It was not possible to register a UART driver due
to a bad condition.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
PB_BAIL_OUT parameter as to be set to one. This is needed because
digital protocol 1.0 is used in combination with ISO15693 protocol.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NCI deactivate management was modified to support all NCI
deactivation type. Problem is that all the API are not ready
yet for it.
Problem is that with current code, when neard asks to deactivate
the tag it sends a deactivate SLEEP but nobody will then send a
IDLE deactivate. This IDLE deactivate is mandatory since NFC
controller can only be unlocked by DH.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reference Marvell NFC controller as ISO15693 capable.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Marvell NFC USB driver has to be updated to follow new multi
PHY driver interface.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support of Marvell NFC chip controlled over UART
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Declare nfcmrvl platform_data structure and few DT parameters
for nfcmrvl driver.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some NFC controller supports UART as host interface.
As with SPI, a lot of code can be shared between vendor
drivers. This patch add the generic support of UART and
provides some extension API for vendor specific needs.
This code is strongly inspired by the Bluetooth HCI ldisc
implementation. NCI UART vendor drivers will have to register
themselves to this layer via nci_uart_register.
Underlying tty will have to be configured from user land
thanks to an ioctl.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Low level driver can specify a GPIO that will be used to reset
the chip. Thanks to this the driver can ensure the state of the
device at init.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Device ID was not restrictive enough. This patch select the USB
device with the full device and interface characteristics.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Update internal nci recv frame API to use skbuff phy management
to generic part of the driver.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In some configuration NCI packet can be encapsulated in HCI
packets. This patch had the support of this.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
These settings are related to a specific integration that requires
the firmware to drive some GPIOs for external RF coexistency.
Since this is really linked to specific hardware integration let's
remove them.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
STMicroelectronics NFC NCI chips family is extending
with the new ST21NFCC using the AMS AS39230 RF booster.
The st21nfcb driver is relevant for this solution and
might be with future products.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Vendor commands are passed from userspace through the
NFC_CMD_VENDOR netlink command, allowing driver and hardware
specific operations implementations like for example RF tuning
or production line calibration.
Drivers will associate a set of vendor commands to a vendor
id, which could typically be an OUI. The netlink kernel
implementation will try to match the received vendor id
and sub command attributes with the registered ones. When
such match is found, the driver defined sub command routine
is called.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Together with inline routines to associate a vendor commands
array with an NFC device.
Vendor commands allow vendors to implement their very specific
operations from driver code instead of adding new stack ops
for non NFC generic commands.
Vendors need to select their own unique IDs and use that as a
namespace for defining sub commands.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to prevent any NFC feature when NFC is disable and
to save power, (down to 4uA) put the CLF in hibernate mode
with RF deactivated.
Add the equivalent to enable the NFC feature when initiating
the st21nfcb driver.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When st21nfcb is disabled, the irq line may remain active
while no data are available, flooding the system with
irrelevant i2c transaction.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The powered flag can be set from the ndlc_open and ndlc_close layer.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Removing st21nfcb may need to execute some specific commands before
stopping the ndlc state machine.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When closing the device some data (proprietary commands)
might be sent. The core state machine needs to be set for
correct command execution.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
On st21nfcb, nci proprietary commands are available to run
specific chip operations (for example: power management)
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When closing st21nfcb driver, flag ST21NFCB_NCI_RUNNING can be cleared
only once the ndlc and the transport (i2c or spi) layers are released.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to release the st21nfcb properly close the ndlc
layer first.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
ndlc_remove already calls st21nfcb_nci_i2c_disable and
phy->powered is already set to 0.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Once the data is sent, we need to preserve the full frame for
the ndlc state machine. If the NDLC ACK is not received in time,
the ndlc layer will resend the same frame.
Having the header byte pulled will corrupt the frame.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since ndev->driver_data is allocated by devm_kzalloc(), we do not
need the inappropriate kfree to free it in driver's remove function.
Freeing will trigger when driver unloads.
Cc: stable@vger.kernel.org
Acked-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Firo Yang <firogm@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Handle allowing to send proprietary nci commands anywhere in the nci
state machine.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some device may need to execute some proprietary commands
in order to "wake-up"; Before the nci state initialization.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
setup was executed in any case, even if NCI_RESET failed.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Allow for drivers to explicitly define handlers for each
proprietary notifications and responses they expect to support.
Reviewed-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Several of these goto exit; uses should be direct returns
as skb is not yet initialized by nci_hci_get_param().
Miscellanea:
o Use !memcmp instead of memcmp() == 0
o Remove unnecessary goto from if () {... goto exit;} else {...} exit:
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*()
functions) which appeared in v3.17-rc1, the gpiod_get* functions
take an additional parameter that allows to specify direction and
initial value for output.
Use this to simplify the driver. Furthermore this is one caller less
that stops us making the flags argument to gpiod_get*() mandatory.
While touching this also do some minor coding style fixes.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In microread_i2c_irq_thread_fn 'client' set but not used
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
CONFIG_DYNAMIC_DEBUG is the right toggle to enable pr_debug().
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The current versions of the trf7970a has an erratum where it returns
an extra byte in the response to 'Read Multiple Block' (RMB) commands.
This command is issued to Type 5 tags (i.e., ISO/IEC 15693 tags) by
the neard daemon.
To handle this, define a new Device Tree property,
't5t-rmb-extra-byte-quirk', which indicates that the associated
trf7970a device has this erratum. The trf7970a device driver
will then ensure that the response length to RMB commands is
reduced by one byte (for devices with the erratum).
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When GPIO is not enabled we hit this kind of warning:
drivers/nfc/nxp-nci/i2c.c: In function 'nxp_nci_i2c_acpi_config':
drivers/nfc/nxp-nci/i2c.c:320:2: error: implicit declaration of function 'devm_gpiod_get_index' [-Werror=implicit-function-declaration]
gpiod_en = devm_gpiod_get_index(&client->dev, NULL, 2);
This is fixed by explicitely including gpio/consumer.h.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Update the AFE_TX_CONFIG value to solve marginal rise/fall issues
observed when the link is operating in 100BaseT. This workaround applies
to GPHY revisions D0, E0 and newer.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jaeden Amero says:
====================
net/phy: micrel: Center FLP timing at 16ms
In v2, we add an additional cleanup commit to make an array of strings
static const and to improve const correctness generally. We also no longer
unnecessarily initialize the result variable in
ksz9031_center_flp_timing().
In v3, we remove the unnecessary result variable from ksz9031_config_init()
introduced by a previous version of "net/phy: micrel: Center FLP timing at
16ms".
In v4, we modify the commit message of "net/phy: micrel: Center FLP timing
at 16ms" to replace the awkward quotation of the data sheet's programming
procedure with an explanation of why we program the FLP burst registers and
restart auto-negotiation where we do (config_init).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Link failures have been observed when using the KSZ9031 with HP 1810-8G
and HP 1910-8G network switches. Center the FLP timing at 16ms to help
avoid intermittent link failures.
>From the KSZ9031RNX and KSZ9031MNX data sheets revision 2.2, section
"Auto-Negotiation Timing":
The KSZ9031[RNX or MNX] Fast Link Pulse (FLP) burst-to-burst
transmit timing for Auto-Negotiation defaults to 8ms. IEEE 802.3
Standard specifies this timing to be 16ms +/-8ms. Some PHY link
partners need to receive the FLP with 16ms centered timing;
otherwise, there can be intermittent link failures and long
link-up times.
The PHY data sheet recommends configuring the FLP burst registers after
power-up/reset and immediately thereafter restarting auto-negotiation, so
we center the FLP timing at 16ms and then restart auto-negotiation in the
config_init for KSZ9031.
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some defines for a few pad skew related extended registers.
Specify for which MMD Address (dev_addr) they are for.
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a few places in this driver, we weren't using const where we could
have. Use const more.
In addition, change the arrays of strings in ksz9031_config_init() to be
not only const, but also static.
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Alexander Duyck pointed out that:
struct tnode {
...
struct key_vector kv[1];
}
The kv[1] member of struct tnode is an arry that refernced by
a null pointer will not crash the system, like this:
struct tnode *p = NULL;
struct key_vector *kv = p->kv;
As such p->kv doesn't actually dereference anything, it is simply a
means for getting the offset to the array from the pointer p.
This patch make the code more regular to avoid making people feel
odd when they look at the code.
Signed-off-by: Firo Yang <firogm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
API compliance scanning with coccinelle flagged:
./drivers/net/wan/dscc4.c:1036:1-33:
WARNING: timeout (10) seems HZ dependent
./drivers/net/wan/dscc4.c:554:2-34:
WARNING: timeout (10) seems HZ dependent
./drivers/net/wan/dscc4.c:599:2-34:
WARNING: timeout (10) seems HZ dependent
Numeric constants passed to schedule_timeout_*() make the effective
timeout HZ dependent which does not seem to be the intent here.
Fixed up by converting the constant to jiffies with msecs_to_jiffies(),
passing 100ms (assuming HZ==100 in the original code).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
API compliance scanning with coccinelle flagged:
./drivers/net/wan/cosa.c:520:2-18: WARNING:
timeout (30) seems HZ dependent
Numeric constants passed to schedule_timeout() make the effective
timeout HZ dependent which makes little sense in a device probe.
Fixed up by converting the constant to jiffies with msecs_to_jiffies()
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix static checker warnings in the flow of system guid query.
Fixes: 707c4602cd ('net/mlx5_core: Add new query HCA vport commands')
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In big endian cases, macro cpu_to_le16 unfolds to __swab16 which
provides special case for constants. In little endian cases,
__constant_cpu_to_le16 and cpu_to_le16 expand directly to the
same expression. So, replace __constant_cpu_to_le16 with
cpu_to_le16 with the goal of getting rid of the definition of
__constant_cpu_to_le16 completely.
The semantic patch that performs this transformation is as follows:
@@expression x;@@
- __constant_cpu_to_le16(x)
+ cpu_to_le16(x)
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vincent Cuissard