Commit Graph

15 Commits

Author SHA1 Message Date
Marcel Holtmann a418b893a6 Bluetooth: Enable per-module dynamic debug messages
With the introduction of CONFIG_DYNAMIC_PRINTK_DEBUG it is possible to
allow debugging without having to recompile the kernel. This patch turns
all BT_DBG() calls into pr_debug() to support dynamic debug messages.

As a side effect all CONFIG_BT_*_DEBUG statements are now removed and
some broken debug entries have been fixed.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-11-30 12:17:28 +01:00
Marcel Holtmann 5ddd4a6068 Bluetooth: Allow SCO audio with Asus WL-BTD202 dongle
This patch allows the Asus WL-BTD202 dongle to be used with a mono
headset without having to specify "options btusb force_scofix=1".

Based on a patch from Guillaume Bedot <littletux@zarb.org>

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-11-30 12:17:27 +01:00
Marcel Holtmann 7a9d402053 Bluetooth: Send HCI Reset command by default on device initialization
The Bluetooth subsystem was not using the HCI Reset command when doing
device initialization. The Bluetooth 1.0b specification was ambiguous
on how the device firmware was suppose to handle it. Almost every device
was triggering a transport reset at the same time. In case of USB this
ended up in disconnects from the bus.

All modern Bluetooth dongles handle this perfectly fine and a lot of
them actually require that HCI Reset is sent. If not then they are
either stuck in their HID Proxy mode or their internal structures for
inquiry and paging are not correctly setup.

To handle old and new devices smoothly the Bluetooth subsystem contains
a quirk to force the HCI Reset on initialization. However maintaining
such a quirk becomes more and more complicated. This patch turns the
logic around and lets the old devices disable the HCI Reset command.

The only device where the HCI_QUIRK_NO_RESET is still needed are the
original Digianswer devices and dongles with an early CSR firmware.

CSR reported that they fixed this for version 12 firmware. The last
official release of version 11 firmware is build ID 115. The first
version 12 candidate was build ID 117.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-11-30 12:17:26 +01:00
Marcel Holtmann 6a88adf2ad Bluetooth: Add suspend/resume support to btusb driver
During suspend it is important that all URBs are cancelled and then on
resume re-submitted. This gives initial suspend/resume support.

Based on initial work from Oliver Neukum <oneukum@suse.de>

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-11-30 12:17:14 +01:00
Marcel Holtmann a780efa812 Bluetooth: Handle bulk URBs in btusb driver from notify callback
With the addition of usb_unlink_anchored_urbs() it is possible to fully
control the bulk URBs from the notify callback. There is no need to
schedule work and so only do this for the ISOC URBs.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-11-30 12:17:12 +01:00
Marcel Holtmann 2eda66f4a0 Bluetooth: Add fine grained mem_flags usage to btusb driver
The URB submission routines need more fine grained control for the
mem_flags used by kmalloc(), usb_alloc_urb() and usb_submit_urb() to
better support different caller situations. Add a mem_flags parameter
and give the caller full control.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-11-30 12:17:10 +01:00
Marcel Holtmann 1305e9e799 [Bluetooth] Add reset quirk for A-Link BlueUSB21 dongle
The new A-Link Bluetooth dongle is another one based on the BCM2046 chip
from Broadcom and it also needs to send HCI_Reset before it becomes fully
operational. Without the quirk it will show a lot of I/O errors.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-10-06 12:22:52 +02:00
Marcel Holtmann 4f62f6cb93 [Bluetooth] Add reset quirk for new Targus and Belkin dongles
Targus and Belkin have come out with new Bluetooth 2.1 capable dongles
using the latest BCM2046 chip from Broadcom. Both of them are so called
HID proxy dongles and they need to send HCI_Reset before they become
fully operational.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-10-06 12:22:51 +02:00
Marcel Holtmann 36010ff678 [Bluetooth] Fix double frees on error paths of btusb and bpa10x drivers
The transfer buffer of an URB will be automatically freed when using
the URB_FREE_BUFFER transfer_flag. So the extra calls to kfree() will
cause a double free.

Reported-by: Justin Mattock <justinmattock@gmail.com>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-10-06 12:22:51 +02:00
Marcel Holtmann 5fbcd260c2 [Bluetooth] Fix USB disconnect handling of btusb driver
The USB transport specification for Bluetooth splits the ACL and SCO
handling into two separate interfaces. In Linux it possible to probe
and disconnect these interfaces independently. So make sure that both
interfaces are tightly bound together.

This fixes the suspend regression that some people have expierenced.

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-09-23 00:16:36 +02:00
Marcel Holtmann e8c3c3d22b [Bluetooth] Fix wrong URB handling of btusb driver
The btusb driver contains two typos that result in some buggy behavior,
but the impact is not immediately visible.

During initialization the submitting of interrupt URBs might fail and
then make sure to remove the correct flag and not one of the hci_dev
flags.

When closing down the interface make sure to kill the anchor for the
ISOC URBs and not kill the interrupt URBs twice.

Also cancel any scheduled work when closing down the interface.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-09-23 00:16:36 +02:00
Marcel Holtmann bdbef3d696 [Bluetooth] Fix I/O errors on MacBooks with Broadcom chips
The newer MacBooks contain a Broadcom based Bluetooth chip and to make
this work properly, HCI_Reset must be send first. If HCI_Reset is not
used then a lot of I/O errors show up and its triggers packets from
non-existent ACL links.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-09-23 00:16:35 +02:00
Marcel Holtmann 9bfa35fe42 [Bluetooth] Add SCO support to btusb driver
The new generic driver for Bluetooth USB devices was missing proper
SCO support. The driver now claims the second interface for these USB
devices to allow the flow of SCO packets. It also handles switching
of the alternate setting and re-submission of isochronous URBs.

The btusb driver is now a full replacement for hci_usb and thus the
experimental tag has been removed and this driver is promoted as
preferred one.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-08-18 13:23:52 +02:00
Marcel Holtmann cfeb414537 [Bluetooth] Add full quirk implementation for btusb driver
This implements all the quirk handling from the hci_usb driver to the
new btusb driver.

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-08-07 22:26:56 +02:00
Marcel Holtmann 5e23b923da [Bluetooth] Add generic driver for Bluetooth USB devices
This patch adds a new generic driver for Bluetooth USB devices. This
driver is still experimental at this point, but it is cleaner and
easier to maintain than the current Bluetooth USB driver. It is a
much better starting point for power management improvements.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2007-10-22 02:59:46 -07:00