
rngtest: FIPS 140-2(2001-10-10) Runs: 26
rngtest: FIPS 140-2(2001-10-10) Long run: 34
rngtest: FIPS 140-2(2001-10-10) Continuous run: 0
rngtest: input channel speed: (min=3.784; avg=5687.521; max=19073.486)Mibits/s
rngtest: FIPS tests speed: (min=47.684; avg=52.348; max=52.835)Mibits/s
rngtest: Program run time: 30000987 microseconds
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
After discussing with Amlogic, the Synopsys GMAC version used by
the gx and axg family is the 3.70a. Set this is in DT
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
With the X96 Max board using an external Gigabit Ethernet PHY,
add the same driver strength to the Ethernet pins as the vendor
tree.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
With the default boot settings, the DDC drive strength is too weak,
set the driver-strengh to 4mA to avoid errors on the DDC line.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the network interface of the SEI510 which use the internal PHY.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The u200 is the main mother board for the S905D2. It can provide
both the internal and external network. However, by default the
resistance required for the external RGMII bus are not fitted, so
enable the internal PHY.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the g12a mdio multiplexer which allows to connect to either
an external phy through the SoC pins or the internal 10/100 phy
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the ethernet pinctrl settings for RMII, RGMII and internal phy leds
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Armada 7040-db USB ports deliver 500mA by default while they
could deliver up to 900mA (usually, for USB3 devices).
The board embeds a GPIO controlled regulator on each port which can be
configured to deliver each amount of current.
Add a vin-supply property to the USB3 Vbus nodes for this purpose. The
regulator will be automatically 'enabled', ie. set to limit at 900mA
instead of 500mA.
Suggested-by: Alex Leibovich <alexl@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Allwinner sun6i DMA drivers is used on A64 and H6 boards.
Enable it as a module.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
In set_pte_at(), we read the old pte value so that it can be passed into
checks for racy hw updates. These checks are only performed for
CONFIG_DEBUG_VM, and the value is not used otherwise.
Since we read the pte value with READ_ONCE(), the compiler cannot elide
the redundant read for !CONFIG_DEBUG_VM kernels.
Let's ameliorate matters by moving the read and the checks into a
helper, __check_racy_pte_update(), which only performs the read when the
value will be used. This also allows us to reformat the conditions for
clarity.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Wire up the clone3() call on all arches that don't require hand-rolled
assembly.
Some of the arches look like they need special assembly massaging and it is
probably smarter if the appropriate arch maintainers would do the actual
wiring. Arches that are wired-up are:
- x86{_32,64}
- arm{64}
- xtensa
Signed-off-by: Christian Brauner <christian@brauner.io>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Kees Cook <keescook@chromium.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Adrian Reber <adrian@lisas.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Florian Weimer <fweimer@redhat.com>
Cc: linux-api@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: x86@kernel.org
Until recently, if KBUILD_DEFCONFIG was not set by the arch Makefile,
the default path arch/*/defconfig was used.
The last users of the default are gone by the following commits:
- Commit f3e20ad67b ("s390: move arch/s390/defconfig to
arch/s390/configs/defconfig")
- Commit 986a13769c ("alpha: move arch/alpha/defconfig to
arch/alpha/configs/defconfig")
Let's set arch/*/configs/defconfig as a new default. This saves
KBUILD_DEFCONFIG for some architectures.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds a reset-cells property to the gcc controller on the QCS404.
Without this in place, we get warnings like the following if nodes reference
a gcc reset:
arch/arm64/boot/dts/qcom/qcs404.dtsi:261.38-310.5: Warning (resets_property):
/soc@0/remoteproc@b00000: Missing property '#reset-cells' in node
/soc@0/clock-controller@1800000 or bad phandle (referred from resets[0])
also defined at arch/arm64/boot/dts/qcom/qcs404-evb.dtsi:82.18-84.3
DTC arch/arm64/boot/dts/qcom/qcs404-evb-4000.dtb
arch/arm64/boot/dts/qcom/qcs404.dtsi:261.38-310.5: Warning (resets_property):
/soc@0/remoteproc@b00000: Missing property '#reset-cells' in node
/soc@0/clock-controller@1800000 or bad phandle (referred from resets[0])
also defined at arch/arm64/boot/dts/qcom/qcs404-evb.dtsi:82.18-84.3
Signed-off-by: Andy Gross <agross@kernel.org>
CoreSight DT bindings have been updated, thus the old compatible strings
are obsolete and the drivers will report warning if DTS uses these
obsolete strings.
This patch switches to the new bindings for CoreSight dynamic funnel,
so can dismiss warning during initialisation.
Cc: Andy Gross <agross@kernel.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Another round of SPDX header file fixes for 5.2-rc4
These are all more "GPL-2.0-or-later" or "GPL-2.0-only" tags being
added, based on the text in the files. We are slowly chipping away at
the 700+ different ways people tried to write the license text. All of
these were reviewed on the spdx mailing list by a number of different
people.
We now have over 60% of the kernel files covered with SPDX tags:
$ ./scripts/spdxcheck.py -v 2>&1 | grep Files
Files checked: 64533
Files with SPDX: 40392
Files with errors: 0
I think the majority of the "easy" fixups are now done, it's now the
start of the longer-tail of crazy variants to wade through.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPuGTg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykBvQCg2SG+HmDH+tlwKLT/q7jZcLMPQigAoMpt9Uuy
sxVEiFZo8ZU9v1IoRb1I
=qU++
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Another round of SPDX header file fixes for 5.2-rc4
These are all more "GPL-2.0-or-later" or "GPL-2.0-only" tags being
added, based on the text in the files. We are slowly chipping away at
the 700+ different ways people tried to write the license text. All of
these were reviewed on the spdx mailing list by a number of different
people.
We now have over 60% of the kernel files covered with SPDX tags:
$ ./scripts/spdxcheck.py -v 2>&1 | grep Files
Files checked: 64533
Files with SPDX: 40392
Files with errors: 0
I think the majority of the "easy" fixups are now done, it's now the
start of the longer-tail of crazy variants to wade through"
* tag 'spdx-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (159 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 450
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 449
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 448
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 446
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 445
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 444
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 443
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 442
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 441
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 440
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 438
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 437
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 436
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 435
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 434
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 433
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 432
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 431
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 430
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 429
...
Mostly due to x86 and acpi conversion, several documentation
links are still pointing to the old file. Fix them.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Sven Van Asbroeck <TheSven73@gmail.com>
Reviewed-by: Bhupesh Sharma <bhsharma@redhat.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix boot crash on platforms with SVE2 due to missing register encoding
- Fix architected timer accessors when CONFIG_OPTIMIZE_INLINING=y
- Move cpu_logical_map into smp.h for use by upcoming irqchip drivers
- Trivial typo fix in comment
- Disable some useless, noisy warnings from GCC 9
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAlz6QlIACgkQt6xw3ITB
YzQJRAf/e2PwVOHLwUIbPg//rKKNlJmBMnIUROEiAPjY7atTfjuYd3/65pIq7ZuO
RjMIUT1A2kg+pMOFzmXObLICq3Xl1/7LUUPIQ1iDvEeWIRb7HKQXoJkg9lvUEy89
T4sR1EBkK7uYh0w+/L7k1LESGgl4+VFY/ZY+4NmwsXEK4jfty3by7zE7Vy35MvQ6
XuEbYuMNjfskgBGbZPVqV8qHUlRurfhWWXjdgdAe9E7+fsHPuOrIr4+uXwAyVtRR
1/4tLySNW2GE8o0Ftun82ZasFTTgPc18ozASBYX1FMlQRaXznNREmSHYaIiartJE
VorEdRe25ztdI54fVM2dL0KKmTZi1g==
=ErME
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Another round of mostly-benign fixes, the exception being a boot crash
on SVE2-capable CPUs (although I don't know where you'd find such a
thing, so maybe it's benign too).
We're in the process of resolving some big-endian ptrace breakage, so
I'll probably have some more for you next week.
Summary:
- Fix boot crash on platforms with SVE2 due to missing register
encoding
- Fix architected timer accessors when CONFIG_OPTIMIZE_INLINING=y
- Move cpu_logical_map into smp.h for use by upcoming irqchip drivers
- Trivial typo fix in comment
- Disable some useless, noisy warnings from GCC 9"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Silence gcc warnings about arch ABI drift
ARM64: trivial: s/TIF_SECOMP/TIF_SECCOMP/ comment typo fix
arm64: arch_timer: mark functions as __always_inline
arm64: smp: Moved cpu_logical_map[] to smp.h
arm64: cpufeature: Fix missing ZFR0 in __read_sysreg_by_encoding()
__do_page_fault() is over complicated with multiple goto statements. This
cleans up the code flow and while there drops local variable vm_fault_t.
Reviewed-by: Mark Rutland <Mark.rutland@arm.com>
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds an is_write_abort() wrapper and documents the detection
of the abort type on cache maintenance operations.
Cc: Will Deacon <will.deacon@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
[catalin.marinas@arm.com: only keep the is_write_abort() wrapper]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The config value used in the if was changed in
b433dce056, but the comment on the
corresponding end was not changed.
Signed-off-by: Odin Ugedal <odin@ugedal.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Because of register and bits difference for setting PHY modes, PTP reference
clock, and FPGA signalling, the Stratix10 SoC needs to use the
"altr,socfpga-stmmac-a10-s10" binding to set the correct modes.
On Stratix10, each EMAC has its own register for PHY modes, and they all have
the same offset, thus we can use the 2nd parameter to specify the offsets
for the FPGA signal bits.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
The HiHope RZ/G2M sub board sits below the HiHope RZ/G2M main board.
This patch also adds ethernet support along with a dtsi common to
both HiHope RZ/G2M and RZ/G2N sub boards.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds pincontrol support to scif2/scif clock.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Basic support for the HiHope RZ/G2M main board:
- Memory,
- Main crystal,
- Serial console
This patch also includes a dtsi common to both HiHope RZ/G2M
and RZ/G2N main boards.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since GCC 9, the compiler warns about evolution of the
platform-specific ABI, in particular relating for the marshaling of
certain structures involving bitfields.
The kernel is a standalone binary, and of course nobody would be
so stupid as to expose structs containing bitfields as function
arguments in ABI. (Passing a pointer to such a struct, however
inadvisable, should be unaffected by this change. perf and various
drivers rely on that.)
So these warnings do more harm than good: turn them off.
We may miss warnings about future ABI drift, but that's too bad.
Future ABI breaks of this class will have to be debugged and fixed
the traditional way unless the compiler evolves finer-grained
diagnostics.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Fix a s/TIF_SECOMP/TIF_SECCOMP/ comment typo
Cc: Jiri Kosina <trivial@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The RZ/G2M (a.k.a. r8a774a1) comes with two clusters of
processors, similarly to the r8a7796.
The first cluster is made of A57s, the second cluster is
made of A53s.
The operating points for the cluster with the A57s are:
Frequency | Voltage
-----------|---------
500 MHz | 0.82V
1.0 GHz | 0.82V
1.5 GHz | 0.82V
The operating points for the cluster with the A53s are:
Frequency | Voltage
-----------|---------
800 MHz | 0.82V
1.0 GHz | 0.82V
1.2 GHz | 0.82V
This patch adds the definitions for the operating points
to the SoC specific DT.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the dynamic power coefficient of A53 CPUs.
Based on work by Gaku Inami <gaku.inami.xw@bp.renesas.com> and others.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Setup a thermal zone driven by SoC temperature sensor.
Create passive trip points and bind them to CPUFreq cooling
device that supports power extension.
In R-Car Gen3, IPA is supported for only one channel
Reason:
Currently, IPA controls base on only CPU temperature.
And only one thermal channel is assembled closest
CPU cores is selected as target of IPA.
If other channels are used, IPA controlling is not properly.
A single cooling device is described for all A53 CPUs as this
reflects that physically there is only one cooling device present.
This patch improves on an earlier version by:
* Omitting cooling-max-level and cooling-min-level properties which
are no longer present in mainline as of v4.17
* Removing an unused trip-point0 node sub-property from the trips
property.
* Defers adding dynamic-power-coefficient properties to a separate patch as
these are properties of the CPU.
The long signed-off by chain below reflects many revisions, mainly
internal, that this patch has been through.
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the dynamic power coefficient of A57 and A53 CPUs.
Based on work by Gaku Inami <gaku.inami.xw@bp.renesas.com> and others.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Setup a thermal zone driven by SoC temperature sensor.
Create passive trip points and bind them to CPUFreq cooling
device that supports power extension.
In R-Car Gen3, IPA is supported for only one channel
(on H3/M3/M3N SoCs, it is channel THS3). Reason:
Currently, IPA controls base on only CPU temperature.
And only one thermal channel is assembled closest
CPU cores is selected as target of IPA.
If other channels are used, IPA controlling is not properly.
The A57 cooling device supports 5 cooling states which can be categorised
as follows:
0 & 1) boost (clocking up)
2) default
3 & 4) cooling (clocking down)
Currently the thermal framework assumes that the default is the minimum,
or in other words there is no provision for handling boost states.
So this patch only describes the upper 3 states, default and cooling.
A single cooling device is described for all A57 CPUs and a separate
cooling device is described for all A53 CPUs. This reflects that physically
there is only one cooling device present for each type of CPU.
This patch improves on an earlier version by:
* Omitting cooling-max-level and cooling-min-level properties which
are no longer present in mainline as of v4.17
* Removing an unused trip-point0 node sub-property from the trips
property.
* Using cooling-device indexes such that maximum refers to maximum cooling
rather than the inverse.
* Defers adding dynamic-power-coefficient properties to a separate patch as
these are properties of the CPU.
The long signed-off by chain below reflects many revisions, mainly
internal, that this patch has been through.
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
Signed-off-by: An Huynh <an.huynh.uj@rvc.renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the dynamic power coefficient of A57 and A53 CPUs.
Based on work by Gaku Inami <gaku.inami.xw@bp.renesas.com> and others.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Setup a thermal zone driven by SoC temperature sensor.
Create passive trip points and bind them to CPUFreq cooling
device that supports power extension.
In R-Car Gen3, IPA is supported for only one channel
(on H3/M3/M3N SoCs, it is channel THS3). Reason:
Currently, IPA controls base on only CPU temperature.
And only one thermal channel is assembled closest
CPU cores is selected as target of IPA.
If other channels are used, IPA controlling is not properly.
The A57 cooling device supports 5 cooling states which can be categorised
as follows:
0 & 1) boost (clocking up)
2) default
3 & 4) cooling (clocking down)
Currently the thermal framework assumes that the default is the minimum,
or in other words there is no provision for handling boost states.
So this patch only describes the upper 3 states, default and cooling.
A single cooling device is described for all A57 CPUs and a separate
cooling device is described for all A53 CPUs. This reflects that physically
there is only one cooling device present for each type of CPU.
This patch improves on an earlier version by:
* Omitting cooling-max-level and cooling-min-level properties which
are no longer present in mainline as of v4.17
* Removing an unused trip-point0 node sub-property from the trips
property.
* Using cooling-device indexes such that maximum refers to maximum cooling
rather than the inverse.
* Defers adding dynamic-power-coefficient properties to a separate patch as
these are properties of the CPU.
The long signed-off by chain below reflects many revisions, mainly
internal, that this patch has been through.
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
Signed-off-by: Hien Dang <hien.dang.eb@rvc.renesas.com>
Signed-off-by: An Huynh <an.huynh.uj@rvc.renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the dynamic power coefficient of A57 and A53 CPUs.
Based on work by Gaku Inami <gaku.inami.xw@bp.renesas.com> and others.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Setup a thermal zone driven by SoC temperature sensor.
Create passive trip points and bind them to CPUFreq cooling
device that supports power extension.
In R-Car Gen3, IPA is supported for only one channel
(on H3/M3/M3N SoCs, it is channel THS3). Reason:
Currently, IPA controls base on only CPU temperature.
And only one thermal channel is assembled closest
CPU cores is selected as target of IPA.
If other channels are used, IPA controlling is not properly.
The A5 cooling device supports 5 cooling states which can be categorised as
follows:
0 & 1) boost (clocking up)
2) default
3 & 4) cooling (clocking down)
Currently the thermal framework assumes that the default is the minimum,
or in other words there is no provision for handling boost states.
So this patch only describes the upper 3 states, default and cooling.
A single cooling device is described for all A57 CPUs and a separate
cooling device is described for all A53 CPUs. This reflects that physically
there is only one cooling device present for each type of CPU.
This patch improves on an earlier version by:
* Omitting cooling-max-level and cooling-min-level properties which
are no longer present in mainline as of v4.17
* Removing an unused trip-point0 node sub-property from the trips
property.
* Using cooling-device indexes such that maximum refers to maximum cooling
rather than the inverse.
* Defers adding dynamic-power-coefficient properties to a separate patch as
these are properties of the CPU.
The long signed-off by chain below reflects many revisions, mainly
internal, that this patch has been through.
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
Signed-off-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Hien Dang <hien.dang.eb@rvc.renesas.com>
Signed-off-by: An Huynh <an.huynh.uj@rvc.renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since the commit 233da2c9ec ("dt-bindings: phy: rcar-gen3-phy-usb2:
Revise #phy-cells property") revised the #phy-cells, this patch follows
the updated document for R-Car Gen3 and RZ/A2 SoCs.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
It is incorrect to specify the no-ether-link property for the AVB device on
the Ebisu board. This is because the property should only be used when a
board does not provide a proper AVB_LINK signal. However, the Ebisu board
does provide this signal.
As per 87c059e9c3 ("arm64: dts: renesas: salvator-x: Remove renesas,
no-ether-link property") this fixes a bug:
Steps to reproduce:
- start AVB TX stream (Using aplay via MSE),
- disconnect+reconnect the eth cable,
- after a reconnection the eth connection goes iteratively up/down
without user interaction,
- this may heal after some seconds or even stay for minutes.
As the documentation specifies, the "renesas,no-ether-link" option
should be used when a board does not provide a proper AVB_LINK signal.
There is no need for this option enabled on RCAR H3/M3 Salvator-X/XS
and ULCB starter kits since the AVB_LINK is correctly handled by HW.
Choosing to keep or remove the "renesas,no-ether-link" option will have
impact on the code flow in the following ways:
- keeping this option enabled may lead to unexpected behavior since the
RX & TX are enabled/disabled directly from adjust_link function
without any HW interrogation,
- removing this option, the RX & TX will only be enabled/disabled after
HW interrogation. The HW check is made through the LMON pin in PSR
register which specifies AVB_LINK signal value (0 - at low level;
1 - at high level).
In conclusion, the present change is also a safety improvement because
it removes the "renesas,no-ether-link" option leading to a proper way
of detecting the link state based on HW interrogation and not on
software heuristic.
Fixes: 8441ef643d ("arm64: dts: renesas: r8a77990: ebisu: Enable EthernetAVB")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[simon: updated changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Apparently this DTS crossed over with commit 31af04cd60 ("arm64: dts:
Remove inconsistent use of 'arm,armv8' compatible string") and missed
out on the cleanup, so put it right.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Convert bootargs from ip=dhcp to ip=on
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The sha256-ce finup implementation for ARM64 produces wrong digest
for empty input (len=0). Expected: the actual digest, result: initial
value of SHA internal state. The error is in sha256_ce_finup:
for empty data `finalize` will be 1, so the code is relying on
sha2_ce_transform to make the final round. However, in
sha256_base_do_update, the block function will not be called when
len == 0.
Fix it by setting finalize to 0 if data is empty.
Fixes: 03802f6a80 ("crypto: arm64/sha2-ce - move SHA-224/256 ARMv8 implementation to base layer")
Cc: stable@vger.kernel.org
Signed-off-by: Elena Petrova <lenaptr@google.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The sha1-ce finup implementation for ARM64 produces wrong digest
for empty input (len=0). Expected: da39a3ee..., result: 67452301...
(initial value of SHA internal state). The error is in sha1_ce_finup:
for empty data `finalize` will be 1, so the code is relying on
sha1_ce_transform to make the final round. However, in
sha1_base_do_update, the block function will not be called when
len == 0.
Fix it by setting finalize to 0 if data is empty.
Fixes: 07eb54d306 ("crypto: arm64/sha1-ce - move SHA-1 ARMv8 implementation to base layer")
Cc: stable@vger.kernel.org
Signed-off-by: Elena Petrova <lenaptr@google.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
GIC is inside of SoC from architecture perspective, it should
be located inside of soc node in DT.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add PTRACE_SYSEMU and PTRACE_SYSEMU_SINGLESTEP support on arm64.
We don't need any special handling for PTRACE_SYSEMU_SINGLESTEP.
It's quite difficult to generalize handling PTRACE_SYSEMU cross
architectures and avoid calls to tracehook_report_syscall_entry twice.
Different architecture have different mechanism to indicate NO_SYSCALL
and trying to generalise adds more code for no gain.
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
x86 and um use 31 and 32 for PTRACE_SYSEMU and PTRACE_SYSEMU_SINGLESTEP
while powerpc uses different value maybe for legacy reasons.
Though handling of PTRACE_SYSEMU can be made architecture independent,
it's hard to make these definations generic. To add to this existing
mess few architectures like arm, c6x and sh use 31 for PTRACE_GETFDPIC
(get the ELF fdpic loadmap address). It's not possible to move the
definations to generic headers.
So we unfortunately have to duplicate the same defination to ARM64 if
we need to support PTRACE_SYSEMU and PTRACE_SYSEMU_SINGLESTEP.
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 315 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.503150771@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 101 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190113.822954939@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
publishhed by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 48 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.292339952@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed as is without any warranty of any kind whether express
or implied without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141332.617181045@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_FUNCTION_GRAPH_TRACER is enabled function
arch_counter_get_cntvct() is marked as notrace. However, function
__arch_counter_get_cntvct is marked as inline. If
CONFIG_OPTIMIZE_INLINING is set that will make the two functions
tracable which they shouldn't.
Rework so that functions __arch_counter_get_* are marked with
__always_inline so they will be inlined even if CONFIG_OPTIMIZE_INLINING
is turned on.
Fixes: 0ea415390c ("clocksource/arm_arch_timer: Use arch_timer_read_counter to access stable counters")
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
asm/smp.h is included by linux/smp.h and some drivers, in particular
irqchip drivers can access cpu_logical_map[] in order to perform SMP
affinity tasks. Make arm64 consistent with other architectures here.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In commit 06a916feca ("arm64: Expose SVE2 features for
userspace"), new hwcaps are added that are detected via fields in
the SVE-specific ID register ID_AA64ZFR0_EL1.
In order to check compatibility of secondary cpus with the hwcaps
established at boot, the cpufeatures code uses
__read_sysreg_by_encoding() to read this ID register based on the
sys_reg field of the arm64_elf_hwcaps[] table.
This leads to a kernel splat if an hwcap uses an ID register that
__read_sysreg_by_encoding() doesn't explicitly handle, as now
happens when exercising cpu hotplug on an SVE2-capable platform.
So fix it by adding the required case in there.
Fixes: 06a916feca ("arm64: Expose SVE2 features for userspace")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
usbphy nodes do not have any register properties and thus
shouldn't be placed inside the bus.
Move usbphy nodes from soc node to root node in order to fix
the following build warnings with W=1:
arch/arm64/boot/dts/freescale/imx8mm.dtsi:681.27-687.6: Warning (simple_bus_reg): /soc/bus@32c00000/usbphynop1: missing or empty reg/ranges property
arch/arm64/boot/dts/freescale/imx8mm.dtsi:710.27-716.6: Warning (simple_bus_reg): /soc/bus@32c00000/usbphynop2: missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass the 'ranges' property for each one of the AIPS bus in order
to fix the following build warnings:
arch/arm64/boot/dts/freescale/imx8mm.dtsi:209.23-388.5: Warning (unit_address_vs_reg): /soc/bus@30000000: node has a unit name, but
no reg property
arch/arm64/boot/dts/freescale/imx8mm.dtsi:390.23-439.5: Warning (unit_address_vs_reg): /soc/bus@30400000: node has a unit name, but
no reg property
arch/arm64/boot/dts/freescale/imx8mm.dtsi:441.23-658.5: Warning (unit_address_vs_reg): /soc/bus@30800000: node has a unit name, but
no reg property
arch/arm64/boot/dts/freescale/imx8mm.dtsi:660.23-724.5: Warning (unit_address_vs_reg): /soc/bus@32c00000: node has a unit name, but
no reg property
This also aligns with imx8mq.dtsi.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The 'soc' name needs a unit name to match its 'ranges' property.
Pass the unit name in order to fix the following dtc build warning
with W=1:
arch/arm64/boot/dts/freescale/imx8mm.dtsi:203.6-754.4: Warning (unit_address_vs_reg): /soc: node has a reg or ranges property, but no unit name
This also aligns with imx8mq.dtsi.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a node for the snvs power key, "disabled" by default.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Two of the Tegra I2C controllers share pads with the DPAUX controllers.
In order for the I2C controllers to use these pads, they have to be set
into I2C mode. Use the I2C and off pin control states defined in the DT
nodes for DPAUX as "default" and "idle" states, respectively. This
ensures that the I2C controller driver can properly configure the pins
when it needs to perform I2C transactions.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra186 has two CPU clusters with its own cache hierarchy. This patch
adds them with the cache information of each of the CPUs.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The GPIO expanders on Jetson TX2 are powered by the VDD_1V8 and
VDD_3V3_SYS supplies, respectively. Model this in device tree so that
the correct supplies are referenced.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
ls1028a platform uses sp805 watchdog, and use 1/16 platform clock as
timer clock, this patch fix device tree node.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX system controller watchdog has pretimeout function which
depends on i.MX SCU driver, so it should be a subnode of SCU.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The task_struct argument is not getting used in __do_page_fault(). Hence
just drop it and use current or cuurent->mm instead where ever required.
This does not change any functionality.
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
There is an inconsistency between down_read_trylock() success and failure
paths while dealing with kernel access for non exception table areas where
it calls __do_kernel_fault(). In case of failure it just bails out without
holding mmap_sem but when it succeeds it does so while holding mmap_sem.
Fix this inconsistency by just dropping mmap_sem in success path as well.
__do_kernel_fault() calls die_kernel_fault() which then calls show_pte().
show_pte() in this path might become bit more unreliable without holding
mmap_sem. But there are already instances [1] in do_page_fault() where
die_kernel_fault() gets called without holding mmap_sem. show_pte() can
be made more robust independently but in a later patch.
[1] Conditional block for (is_ttbr0_addr && is_el1_permission_fault)
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We don't currently set the FAULT_FLAG_INSTRUCTION mm flag for EL0
instruction aborts. This has no functional impact, as we don't override
arch_vma_access_permitted(), and the default implementation always returns
true. However, it would be helpful to provide the flag so that it can be
consumed by tracepoints such as dax_pmd_fault.
This patch sets the FAULT_FLAG_INSTRUCTION flag for EL0 instruction aborts.
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
There are no callers for the functions which will pass unaligned physical
addresses. Hence just change these BUG_ON() checks into VM_BUG_ON() which
gets compiled out unless CONFIG_VM_DEBUG is enabled.
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
cpu_enable_ssbs() is called via stop_machine() as part of the cpu_enable
callback. A spin lock is used to ensure the hook is registered before
the rest of the callback is executed.
On -RT spin_lock() may sleep. However, all the callees in stop_machine()
are expected to not sleep. Therefore a raw_spin_lock() is required here.
Given this is already done under stop_machine() and the work done under
the lock is quite small, the latency should not increase too much.
Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Rock Pi 4 has a on board AP6256 WiFi/BT Module. enable wifi and bluetooth
support on Rock Pi 4 board.
Signed-off-by: Akash Gajjar <akash@openedev.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
isp iommu requires wrapper variants of the clocks.
noc variants are always on and using the wrapper variants will activate
{A,H}CLK_ISP{0,1} due to the hierarchy.
Tested using the pending isp patch set (which is not upstream
yet). Without this patch, streaming from the isp stalls.
Also add the respective power domain and remove the "disabled" status.
Refer:
RK3399 TRM v1.4 Fig. 2-4 RK3399 Clock Architecture Diagram
RK3399 TRM v1.4 Fig. 8-1 RK3399 Power Domain Partition
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This change makes CONFIG_ZONE_DMA32 defuly y and allows users
to overwrite it only when CONFIG_EXPERT=y.
For the SoCs that do not need CONFIG_ZONE_DMA32, this is the
first step to manage all available memory by a single
zone(normal zone) to reduce the overhead of multiple zones.
The change also fixes a build error when CONFIG_NUMA=y and
CONFIG_ZONE_DMA32=n.
arch/arm64/mm/init.c:195:17: error: use of undeclared identifier 'ZONE_DMA32'
max_zone_pfns[ZONE_DMA32] = PFN_DOWN(max_zone_dma_phys());
Change since v1:
1. only expose CONFIG_ZONE_DMA32 when CONFIG_EXPERT=y
2. remove redundant IS_ENABLED(CONFIG_ZONE_DMA32)
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Miles Chen <miles.chen@mediatek.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Even though they have got the same value, PMD_TYPE_SECT and PUD_TYPE_SECT
get used for kernel huge mappings. But before that first the table bit gets
cleared using leaf level PTE_TABLE_BIT. Though functionally they are same,
we should use page table level specific macros to be consistent as per the
MMU specifications. Create page table level specific wrappers for kernel
huge mapping entries and just drop mk_sect_prot() which does not have any
other user.
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
cache_line_size is derived from CTR_EL0.CWG field and is called mostly
for I/O device drivers. For some platforms like the HiSilicon Kunpeng920
server SoC, cache line sizes are different between L1/2 cache and L3
cache while L1 cache line size is 64-byte and L3 is 128-byte, but
CTR_EL0.CWG is misreporting using L1 cache line size.
We shall correct the right value which is important for I/O performance.
Let's update the cache line size if it is detected from DT or PPTT
information.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Jeremy Linton <jeremy.linton@arm.com>
Cc: Zhenfa Qiu <qiuzhenfa@hisilicon.com>
Reported-by: Zhenfa Qiu <qiuzhenfa@hisilicon.com>
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When the kernel is compiled with CONFIG_KERNEL_MODE_NEON, some part of
the kernel may be able to use FPSIMD/SVE. This is for instance the case
for crypto code.
Any use of FPSIMD/SVE in the kernel are clearly marked by using the
function kernel_neon_{begin, end}. Furthermore, this can only be used
when may_use_simd() returns true.
The current implementation of may_use_simd() allows softirq to use
FPSIMD/SVE unless it is currently in use (i.e kernel_neon_busy is true).
When in use, softirqs usually fall back to a software method.
At the moment, as a softirq may use FPSIMD/SVE, softirqs are disabled
when touching the FPSIMD/SVE context. This has the drawback to disable
all softirqs even if they are not using FPSIMD/SVE.
Since a softirq is supposed to check may_use_simd() anyway before
attempting to use FPSIMD/SVE, there is limited reason to keep softirq
disabled when touching the FPSIMD/SVE context. Instead, we can simply
disable preemption and mark the FPSIMD/SVE context as in use by setting
CPU's fpsimd_context_busy flag.
Two new helpers {get, put}_cpu_fpsimd_context are introduced to mark
the area using FPSIMD/SVE context and they are used to replace
local_bh_{disable, enable}. The functions kernel_neon_{begin, end} are
also re-implemented to use the new helpers.
Additionally, double-underscored versions of the helpers are provided to
called when preemption is already disabled. These are only relevant on
paths where irqs are disabled anyway, so they are not needed for
correctness in the current code. Let's use them anyway though: this
marks critical sections clearly and will help to avoid mistakes during
future maintenance.
The change has been benchmarked on Linux 5.1-rc4 with defconfig.
On Juno2:
* hackbench 100 process 1000 (10 times)
* .7% quicker
On ThunderX 2:
* hackbench 1000 process 1000 (20 times)
* 3.4% quicker
Reviewed-by: Dave Martin <dave.martin@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The only external user of fpsimd_save() and fpsimd_flush_cpu_state() is
the KVM FPSIMD code.
A following patch will introduce a mechanism to acquire owernship of the
FPSIMD/SVE context for performing context management operations. Rather
than having to export the new helpers to get/put the context, we can just
introduce a new function to combine fpsimd_save() and
fpsimd_flush_cpu_state().
This has also the advantage to remove any external call of fpsimd_save()
and fpsimd_flush_cpu_state(), so they can be turned static.
Lastly, the new function can also be used in the PM notifier.
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The function sve_flush_cpu_state() has been removed in commit 21cdd7fd76
("KVM: arm64: Remove eager host SVE state saving").
So remove the associated prototype in asm/fpsimd.h.
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Enlarge the SGMII register range and using 2.5G force mode on default.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTE_VALID signifies that the last level page table entry is valid and it is
MMU recognized while walking the page table. This is not a software defined
PTE bit and should not be listed like one. Just move it to appropriate
header file.
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Steve Capper <steve.capper@arm.com>
Cc: Suzuki Poulose <suzuki.poulose@arm.com>
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Replace all open encoded contiguous huge page size computations with
available macro encodings CONT_PTE_SIZE and CONT_PMD_SIZE. There are other
instances where these macros are used in the file and this change makes it
consistently use the same mnemonic.
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Steve Capper <steve.capper@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The manufacturer of this board, ships it with various SPI NOR chips and
increments U-Boot bootloader version along the time. There is no way to
tell which is placed on the board since no revision bump takes place.
This creates two issues.
The first, cosmetic. Since the NOR chip may differ, there's message on
boot stating that kernel expected w25q32dw and found different one. To
correct this, remove optional device-specific compatible string. Being
here lets replace bogus "spi-flash" compatible string with proper one.
The second is linked to partitions layout, it changed after commit:
81e7251252 ("arm64: mvebu: config: move env to the end of the 4MB boot
device") in Marvells downstream U-Boot fork [1], shifting environment
location to the end of boot device. Since the new boards will have U-Boot
with this change, it'll lead to improper results writing or reading from
these partitions. We can't tell if users will update bootloader to recent
version provided on manufacturer website, so lets drop partitons layout.
1. https://github.com/MarvellEmbeddedProcessors/u-boot-marvell.git
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
While AP I2C bus was available to users in early revisions of the SoC,
this is not the case anymore since eMMC was connected to the AP. Most
users do not have access to this I2C bus so do not enable it in the
board device tree.
As there are three I2C buses enabled on this board, add an alias to be
sure the two other buses keep their initial numbering.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
[<miquel.raynal@bootlin.com>: Reword commit message, add alias]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Avoid critical temperatures in the AP806 by adding the relevant trip
points/cooling-maps using CPUfreq as cooling device.
So far, when the temperature reaches 100°C in the thermal IP of the
AP806 (close enough from the 2/4 cores) an overheat interrupt is
raised. The thermal core then shutdowns the system to avoid damaging
the hardware.
Adding CPUfreq as a cooling device could help avoiding such very
critical situation. For that, we enable thermal throttling by
defining, for each CPU, two trip points with the corresponding cooling
'intensity'. CPU0 and CPU1 are in the same cluster and are driven by
the same clock. Same applies for CPU2 and CPU3, if available. So
changing the frequency of one will also change the frequency of the
other one, hence the use of two cooling devices per core.
The heat map is as follow:
- Below 85°C: the cluster runs at the highest frequency
(e.g: 1200MHz).
- Between 85°C and 95°C: there are two trip points at half
(e.g: 600MHz) and a third (e.g: 400MHz) of the highest frequency.
- Above 95°C the cluster runs at a quarter of the highest frequency
(e.g: 300MHz).
- At 100°C the platform is shutdown.
Suggested-by: Omri Itach <omrii@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
When adding thermal nodes, the CPUs have been named from 1 to 4 while
usually everywhere else they are referred as 0-3. Let's change this to
be consistent with later changes when we will use CPUfreq and CPU
phandles as cooling devices to avoid inconsistencies in the nodes
numbering.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The Clearfog GT-8K board is capable of supplying power up to 2W to SFP
modules. Make that explicit in the device-tree. Without this property
current kernel does not allow SFP modules that require more than 1W.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Running a graphics adapter on the MACCHIATObin fails due to an
insufficiently sized memory window.
Enlarge the memory window for the PCIe slot to 512 MiB.
With the patch I am able to use a GT710 graphics adapter with 1 GB onboard
memory.
These are the mapped memory areas that the graphics adapter is actually
using:
Region 0: Memory at cc000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at c0000000 (64-bit, prefetchable) [size=128M]
Region 3: Memory at c8000000 (64-bit, prefetchable) [size=32M]
Region 5: I/O ports at 1000 [size=128]
Expansion ROM at ca000000 [disabled] [size=512K]
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The phylink conflict was between a bug fix by Russell King
to make sure we have a consistent PHY interface mode, and
a change in net-next to pull some code in phylink_resolve()
into the helper functions phylink_mac_link_{up,down}()
On the dp83867 side it's mostly overlapping changes, with
the 'net' side removing a condition that was supposed to
trigger for RGMII but because of how it was coded never
actually could trigger.
Signed-off-by: David S. Miller <davem@davemloft.net>
ARCH_BRCMSTB needs to use the BCM2835 pin controller for chips like
BCM7211 which adopted that pin controller for GPIO.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Allow the use of reset controllers on ARCH_BRCMSTB such as the recently
introduced RESET_BRCMSTB driver.
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Here is another set of reviewed patches that adds SPDX tags to different
kernel files, based on a set of rules that are being used to parse the
comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review and
analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPCHLg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykxyACgql6ktH+Tv8Ho1747kKPiFca1Jq0AoK5HORXI
yB0DSTXYNjMtH41ypnsZ
=x2f8
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review
and analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (82 commits)
treewide: Add SPDX license identifier - Kbuild
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 225
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 224
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 223
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 222
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 221
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 220
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 218
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 217
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 216
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 215
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 214
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 213
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 211
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 210
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 209
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 207
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 206
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 203
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 201
...
i.MX8MM has 5 SAI instances with the following base
addresses according to RM.
SAI1 base address: 3001_0000h
SAI2 base address: 3002_0000h
SAI3 base address: 3003_0000h
SAI5 base address: 3005_0000h
SAI6 base address: 3006_0000h
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MQ has clock gate for SNVS module, add clock info to SNVS
RTC node for clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- Fix implementation of our set_personality() system call, which wasn't
being wrapped properly
- Fix system call function types to keep CFI happy
- Fix siginfo layout when delivering SIGKILL after a kernel fault
- Really fix module relocation range checking
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAlzvv3EACgkQt6xw3ITB
YzQviwf9Gw3VrBZpS9nwz0MQCf9W7+Vpy8XBsY7HJyUNQ4+8ZNR5HoZ3BcJX2HWk
WKwSw721MllzLfJaRMqNV2+C7lm+EypcZApKFpPo7Vs9g78WcUdNZ4YM4XfAX45T
cVPxeSGOj2aswyOn2Xa3UjKZj8deP8nAC/JgJY7t9L6qKObwUldmxBPRnZdclclw
S8sQSMvLc9Q43jmEysPLixExZ6jzmq1i8xxPcyqFUz8DHYPf1irLxtpS7DYA+nk5
nwQ/lnz6Tu8TBXcvgvXayKL8aa8SIsl0cOii2FWsZMkFXz3OZ08hdujvMYsPSSHO
q3rMub7F/0znm00sBGXgTGRjy++v+A==
=pyp4
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"The fixes are still trickling in for arm64, but the only really
significant one here is actually fixing a regression in the botched
module relocation range checking merged for -rc2.
Hopefully we've nailed it this time.
- Fix implementation of our set_personality() system call, which
wasn't being wrapped properly
- Fix system call function types to keep CFI happy
- Fix siginfo layout when delivering SIGKILL after a kernel fault
- Really fix module relocation range checking"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: use the correct function type for __arm64_sys_ni_syscall
arm64: use the correct function type in SYSCALL_DEFINE0
arm64: fix syscall_fn_t type
signal/arm64: Use force_sig not force_sig_fault for SIGKILL
arm64/module: revert to unsigned interpretation of ABS16/32 relocations
arm64: Fix the arm64_personality() syscall wrapper redirection
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
license terms gnu general public license gpl version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 161 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170027.447718015@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the rpmpd node on the msm8998 and define the available levels.
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
[bjorn: dropped use of level defines, to allow merging in parallel]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Add the rpmpd node on the qcs404 and define the available levels.
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[sibis: fixup available levels]
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
[bjorn: dropped use of level defines, to allow merging in parallel]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Although we don't describe lpass and wcss with all the details needed to
control them in a Trustzone-less environment, move them under soc in
order to tidy up the structure and prepare for describing them fully.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Add all the properties needed to describe the CDSP for both the
Trustzone and non-Trustzone based remoteproc case, allowing any child
devices to be described once by just overriding the compatible to match
the firmware available on the board.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
The bus halt registers in TCSR are referenced as a syscon device, add
these so that we can reference them from the remoteproc nodes.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
With the Trustzone based CDSP remoteproc driver these clocks are
controlled elsewhere and as they are not enabled by anything in Linux
the clock framework will turn them off during lateinit.
This results in issues either to later start the CDSP, using the
Trustzone interface, or if the CDSP is already running it will crash.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Add device bindings for cpuidle states for cpu devices.
Cc: <mkshah@codeaurora.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org>
[amit: rename the idle-states to more generic names and fixups]
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
msm8996 features 4 cpus - 2 in each cluster. However, all cpus implement
the same microarchitecture and the two clusters only differ in the
maximum frequency attainable by the CPUs.
Add capacity-dmips-mhz property to allow the topology code to determine
the actual capacity by taking into account the highest frequency for
each CPU.
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Add device bindings for cpuidle states for cpu devices.
msm8996 features 4 cpus - 2 in each cluster. However, all cpus implement
the same microarchitecture and the two clusters only differ in the
maximum frequency attainable by the CPUs.
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Instead of using Qualcomm-specific terminology, use generic node names
for the idle states that are easier to understand. Move the description
into the "idle-state-name" property.
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
The idle-states binding documentation[1] mentions that the
'entry-method' property is required on 64-bit platforms and must be set
to "psci".
[1] Documentation/devicetree/bindings/arm/idle-states.txt (see
idle-states node)
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Add a node describing the Turing Clock Controller of the QCS404. Given
the default access restriction the node is left disabled.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Add device bindings for cpuidle states for cpu devices.
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
[amit: rename the idle-states to more generic names and fixups]
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Some Adreno GPU targets require a special zap shader to bring the GPU
out of secure mode. Define a region to allocate and store the zap
shader.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
[bjorn: Rebase ontop of recent reserved-memory patch]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Add the nodes to describe the Adreno GPU and GMU devices for sdm845.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
[bjorn: Added required gx power-domain]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
The MTP is a "mobile reference device", as such the default operation is
to use fastboot to boot/flash software onto it and the common case is
thereby that we boot with a USB cable connected downstream from a PC or
a hub. And without support for the PMI8998 charger block VBUS will not
be driven by the device.
Switch to peripheral until we can enable OTG.
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Increase s3 max voltage in accordance to QCS404 CPR Fusing Guide Rev 6.0
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
The current l3 min voltage level is not supported by
the regulator (the voltage is not a multiple of the regulator step size),
so a driver requesting this exact voltage would fail, see discussion in:
https://patchwork.kernel.org/comment/22461199/
It was agreed upon to set a min voltage level that is a multiple of the
regulator step size.
There was actually a patch sent that did this:
https://patchwork.kernel.org/patch/10819313/
However, the commit 331ab98f8c ("arm64: dts: qcom: qcs404:
Fix voltages l3") that was applied is not identical to that patch.
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
The adc outputs shouldn't contain information about their configuration
e.g. 100K pull-up, but just reflect the name of the signal in the
schematics.
Making them labels also allows us to overwrite their configuration in
board-specific DTs.
Sort them by order as used in adc5_chans_rev2, while we're at it.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Set the qcom,ratiometric property to make the VADC use the VDD reference
(1.875V) and GND for channel calibration of the temperature channels
instead of 1.25V. Allow a 200us delay between the AMUX configuration and
ADC starting conversion using qcom,hw-settle-time as described in
documentation.
Fixes: 041b9a7b9f ("arm64: dts: pms405: Export PMIC temperature to thermal framework")
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
SDM845 implements ARM's Dynamiq architecture that allows the big and
LITTLE cores to exist in a single cluster sharing the L3 cache.
Fix the cpu-map to put all cpus into a single cluster.
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Add the reset controller for the UFS controller, and wire it up
so that the UFS PHY can initialize itself without relying on
implicit sequencing between the two drivers.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
As synchronous exceptions really only make sense against the current
task (otherwise how are you synchronous) remove the task parameter
from from force_sig_fault to make it explicit that is what is going
on.
The two known exceptions that deliver a synchronous exception to a
stopped ptraced task have already been changed to
force_sig_fault_to_task.
The callers have been changed with the following emacs regular expression
(with obvious variations on the architectures that take more arguments)
to avoid typos:
force_sig_fault[(]\([^,]+\)[,]\([^,]+\)[,]\([^,]+\)[,]\W+current[)]
->
force_sig_fault(\1,\2,\3)
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Calling sys_ni_syscall through a syscall_fn_t pointer trips indirect
call Control-Flow Integrity checking due to a function type
mismatch. Use SYSCALL_DEFINE0 for __arm64_sys_ni_syscall instead and
remove the now unnecessary casts.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Although a syscall defined using SYSCALL_DEFINE0 doesn't accept
parameters, use the correct function type to avoid indirect call
type mismatches with Control-Flow Integrity checking.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Syscall wrappers in <asm/syscall_wrapper.h> use const struct pt_regs *
as the argument type. Use const in syscall_fn_t as well to fix indirect
call type mismatches with Control-Flow Integrity checking.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
I don't think this is userspace visible but SIGKILL does not have
any si_codes that use the fault member of the siginfo union. Correct
this the simple way and call force_sig instead of force_sig_fault when
the signal is SIGKILL.
The two know places where synchronous SIGKILL are generated are
do_bad_area and fpsimd_save. The call paths to force_sig_fault are:
do_bad_area
arm64_force_sig_fault
force_sig_fault
force_signal_inject
arm64_notify_die
arm64_force_sig_fault
force_sig_fault
Which means correcting this in arm64_force_sig_fault is enough
to ensure the arm64 code is not misusing the generic code, which
could lead to maintenance problems later.
Cc: stable@vger.kernel.org
Cc: Dave Martin <Dave.Martin@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Fixes: af40ff687b ("arm64: signal: Ensure si_code is valid for all fault signals")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Even though it translates to the same thing down to the binary level, we
should have an array of 2 number cells to describe each voltage state,
which in turns create a validation warning.
Let's fix this.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This patch enables BT support for the CAT874 board.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables WLAN support for the CAT874 board.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commit 1cf24a2cc3
("arm64/module: deal with ambiguity in PRELxx relocation ranges")
updated the overflow checking logic in the relocation handling code to
ensure that PREL16/32 relocations don't overflow signed quantities.
However, the same code path is used for absolute relocations, where the
interpretation is the opposite: the only current use case for absolute
relocations operating on non-native word size quantities is the CRC32
handling in the CONFIG_MODVERSIONS code, and these CRCs are unsigned
32-bit quantities, which are now being rejected by the module loader
if bit 31 happens to be set.
So let's use different ranges for quanties subject to absolute vs.
relative relocations:
- ABS16/32 relocations should be in the range [0, Uxx_MAX)
- PREL16/32 relocations should be in the range [Sxx_MIN, Sxx_MAX)
- otherwise, print an error since no other 16 or 32 bit wide data
relocations are currently supported.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Following commit 4378a7d4be ("arm64: implement syscall wrappers"), the
syscall function names gained the '__arm64_' prefix. Ensure that we
have the correct #define for redirecting a default syscall through a
wrapper.
Fixes: 4378a7d4be ("arm64: implement syscall wrappers")
Cc: <stable@vger.kernel.org> # 4.19.x-
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We do not normally access the flash on the Juno, as this
will disturb other aspects of the system, but if we choose
to do so anyways, we should set up the partitions in the
right way so we will find out what is in the flash.
The ARM Firmware Suite now has its own compatible and
proper device tree bindings to trigger discovery of the
flash contents, and Linux supports handling the new type
of AFS partitions.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
CoreSight DT bindings have been updated, thus the old compatible strings
are obsolete and the drivers will report warning if DTS uses these
obsolete strings.
This patch switches to the new bindings for CoreSight dynamic funnel,
so can dismiss warning during initialisation.
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
With most of the previous functionality now elsewhere a lot of the
headers included in this file are not needed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
There is nothing really arm64 specific in the iommu_dma_ops
implementation, so move it to dma-iommu.c and keep a lot of symbols
self-contained. Note the implementation does depend on the
DMA_DIRECT_REMAP infrastructure for now, so we'll have to make the
DMA_IOMMU support depend on it, but this will be relaxed soon.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
We now have a arch_dma_prep_coherent architecture hook that is used
for the generic DMA remap allocator, and we should use the same
interface for the dma-iommu code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
All of the callers pass current into force_sig_mceer so remove the
task parameter to make this obvious.
This also makes it clear that force_sig_mceerr passes current
into force_sig_info.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
All of the remaining callers pass current into force_sig so
remove the task parameter to make this obvious and to make
misuse more difficult in the future.
This also makes it clear force_sig passes current into force_sig_info.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
I don't think this is userspace visible but SIGKILL does not have
any si_codes that use the fault member of the siginfo union. Correct
this the simple way and call force_sig instead of force_sig_fault when
the signal is SIGKILL.
The two know places where synchronous SIGKILL are generated are
do_bad_area and fpsimd_save. The call paths to force_sig_fault are:
do_bad_area
arm64_force_sig_fault
force_sig_fault
force_signal_inject
arm64_notify_die
arm64_force_sig_fault
force_sig_fault
Which means correcting this in arm64_force_sig_fault is enough
to ensure the arm64 code is not misusing the generic code, which
could lead to maintenance problems later.
Cc: stable@vger.kernel.org
Cc: Dave Martin <Dave.Martin@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Fixes: af40ff687b ("arm64: signal: Ensure si_code is valid for all fault signals")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
merge window, but should not wait four months before they appear in
a release. I also travelled a bit more than usual in the first part
of May, which didn't help with picking up patches and reports promptly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJc6RkmAAoJEL/70l94x66DhEAH/ijCkibV9vOUu8n/lSxMjAzi
I/Y1VEaVRFuQ6u0QSjWBBg22tVsWuWiVbonJ63w3JMRwi5Q5zW9REE7EaKRAa/eC
FiFE7vTesYh6sGVwdMCwoinjMDyCp7hybvtBc608+MWhVmrdzTYtPm5N85wxIDtW
xH5Kr2mVeLC43X3vfegolmXZ1obAbZEToJvOgJrYFhnzsmVYYl182kfGtrppBoO0
XXDPuDRGpTrm6A2oADMdOv+mT9p51pHsedmHQaDGXwAGEC/BkOGKdIdBfwppEwy7
QP2NGqwkHIyghV1aCPacT6O6G6xL0i2rfvlJ7+e6o7deU4uMXAqIdQ2DbIcHy3g=
=5IW2
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"The usual smattering of fixes and tunings that came in too late for
the merge window, but should not wait four months before they appear
in a release.
I also travelled a bit more than usual in the first part of May, which
didn't help with picking up patches and reports promptly"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (33 commits)
KVM: x86: fix return value for reserved EFER
tools/kvm_stat: fix fields filter for child events
KVM: selftests: Wrap vcpu_nested_state_get/set functions with x86 guard
kvm: selftests: aarch64: compile with warnings on
kvm: selftests: aarch64: fix default vm mode
kvm: selftests: aarch64: dirty_log_test: fix unaligned memslot size
KVM: s390: fix memory slot handling for KVM_SET_USER_MEMORY_REGION
KVM: x86/pmu: do not mask the value that is written to fixed PMUs
KVM: x86/pmu: mask the result of rdpmc according to the width of the counters
x86/kvm/pmu: Set AMD's virt PMU version to 1
KVM: x86: do not spam dmesg with VMCS/VMCB dumps
kvm: Check irqchip mode before assign irqfd
kvm: svm/avic: fix off-by-one in checking host APIC ID
KVM: selftests: do not blindly clobber registers in guest asm
KVM: selftests: Remove duplicated TEST_ASSERT in hyperv_cpuid.c
KVM: LAPIC: Expose per-vCPU timer_advance_ns to userspace
KVM: LAPIC: Fix lapic_timer_advance_ns parameter overflow
kvm: vmx: Fix -Wmissing-prototypes warnings
KVM: nVMX: Fix using __this_cpu_read() in preemptible context
kvm: fix compilation on s390
...
Add ENETC 1588 timer node which is ENETC PF 4 (Physiscal Function 4).
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix incorrect LDADD instruction encoding in our disassembly macros
- Disable the broken ARM64_PSEUDO_NMI support for now
- Add workaround for Cortex-A76 CPU erratum #1463225
- Handle Cortex-A76/Neoverse-N1 erratum #1418040 w/ existing workaround
- Fix IORT build failure if IOMMU_SUPPORT=n
- Fix place-relative module relocation range checking and its
interaction with KASLR
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAlzoC8MACgkQt6xw3ITB
YzQfiAf+MXFzrAd3o7v40CnZu6ELw+ldedPh34oBjD7h6we3hroxi5Fss2nbwH0o
BmAm4Nv1/Njk5+hA7Mlp3/mRn0vcd3NDP+FyH3inLjUU7owc41thp0SKlCOfFdZk
K8sVCOeCWt7GEEPcnFsPO0nU+7f3ZKDDNBo0L+qJPxrMOTDcbQ3cIjW/ua7vQRHv
pIDGF+iJAhHeNoc1Wjq08F8Q+Dq7dYvhtokeyDivSn4NulmRvdL+z581gMmj7ExT
ARB6WtHGoOo+8UdjBJIDnXRKhJLfGexQaoAojk+IogaV0ACDtz6CuqsSIh1e5SFC
oPqRSP5ITTbXEDS5uaUW1pYlwmGTaw==
=ynUz
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull more arm64 fixes from Will Deacon:
- Fix incorrect LDADD instruction encoding in our disassembly macros
- Disable the broken ARM64_PSEUDO_NMI support for now
- Add workaround for Cortex-A76 CPU erratum #1463225
- Handle Cortex-A76/Neoverse-N1 erratum #1418040 w/ existing workaround
- Fix IORT build failure if IOMMU_SUPPORT=n
- Fix place-relative module relocation range checking and its
interaction with KASLR
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: insn: Add BUILD_BUG_ON() for invalid masks
arm64: insn: Fix ldadd instruction encoding
arm64: Kconfig: Make ARM64_PSEUDO_NMI depend on BROKEN for now
arm64: Handle erratum 1418040 as a superset of erratum 1188873
arm64/module: deal with ambiguity in PRELxx relocation ranges
ACPI/IORT: Fix build error when IOMMU_SUPPORT is disabled
arm64/kernel: kaslr: reduce module randomization range to 2 GB
arm64: errata: Add workaround for Cortex-A76 erratum #1463225
arm64: Remove useless message during oops
Detect invalid instruction masks at build time. Some versions of GCC can
warn about the situation, but not all of them, it seems.
Suggested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
GCC 8.1.0 reports that the ldadd instruction encoding, recently added to
insn.c, doesn't match the mask and couldn't possibly be identified:
linux/arch/arm64/include/asm/insn.h: In function 'aarch64_insn_is_ldadd':
linux/arch/arm64/include/asm/insn.h:280:257: warning: bitwise comparison always evaluates to false [-Wtautological-compare]
Bits [31:30] normally encode the size of the instruction (1 to 8 bytes)
and the current instruction value only encodes the 4- and 8-byte
variants. At the moment only the BPF JIT needs this instruction, and
doesn't require the 1- and 2-byte variants, but to be consistent with
our other ldr and str instruction encodings, clear the size field in the
insn value.
Fixes: 34b8ab091f ("bpf, arm64: use more scalable stadd over ldxr / stxr loop in xadd")
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Reported-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Although we merged support for pseudo-nmi using interrupt priority
masking in 5.1, we've since uncovered a number of non-trivial issues
with the implementation. Although there are patches pending to address
these problems, we're facing issues that prevent us from merging them at
this current time:
https://lkml.kernel.org/r/1556553607-46531-1-git-send-email-julien.thierry@arm.com
For now, simply mark this optional feature as BROKEN in the hope that we
can fix things properly in the near future.
Cc: <stable@vger.kernel.org> # 5.1
Cc: Julien Thierry <julien.thierry@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
KVM has helpers to handle the condition codes of trapped aarch32
instructions. These are marked __hyp_text and used from HYP, but they
aren't built by the 'hyp' Makefile, which has all the runes to avoid ASAN
and KCOV instrumentation.
Move this code to a new hyp/aarch32.c to avoid a hyp-panic when starting
an aarch32 guest on a host built with the ASAN/KCOV debug options.
Fixes: 021234ef37 ("KVM: arm64: Make kvm_condition_valid32() accessible from EL2")
Fixes: 8cebe750c4 ("arm64: KVM: Make kvm_skip_instr32 available to HYP")
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
KVM's pmu.c contains the __hyp_text needed to switch the pmu registers
between host and guest. Because this isn't covered by the 'hyp' Makefile,
it can be built with kasan and friends when these are enabled in Kconfig.
When starting a guest, this results in:
| Kernel panic - not syncing: HYP panic:
| PS:a00003c9 PC:000083000028ada0 ESR:86000007
| FAR:000083000028ada0 HPFAR:0000000029df5300 PAR:0000000000000000
| VCPU:000000004e10b7d6
| CPU: 0 PID: 3088 Comm: qemu-system-aar Not tainted 5.2.0-rc1 #11026
| Hardware name: ARM LTD ARM Juno Development Platform/ARM Juno Development Plat
| Call trace:
| dump_backtrace+0x0/0x200
| show_stack+0x20/0x30
| dump_stack+0xec/0x158
| panic+0x1ec/0x420
| panic+0x0/0x420
| SMP: stopping secondary CPUs
| Kernel Offset: disabled
| CPU features: 0x002,25006082
| Memory Limit: none
| ---[ end Kernel panic - not syncing: HYP panic:
This is caused by functions in pmu.c calling the instrumented
code, which isn't mapped to hyp. From objdump -r:
| RELOCATION RECORDS FOR [.hyp.text]:
| OFFSET TYPE VALUE
| 0000000000000010 R_AARCH64_CALL26 __sanitizer_cov_trace_pc
| 0000000000000018 R_AARCH64_CALL26 __asan_load4_noabort
| 0000000000000024 R_AARCH64_CALL26 __asan_load4_noabort
Move the affected code to a new file under 'hyp's Makefile.
Fixes: 3d91befbb3 ("arm64: KVM: Enable !VHE support for :G/:H perf event modifiers")
Cc: Andrew Murray <Andrew.Murray@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The SUNXI_WATCHDOG option is required to make the
watchdog available on Allwinner H6.
Enable this option as a module.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 has a r_watchdog similar to A64.
Declare it in the device-tree.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 has a watchog node which seems broken
on some boards.
Test has been performed on several boards.
Chen-Yu Tsai boards:
Pine H64 - H6448BA 7782 => OK
OrangePi Lite 2 - H8068BA 61C2 => KO
Martin Ayotte boards:
Pine H64 - H8069BA 6892 => OK
OrangePi 3 - HA047BA 69W2 => KO
OrangePi One Plus - H7310BA 6842 => KO
OrangePi Lite2 - H6448BA 6662 => KO
Clément Péron board:
Beelink GS1 - H7309BA 6842 => KO
As it seems not fixable for now, declare the node
but leave it disable with a comment.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add the synopsys ethernet mac controller embedded in the g12a SoC family.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
We already mitigate erratum 1188873 affecting Cortex-A76 and
Neoverse-N1 r0p0 to r2p0. It turns out that revisions r0p0 to
r3p1 of the same cores are affected by erratum 1418040, which
has the same workaround as 1188873.
Let's expand the range of affected revisions to match 1418040,
and repaint all occurences of 1188873 to 1418040. Whilst we're
there, do a bit of reformating in silicon-errata.txt and drop
a now unnecessary dependency on ARM_ARCH_TIMER_OOL_WORKAROUND.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The R_AARCH64_PREL16 and R_AARCH64_PREL32 relocations are
documented as permitting a range of [-2^15 .. 2^16), resp.
[-2^31 .. 2^32). It is also documented that this means we
cannot detect overflow in some cases, which is bad.
Since we always interpret the targets of these relocations as
signed quantities (e.g., in the ksymtab handling code), let's
tighten the overflow checks so that targets that are out of
range for our signed interpretation of the relocated quantity
get flagged.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
i.MX8MM has clock gate for SNVS module, add clock info to SNVS
RTC node for clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MM has clock gate for each GPIO bank, add clock info
to GPIO node for clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The following commit
7290d58095 ("module: use relative references for __ksymtab entries")
updated the ksymtab handling of some KASLR capable architectures
so that ksymtab entries are emitted as pairs of 32-bit relative
references. This reduces the size of the entries, but more
importantly, it gets rid of statically assigned absolute
addresses, which require fixing up at boot time if the kernel
is self relocating (which takes a 24 byte RELA entry for each
member of the ksymtab struct).
Since ksymtab entries are always part of the same module as the
symbol they export, it was assumed at the time that a 32-bit
relative reference is always sufficient to capture the offset
between a ksymtab entry and its target symbol.
Unfortunately, this is not always true: in the case of per-CPU
variables, a per-CPU variable's base address (which usually differs
from the actual address of any of its per-CPU copies) is allocated
in the vicinity of the ..data.percpu section in the core kernel
(i.e., in the per-CPU reserved region which follows the section
containing the core kernel's statically allocated per-CPU variables).
Since we randomize the module space over a 4 GB window covering
the core kernel (based on the -/+ 4 GB range of an ADRP/ADD pair),
we may end up putting the core kernel out of the -/+ 2 GB range of
32-bit relative references of module ksymtab entries that refer to
per-CPU variables.
So reduce the module randomization range a bit further. We lose
1 bit of randomization this way, but this is something we can
tolerate.
Cc: <stable@vger.kernel.org> # v4.19+
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Revisions of the Cortex-A76 CPU prior to r4p0 are affected by an erratum
that can prevent interrupts from being taken when single-stepping.
This patch implements a software workaround to prevent userspace from
effectively being able to disable interrupts.
Cc: <stable@vger.kernel.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
During an oops, we print the name of the current task and its pid twice.
We also helpfully advertise its stack limit as "0x(____ptrval____)".
Drop these useless messages.
Signed-off-by: Will Deacon <will.deacon@arm.com>
- Fix SPE probe failure when backing auxbuf with high-order pages
- Fix handling of DMA allocations from outside of the vmalloc area
- Fix generation of build-id ELF section for vDSO object
- Disable huge I/O mappings if kernel page table dumping is enabled
- A few other minor fixes (comments, kconfig etc)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAlzlRT0ACgkQt6xw3ITB
YzRGOwgArUDryBedDdkxAvjx7fk8O+qjtWctAhdPtyuXIvVLOc3tpiKlayCguF/a
clqr4qAfxswoDLHRMwhh7xdv955A2vraHQWlzvGUj2O2M4mG8RdbVJLm3NxpA09m
dufjSuFcwxcou2c4rXbSXSB4AYJXPmQJiad04VsWj68+TVehy0P45zaPcjHsPNPI
D9sTa9XhBlNa0qpJG7tP9T8FS/QP/hpWHn8v0z/DQ4QetKRTstkpwD5kmJox8WmM
Bw593bvQQ2+5q9g+z0FM3M/7yHwTJw2RLnnIb29YsW8MxM3rUeqt+FMA2OALBgbi
0m7WoTZwO9hDQuPU1DDvZUtw3iOpeg==
=buiS
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
- Fix SPE probe failure when backing auxbuf with high-order pages
- Fix handling of DMA allocations from outside of the vmalloc area
- Fix generation of build-id ELF section for vDSO object
- Disable huge I/O mappings if kernel page table dumping is enabled
- A few other minor fixes (comments, kconfig etc)
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: vdso: Explicitly add build-id option
arm64/mm: Inhibit huge-vmap with ptdump
arm64: Print physical address of page table base in show_pte()
arm64: don't trash config with compat symbol if COMPAT is disabled
arm64: assembler: Update comment above cond_yield_neon() macro
drivers/perf: arm_spe: Don't error on high-order pages for aux buf
arm64/iommu: handle non-remapped addresses in ->mmap and ->get_sgtable
Jetson Nano, Jetson TX1 and Jetson TX2 all are named "Developer Kit" and
Jetson AGX Xavier is the odd one out. It's officially also called the
"Developer Kit", not "Development Kit", so make it consistent with the
rest.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
P2888 is the internal part number for the Jetson AGX Xavier module.
Clarify that using the DT model property.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
P3310 is the internal part number for the Jetson TX2 module. Clarify
that using the DT model property.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
P2771 is the internal part number for the Jetson TX2 Developer Kit.
Clarify that using the DT model property.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the hdmitx glue device linking the SoC audio interfaces to the
embedded Synopsys hdmi controller.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
At the moment the sysnopsys hdmi i2s driver provides a single playback
DAI. Add the corresponding sound-dai-cell to the hdmi device node.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the spdif input device node and the pinctrl definition for
this capture interface g12a SoC family
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the pdm device node and the pinctrl definition for this capture
interface g12a SoC family
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the devices nodes and pinctrl definitions for the spdif outputs of
the g12a SoC family
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the devices and pinctrl definitions for the tdm interfaces of
the g12a SoC family.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the playback and capture memory interfaces of the g12a SoC family.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the audio DDR memory arbitrer of the g12a SoC family.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the 3 i2c busses present on the u200 reference design.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add pinctrl and nodes for i2c support on amlogic g12a
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Now that the AO clock controller is available, make the uarts of the
always-on domain claim the appropriate peripheral clock.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable eMMC and SDCard on the g12a sei510 board
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable eMMC and SDCard on the g12a u200 board
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add port B (sdcard) and port C (eMMC) pinctrl and controllers nodes to
the g12a DT.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add sdcard uhs modes up to DDR50 and push eMMC up to 200Mhz
With the new tuning method, these modes appear to be stable
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add UHS ddr50 mode to the nanopi k2
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Ethernet PHY documentation
(Documentation/devicetree/bindings/net/phy.txt) states that:
If the PHY reports an incorrect ID (or none at all) then the
"compatible" list may contain an entry with the correct PHY ID in the
form: "ethernet-phy-idAAAA.BBBB"
An older version of the documentation suggested that the compatible
string can be used when the PHY ID is known.
Remove the ethernet-phy-id compatible string and add a comment with the
PHY ID instead.
This is a no-op on boards which are shipped with the PHY that was
listed (= all known cases). However, if a board manufacturer decides to
ship a different PHY we will now load and use the correct driver because
we ask the PHY to identify itself.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Like order boards, order nodes by address then node names then aliases.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Like order boards, order nodes by address then node names then aliases.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
sd highspeed mode make no sense for an eMMC and HS400 is not working
at the moment.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
For some reason the vim2 is missing the clk-gate pinctrl setting all
the other board have. Just add this missing bit
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl<martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
According the datasheets, emmc v2 chips (gxbb and gxl) don't support
more that 100Mhz in UHS-1 SD modes and HS in SDIO.
Align the max-frequency to 100MHz for UHS-1 and 50MHz for HS
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Clk pin does not require bias, data strobe should be pulled low.
The rest of the pin (data and cmd) are pulled up.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
While some 3.3v eMMC 4.0 are available from libretech, Only the 1.8v 5.0
modules are recommended and supported for the aml-s905x-cc.
the 1.8v is provided by LDOs on the eMMC card, from vcc 3.3v
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The eMMC on this board is add-on module which is not mandatory. Removing
'non-removable' property should prevent some errors when booting a board
w/o an eMMC module present.
Fixes: 72fb2c8521 ("ARM64: dts: meson-gxl-s905x-libretech-cc: fixup board definition")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl<martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add support for the IR decoder input on the U200 Reference Design board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl<martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add support for the IR decoder input on the X96 Max board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl<martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Amlogic G12A SoCs uses the exact same IR decoder as previous
families, add the IR node and the pintctrl setting.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl<martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds the EE and AO PWM nodes and the possible pinctrl settings.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl<martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
In order to move away from misleadingly generic definitions of the GPIO
macros, use the Tegra186-specific prefix. These are the last remaining
occurrences. The generic definitions can be removed after this.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unnecessary blank lines do NOT help readability, so remove them.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add nvmem-cells reference to cpu and fill the OPP table with all known
OPPs.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a nvmem cell on cpu node referencing speed grade and the 1.8 Ghz
cpufreq opp.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add DT nodes for
- Two xHCI host controllers
- Two BDC Broadcom USB device controller
- Five USB PHY controllers
[xHCI0] [BDC0] [xHCI1] [BDC1]
| | | |
--------------- -----------------------
| | | | |
[SS-PHY0] [HS-PHY0] [SS-PHY1] [HS-PHY2] [HS-PHY1]
[SS-PHY0/HS-PHY0] and [SS-PHY1/HS-PHY1] are combo PHYs has one SS and
one HS PHYs. [HS-PHY2] is a single HS PHY.
xHCI use SS-PHY to detect SS devices and HS-PHY to detect HS/FS/LS
devices. BDC use SS-PHY in SS mode and HS-PHY in HS mode.
xHCI0 port1 is SS-PHY0, port2 is HS-PHY0.
xHCI1 port1 is SS-PHY1, port2 is HS-PHY2 and port3 is HS-PHY1.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add tpu device node to dtsi for TPU support on r8a7795 SoC.
Signed-off-by: Cao Van Dong <cv-dong@jinso.co.jp>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add tpu device node to dtsi for TPU support on r8a77965 SoC.
Signed-off-by: Cao Van Dong <cv-dong@jinso.co.jp>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add tpu device node to dtsi for TPU support on r8a7796 SoC.
Signed-off-by: Cao Van Dong <cv-dong@jinso.co.jp>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds description of TI WL1837 and links interfaces
to communicate with the IC, namely the SDIO interface to WLAN.
Signed-off-by: Spyridon Papageorgiou <spapageorgiou@de.adit-jv.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The ports node of vin4 only has one sub-node and thus does
not need #address-cells/#size-cells and the sub-node does
not need an exit.
This addresses the following warning:
# make dtbs W=1
...
arch/arm64/boot/dts/renesas/r8a77995-draak.dts:492.8-503.4: Warning (graph_child_address): /soc/video@e6ef4000/ports: graph node has single child node 'port@0', #address-cells/#size-cells are not necessary
Fixes: 6a0942c20f ("arm64: dts: renesas: draak: Describe CVBS input")
Cc: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
The CAT874 board pushes sound via I2S over SSI0 into the
TDA19988BET chip.
This commit wires things up so that we can get sound out of
the HDMI interface.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The CAT874 board comes with a HDMI connector, managed by
a TDA19988BET chip, connected to the RZ/G2E SoC via DPAD.
This patch adds the necessary support to the board DT.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add IPMMU-DS0 to the Ethernet-AVB device node.
Based on work by Magnus Damm for the r8a7795.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hook up r8a774a1 Audio-DMAC nodes to the IPMMU-MP.
Based on work for the r8a7795 by Magnus Damm.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hook up r8a774a1 DMAC nodes to the IPMMUs. In particular SYS-DMAC0
gets tied to IPMMU-DS0, and SYS-DMAC1 and SYS-DMAC2 get tied to IPMMU-DS1.
Based on work for the r8a7796 by Magnus Damm.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a774a1 has a single FDP1 instance similar to r8a7796.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the DU device to r8a774a1.dtsi in a disabled state.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a774a1 soc has 5 VSP instances similar to r8a7796.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The EK874 board comes with a TDA19988 chip on board, therefore
enable it in the defconfig.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The TERES-I has internal speakers (left, right), internal microphone
and a headset combo jack (headphones + mic), "CTIA" (android) pinout.
The headphone and mic detect lines of the A64 are connected properly,
but AFAIK currently unsupported by the driver.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Bananapi M64 has a micro-USB connector with USB OTG support (that
is already enabled). VBUS from this connector is wired to the PMIC's
VBUS input.
Enable the PMIC's USB power supply on this board, and also hook it up
to the USB PHY.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The AXP803 has a VBUS power input. Add a device node for it,
now that we support it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The AP6212 is based on the Broadcom BCM43430 or BCM43438. The WiFi side
identifies as BCM43430, while the Bluetooth side identifies as BCM43438.
WiFi is connected to mmc1 and the Bluetooth side is connected to UART1
in a 4 wire configuration. Same as the WiFi side, due to being the same
chip and package, DLDO2 provides overall power via VBAT, and DLDO4
provides I/O power via VDDIO. The RTC clock output provides the LPO low
power clock at 32.768 kHz.
This patch enables WiFi and Bluetooth on OrangePi Win boards and adds
missing LPO clock on the WiFi side. PCM connection also exists for
Bluetooth audio, but it's not used here.
Bluetooth UART speed is set to 1.5 MBaud in order to be able transmit
audio. While module supports even higher speeds, currently sunxi clock
driver doesn't support higher speed.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Allwinner H6 SoC features tweakable VCC for PC, PD, PG, PL and PM
banks.
This patch adds supplies for these banks except PL bank. PL bank is
where PMIC is attached, and currently if a PMIC regulator is added
for it a dependency loop will happen.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Goodix GT911 CTP is bound with Oceanic 5205 5inMFD board.
The CTP connected to board with,
- SDA, SCK from i2c0
- GPIO-LD0 as AVDD28 supply
- PH4 gpio as interrupt pin
- PH11 gpio as reset pin
- X axis is inverted
- Y axis is inverted
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add Goodix GT5663 capacitive touch controller node on
Amarula A64-Relic board.
The CTP connected to board with,
- SDA, SCK from i2c1
- GPIO-LD0 as AVDD28 supply
- PH4 gpio as interrupt pin
- PH8 gpio as reset pin
- X axis is inverted
- Y axis is inverted
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
There is only one pinmuxing available for each I2C controller.
So, move pinctrl for i2c0, i2c1 from board dts files into SoC dtsi.
By moving these pinctrls the i2c1 node from Nanopi A64 just have a
status, which is disabled already so remove the entire node from it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Sid contains speedbin information and temperature sensor
calibration information and more, which are important for SOC.
This patch enables CONFIG_NVMEM_SUNXI_SID by default.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The BUCK2 regulator is used for cpufreq voltage control, otherwise
configuration is mostly static.
This uses the newly-implemented rohm,reset-snvs-powered property to
properly handle the SNVS state of imx8mm.
Between BD71837 and BD71847 the BUCK3/4 regulators were removed but
datasheet and board schematics kept the names for BUCK5/6/7/8. The
driver however renumbered 5/6/7/8 to 3/4/5/6. Use the names from DT
bindings and add comments to signal this.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-By: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
During randconfig builds, I occasionally run into an invalid configuration
drivers/soc/imx/soc-imx8.o: In function `imx8_soc_init':
soc-imx8.c:(.init.text+0x144): undefined reference to `soc_device_register'
while CONFIG_SOC_BUS is not set, the building failed like this. This patch
selects SOC_BUS to fix it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: a7e26f356c ("soc: imx: Add generic i.MX8 SoC driver")
Suggested-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a node for the irqsteer interrupt controller found on the iMX8MQ
SoC.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The LS1028A has a LCD controller and Displayport interface that
connects to eDP and Displayport connectors on the LS1028A board.
This patch enables the LCD controller driver on the LS1028A.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Wen He <wen.he_1@nxp.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable mfd and regulator driver for PMIC found on imx8mm-evk boards
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The current lpi2c driver can work on imx8 chips so lets enable it. Also
enable few i2c peripherals found on imx8qxp-mek I2C (some were already
used for other boards).
Sensors enabled as modules because not required for boot.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Basic imx8mm support is already available in linux-next just not
enabled in arm64 defconfig. With this patch imx8mm-evk can boot.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MQ needs it for RTC support.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable CONFIG_IMX_SC_WDT as module to support i.MX system
controller watchdog.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable the CONFIG_SPI_IMX option so that i.MX8M can use the
imx spi driver by default.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable SPI1 exposed on both Low and High speed expansion connectors
of Ficus. SPI1 has 3 different chip selects wired as below:
CS0 - Serial Flash (unpopulated)
CS1 - Low Speed expansion
CS2 - High Speed expansion
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable SPI0 and SPI4 exposed on the Low and High speed expansion
connectors of Rock960.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pull IRQ chip updates from Ingo Molnar:
"A late irqchips update:
- New TI INTR/INTA set of drivers
- Rewrite of the stm32mp1-exti driver as a platform driver
- Update the IOMMU MSI mapping API to be RT friendly
- A number of cleanups and other low impact fixes"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
iommu/dma-iommu: Remove iommu_dma_map_msi_msg()
irqchip/gic-v3-mbi: Don't map the MSI page in mbi_compose_m{b, s}i_msg()
irqchip/ls-scfg-msi: Don't map the MSI page in ls_scfg_msi_compose_msg()
irqchip/gic-v3-its: Don't map the MSI page in its_irq_compose_msi_msg()
irqchip/gicv2m: Don't map the MSI page in gicv2m_compose_msi_msg()
iommu/dma-iommu: Split iommu_dma_map_msi_msg() in two parts
genirq/msi: Add a new field in msi_desc to store an IOMMU cookie
arm64: arch_k3: Enable interrupt controller drivers
irqchip/ti-sci-inta: Add msi domain support
soc: ti: Add MSI domain bus support for Interrupt Aggregator
irqchip/ti-sci-inta: Add support for Interrupt Aggregator driver
dt-bindings: irqchip: Introduce TISCI Interrupt Aggregator bindings
irqchip/ti-sci-intr: Add support for Interrupt Router driver
dt-bindings: irqchip: Introduce TISCI Interrupt router bindings
gpio: thunderx: Use the default parent apis for {request,release}_resources
genirq: Introduce irq_chip_{request,release}_resource_parent() apis
firmware: ti_sci: Add helper apis to manage resources
firmware: ti_sci: Add RM mapping table for am654
firmware: ti_sci: Add support for IRQ management
firmware: ti_sci: Add support for RM core ops
...
This is some material that we picked up into our tree late. Most of it
are smaller fixes and additions, some defconfig updates due to recent
development, etc.
Code-wise the largest portion is a series of PM updates for the at91
platform, and those have been in linux-next a while through the at91
tree before we picked them up.
-----BEGIN PGP SIGNATURE-----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=XCCp
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC late updates from Olof Johansson:
"This is some material that we picked up into our tree late. Most of it
are smaller fixes and additions, some defconfig updates due to recent
development, etc.
Code-wise the largest portion is a series of PM updates for the at91
platform, and those have been in linux-next a while through the at91
tree before we picked them up"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (29 commits)
arm64: dts: sprd: Add clock properties for serial devices
Opt out of scripts/get_maintainer.pl
ARM: ixp4xx: Remove duplicated include from common.c
soc: ixp4xx: qmgr: Fix an NULL vs IS_ERR() check in probe
arm64: tegra: Disable XUSB support on Jetson TX2
arm64: tegra: Enable SMMU translation for PCI on Tegra186
arm64: tegra: Fix insecure SMMU users for Tegra186
arm64: tegra: Select ARM_GIC_PM
amba: tegra-ahb: Mark PM functions as __maybe_unused
ARM: dts: logicpd-som-lv: Fix MMC1 card detect
ARM: mvebu: drop return from void function
ARM: mvebu: prefix coprocessor operand with p
ARM: mvebu: drop unnecessary label
ARM: mvebu: fix a leaked reference by adding missing of_node_put
ARM: socfpga_defconfig: enable LTC2497
ARM: mvebu: kirkwood: remove error message when retrieving mac address
ARM: at91: sama5: make ov2640 as a module
ARM: OMAP1: ams-delta: fix early boot crash when LED support is disabled
ARM: at91: remove HAVE_FB_ATMEL for sama5 SoC as they use DRM
soc/fsl/qe: Fix an error code in qe_pin_request()
...
* POWER: support for direct access to the POWER9 XIVE interrupt controller,
memory and performance optimizations.
* x86: support for accessing memory not backed by struct page, fixes and refactoring
* Generic: dirty page tracking improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJc3qV/AAoJEL/70l94x66Dn3QH/jX1Bn0P/RZAIt4w0SySklSg
PqxUKDyBQqB9vN9Qeb9jWXAKPH2CtM3+up/rz7oRnBWp7qA6vXcC/R/QJYAvzdXE
nklsR/oYCsflR1KdlVYuDvvPCPP2fLBU5zfN83OsaBQ8fNRkm3gN+N5XQ2SbXbLy
Mo9tybS4otY201UAC96e8N0ipwwyCRpDneQpLcl+F5nH3RBt63cVbs04O+70MXn7
eT4I+8K3+Go7LATzT8hglD21D/7uvE31qQb6yr5L33IfhU4GB51RZzBXTNaAdY8n
hT1rMrRkAMAFWYZPQDfoMadjWU3i5DIfstKjDxOr9oTfuOEp5Z+GvJwvVnUDg1I=
=D0+p
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"ARM:
- support for SVE and Pointer Authentication in guests
- PMU improvements
POWER:
- support for direct access to the POWER9 XIVE interrupt controller
- memory and performance optimizations
x86:
- support for accessing memory not backed by struct page
- fixes and refactoring
Generic:
- dirty page tracking improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (155 commits)
kvm: fix compilation on aarch64
Revert "KVM: nVMX: Expose RDPMC-exiting only when guest supports PMU"
kvm: x86: Fix L1TF mitigation for shadow MMU
KVM: nVMX: Disable intercept for FS/GS base MSRs in vmcs02 when possible
KVM: PPC: Book3S: Remove useless checks in 'release' method of KVM device
KVM: PPC: Book3S HV: XIVE: Fix spelling mistake "acessing" -> "accessing"
KVM: PPC: Book3S HV: Make sure to load LPID for radix VCPUs
kvm: nVMX: Set nested_run_pending in vmx_set_nested_state after checks complete
tests: kvm: Add tests for KVM_SET_NESTED_STATE
KVM: nVMX: KVM_SET_NESTED_STATE - Tear down old EVMCS state before setting new state
tests: kvm: Add tests for KVM_CAP_MAX_VCPUS and KVM_CAP_MAX_CPU_ID
tests: kvm: Add tests to .gitignore
KVM: Introduce KVM_CAP_MANUAL_DIRTY_LOG_PROTECT2
KVM: Fix kvm_clear_dirty_log_protect off-by-(minus-)one
KVM: Fix the bitmap range to copy during clear dirty
KVM: arm64: Fix ptrauth ID register masking logic
KVM: x86: use direct accessors for RIP and RSP
KVM: VMX: Use accessors for GPRs outside of dedicated caching logic
KVM: x86: Omit caching logic for always-available GPRs
kvm, x86: Properly check whether a pfn is an MMIO or not
...
Pull more vfs mount updates from Al Viro:
"Propagation of new syscalls to other architectures + cosmetic change
from Christian (fscontext didn't follow the convention for anon inode
names)"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
uapi: Wire up the mount API syscalls on non-x86 arches [ver #2]
uapi, x86: Fix the syscall numbering of the mount API syscalls [ver #2]
uapi, fsopen: use square brackets around "fscontext" [ver #2]
We've introduced power management logics for the Spreadtrum serial
controller by commit 062ec2774c8a ("serial: sprd: Add power management
for the Spreadtrum serial controller"), thus add related clock properties
to support this feature.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Christoph Hellwig writes:
This is a series doing two somewhat interwinded things. It improves
the asm-generic nommu uaccess helper to optionally be entirely generic
and not require any arch helpers for the actual uaccess. For the
generic uaccess.h to actually be generically useful I also had to kill
off the mess we made of <asm/segment.h>, which really shouldn't exist
on most architectures.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=X2CH
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-nommu' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull nommu generic uaccess updates from Arnd Bergmann:
"asm-generic: kill <asm/segment.h> and improve nommu generic uaccess helpers
Christoph Hellwig writes:
This is a series doing two somewhat interwinded things. It improves
the asm-generic nommu uaccess helper to optionally be entirely
generic and not require any arch helpers for the actual uaccess.
For the generic uaccess.h to actually be generically useful I also
had to kill off the mess we made of <asm/segment.h>, which really
shouldn't exist on most architectures"
* tag 'asm-generic-nommu' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: optimize generic uaccess for 8-byte loads and stores
asm-generic: provide entirely generic nommu uaccess
arch: mostly remove <asm/segment.h>
asm-generic: don't include <asm/segment.h> from <asm/uaccess.h>
This contains one patch to disable the recently added XUSB support on
Jetson TX2 which is reported to cause boot and CPU hotplug failures in
some cases and doesn't allow the core power rail to be switched off.
Furthermore there are some changes to enable IOMMU support on more
devices. This is needed in order to prevent these devices from breaking
with the policy change in the ARM SMMU driver to break insecure devices
that is currently headed for v5.2.
-----BEGIN PGP SIGNATURE-----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=a/kH
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.2-arm64-dt-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/late
arm64: tegra: Device tree fixes for v5.2-rc1
This contains one patch to disable the recently added XUSB support on
Jetson TX2 which is reported to cause boot and CPU hotplug failures in
some cases and doesn't allow the core power rail to be switched off.
Furthermore there are some changes to enable IOMMU support on more
devices. This is needed in order to prevent these devices from breaking
with the policy change in the ARM SMMU driver to break insecure devices
that is currently headed for v5.2.
* tag 'tegra-for-5.2-arm64-dt-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Disable XUSB support on Jetson TX2
arm64: tegra: Enable SMMU translation for PCI on Tegra186
arm64: tegra: Fix insecure SMMU users for Tegra186
Signed-off-by: Olof Johansson <olof@lixom.net>
This enables the ARM_GIC_PM driver by default for Tegra in order to
increase build coverage.
-----BEGIN PGP SIGNATURE-----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=PgVG
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.2-arm64-soc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/late
arm64: tegra: Core fixes for v5.2-rc1
This enables the ARM_GIC_PM driver by default for Tegra in order to
increase build coverage.
* tag 'tegra-for-5.2-arm64-soc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Select ARM_GIC_PM
Signed-off-by: Olof Johansson <olof@lixom.net>
- Mostly the usual churn due to options being reordered or not added
in the right locations.
- Some various enabling of new drivers, etc.
... i.e. the usual updates, nothing particularly sticks out.
-----BEGIN PGP SIGNATURE-----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=IKfA
-----END PGP SIGNATURE-----
Merge tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC defconfig updates from Olof Johansson:
"Mostly the usual churn due to options being reordered or not added in
the right locations.
Some various enabling of new drivers, etc.
... i.e. the usual updates, nothing particularly sticks out"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (23 commits)
arm64: defconfig: Update UFSHCD for Hi3660 soc
ARM: multi_v7_defconfig: Enable support for STPMIC1
ARM: multi_v7_defconfig: Enable missing drivers for supported Chromebooks
arm64: defconfig: enable mv-xor driver
ARM: Enable Trusted Foundations for multiplatform ARM v7
ARM: tegra: Enable Trusted Foundations by default
ARM: tegra: Update default configuration for v5.1-rc1
ARM: multi_v7_defconfig: Update for moved options
ARM: multi_v7_defconfig: Update for dropped options
ARM: shmobile: Enable USB [EO]HCI HCD PLATFORM support in shmobile_defconfig
ARM: shmobile: Enable PHY_RCAR_GEN3_USB2 in shmobile_defconfig
ARM: qcom_defconfig: add options for LG Nexus 5 phone
arm64: defconfig: include the Agilex platform to the arm64 defconfig
arm64: defconfig: Add PWM Fan support
arm64: defconfig: Enable Tegra HDA support
ARM: multi_v7_defconfig: Enable support for CFI NOR FLASH
ARM: shmobile: defconfig: Enable support for CFI NOR FLASH
ARM: shmobile: defconfig: Refresh for v5.1-rc1
ARM: multi_v7_defconfig: enable the Amlogic Meson ADC and eFuse drivers
arm64: defconfig: enable fpga and service layer
...
Wire up the mount API syscalls on non-x86 arches.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
SoC updates, mostly refactorings and cleanups of old legacy platforms.
Major themes this release:
- Conversion of ixp4xx to a modern platform (drivers, DT, bindings)
- Moving some of the ep93xx headers around to get it closer to multiplatform enabled.
- Cleanups of Davinci
This tag also contains a few patches that were queued up as fixes before
5.1 but I didn't get sent in before release.
-----BEGIN PGP SIGNATURE-----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=pUeO
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC updates, mostly refactorings and cleanups of old legacy platforms.
Major themes this release:
- Conversion of ixp4xx to a modern platform (drivers, DT, bindings)
- Moving some of the ep93xx headers around to get it closer to
multiplatform enabled.
- Cleanups of Davinci
This also contains a few patches that were queued up as fixes before
5.1 but I didn't get sent in before release"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
ARM: debug-ll: add default address for digicolor
ARM: u300: regulator: add MODULE_LICENSE()
ARM: ep93xx: move private headers out of mach/*
ARM: ep93xx: move pinctrl interfaces into include/linux/soc
ARM: ep93xx: keypad: stop using mach/platform.h
ARM: ep93xx: move network platform data to separate header
ARM: stm32: add AMBA support for stm32 family
MAINTAINERS: update arch/arm/mach-davinci
ARM: rockchip: add missing of_node_put in rockchip_smp_prepare_pmu
ARM: dts: Add queue manager and NPE to the IXP4xx DTSI
soc: ixp4xx: qmgr: Add DT probe code
soc: ixp4xx: qmgr: Add DT bindings for IXP4xx qmgr
soc: ixp4xx: npe: Add DT probe code
soc: ixp4xx: Add DT bindings for IXP4xx NPE
soc: ixp4xx: qmgr: Pass resources
soc: ixp4xx: Remove unused functions
soc: ixp4xx: Uninline several functions
soc: ixp4xx: npe: Pass addresses as resources
ARM: ixp4xx: Turn the QMGR into a platform device
ARM: ixp4xx: Turn the NPE into a platform device
...
Commit 691efbedc6 ("arm64: vdso: use $(LD) instead of $(CC) to
link VDSO") switched to using LD explicitly. The --build-id option
needs to be passed explicitly, similar to x86. Add this option.
Fixes: 691efbedc6 ("arm64: vdso: use $(LD) instead of $(CC) to link VDSO")
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
[will: drop redundant use of 'call ld-option' as requested by Masahiro]
Signed-off-by: Will Deacon <will.deacon@arm.com>
The arm64 ptdump code can race with concurrent modification of the
kernel page tables. At the time this was added, this was sound as:
* Modifications to leaf entries could result in stale information being
logged, but would not result in a functional problem.
* Boot time modifications to non-leaf entries (e.g. freeing of initmem)
were performed when the ptdump code cannot be invoked.
* At runtime, modifications to non-leaf entries only occurred in the
vmalloc region, and these were strictly additive, as intermediate
entries were never freed.
However, since commit:
commit 324420bf91 ("arm64: add support for ioremap() block mappings")
... it has been possible to create huge mappings in the vmalloc area at
runtime, and as part of this existing intermediate levels of table my be
removed and freed.
It's possible for the ptdump code to race with this, and continue to
walk tables which have been freed (and potentially poisoned or
reallocated). As a result of this, the ptdump code may dereference bogus
addresses, which could be fatal.
Since huge-vmap is a TLB and memory optimization, we can disable it when
the runtime ptdump code is in use to avoid this problem.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Fixes: 324420bf91 ("arm64: add support for ioremap() block mappings")
Acked-by: Ard Biesheuvel <ard.biesheuvel@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
- guest SVE support
- guest Pointer Authentication support
- Better discrimination of perf counters between host and guests
-----BEGIN PGP SIGNATURE-----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=fjph
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm updates for 5.2
- guest SVE support
- guest Pointer Authentication support
- Better discrimination of perf counters between host and guests
Conflicts:
include/uapi/linux/kvm.h
Kishon Vijay Abraham I