Migrate sparc drivers to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.
This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.
We weren't doing anything which switching to few clockevent modes and so
their callbacks aren't implemented.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
are flagged as __cpuinit -- so if we remove the __cpuinit from
arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
content into no-ops as early as possible, since that will get rid
of these warnings. In any case, they are temporary and harmless.
This removes all the arch/sparc uses of the __cpuinit macros from
C files and removes __CPUINIT from assembly files. Note that even
though arch/sparc/kernel/trampoline_64.S has instances of ".previous"
in it, they are all paired off against explicit ".section" directives,
and not implicitly paired with __CPUINIT (unlike mips and arm were).
[1] https://lkml.org/lkml/2013/5/20/589
Cc: "David S. Miller" <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Introduce a common smp_callin() function to call
from trampoline_32.S.
Add platform specific functions to handle the
platform details.
This is in preparation for a patch that will
unify the smp boot stuff for all architectures.
sparc32 was significantly different to warrant
this patch in preparation.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull smp hotplug cleanups from Thomas Gleixner:
"This series is merily a cleanup of code copied around in arch/* and
not changing any of the real cpu hotplug horrors yet. I wish I'd had
something more substantial for 3.5, but I underestimated the lurking
horror..."
Fix up trivial conflicts in arch/{arm,sparc,x86}/Kconfig and
arch/sparc/include/asm/thread_info_32.h
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (79 commits)
um: Remove leftover declaration of alloc_task_struct_node()
task_allocator: Use config switches instead of magic defines
sparc: Use common threadinfo allocator
score: Use common threadinfo allocator
sh-use-common-threadinfo-allocator
mn10300: Use common threadinfo allocator
powerpc: Use common threadinfo allocator
mips: Use common threadinfo allocator
hexagon: Use common threadinfo allocator
m32r: Use common threadinfo allocator
frv: Use common threadinfo allocator
cris: Use common threadinfo allocator
x86: Use common threadinfo allocator
c6x: Use common threadinfo allocator
fork: Provide kmemcache based thread_info allocator
tile: Use common threadinfo allocator
fork: Provide weak arch_release_[task_struct|thread_info] functions
fork: Move thread info gfp flags to header
fork: Remove the weak insanity
sh: Remove cpu_idle_wait()
...
Use sparc_config to hold the last two function pointers. There was no
point generating dedicated _ops structures only for these.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I ended up renaming set_cpu_int to send_ipi to
be consistent all way around.
send_ipi was moved to the *_smp.c files so
we could call the relevant method direct,
without any _ops indirection.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the last non-trivial user of btfixup.
Like sparc64, use a special patch section to resolve the various
implementations of how to read the current CPU's ID when we don't
have current_thread_info()->cpu necessarily available.
Signed-off-by: David S. Miller <davem@davemloft.net>
Tested-by: Sam Ravnborg <sam@ravnborg.org>
This eliminated most of the remaining users of btfixup.
There are some complications because of the special cases we
have for sun4d, leon, and some flavors of viking.
It was found that there are no cases where a flush_page_for_dma
method was not hooked up to something, so the "noflush" iommu
methods were removed.
Add some documentation to the viking_sun4d_smp_ops to describe exactly
the hardware bug which causes us to need special TLB flushing on
sun4d.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Tested-by: David S. Miller <davem@davemloft.net>
Link: http://lkml.kernel.org/r/20120420124558.055198736@linutronix.de
The kernel uses l14 timers as clockevents. l10 timer is used
as clocksource if platform master_l10_counter isn't constantly
zero. The clocksource is continuous, so it's possible to use
high resolution timers. l10 timer is also used as clockevent
on UP configurations.
This realization is for sun4m, sun4d, sun4c, microsparc-IIep
and LEON platforms. The appropriate LEON changes was made by
Konrad Eisele.
In case of sun4m's oneshot mode, profile irq is zeroed in
smp4m_percpu_timer_interrupt(). It is maybe
needless (double, triple etc overflow does nothing).
sun4d is able to have oneshot mode too, but I haven't
any way to test it. So code of its percpu timer handler
is made as much equal to the current code as possible.
The patch is tested on sun4m box in SMP mode by me,
and tested by Konrad on leon in up mode (leon smp
is broken atm - due to other reasons).
Signed-off-by: Tkhai Kirill <tkhai@yandex.ru>
Tested-by: Konrad Eisele <konrad@gaisler.com> [leon up]
[sam: revised patch to provide generic support for leon]
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapt new API. Almost change is trivial, most important change are to
remove following like =operator.
cpumask_t cpu_mask = *mm_cpumask(mm);
cpus_allowed = current->cpus_allowed;
Because cpumask_var_t is =operator unsafe. These usage might prevent
kernel core improvement.
No functional change.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the three IPIs (resched, single and cpu-mask) generation
and interrupt handler catch. The sun4m has 15 soft-IRQs and three
of them is used with this patch, the three IPIs was previously
implemented with the cross-call IRQ15 which does not work with
locking routines such as spinlocks because IRQ15 is NMI, it may
cause deadlock.
The IRQ trap handler code assumes (in the same spritit as the old
it seems) that hard interrupts will be generated until handled
(level), when a IRQ happens the IRQ pending register is checked
for pending soft-IRQs. When both hard and soft IRQ happens at the
same time only soft-IRQs are handled.
The old code implemented a soft-IRQ traphandler at IRQ14 which
called smp_reschedule_irq which in turn called set_need_resched.
It seems to be an old relic and is replaced with the interrupt
traphander exit code RESTORE_ALL, it calls schedule() when
appropriate.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We did a cpu_probe() call each time a CPU got online - which
only effect was to save latest CPU/FPU info for use by show_cpuinfo().
Use same setup as for sparc64 where we probe for this info during startup,
and only once.
This allowed us to annotate a few functions __init which again
fixed the following section mismatch warnings:
WARNING: vmlinux.o(.text+0x65f0): Section mismatch in reference from the function set_cpu_and_fpu() to the (unknown reference) .init.rodata:(unknown)
WARNING: vmlinux.o(.text+0x65f8): Section mismatch in reference from the function set_cpu_and_fpu() to the (unknown reference) .init.rodata:(unknown)
WARNING: vmlinux.o(.text+0x664c): Section mismatch in reference from the function set_cpu_and_fpu() to the variable .init.rodata:manufacturer_info
WARNING: vmlinux.o(.text+0x6650): Section mismatch in reference from the function set_cpu_and_fpu() to the variable .init.rodata:manufacturer_info
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conversion of sparc32 to genirq is based on original work done
by David S. Miller.
Daniel Hellstrom has helped in the conversion and implemented
the shutdowm functionality.
Marcel van Nies <morcles@gmail.com> has tested this on Sparc Station 20
Test status:
sun4c - not tested
sun4m,pci - not tested
sun4m,sbus - tested (Sparc Classic, Sparc Station 5, Sparc Station 20)
sun4d - not tested
leon - tested on various combinations of leon boards,
including SMP variants
generic
Introduce use of GENERIC_HARDIRQS and GENERIC_IRQ_SHOW
Allocate 64 IRQs - which is enough even for SS2000
Use a table of irq_bucket to maintain uses IRQs
irq_bucket is also used to chain several irq's that
must be called when the same intrrupt is asserted
Use irq_link to link a interrupt source to the irq
All plafforms must now supply their own build_device_irq method
handler_irq rewriten to use generic irq support
floppy
Read FLOPPY_IRQ from platform device
Use generic request_irq to register the floppy interrupt
Rewrote sparc_floppy_irq to use the generic irq support
pcic:
Introduce irq_chip
Store mask in chip_data for use in mask/unmask functions
Add build_device_irq for pcic
Use pcic_build_device_irq in pci_time_init
allocate virtual irqs in pcic_fill_irq
sun4c:
Introduce irq_chip
Store mask in chip_data for use in mask/unmask functions
Add build_device_irq for sun4c
Use sun4c_build_device_irq in sun4c_init_timers
sun4m:
Introduce irq_chip
Introduce dedicated mask/unmask methods
Introduce sun4m_handler_data that allow easy access to necessary
data in the mask/unmask functions
Add a helper method to enable profile_timer (used from smp)
Added sun4m_build_device_irq
Use sun4m_build_device_irq in sun4m_init_timers
TODO:
There is no replacement for smp_rotate that always scheduled
next CPU as interrupt target upon an interrupt
sun4d:
Introduce irq_chip
Introduce dedicated mask/unmask methods
Introduce sun4d_handler_data that allow easy access to
necessary data in mask/unmask fuctions
Rewrote sun4d_handler_irq to use generic irq support
TODO:
The original implmentation of enable/disable had:
if (irq < NR_IRQS)
return;
The new implmentation does not distingush between SBUS and cpu
interrupts.
I am no sure what is right here. I assume we need to do
something for the cpu interrupts.
I have not succeeded booting my sun4d box (with or without this patch)
and my understanding of this platfrom is limited.
So I would be a bit suprised if this works.
leon:
Introduce irq_chip
Store mask in chip_data for use in mask/unmask functions
Add build_device_irq for leon
Use leon_build_device_irq in leon_init_timers
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Daniel Hellstrom <daniel@gaisler.com>
Tested-by: Daniel Hellstrom <daniel@gaisler.com>
Tested-by: Marcel van Nies <morcles@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
- drop filename in file header
- drop unused includes
- add description of sun4m interrupts (from davem)
- add KERN_* to printk
- fix spaces => tabs
- add spaces after reserved words
- drop all externs, they are now in header files
This is partly based on a patch from: David Miller <davem@davemloft.net>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Normally, srmmu uses different trap table register values to allow
determination of the cpu we're on. All of the trap tables have
identical content, they just sit at different offsets from the first
trap table, and the offset shifted down and masked out determines
the cpu we are on.
The code tries to free them up when they aren't actually used
(don't have all 4 cpus, we're on sun4d, etc.) but that causes
problems.
For one thing it triggers false positives in the DMA debugging
code. And fixing that up while preserving this relative offset
thing isn't trivial.
So just kill the freeing code, it costs us at most 3 pages, big
deal...
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: cleanup, futureproof
In fact, all cpumask ops will only be valid (in general) for bit
numbers < nr_cpu_ids. So use that instead of NR_CPUS in various
places.
This is always safe: no cpu number can be >= nr_cpu_ids, and
nr_cpu_ids is initialized to NR_CPUS at boot.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Impact: use new API
Use the accessors rather than frobbing bits directly. Most of this is
in arch code I haven't even compiled, but it is mostly straightforward.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
In preparation for the introduction of a generic swap() macro.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All noise since we don't have CPU hotplug there. However, they
did expose something very odd-looking in there - poke_viking()
does a bunch of identical btfixup each time it's called (i.e.
for each CPU). That one is left alone for now; just the trivial
misannotation fixes.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
arch/sparc/kernel/sun4d_smp.c: In function ‘smp4d_callin’:
arch/sparc/kernel/sun4d_smp.c:101: error: implicit declaration of function ‘notify_cpu_starting’
arch/sparc/kernel/sun4m_smp.c: In function ‘smp4m_callin’:
arch/sparc/kernel/sun4m_smp.c:74: error: implicit declaration of function ‘notify_cpu_starting’
Signed-off-by: Robert Reif <reif@earthlink.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the only use of the clear_profile_irq() btfixup entry,
which just eats up lots of dead space on other platform types.
A subsequent commit will delete the other implementations and
the btfixup entry as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now, there is no notifier that is called on a new cpu, before the new
cpu begins processing interrupts/softirqs.
Various kernel function would need that notification, e.g. kvm works around
by calling smp_call_function_single(), rcu polls cpu_online_map.
The patch adds a CPU_STARTING notification. It also adds a helper function
that sends the message to all cpu_chain handlers.
Tested on x86-64.
All other archs are untested. Especially on sparc, I'm not sure if I got
it right.
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Completely unused, and it just makes the SMP message
passing code on 32-bit sparc look more complex than
it is.
Signed-off-by: David S. Miller <davem@davemloft.net>
calibrate_delay() must be __cpuinit, not __{dev,}init.
I've verified that this is correct for all users.
While doing the latter, I also did the following cleanups:
- remove pointless additional prototypes in C files
- ensure all users #include <linux/delay.h>
This fixes the following section mismatches with CONFIG_HOTPLUG=n,
CONFIG_HOTPLUG_CPU=y:
WARNING: vmlinux.o(.text+0x1128d): Section mismatch: reference to .init.text.1:calibrate_delay (between 'check_cx686_slop' and 'set_cx86_reorder')
WARNING: vmlinux.o(.text+0x25102): Section mismatch: reference to .init.text.1:calibrate_delay (between 'smp_callin' and 'cpu_coregroup_map')
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Christian Zankel <chris@zankel.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move stuff used only by arch/sparc/kernel/* into arch/sparc/kernel/irq.h
and into individual files in there (e.g. macros internal to sun4m_irq.c,
etc.)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.
Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It moves the smp_procesors_ready variable to sun4d_smp.c only.
Signed-off-by: Krzysztof Helt (krzysztof.h1@wp.pl)
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the smp related section mismatch warnings by marking the smp init
functions as cpuinit.
Signed-off-by: Bob Breuer <breuerr@mc.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Todo items:
- IRQ_INPROGRESS flag - use sparc64 irq buckets, or generic irq_desc?
- sun4d
- re-indent large chunks of sun4m_smp.c
- some places assume sequential cpu numbering (i.e. 0,1 instead of 0,2)
Last I checked (with 2.6.14), random programs segfault with dual
HyperSPARC. And with SuperSPARC II's, it seems stable but will
eventually die from a write lock error (wrong lock owner or something).
I haven't tried the HyperSPARC + highmem combination recently, so that
may still be a problem.
Signed-off-by: David S. Miller <davem@davemloft.net>
When we stop allocating percpu memory for not-possible CPUs we must not touch
the percpu data for not-possible CPUs at all. The correct way of doing this
is to test cpu_possible() or to use for_each_cpu().
This patch is a kernel-wide sweep of all instances of NR_CPUS. I found very
few instances of this bug, if any. But the patch converts lots of open-coded
test to use the preferred helper macros.
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Acked-by: Kyle McMartin <kyle@parisc-linux.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Christian Zankel <chris@zankel.net>
Cc: Philippe Elie <phil.el@wanadoo.fr>
Cc: Nathan Scott <nathans@sgi.com>
Cc: Jens Axboe <axboe@suse.de>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
set_page_count usage outside mm/ is limited to setting the refcount to 1.
Remove set_page_count from outside mm/, and replace those users with
init_page_count() and set_page_refcounted().
This allows more debug checking, and tighter control on how code is allowed
to play around with page->_count.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Viresh Kumar